Using Airport Express and Intenet at same time

I have set up an Airport Express to play music from my Mac in another room. Works fine. But when I am doing that, I cannot use the internet on the Mac. This is because the wireless symbol on the title bar gives me two choices -- my wireless network or the Airport Express. Is this normal or is there something I can do to have both working at once. Ta in advance

the_gauntlett, Welcome to the discussion area!
You need to reconfigure the AirPort Express (AX) so that it joins a wireless network and select your current wireless network.

Similar Messages

I have a linksys WRT54G router that we use as a base. I want to use Airplay using Airport Express and hook up my stereo to it. How can i set up my Airport express without a PC/laptop? I just downloaded Airport utility on my iphone and ipad,will that work?

I have a linksys WRT54G router that we use as a base. I want to use Airplay using Airport Express and hook up my stereo to it. How can i set up my Airport express without a PC/laptop? I just downloaded Airport utility on my iphone and ipad,will that work? And one more thing about the setup, the linksys router shich acts as a base is in a different room as the airport express which i wanted to use for airplay. So I'm hoping to hook up the Airport express via wireless signal. If i can set it up, can someone pls help me out by posting detailed instructions. Thanks so much!

The first message that AirPort Utility will display during the auto setup will be that the Express will be confgured to "extend" the network. When AirPort Utility analyzes the network further, and sees that the Express cannot "extend" the 3rd party network, the next message will indicate that the Express is being configured to "join" the wireless network.
Once the Express is configured, if you later go into AirPort Utility to check the settings under the Wireless tab, you will see that the Wireless Mode is indeed "Join a wireless network".

Lost connection to one of my Airport express units. Serial number 44500WQV0. Message in Airport Utility is to use Version 5.6 to configure base station. I have version 6.3.1. Both airport express units bought at same time few years ago.

Hello all.
Lost my connection to one of two airport express units. Both purchased few years ago. Use them to stream music to house speakers via WiFi. I have v6.3.1 of Airport Utility. Message says to use v5.6 to reconfigure this base station.
How do I do that, please?
Mahesh

You can use the following workaround to install AirPort Utility 5.6 on a Lion or Mountain Lion Mac:
Be sure to read the caveats at the end.
Lion / Mountain Lion's package installer will refuse to install superseded versions of AirPort Utility. Instead you will need to use a package extractor such as Pacifist or unpkg. Pacifist is shareware, unpkg is free.
Download Pacifist here: http://www.charlessoft.com/
Download unpkg here: http://www.timdoug.com/unpkg/
Download AirPort Utility 5.6 here: http://support.apple.com/kb/DL1482
When the AirPort Utility .dmg file finishes downloading, open it to expand and reveal the AirPortUtility56.pkg package installer file.
Directions for Pacifist (I do not have screenshots for unpkg but the idea is similar):
Open Pacifist and from its File menu, navigate to the package and open it.
Click the "reveal triangles" until you see AirPort Utility 5.6.app:
Select it and then click Install from Pacifist's toolbar. It will then be installed in your Utilities folder, and you can quit Pacifist.
The most recent version of AirPort Utility included with Mountain Lion should be used to configure 802.11n - capable AirPort Base Stations. Make no attempt to delete it. It and the older version (which will bear the unique name "AirPort Utility 5.6") can peacefully coexist. Use the older version only as necessary for older AirPort Base Stations that cannot be administered any other way.
If you happen to have an archived copy of the AU 5.6 app somewhere, such as a Time Machine backup or equivalent, you can simply restore it or drag the app to your Mountain Lion system's Utilities folder instead of resorting to the above procedure. It will run without complaint. It is only the package installer that is the problem.
Keep in mind that Apple's decision to abandon support for the original AirPort Express and AEBS was for reasons known only to them. Remember that you are using obsolete equipment, should some future OS X feature not work for you.

Ethernet Internet & Airport Express Printing at the same time

Ok Guys:
My 18 year old cousin is going off to University this fall, and she will be taking her iMac G5 and a new Macbook with her. She wants to set up her canon printer wirelessly by using an Airport Express. Assuming her Internet access is by ethernet, provided in each residence room by the university, can she also setup an Airport Express to use for wireless printing at the same time? In other words will the following scenario work?
Network 1: Ethernet Internet (provided by the University)
AND (at the same time)
Network 2 : Wireless printing network by Airport Export Express.
Thanks.
-Robert
--Please Include As Detailed System Info As You Can With Your Questions!-- Mac OS X (10.4.9) PM Quad 8.5GB 7800GT 30"; MBP 17 2.33 C2D 3GB My 1st Computer was an Apple IIc!

She can configure the AirPort Express (AX) with the option to distribute IP addresses DISABLED.
Then she can connect the AX directly to the Ethernet connection in the room.

Help - Receive message "an error occurred printing this document" when using airport express and Ipad

Hi, I am trying to set up an airport express hub to work with a Star tsp100 receipt printer and IPad 2. The IPad is being used to accept credit card payments and I was hoping to print receipts out wirelessly using the airport express and receipt printer. I checked to make sure the airport express has the latest firmware and it does. The IPad software is also updated to the latest 7.1. I then connected the Airport express and IPad and the network setup with no problems. I connected the receipt printer to the airport express using the USB slot available. While the printer comes up as available, when I attempt to print something, I get the error message "An error occurred printing this document" and I can cancel or Try again. No matter how many times I try, I continue to get this message and I lost as to the cause. When I disconnect and reconnect, another instance of the printer appears, but receive the same cryptic error message when I try to print. Totally lost, please help

Hi kelston3,
In order to print from an iPad you will need to use a printer that is compatible with AirPrint, which is described in the following article -
About AirPrint
http://support.apple.com/kb/HT4356
AirPrint printers must be wireless on your network - not connected via USB to the base station. There is a list of printers that are known to be compatible with AirPrint in the article.
Thanks for using Apple Support Communities.
Best,
Brett L

Airport modem and itunes streamed same time

Is it possible to be online with my wireless connection through (via a Netgear router) and at the same time to stream Itunes to airport express? Currently, my mac G4 asks me to choose one or other of the connections.

You must configure the Express to be a client on the Netgear's wireless network. You can use the Airport Setup Assistant to accomplish this. Make sure you do not specify that you want to extend the range of the wireless network: the Netgear router is incapable of supporting that feature.

I used Airport Base station and I was able to extend my network using airport express and connect my printers. Now I am using Extreme and I can't extend the network (Express) or the printers nothing shows up. I am using utility 6.3 and Mt Lion What is

I had an Aiport Base Station and extended using Airport Express, where I also connected my printers (network). Now using Airport Extreme off Mt Lion 10.8.4 and Utility 6.3.
I can't extend the network (express) or connect my printers (USB) nor will it find my one wifi printer.
What's up?

For now, leave the AirPort Express powered off.
Power off the entire network....all devices.....in any order that you want
Wait a few minutes
Power up the modem first, and let it run 2-3 minutes by itself
Power up the AirPort Extreme next, and let it run a full minute
Keep powering up devices one at a time about a minute apart until everything is powered up (leave the Express off for now)
Open AirPort Utility and check to see if the AirPort Extreme is visible.
If it's not, click the AirPort Utility menu at the upper left of the screen, then click About AirPort Utility. Post back with the version number of AirPort Utility that you see there....which should be AirPort Utility 5.6.1.
Post back on your progress.

Streaming 3d movies to my Samsung 3DTV using AirPort express and a wireless LAN adapter has not worked. What is my cheapest option for making this happen?

I need a transfer rate minimum of 9mbps. My AirPort express and 3DTV are on different floors, so I cannot directly connect with an ethernet cable. Can I buy an older AirPort express, use it as a bridge, and connect my TV to it via an ethernet cable?

Hi rockchalker,
Thanks for using Apple Support Communities.
For 802.11n Wi-Fi base stations, creating a roaming network is by far the best choice. This will provide the best throughput between the base stations and your Wi-Fi devices.
If you are unable to build the recommended Roaming network, then a Wirelessly Extended Network is the next best option.
For more information on this, take a look at this article:
Wi-Fi base stations: Extending the range of your wireless network by adding additional Wi-Fi base stations
http://support.apple.com/kb/HT4145
Hope this helps,
Mario

How do I set up my Airport Express and not interrupt my TIme Capsule

I have ATT UVerse recently installed and have my Time Capsule Router Behind their installed router. I recently purchased Airport Extreme and want to install it as well so I can connect an older Version of a Sony PS3 which doesn't have bluetooth capability via rj45 since the time capsule is no where close to my PS3. Is there a way to install this Airport Express and not mess up the settings of the Time Capsule?

Hello hbwilli. Welcome to the Apple Discussions!
I recently purchased Airport Extreme and want to install it as well so I can connect an older Version of a Sony PS3 which doesn't have bluetooth capability via rj45 since the time capsule is no where close to my PS3. Is there a way to install this Airport Express and not mess up the settings of the Time Capsule?
Yes. You will want to configure the new 802.11n AirPort Express Base Station (AXn) as a ProxySTA. In this configuration, the AXn will join the wireless network created by the Time Capsule and share Internet access through its Ethernet port to the PS3.
To activate ProxySTA, you must set up the Express to join a wireless network and then enable the Allow Ethernet Clients setting; both settings are located in the Wireless tab of AirPort Utility. The feature should work with any wireless network: a, b, g, or n; and 5GHz or 2.4GHz. (Note that the Express, which ships with firmware 7.3, must also be updated to firmware 7.3.1 for this feature to appear.)

Using Airport Express and music sounds distorted.....

I just hooked up my airport express to my whole house stereo and the music sounds distorted. I've adjusted the volume on the amplifier, the room volume control and the computer volume control.....and it still sounds distorted. Any ideas on what I can do?

Temporarily, plug a pair of headphones into the AirPort Express and check the sound quality. It is OK, you know that everything is working through the AirPort Express.
Often the audio plug will make poor contact with the audio jack on the Express which can cause a hum or intermiitent audio signal. Wiggle the plug around to see if this might be the case. You may need to try another audio cable.
Make sure that you are not plugging into a PHONO input on the amplifier. You would want to use AUX or CD or even TAPE would work if you have an older amplifier/receiver.

Using Airport Express and Extreme Together

I have the old Airport Express and have just bought the latest Extreme. I'm sure Extreme will work fine with my iMac but am not so sure it will work with my G4 Powerbook as it does not have the recommended software requirements. Is there anyway I can setup a network using both the old Express and the new Extreme?

Welcome to the discussions!
Your old AirPort Express is a "g" wireless device while your new AirPort Extreme is a newer and much faster "n" wireless device.
If you are asking if you can use your old AirPort Express to "extend" the wireless from the AirPort Extreme using wireless only, the answer is yes....BUT....your new AirPort Extreme will drop down to old "g" wireless levels if you do this.
The setup procedure for this is quite difficult and frustrating for many users. To get an idea of what is involved if you want to try this, see this link for the procedure:
http://discussions.apple.com/thread.jspa?threadID=2355832&tstart=0
IF...you are able to connect the AirPort Express to your AirPort Extreme using an ethernet connection, the setup will be much easier to accomplish and your AirPort Extreme will maintain faster "n" speeds on the wireless. Post back for more details if that is a possibility.

I would like to set up a media server on time capsule using airport express and an ipad as a remote for dance studio

I am wanting to set up a network for my business and was hoping if someone could tell me how to do this and if it will indeed work. Or if you have any better ideas.
I want to transfer all music to Airport Time Capsule. I want to plug in the aiport express to my sound system. I want to access music through the ipad off the timecapsule to play it without downlaoding it on the ipad.
We currently use Icloud, but there is too much music and too many devices accessing for it to work effectively. I am running a dance studio so we need more music than what could ever be stored on an ipad/ipod.
As an extention to this, can we use multiple Airport expresses plugged into mutiple sound systems to simultaneously access different music from the same time capsule?
Any ideas would be so great!

The answer is not if you use iTunes.
The TC is NOT an iTunes server.. it is not a media device at all. It is a backup location for Time Machine.
You need a computer in the network which stores the iTunes library and you can then play it via the ipad.
A mini with a large USB drive plugged in will work fine.. it doesn't need to be new.. a couple of years old mini will work just as well.
As an extention to this, can we use multiple Airport expresses plugged into mutiple sound systems to simultaneously access different music from the same time capsule?
I am not sure.. there will be network limitations to this.
Look up how to use itunes in a network.
http://support.apple.com/kb/ht4620
You would do better perhaps posting the question in iTunes section.. if as I guess you are actually using iTunes.

Use Airport Express as Internet hub, bridge Time Capsule for N-only?

OK I checked on the forums, but I could not find anything quite specific it what I was trying to accomplish.
I recently got a 500GB Time Capsule. I changed my network around, which was based off of two Airport Express stations – on in the office hooked up to internet & printer, one in living room hooked up to sound system – and made the TC the main hub, connecting modem to it's WAN port and bridging the office AX via LAN port in bridged mode, sharing the living room AX as WDS. This way, I had the TC in N-only mode in 5ghz spectrum using wide channels for fastest performance. All this worked well.
Except that I noticed that with the TC in the office – where the laptops rarely are – my data transfer speeds were no better than .11g speeds. So I mucked around a little, and noticed that it really was just the case that the separation of distance & obstruction was slowing the transfer speeds over .11n-only that much!
Well, it occurred to me that there may be another way. What I had intended to do was to hook up the modem back to the office AX, move the TC to the living room where it'd be "line of sight" to the laptops most of the time, and bridge the TC and living room AX over LAN. So the idea was to keep the networks separate wirelessly still, and have the internet "bridged" wirelessly from the office AX to the living room AX and then over LAN to the TC. The thinking was that the hit on the internet connection would not be noticeable as the threshold for that is well below the streaming capabilities of the AX network still, so I'd not lose anything there, but gain MUCH faster speeds with the TC in line-of-sight of the Laptops (3x as much in testing; with TC in office and laptops in living room, 1.3gb folder took 9 minutes, same folder line-of-sight testing took only 3 minutes).
However, I CANNOT get this to work properly. I thought I really just needed to move the TC to the living room and bridge it there, as the services should be shared over the LAN port since the 2.4ghz AX are in "bridged" mode, but that didn't work. I kinda-sorta got it to work by forcing both the AX network AND the TC network into "bridged mode," but that didn't seem right or wise, so I tried some other settings, putting the TC to bridged and having the office AX distribute IP addresses, but then it wouldn't show up under restart, and I'm just confused now on how to set that up!
What i need is: To have the "Office AX" hooked up to the modem & printer, on 2.4ghz since it's the older .11g model, with the "Living Room AX" on that same network. Then the TC in 5ghz N-only bridged to the Living Room AX via LAN, so it can share the services (internet & airtunes) and still get high data transfer speeds to the laptops via the advantage of Line-of-sight, non-obstructed networking.
How do I need to set this up? It's possible, right?
Message was edited by: Anthony Caltabiano

OK while I was working out this morning, I was trying to think of WHY my setup wasn't working. I had an epiphany, and decided to try once more. This time, it worked.
The problem was that originally I had the Living Room AX set up as a Remote, so it was hooking INTO the network, not extending it. I know that with that setup you can't hook up to THAT station and get internet or anything, you hook into the MAIN station and you can SEE the remote's services that are "plugged in" to it.
I didn't think this would be an issue with the TC physically attached to the ethernet port, but apparently this behavior extends to the ethernet port on remote stations for internet access... I had a feeling that MIGHT be it, so I started from scratch, and this time set up the Living Room AX to extend the network instead of just joining it. Then hooking up the TC to the Living Room AX's ethernet port and selecting "Bridge Mode" on the TC got me the good ol' green light!
So, if anyone out there is trying to build a dual-band network, with their TC on .11n-only and bridge to services supplied by a 2.4ghz network, AND route their internet access through the 2.4ghz network instead of the TC so that they can keep their TC more centrally located for better performance... make sure you do it like this: Set up the alternate (2.4ghz) network as relays, "extending" the network, so that when you plug into it, the TC essentially thinks it's plugged directly into the main router, no matter where it is. The throughput hit for internet access over WDS shouldn't be a problem for US-based peeps, as our speeds are typically well below the .11g threshold anyway.
I also found that it helped to NOT hide the SSID of the 2.4ghz network; doing that kept rendering failed attempts to force the secondary AX to join as WDS. Once I redid it without hiding the SSID, all went well.

Airport:PS3 and Mac at same time?

I'm looking at getting an airport express or extreme whichever will be enough for my needs. This is actually going to be my first router, here are what I'm looking for it to do for me:
rue
1) I am only getting this to be able to connect my PS3 to the Internet wirelessly, my computer doesn't need to be wireless at all.
2) I need to know if I can use both the PS3 and the iMac on the Internet at the same time?
3) and finally which of the airports is going to be good for me? The PS3 is about 25 ft away in the next room and I would prefer keeping my iMac connected to cable modem if that is possible, any help would be great thanks

1) I am only getting this to be able to connect my PS3 to the Internet wirelessly, my computer doesn't need to be wireless at all.
To support both wired and wireless clients, you will want the AirPort Extreme.
2) I need to know if I can use both the PS3 and the iMac on the Internet at the same time?
Yes, both can be used simultaneously with either AirPort.
3) and finally which of the airports is going to be good for me? The PS3 is about 25 ft away in the next room and I would prefer keeping my iMac connected to cable modem if that is possible, any help would be great thanks
You will need the AirPort Extreme. You would not be able to keep the iMac connected to the cable modem. Instead, you would connect the AirPort Extreme to the modem, and then, both the iMac and PS3 to the Extreme.

Itunes remote speaker using Airport Express and Extreme

I have purchased an Airport Extreme and Airport Express, so I can listen Itunes music on my stereo system. For some reason, there is simply no remote speaker selection button on the bottom right of the Itunes windows. Does it has to do with the fact that I am using an old Mac OS X?
My Macmini has no airport card, so I connected the ethernet to the Airport extreme, and plugged the Airport express few feet from the base. Nothing but an orange tilting light comes out of the little box. I can surf the net perfectly but the Itunes is ignoring all my investment on the couple of Airport boxes i purchase...What I am doing wrong?

Yes, I thought that purchasing the Airport extreme as
the ethernet interfase directly connected to the
MacMini, was almost the same as having the airport
card inside the Mini. Where did I get lost?? I have
the extreme directly to the mini, and an express
plugged somewhere close and nothing happens...
The problem is that the mini can only stream iTunes to an Airport Express via Airport. While you have connected it to an Airport basestation, as far as the mini is concerned, it is working via ethernet because that's how the data is leaving the system. It doesn't have an Airport card, thus it can't stream iTunes content to an Airport Express.

Using Airport Express and Intenet at same time

Similar Messages

Maybe you are looking for