Using a Range Extender with WLC & LWAP

Hi,
is it possible to use a Wireless range extender with a WLAN installation of LWAPs & WLC?
Is there a security setting in the WLC that prevents multiple clients connecting through the range extender?
Any advise would be appreciated.
Regards,
Chris

No.
Range extenders are horrible devices that kill your bandwitdh, increase the collision rate and would totally kill the radio management algorithm. For this reason they are not supported and you should not even look into them. They were more popular when you had very few IOS APs and the speed rates were low. I'm not sure that 11n range extenders actually exist.
Anyway, if you want to extend the range, you could look into bridging APs or mesh APs (AP not connected via wire, uses 5ghz band for backhaul transport to root AP and 2ghz to server clients).

Similar Messages

Can i use a cisco RE1000 range extender with airport extreme

Can I use a Cisco R1000 range extender with airport extreme?

Apple's "extend a wireless network" function appears to be a proprietary feature that will only work with other Apple routers.
As far as we know, devices from other manufacturers are not compatible with this feature.
Bottom line....It would be extremely unlikely that this would work, but it's worth a try if you already have the products in hand.
Please post on your results.

Using Belkin Dual-Band Wirleless Range Extender with Apple Ipad Air

Can I use the above Belkin Range Extender with the Apple Ipad on wi-fi? If so, which port do I hook up the extender to on the ipad? Thanks.

I wanted to chime in on this thread with my experince as it came up in a Google search while i had the same problem.
I actually got this working with an e4200v2 but only after hours of headache and dealing with tech support (both chat and phone)
First, I can tell you that support was nearly usless for me...the chat representative actually SIGNED OUT of chat after her intial troubleshooting steps failed to fix my problem. (This was not from lack of politeness or understanding on my end, I know it's just people trying to do their job.)
Phone support was much more thurough but still just walked me through steps I had already done on my own previously (I was formally a network tech.) This included running manual setup both wired to my e4200v2 and wireleslly. Attempting different channels and moving the RE1000 to various spots in my house. Their conclusion was that i needed to RMA the device.
THE ACTUAL PROBLEM:
It turns out the issue (for me at least) was not that the RE1000 was too weak but that the e4200v2 was too strong. The devices in my house that I wanted to use the RE1000 for were already getting roughly 2-3 bars (out of 5) signal and as such were not connecting to the RE1000. This means that even though the setup completed "successfuly" I wasn't getting any singal or speed improvement.
THE FIX:
So the way I ended up getting this to work was to run the setup software with the device in a location of my house were the RE1000 was only getting about 2-3 bars of service. (You can check this in the RE1000s firmware under "wireless").
I now have full signal and good speeds throughout my house.
I don't know if this is specific to the e4200v2 or just any router with a strong signal but my suggestion for fellow e4200v2 owners is to basically run setup with this guy as far away from your router (but within signal range) as possible.
Cheers,
G

I am trig to connect my apple range extender with my xfinity router

Hi
I am tryong to use my apple range extender with my xfinity rouder, is this possible

Apple range extender? There is no such thing... Do you have an Airport Express?
Plus you have Xfinity... owned by the nations most annoying and not loved ISP.
Good luck.
However, not all is lost, I recommend getting an Ethernet cable and run it between the two points you wish to cover with wifi.
Plug one end into the Xfinity LAN side, plug the other end into the Airport and configure the wifi name accordingly.

Can I use Netgear powerline range extender with Actiontec router M1424WR-D?

We have been using FIOS internet happily with an Actiontec router (M1424WR-D) since 2008, but we have a 'dead zone' in a remote part of our home. I am attempting to install a Netgear Powerline AV 200 Wireless N-Extender kit in the dead zone room, but have not been successful. If I give a unique SSID to the extender, and do not set any encryption, I am able to have wireless connection in the room, but having unprotected wireless connection is unacceptable to me. If I use the same SSID for extender and Actiontec router, and use the same encryption key for the extender as is used on the Actiontec router, then I no longer have wireless connection in the room. I hope someone can provide some help in understanding what it is I'm doing wrong in setting up this powerline extender. Should the extender have the same SSID and encryption key? Should it be a different one? Thanks for any help.
Solved!
Go to Solution.

Great news! At last I finally have been able to get a Netgear Powerline AV200 Wireless-N Extender Kit to provide wifi in the 'dead zone' in our house, and I was able to secure the network with an encryption key which I set up wirelessly, instead of relying on the 'wired' security option offered by the kit (a push-button on the side of the extender box). None of the phone techs at Netgear were able to figure out why we could not get the kit to work properly to begin with, and I finally gave up on the phone techs.
For anyone interested in using this product and who needs to set it up with a non-Netgear router, or a router that does not have a WPS button on it, please be aware that the resource CD in the box may be out of date. You will need to go to Netgear's website and download the Powerline Utility software for your device directly from the website. You will need to supply your product serial number in order to get the download. It is important to have this up-to-date software. I discovered that the up-to-date software downloaded from Netgear functioned more smoothly and allowed me to set up my encryption effortlessly. After forcing a factory reset on the extender and removing the device IP addresses associated with the initial unsuccessful attempt to create a secure network, I was able to set up the extender and secure it with absolutely no problem. The up-to-date software seemed to be the critical factor. The product seems to be working really well now and so far we are happy with it.
A word of caution when dealing with Netgear's phone techs. On some occasions when I phoned into Netgear my case was farmed out to a company called i-Yogi. I had a disturbing experience with one of the techs at i-Yogi. One of the i-Yogi techs said he could help me to set up encryption on my network using the AV200 extender, but that he needed first to gain remote access to my laptop. He also wanted access to another laptop in our house in addition to the one I was working from. This seemed odd and I refused to allow access to the second laptop. After gaining remote access he noted that I was using Norton 360 and he claimed that it was not working with my XP operating system and attempted to sell me a copy of McAfee security software at a reduced rate. He became very pushy about this. I refused to engage in this purchase and insisted that he return to the task of troubleshooting my encryption issue. At this point he still had not once attended to the configuration of the extender settings at all, but even so he refused to assist me, saying that it was not his problem that my network was not secured. It was not a good experience, and I believe he had a totally different agenda than dealing with my technical issue.

Am I able to use a Hawking 300 Range Extender with the Apple Extreme connected to a PC?

I am puchasing an Apple Extreme to replace a Linksys router connected to a PC with Win7. I have been using two Hawking 300 Range extenders to get a better single throughout my home. Will I be able to continue to connect the Hawking 300 Range Extenders to the Apple Extreme?

Will I be able to continue to connect the Hawking 300 Range Extenders to the Apple Extreme?
Apple's "extend a wireless network" feature on the AirPort Extreme appears to be a proprietary setting that only works with other Apple products.
So, it is extremely unlikely that the Hawking devices will work with the AirPort Extreme.
No harm in trying though.
Please post on your findings.

Can I use my 2010 AirPort Extreme as a range extender with a new AirPort Extreme?

I want to use an existing AirPort Extreme (2010 model) with a new AirPort Extreme to extend the range and signal strength into a shop. They are different designations, one n and the other ac. Are they compatible. I need to know before I buy the new router.

The new AirPort Extreme will provide an ac,n,g,b compatible wireless signal.
The existing AirPort Extreme can be configured to extend the n,g,b signal, but it cannot extend the ac signal.

Extreme range - extend with Express?

Hello:
What kind of range should I expect with an AirPort Extreme base station? If it's not enough, can you extend it with just an AirPort Express plugged in somewhere in between? If so, can you extend the network and use the Express' Air Tunes function simultaneously?

Apple quotes 150 ft as the standard, however, range is so dependent upon density of the buildings etc so it's difficult to get that far in practise.
You can extend the range using WDS (there's one explanation of how to do this here: http://arstechnica.com/reviews/hardware/airportexpress.ars/4 ) and, yes, you can use Air Tunes simultaneously.

Using MS Radius Server with WLC

I'm currenlty running WLC version 4.1.171. For authentication I'm using Microsoft IAS. I was able to get this to work by using Web Authentication but I want to use 802.1x w/ PEAP. I've been researching this and most of the documents talk about ACS. I did find one document on how to make this work, however I still have not been able to get authenicated. I'm hoping someone has some documentation on how to configure IAS on MS WIN Ser 2003. Thanks in advance.
Here is the document I've been using: http://wireless.dweezle.org/Docs/PEAP/Step-by-Step%20Guide%20for%20Setting%20Up%20Secure%20Wireless%20Access.ppt

Hi,
can You send me some information about configuring WEB-AUTH with IAS ?
I cannot figure how to comfigure user / ias in my server .
I've done EAPTLS with the same IAS, but now i was trying to do simple user/pass authentication, if it's possible.
Many thanks
Luigi

Using Ohaus Ranger scale with NI 9870 (cRIO)

Hello,
I am using a NI cRIO-9074 data aquisition system with a NI 9870 4-Port, RS232 Serial Interface Module, and am programming with LabView 2012. I'm currently looking for a scale with an RS-232 output that I can plug into the NI 9870 to receive and store measurement data. I'd like to go with an Ohaus Ranger 7000 scale, model number R71MD3. However, looking at NI's list of instrumentation drivers, they do not have anything listed for this model, though they do have quite a few for other (seemingly older) Ohaus scales.
Are drivers not needed for this scale? Or is there a standard RS-232 that can be used? I'd like to ensure that this setup will work before purchasing the scale.
Thanks!

Using the 9870 in a cRIO essentially just adds 4 more COM ports to the cRIO, which you can interface with using NI-VISA. Check this KB for more details. Most "instrument drivers" are just an abstraction layer or wrapper for the low-level VISA reads and writes being performed. If an instrument driver does not already exist, you can implement a simple one yourself using VISA.
In this situation, you'll simply need to look up the command/instruction set the device uses, and implement those using VISA reads and writes. As long as the command set isn't too extensive, this is pretty simple and quick.
So, this setup will definitely work, you'll just need to take the time to implement the VISA commands yourself.

Time Capsule Wireless Range Extended with AirPort Express

I recently was able to (finally) get my Time Capsule working with my previous 2WIRE modem/router (DSL through ATT). This took hours, but it was worth it! Time Capsule is now my primary router with it "bridged" with the 2WIRE device which is now only a modem. Back up is working fine with our three Apple laptops. However, the wireless signal is weaker than when it was set up with the 2WIRE alone. Our signal strength upstairs was weak making internet connection VERY slow and frustrating. I got an AirPort Express to see if I could use it to boost/extend the wireless signal from the Time Capsule unit. Set up was simple, and it is working great! I have it plugged into a wall outlet between the Time Capsule and the stairs leading upstairs. The wireless signal is now "full" everywhere in the house!

Wired Ethernet from the TC to the AirPort Extreme will result in much better performance. It sounds as if you are not configuring the AirPort Extreme correctly.
Please try the following steps carefully:
Unplug the Ethernet cable from the AirPort Exteme if it is not already unplugged. With the AirPort Extreme powered on, hold in the reset button on the Extreme for 10 seconds and release. Allow a full minute for the Extreme to restart
Connect the Ethernet cable to the WAN "O" port on the Extreme.
Click the AirPort icon at the top of the Mac's screen and wait a few seconds for a listing of New AirPort Base Station to appear. Just below that, click on AirPort Extreme.
The example below displays an AirPort Express. You will see AirPort Extreme.
AirPort Setup will open up automatically and take a minute to analyze the network, then announce that the Extreme will be configured to extend the Time Capsule network.
Enter a device name that you want to use for the Exterme and click Next
Wait a minute while AirPort Setup configures everything for you. When you see the message of Setup Complete, click Done.
That's it. Pretty simple. Things should be working fine now.

Dlink Wireless Range Extender with Time Capsule Setup

Looking to setup a D-Link DAP-1320 on my time capsule to extend my wifi network. The D-link instructions are pretty basic, only two choices. WPS Setup, which the Time capsule does not have. And Web browser setup by going to dlinkap.local which only times out and does not load.
Any sugestions? thanks

Nope this cannot work.. Apple to Apple .. Dlink is banana.. Apples don't talk to bananas.
If the DAP-1320 has a WAP mode.. then plug it by ethernet into the TC and use like that. Not going to work any other way.

Which range extender works with the Linksys CIT400 phone?

Which range extender works with the Linksys CIT400 VoIP phone? Can I use any range extender from any other comany or does it have to be one from Linksys? I am not sure if the CIT400 uses standard frequences.
On a side note, where's the forum for the phones? I see one in the archives section which seems to be ready only.

You can use the Linksys WRE54G range expander. For that matter, any 2.4Ghz range expander will work. But what’s more important is what router you would be using the range expander with!! Which router are you using?

HT4260 Can I use a Netgear Universal WN3000RP Wi-Fi Range Extender?

Can I use a Netgear Universal WN3000RP Wi-Fi Range Extender with my Airport Express to extend the range?
If so, is there anything that I need to do in order to configure my computer for it to work properly?
Are there any disadvanges to doing this (speed, signal strength)?
Thanks.

You always want to stay with the same manufacturer if possible for your wireless needs to insure compatibility. If you have a recent version AirPort Express now, using another Express to "extend" the wireless signal will usually work well if there are not too many obstructions for the signal to overcome.
We cannot say if the Netgear device might work for you or not.....it was not compatible with Apple when we tried a sample a few months ago.....but with wireless, you never really know.
Let's just say that the product may not be as "universal" as the title might suggest. There are likely some footnotes in the Netgear materials that their product will not work with devices that use "proprietary" settings, as Apple does.
If you try the Netgear device, let us know how it works for you.

Range extender compatable with Westell 7500

I want to extend my DSL wireless to my garage/shop, about 150 feet from the house where my Westell 7500 router is located. In doing a search I saw that a Verizon rep recommended the Linksys Range Expander, WRE54G. However, there was no mention of the wireless router being used. Is that expander compatable with the Westell 7500 or is there another alternative that will work so I can use my laptop in the shop?

Just spoke with Linksys tech support and they said 'no' to a G range extender with an N network. (I have WRT150N router and WUSB300 adapter.) Wanted to boost the signal, but they said the router already has a built-in range extender and the WRE54G wouldn't help.

Using a Range Extender with WLC & LWAP

Similar Messages

Maybe you are looking for