Using Airport Express to bring up the speed of wireless to n with a/b/g devices
I have an old computer my wife will not give up for whatever reason. It's slowing the entire household network down with it's a/b/g card. I turned off her wifi and used a cat 5e cable to connect to the Airport Express set to extend a signal. I've found my wireless works MUCH faster. I hope this helps you!
Yes, I kind of thought that but didn't know why.
Could you explain 'cause I'm trying very hard to
understand Networks.
An Airport Express can be configured to extend a wireless network wirelessly using WDS (wireless distribution system) which effectively receives the signal from a main base station and broadcasts it again.
You can only use an Airport Express in this way with a main base station which supports Apple's implementation of WDS.
You can do this with
- another Airport Express
- an Airport Extreme Base Station
- a Linksys WRT54G or WRT54GS (not v5)
- a Belkin Belkin F5D7230-4 and F5D7231
- one specific model from SMC (can't find model number right now)
- one specific model from Buffalo
For wireless routers not on this short list - not possible.
In particular, it will not work with any WiFi routers from D-Link or Netgear.
Also, can you suggest an
alternative?
You have two options.
Purchase an Apple main base station (and sell the D-Link)
Connect the Airport Express to the D-Link by cable and extend the network in that way (known as a roaming network).
iFelix
Similar Messages
-
I bought an airport express and was told that I can configure it, and then move it to the G5 and connect it with the ethernet cable giving the G5 access to the network. But the laptop I first configure it to loses the connection once I remove the ethernet cable between the airport express and the modem. When I connect the G5 to the airport express nothing happens. Any ideas?
Hello Ed,
Is this how you set it up?
http://www.apple.com/airport-express/
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.5, 10.6, 10.7 & 10.8…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x/10.8.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
10.4 instructions...
Is that Interface dragged to the top of Network>Show:>Network Port Configurations.
If using Wifi/Airport...
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed. -
Use Airport Express Brick N to extend network via ethernet
I have the old brick-style Airport Express N model, which I'm currently using to extend the newer Airport Express hockey puck. The hockey puck is setup to with DHCP and creating the network. The brick is in setup to extend the network using DHCP and in Bridge Mode. When I plugin the Ethernet cable from the Ethernet port of the hockey puck to the brick, I lose all internet connectivity. I seem to recall reading some documentation that said the brick would support ethernet rather than just over-the-air. Thanks for your help!
My question is: can I connect the two via ethernet cable to the extending is happening over the air? I'm not sure the brick is capable of this?
It is possible to "extend" in two different ways:
1) Extend using a wireless connection between the AirPorts. Apple calls this "extend using wireless" during the setup. When you extend this way, about half of the potential speed on the network is lost.
2) Extend using a wired Ethernet connection between the AirPorts. Apple calls this "extend using Ethernet" during the setup. When you extend this way, full bandwidth on the network is maintained since there is no signal loss in a wire.
If you want to "extend using Ethernet", the 2nd Gen AirPort Express must be the "main" router, so you will need to reconfigure it for that purpose. The 1st Gen will also need to be reset back to default settings and reconfigured as well.
Once the 2nd Gen Express is working correctly as the main router, connect an Ethernet cable from the LAN <--> port on the 2nd Gen Express to the Ethernet port on the 1st Gen Express and use AirPort Utility for the setup. -
I have a MacPro 2008 workstation. It has no Airport/Airport card so I have to use an ethernetcable to connect to my modem. As the MAcpro
is in my office in the attic and the wireless modem is in the basement I have a problem. I wonder if it is possible to use Airport Express to connect to the wireless network? Itshould be like this: in my office I connect the MacPro with AE through an ethernet cable. If I can then get AE to connect (wireless...) to my wireless network I should be ablle to connect my MacPro to internet/wireless network. Is this possible???? Any suggestions are very much appriciated. Thank you.Apple calls this configuration a ProxySTA.
To activate ProxySTA, you must set up the Express to join a wireless network and then enable the Allow Ethernet Clients setting; both settings are located in the Wireless tab of AirPort Utility. -
Can't use Airport Express after upgrading to Leopard
I use Airport Express for wireless printing and AirTunes via powered speakers/hifi. It was working very reliably until I upgraded to Leopard. Now, I am unable to use Airport Express. I get the blinking orange light, but when I scan with Airport Utility, Airport Express is not detected. Manual setup is grayed out, so I can't set it up at all. I am using Airport Utility Version 5.2.2 (522.3), and there does not seem to be any updates or patches to apply at the moment. I have tried on my iMac G5 and MacBook, with the same result on both computers.
I am also reading that many others are having problems with Airport Express after upgrading to Leopard, perhaps not with my specific hardware configuration, but this is very disappointing.
I am open to suggestions to try a few things to get it working, so any help is appreciated.
Message was edited by: a jFrom the Mail menu, select "Preferences". Hit the Accounts tab. Select the Account. Under Account Information, reapply the user name and password.
Check with the provider if the account needs authentication. This is in the Advanced tab. Usually just a repeat of user name and password. -
Hi I am not sure ! Ask can use airport express join pc ?
Hello I am deaf ! My use apple . My friend. Said me can use airport express join PC ?
The AirPort Express is a wireless router. You can use it in a number of ways, including providing a wireless network that a PC can join.
-
How to set up Airport Express to extend Buffalo WHR HP 54g wireless router
Contrary to what official Apple policy is, it is possible to use Airport Express as a remote repeater using a Buffalo router.
I sent hours setting up this network and wish to share what I learned
I only wanted to use the Airport Express as a repeater to distribute the internet to the far reaches of the house--no iTunes, no Printer, and I did not bother setting security. If you want to add any of those features please make sure that the basic setup is working as described below. I have no idea how to successfully set up these features. My advice is to search the internet for guidance.
Anyway: how to set up the Buffalo wireless access router to work with Airport Express
Setting up the Buffalo:
From the routers home page of 192.168.11.1, hit the "advanced" box at the top
1. Go the "Wireless config" "basic" item. Give name to your network (spaces are allowed), lets call it "WIRENAME" and select wireless channel 1 or 6 or 11. These channels have the least interference and will tend to work when the others do not.
2. Go the the "repeater" item under Wireless config. . " Enable" repeater/bridge (WDS). Next register the MAC address of the Airport Express. Record both the LAN and Wireless MAC addresses.
That is about it. Your Buffalo system Info page should look like this
Model
WHR-HP-G54 Ver.1.40 (1.0.37-1.08-1.04)
AirStation Name AP001D73DEB2D6 Operational Mode Router Mode WAN
DHCP
Connection Status
Communicating
Operation
IP Address
myinfo
Subnet Mask
255.255.255.248
Default Gateway
my info(Via DHCP)
DNS1(Primary)
my info (Via DHCP)
DNS2(Secondary)
my info (Via DHCP)
Host Name
my info (Manual Setup)
Domain Name
earthlink.net (Via DHCP)
MTU Size
1500
DHCP Server Address
10.108.48.1
Lease Acquired Time
2006/01/04 12:03:15
Lease Period
2006/01/05 12:03:15
Wired Link
100Base-TX (Full-duplex)
MAC Address
00:1D:73:xx:xx:xx
LAN
IP Address
192.168.11.1
Subnet Mask
255.255.255.0
DHCP Server
Enabled
MAC Address
your address recorded in the repeater tab
Wireless(802.11g)
Wireless Status
Enabled
SSID
WIRENAME
Encryption Mode
Not Configured
Wireless Channel
11Channel (Manual)
125* High Speed Mode
Disabled
MAC Address
your address recorded in the repeater tab
For the Airport express: here is a summary of what the settings are: Start Airport Express Utility and when it comes up
Select "Manual" setup
On the Base station tab: Give Airport Express a name, any name and any password. Do not select the box: Allow setup over the internet with Bonjour
On the wireless tab: Wireless mode: Participate in a WDS network
Network name: the name you gave in the Buffalo router: EG: WIRENAME
Radio mode: 802.11n(802.11b/g compatible)
Channel : the same as you set in the Buffalo
Wireless security: None
WDS tab: WDS mode: WDS remote
Check: allow wireless clients
WDS main: the MAC address of the wireless (not LAN) side of the Buffalo router
Access control tab: MAC address access control: Not enabled
At the top of the control box , click on the Internet icon
Internet connection: Connection sharing: Off (Bridge Mode)
TCP/IP: Configure iPV4 : Using DHCP
I put in the address of the DNS servers listed on the Buffalo System info page above.
At the top of the control box Music Icon: I did not enable AirTunes
Printer icon: did not set this up
Advanced icon: leave every thing alone
That is it. Just do everything as above and your Airport Express will act as a repeater. (And save yourself a couple of days struggle.)
PhilMany thanks for the info.
In case you were not aware,the following list of Apple WDS compatible devices has appeared on numerous sites and in numerous Internet links and articles regarding this subject:
3com OfficeConnect ADSL Wireless 11g Firewall Router model 3crwdr100a-72 but ONLY with NO encryption
Belkin F5D7230-4 and F5D7231
BT Voyager 2091 or 2100
Buffalo WGR-G54
Linksys WRT54G or WRT54GS (though v4)
Netgear WGR614 v6 -
I can't print wirelessly using Airport Express. I have my HP printer connected to a USB hub, and the hub to the Airport Express, but when I select the HP from the printer list, my MacBook says the printer is "off-line" - even when it is not. I've tried several USB connectors, and several different ports on my USB hub; same result. I need to have the HP connected to the hub 'cause from there it's connected to our desktop Mac.
Hi,
I am currently replying to this as it shows in the iChat Community.
I have asked the Hosts to move it to Snow Leopard (you should not lose contact with it through any email links you get)
I also don't do Wirelss printing so I can't actaully help either.
10:01 PM Friday; July 29, 2011
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
G4/1GhzDual MDD (Leopard 10.5.8)
MacBookPro 2Gb( 10.6.8)
Mac OS X (10.6.8),
"Limit the Logs to the Bits above Binary Images." No, Seriously -
How can I use my Ipad in a hotel that only has ethernet connections? The Apple store clerk told me that travel express won't work in my hotel unless I also have a computer.
The issue with the Airport Express (or any of the Apple routers) is that you need the Airport Utility to configure it. Airport Utility works on OSX and Windows, but not on the iPad (or iPhone or iPod Touch.) It will work, if you can preconfigure the Airport correctly ahead of time, but you'd be stuck if you did need to reconfigure while at the hotel.
You can use most any other router that is configured with a web page, which means you have a chance of configuring with Safari on the iPad. If you want something somewhat portable, I use a "travel router" made by D-Link. The current model is the DAP-1350. Other companies make similar travel routers, but I have no experience with the others. -
I can print from my macbook pro using airport express usb connected printer, however my iPad and iphone are looking for an airprint printer. Can I direct the iPad/iphone to the usb connected printer. Macbook iphone and iPad confirm a wifi connection through the airport express.
You will need to install an App like Print Central on the iPad to try to print to the printer. It will allow you to print to most printers. Check with their support folks if you need more info.
PrintCentral for iPad on the iTunes App Store -
Why cant i print from my ipad using airport express but i can print from my mac using the express
why cant i print from my ipad using airport express but i can print from my mac using the express
Because your printer has to be Airprint compatible and connected to WiFi. There are applications, such as Printopia, that will allow you to print through your computer.
-
After I started using Airport Express, I get the message " host '192.168.0.4' is busy" andmy HP [ethernet] printer no longer works.
OK, I found this thread which answered my question.
http://discussions.apple.com/thread.jspa?messageID=610763򕇋 -
I want to use AirPort Express when I am traveling. I would like to use a wired internet connection in a hotel room to create a wireless connection. However, I do not normally carry my laptop, just my iPad. Is it possible to do this?
You will have to pre-configure the Express using AirPort Utility on your computer before you leave on the trip. The Express will store and remember the settings.
You might want to check with the hotel in advance to make sure that they have Ethernet ports available. Most hotels have switched to wireless and the others are not far behind. -
I currently have a D-Link DI-604 broadband router with windows computers. How can I add wifi to the network for use with ipad? Can I use AirPort Express?
Yes. You can directly connect an 802.11n AirPort Express Base Station (AXn) using an Ethernet cable. The AXn would then just need to be configured as a bridge to allow the D-Link to continue to provide both NAT & DHCP services for all network clients connected to either router.
In this configuration, the AXn would broadcast a wireless network for your wireless network clients to connect to. -
Can I use a 2nd Airport Express to bring internet to a wired-only desktop?
Hi.
I have an Airport Express that's working flawlessly as a wireless router via a cable modem. Problem is, I have a second computer ( a desktop PC) that's too far away from the cable modem to hook it up via the ethernet. Is it possible to use a second Airport Express to extend the wireless network and thereby connect to my desktop with the ethernet cord? I guess this would be kind of using the AE backwards. If this is possible, could you please tell me how I might do it?
Thanks so much!Here are the basic steps in setting up a WDS:
(Note: To facilitate the WDS set up, place the base stations within near proximity of each other during the set up phase, and then relocate them to their desired locations when complete. Also, jot down the AirPort IDs (not the Ethernet ID) for each of the base stations to be used in the WDS. The AirPort ID and is printed on the label on the bottom/side of the base station.
I suggest that you also perform a "factory default" reset on each of your AXs to get them to their original "out-of-the-box" configuration.
Finally, for this WDS, AX#1 (the AX connected to the Internet modem) will be the main base station, and AX#2 will be the remote base station.)
Main Base Station Setup - AX#1
o On your MacBook Pro (MBP) click the AirPort status menu in the menu bar and choose the wireless network created by AX#1.
o Open AirPort Utility (located in the /Applications/Utilities folder).
o Select AX#1, and then, choose Manual Setup from the Base Station menu.
o Click Wireless in the toolbar, and then, choose “Participate in a WDS network” from the Wireless Mode pop-up menu.
o Click WDS, and then, choose “WDS main” from the WDS Mode pop-up menu.
o Select the “Allow wireless clients” checkbox.
o Click the Add "+" button, and then, enter the AirPort ID of AX#2.
o Click Update to send the new settings to the base stations in the WDS.
Remote Base Station Setup - AX#2
o On the MBP click the AirPort status menu in the menu bar, and then, choose the wireless network created by AX#2.
o Open AirPort Utility if not already running.
o Select AX#2, and then, choose Manual Setup from the Base Station menu.
o Click AirPort in the toolbar and click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and then, choose the same channel as the main base station from the Channel pop-up menu.
o Click WDS, and then, choose “WDS remote” from the pop-up menu.
o Enter the AirPort ID of AX#1.
o Click Update to transfer the settings to the base station.
(ref: Pages 42-46 of "Designing AirPort Networks.)
Maybe you are looking for
-
Invalid column name 'SKEY_VAL' Error when Populating a planning dimension
I'm trying to populate a planning dimension from a view in MSSQL. I thought that I had mapped the all of the required columns in my interface in ODI, but I am getting the following error: 207 : S0001 : com.microsoft.sqlserver.jdbc.SQLServerException:
-
Please excuse my basic question: 1. Can you put videos on the websites on iWeb and if so how large can they be? 2. I have a small business and think a iWeb may be low-maintanence enough to set something up on. Do people use iWeb for this or is it gen
-
I don't even know if I'm posting on the right site. I went to compaq.com, but got forwarded to hp.com. My husband bought me the compaq presario cq60-206US Notebook in Feb, 2009. I have not been happy with it at all. This computer gets extremely ho
-
Implementing repository manager
I implemented a custom repositry manager, which read xml file from a backend system (db). But i couldn't see the items which ist trasformed into unified aspects. May be i make mistakes in code. Have you any suggestion and sample code. Thanks for any
-
I want my Iphone5s to be replaced. Will it be on the spot?
I bought my Iphone5s 08 Dec 2013 from an ordinary store in the Mall, in Qatar It was heating up a lot, which I did not experience with my iphone4s for two years. When I am charging it, I can feel a tingling shock. When I docked it, I can hear humming