Using a 110v G4 DP 867 in the UK 220v
I cant get a clear answer from anyone regarding using my DP 867(USA) that i want to take to the UK. Does it have an auto voltage sensor? Do I need to buy a transformer?
Any help would be appreciated.
4061
Hi Bobby,
This model has Auto-Switching Power Supply.
Rob is right:
Voltage specs are visible (mandatory) on any electric device PSU. Better double-check always (about Manual vs. Auto-Switch models).
No transformer needed.
Axl
Similar Messages
-
I will use my 110V MacBook in the Philippines which has 220V sockets. Will the World Travel Adapter Kit help me?
Assuming you're in North America now, you probably won't need any sort of plug adaptor there; most sockets in the Philippines are the same as those in North America. In case you do, it doesn't contain the correct adaptor.
Voltage conversion is handled by the MacBook without any additional components.
(66079) -
i bought my macbook pro in the US. can i use it in china? (P.S the power in the US is 110v, in China is 220v, however, the mac power supply has said: "Input: 100~240v")
The Magsafe autoswitches based on detected power. You will likely need a wall adapter to alter ther US-based 3-prong to whatever is used in China.
-
What is the maximum hard drive replacement I can use on my PowerBook g4 867 ghz?
What is the maximum hard drive replacement I can use on my PowerBook g4 867 ghz?
Sorry we are late. This forum is getting less traffic as people upgrade and responses sometime take longer. Everyone here volunteers their time, and I for one was unavailable much of yesterday.
The limiting factor on max drive size is that your PowerBook uses the older PATA drive interface, and the largest PATA 2.5-inch drives available today are about 320 GB.
What I'm reserching is the ATA bus controller in your PowerBook. Some older Macs cannot recognize more than 128GB of PATA hard drive space. However, this archived discussion from 2008:
https://discussions.apple.com/thread/1413918?start=0&tstart=0
suggests that people are running PowerBooks older than yours and not suffering the 128GB limit.
At this point, I need help with what appears to be a descrepancy between the text of your post and the PowerBook in your profile. A "PowerBook6,2" model identifier returns to the "PowerBook G4 (12-inch DVI)" marketing name with a 1.0Ghz processor; the 12-inch PBG4 with a 867mHz processor shows a model identifier of PowerBook6.1. They show the same hard drive interface but the later on appears to be a sure bet for large hard drive support, -
Using US 110V AirPort Express in Europe with 220V?
Hello all,
I want to use my 110 V Air Port Express (US Version) in Europe at 220V.
I know, that the sticker on the Express module says "110V".
I also found the tech specs, which state usage from 110V to 240V (http://www.apple.com/airportexpress/specs.html)
And, I know that my power supply for my MacMini says 110V on the sticker as well, the tech specs state 110 to 240 V and it indeed works fine with 240V.
I ASSUME that the airport express will be just fine - but it would be nice if someone could confirm. No need to fry more devices than nescessary....
Any help/input is greatly appreciated...
M.Waenni 2 wrote:
Hello all,
I want to use my 110 V Air Port Express (US Version) in Europe at 220V.
I know, that the sticker on the Express module says "110V".
I also found the tech specs, which state usage from 110V to 240V (http://www.apple.com/airportexpress/specs.html)
And, I know that my power supply for my MacMini says 110V on the sticker as well, the tech specs state 110 to 240 V and it indeed works fine with 240V.
I ASSUME that the airport express will be just fine - but it would be nice if someone could confirm. No need to fry more devices than nescessary....
the express will handle the power issue quite well. however, i'm not sure if you don't run into problems with the channels it is broadcasting on. from the AX tech specs:
Channels
+Channels 1-11, 36-48, and 149-165 approved for use in the United States and Canada+
+Channels 1-13 and 36-64 approved for use in Japan+
+Channels 1-13 and 36-140 approved for use in Europe+
+Channels 1-13, 36-64, and 149-165 approved for use in Australia, Hong Kong, and New Zealand+ -
Unable To Use DVDSP4 Presets for HD-DVD in the H.264 Format
I recently prepared a 23 minute slide show using Fotomagico from high resolution Hasselblad slides scanned in at 1200 dpi. Within Fotomagico I rendered the Fotomagico slide show to Apple ProRes 422 HQ, took it into Final Cut Pro 6.03 and added an intro and closing section. I then sent this to Compressor and selected the 30 minute HD-DVD preset which uses mpeg2. All went fine with the encoding to mpeg2 and I got a successful build and format out of DVDSP4 after importing the resulting .m2v file into DVDSP4. However, while the disk plays back fine in my Mac Pro it plays back with stuttering (audio and video) on my Toshiba HD-A2 HD-DVD player. I used a Verbatim Datalife DVD+R, but several other discs from other manufactuers including a DVD-R disc showed the same problem.
Please note that I have the latest firmware on my Toshiba HD-A2 and I have successfully burned RL HD-DVD discs using my PC and Windows software (Ulead's DVD Movie Factory 6+) which play fine without stuttering on my HD-A2.
I then decided to send the project to Compressor and use the 60 minute HD-DVD preset that encodes to H.264. Once again Compressor successfully executed the encode of my 23 minute slide show and it plays fine in QuickTime or MPEG StreamClip. However, every time I try and import this .mov file encoded in H.264 using the Compressor preset for HD-DVD into DVDSP4, DVDSP4 brings it in to the assets folder, but after a couple of seconds DVDSP4 crashes. Using console I get a message that DVDSP4 quit unexpectedly due to a "segmentation fault".
I also tried to take the ProRes Fotomagic project in Final Cut Pro 6.02 and send it out with Quicktime Conversion using the H.264 codec. Again I have a file that plays fine in QT, but when I try and import this .mov file into DVDSP4, I get the message "imcompatible format".
In summary, I am completely frustrated after many many hours of work at trying to prepare an HD-DVD on red laser of my slide show in DVDSP4. I cannot figure out what I am doing wrong, and I would be most appreciative of any suggestions anyone may have.
Thanks in advance.
TomAm I the only person who has ever tried to use the Presets in Compressor 3 for encoding HD-DVD disks? I would like to use these presets for burning HD-DVD's to standard red laser media as I have done on my PC. With the mpeg2 Preset I can get nothing but stuttering video when played back on my Toshiba HD-A2 and when I use Compressor 3 to encode with either of the H264 presets, the resulting .mov file causes DVDSP4 to crash when I import the file. Has no one else experienced this? Does anyone have any thoughts on addressing these issues other than to go back to working on my PC?
Tom -
I did made a copy of all my CC programms. for using on my other workstation. now is the CC desktop app not syncing the programme information. it do not see or sync the installed programms properly. what can i do. i do not want to download the hols set. because of a slow connection
If you are getting emails from these forums then you probably accidentally clicked on one of the links on the forums page where all the questions are listed e.g. at the top right of each forum's page there is text box with Actions and Notifications in :
So far you've posted in the iTunes Store forum :
https://discussions.apple.com/community/itunes/itunes_store#/
And the Using iPad forum :
https://discussions.apple.com/community/ipad/using_ipad#/
If on either of those forums that box says 'stop email notifications' instead of 'receive' then click on it and it should stop that forum sending emails to you.
There are full instructions on this page for stopping emails, as there are other places where they might have been set 'on' : https://discussions.apple.com/docs/DOC-3661
This is your original post for iTunes Match : https://discussions.apple.com/message/22647293#22647293
And this page lists your posts (you can click on each post on it to be taken to it's thread) : https://discussions.apple.com/people/suzettemg?view=overview -
hi Experts,
while running SQL Query i am getting an error as
The text, ntext, and image data types cannot be compared or sorted, except when using IS NULL or LIKE operator. for the query
select T1. Dscription,T1.docEntry,T1.Quantity,T1.Price ,
T2.LineText
from OQUT T0 INNER JOIN QUT1 T1 ON T0.DocEntry = T1.DocEntry INNER JOIN
QUT10 T2 ON T1.DocEntry = T2.DocEntry where T1.DocEntry='590'
group by T1. Dscription,T1.docEntry,T1.Quantity,T1.Price
,T2.LineText
how to resolve the issueDear Meghanath,
Please use the following query, Hope your purpose will serve.
select T1. Dscription,T1.docEntry,T1.Quantity,T1.Price ,
CAST(T2.LineText as nvarchar (MAX))[LineText]
from OQUT T0 INNER JOIN QUT1 T1 ON T0.DocEntry = T1.DocEntry LEFT OUTER JOIN
QUT10 T2 ON T1.DocEntry = T2.DocEntry --where T1.DocEntry='590'
group by T1. Dscription,T1.docEntry,T1.Quantity,T1.Price
,CAST(T2.LineText as nvarchar (MAX))
Regards,
Amit -
How do I use cookies to control which part of the timeline to play from?
Hi there,
I have created an animation with Adobe Edge. My site uses Concrete5 and I am pulling in the Edge content into an IFRAME on my home page (there my be a better way to do this and I'm open to suggestions). I want the animation to play from the start when someone first visits the site, but if during their browser session they navigate back to the home page, I want the animation to only play a shorter segment of frames near the end.
My question is, how do I use cookies to acheive this? I'm new to javascript/jquery.
I've included the following code on compositionReady, (found in another post on this forum) but don't have a clue how to continue...
// insert code to be run when the composition is fully loaded here yepnope( { nope:[ '/js/jquery.cookie.js' ], complete: init } ); function init() { //create your cookie's initial values here }
My temp site is here - http://79.170.40.43/nutcrackerdesign.co.uk/
On revisting the homepage, I only want to play from when the green 'How can we help?' button drops in.
Many thanks!
RussHi, Russ-
I found this article, which seemed really helpful in describing how cookies work in JavaScript:
http://www.quirksmode.org/js/cookies.html
Remember that JS works just fine within Animate, so on your compositionReady, you can read your cookie and then set the play based on that. You should probably uncheck the autoplay for your Stage and control the play of your Stage from the compositionReady.
Good luck!
-Elaine -
I have bought an used Iphone 5. I dont have the password for the existing login id of the old owner. How do i use the phone and change the log in id?
Unfortunatly the only way that you can get it off is to get the old user to input the password. You may need to contact that old user and see if he can put the old password in. hope this helps.
-
When I download firefox, using recommended setting, or my own, all the sub files/folders like plugins, modules, updater end up on the desktop as well as in the file location. And when I try to put them into the file location, they don't. And when I delete them, FireFox won't open. I tried deleting FireFox and reinstalling it multiple times, and a message pops up sometimes that says FireFox may not have installed correctly, so I follow the steps, but all the extra icons on my desktop don't go away. This has happened every time I have downloaded FireFox. The browser itself works, but I need to know how to get rid of these icons, but still be able to use FireFox. This is on a new computer, with Windows 7.
== I downloaded FireFox. ==
== User Agent ==
Mozilla/5.0 (Windows; U; Windows NT 6.1; en-US; rv:1.9.2.6) Gecko/20100625 Firefox/3.6.6Managed to solve this myself. Just went to properties > hidden.
-
I have a new iphone and cannot delete the backup from icloud. It says that it is in use. I have read some of the other threads and it only seems to be haphazard solutions. Is there a definite way to fix this? I am not able to change icloud accounts.
Follow the steps in wjosten's post here: https://discussions.apple.com/message/13356770#13356770 (for Windows, substitute Outlook in step 2).
-
Hi Friends...
I’m trying to delete a back-up file on mu TC but I get the message “The operation could not be completed because the item “bands” is in use. I’d like to start the Back from scratch, could help me out with deleting the current file?Sorry, I am very confused. I asked the following question....
Is this the only backup file on your Mac, or do you have other backup files and data on the Time Capsule disk?
The answer that you gave was....
This is the only one
Now you are saying that....
But I have lots of other files on Time Capsule! The back up file is only one of them.
Can you clarify, please? -
I know nothing about how to use my new ipod and when reading the little information that came with it, all I can do is turn it on. Then in a few seconds it goes black, never having brought up a screen to do anything! Help! What do I do to get this thing going?
You might consider connecting it to the charger and charging up the battery overnight.
Please Get the iPod Touch User Manual for iOS 5 -
Querying on a value and using that to pull other data in the same query
I am having some issues pulling the correct data in a query. There is a table that houses application decision data that has a certain decision code in it, WA, for a particular population of applicants. These applicants also may have other records in the same table with different decision codes. Some applicants do NOT have WA as a decision code at all. What I need to do is pull anyone whose maximum sequence number in the table is associated with the WA decision code, then list all other decision codes that are also associated with the same applicant. These do not necessarily need pivoted, so long as I can pull all the records for a person whose highest sequence number is associated with WA and all of the other decision codes for that applicant for the same term code and application number also appear as rows in the output.
I do not have the rights in Oracle to create tables, so please pardon if this code to make the table is incorrect or doesn't show up here as code. This is not the entire SARAPPD table framework, just the pertinent columns, along with some data to put in them.
DROP TABLE SARAPPD;
CREATE TABLE SARAPPD
(PIDM NUMBER(8),
TERM_CODE_ENTRY VARCHAR2(6 CHAR),
APDC_CODE VARCHAR2(2 CHAR),
APPL_NO NUMBER(2),
SEQ_NO NUMBER(2));
INSERT INTO SARAPPD VALUES (12345,'201280','WA',1,4);
INSERT INTO SARAPPD VALUES (12345,'201280','RE',1,3);
INSERT INTO SARAPPD VALUES (12345,'201280','AC',1,2);
INSERT INTO SARAPPD VALUES (23456,'201280','RE',1,2);
INSERT INTO SARAPPD VALUES (23456,'201280','WA',1,3);
INSERT INTO SARAPPD VALUES (23456,'201280','SC',1,1);
INSERT INTO SARAPPD VALUES (34567,'201280','AC',1,1);
INSERT INTO SARAPPD VALUES (45678,'201210','AC',2,1);
INSERT INTO SARAPPD VALUES (45678,'201280','AC',1,2);
INSERT INTO SARAPPD VALUES (45678,'201280','WA',1,3);
INSERT INTO SARAPPD VALUES (56789,'201210','SC',1,2);
INSERT INTO SARAPPD VALUES (56789,'201210','WA',1,3);
COMMIT;I have attempted to get the data with a query similar to the following:
WITH CURR_ADMIT AS
SELECT C.SEQ_NO "CURR_ADMIT_SEQ_NO",
C.PIDM "CURR_ADMIT_PIDM",
C.TERM_CODE_ENTRY "CURR_ADMIT_TERM",
C.APDC_CODE "CURR_ADMIT_APDC",
C.APPL_NO "CURR_ADMIT_APPNO"
FROM SARAPPD C
WHERE C.TERM_CODE_ENTRY IN ('201210','201280')
AND C.APDC_CODE='WA'
AND C.SEQ_NO=(select MAX(d.seq_no)
FROM sarappd d
WHERE d.pidm = C.pidm
AND d.term_code_entry = C._term_code_entry)
select sarappd.pidm,
sarappd.term_code_entry,
sarappd.apdc_code,
curr_admit.CURR_ADMIT_SEQ_NO,
sarappd.appl_no,
sarappd.seq_no
from sarappd,curr_admit
WHERE sarappd.pidm=curr_admit.PIDM
and sarappd.term_code_entry=curr_admit.TERM_CODE_ENTRY
AND sarappd.appl_no=curr_admit.APPL_NOIt pulls the people who have WA decision codes, but does not include any other records if there are other decision codes. I have gone into the user front end of the database and verified the information. What is in the output is correct, but it doesn't have other decision codes for that person for the same term and application number.
Thanks in advance for any assistance that you might be able to provide. I am doing the best I can to describe what I need.
Michelle Craig
Data Coordinator
Admissions Operations and Transfer Systems
Kent State UniversityHi, Michelle,
903509 wrote:
I do not have the rights in Oracle to create tables, so please pardon if this code to make the table is incorrect or doesn't show up here as code. This is not the entire SARAPPD table framework, just the pertinent columns, along with some data to put in them. You really ought to get the necessary privileges, in a schema that doesn't have the power to do much harm, in a development database. If you're expected to develop code, you need to be able to fabricate test data.
Until you get those privileges, you can post sample data in the form of a WITH clause, like this:
WITH sarappd AS
SELECT 12345 AS pidm, '201280' AS term_code_entry, 'WA' AS apdc_code , 1 AS appl_no, 4 AS seq_no FROM dual UNION ALL
SELECT 12345, '201280', 'RE', 1, 3 FROM dual UNION ALL
SELECT 12345, '201280', 'AC', 1, 2 FROM dual UNION ALL
... I have attempted to get the data with a query similar to the following:
WITH CURR_ADMIT AS
SELECT C.SEQ_NO "CURR_ADMIT_SEQ_NO",
C.PIDM "CURR_ADMIT_PIDM",
C.TERM_CODE_ENTRY "CURR_ADMIT_TERM",
C.APDC_CODE "CURR_ADMIT_APDC",
C.APPL_NO "CURR_ADMIT_APPNO"
FROM SARAPPD C
WHERE C.TERM_CODE_ENTRY IN ('201210','201280')
AND C.APDC_CODE='WA'
AND C.SEQ_NO=(select MAX(d.seq_no)
FROM sarappd d
WHERE d.pidm = C.pidm
AND d.term_code_entry = C._term_code_entry)
Are you sure this is what you're actually running? There are errors. such as referencing a column called termcode_entry (starting with an underscore) at the end of the fragment above. Make sure what you post is accurate.
Here's one way to do what you requested
WITH got_last_values AS
SELECT sarappd.* -- or list all the columns you want
, FIRST_VALUE (seq_no) OVER ( PARTITION BY pidm
ORDER BY seq_no DESC
) AS last_seq_no
, FIRST_VALUE (apdc_code) OVER ( PARTITION BY pidm
ORDER BY seq_no DESC
) AS last_apdc_code
FROM sarappd
WHERE term_code_entry IN ( '201210'
, '201280'
SELECT pidm
, term_code_entry
, apdc_code
, last_seq_no
, appl_no
, seq_no
FROM got_last_values
WHERE last_apdc_code = 'WA'
;Don't forget to post the results you want from the sample data given.
This is the output I get from the sample data you posted:
` PIDM TERM_C AP LAST_SEQ_NO APPL_NO SEQ_NO
23456 201280 WA 3 1 3
23456 201280 RE 3 1 2
23456 201280 SC 3 1 1
45678 201280 WA 3 1 3
45678 201280 AC 3 1 2
45678 201210 AC 3 2 1
56789 201210 WA 3 1 3
56789 201210 SC 3 1 2I assume that the combination (pidm, seq_no) is unique.
There's an analytic LAST_VALUE function as well as FIRST_VALUE. It's simpler (if less intuitive) to use FIRST_VALUE in this problem because of the default windowing in analytic functions that have an ORDER BY clause.
Maybe you are looking for
-
A lot of time waisted on embedding fonts! Please advise!
I am trying to embed this (attached) font for the second day! I know that it is not how it should be. Please help me if you know how. This is Mac. I added this font in Flash library and also created a dynamic field with it and embedded it from there.
-
Exporting Versions to a specific pixel size
I want to export files for a slideshow that requires a pixel size of 1900 x 1200 , can it be done in Aperture ? , I have tried modifying the export preset , it does not work with (Fit Within ) is there another way ? Thanks Ray
-
Servlets Vs Standalone Application?
Servlets Vs Standalone Application? I know this is an extremely broad subject, but put very simply can anyone give me a basic list of pros & cons in writing an application on a network with either of the two mentioned technologies?!? We will need sec
-
Frequently while typing my screen goes black and then flashes back to home screen. I have shut down & restarted. I have the newest update. It has always done this but appears to be more often now. Thx
-
TS1424 iTunes Download Error 8008
I have just purchased a movie off the itunes store- and its insanly slow- then glitching and giving me an Error message the the file maybe corrupt? Error message 8008.... Any advice on fixes?