Using Airport Extreme Base Station with Cable Modem

Hi everyone,
I have just bought an Airport Extreme Base Station. I connected it to my cable modem (Surfboard 3100) through the WAN port and my iMac G4 is connected to it through the Ethernet port. Installed the Airport Utility, and configured the base station with the normal settings of DHCP for Internet and DHCP for internal network.
After restarting the base station, my Internet connection from the iMac through the base station is very slow and most of the time will time-out. My Internet connection through my PowerBook G4 using wireless through the base station is ok though.
My question is, is there some setting which I should set for the Ethernet portion of the base station to make my wired connections to the Internet work?
Thanks in advance for any help!
regards,
Weiming
iMac G4 Mac OS X (10.4.10)

Hi,
My iMac G4 does not have an Airport card. I did not physically restarted the base station, its part of the sequence when we update the configuration, that the base station will restart on its own.
regards,
Weiming

Similar Messages

Trouble using Airport Express Base Station with DSL modem, Router and Hub

About 18 months ago, I had an Airport (802.11b) with WAN & LAN ports and modem hooked up to support two laptops, a Titanium Powerbook G4/600 and G3/400. The setup went from DSL modem -> Linksys router -> to Airport -> Hub (which had desktop and ethernet laser printer plugged in). The network worked fine.
Then, I got a G4 iBook to replace G3/400. Wanted to get 802.11g to support “g” Airport card in iBook. Got a Linksys 802.11g Wi-Fi with 4-port router for $50. Hooked it up directly with DSL modem. (Couldn’t get it to send out to hub). Hooked the desktop and ethernet laser printer into Linksys Wi-Fi/router. The only way I could use the printer was by having it be a shared printer from the desktop. This was often problematic.
Two months ago, I got a refurbished Airport Extreme Base Station. I can’t get the AEBS to interface directly with the DSL modem, so I hooked it up as follows:
DSL modem -> Linksys router -> to AEBS -> Hub. I plugged my Epson 820 (USB) into the AEBS and can see it to print to.
I have a static IP. That info is entered into Linksys router. Router set as Gateway, with DHCP enabled. AEBS is set to Connect using Ethernet, Configure using DHCP. Network setting: Distribute IP Addresses is unchecked.
Here’s my issue:
I can’t see the ethernet laser printer. It will occasionally flash available, but is gone in less than a minute. The printer is HP 2100 series.
Sometimes I can connect to the desktop G4 tower; most times I can’t.
I have checked and double-checked the cables.
Both the printer and desktop are connected to the Hub.
What can I do so that I can see the HP 2100 series printer and the G4 tower?

Don,
Thanks for the suggestions. Glutton for punishment that I am, I tried this again, “just for grins.“ The six other times I tried this, I couldn’t get the AEBS to “see” the Internet. And lo, this time it worked. Here’s the setup now:
DSL modem -> AEBS -> 4-port hub (which is connected to G4 tower and HP 2100 Ethernet printer). My USB Epson is connected to the AEBS, and I can print from the laptops. AEBS is set up: manual IP info, Network: distribute IP address; share a single IP using DHCP.
When I still couldn’t see the desktop G4 and the Ethernet HP 2100 connected via the hub (not), I got a flash. I had swapped out the cable a number of times to no avail. Then I realized, the hub is old and all the cables I was using are the new CAT5s. I dug out an old four-wire with RJ45 connectors that my husband made years ago (probably a cross-over cable). It was quite an effort as the cable is 30 ft. long and wrapped around the perimeter of the office behind desks and file cabinets, entwined with all the other wires. But I plugged it in and, Shazam! I am WORKING!
And, Don, thanks to you, I have eliminated the router from my gaggle of electronic boxes.

Using Airport Extreme Base Station with a Switch

Thanks in advance for your help, this has been driving me crazy.
Here's the setup I'm trying to make work but without success:
Cable modem -> AEBS -> Switch -> ethernet cables -> devices (TV / Roku / ethernet wall plates, etc.)
Hardware:
- Cable modem is ARRIS / Motorola SurfBoard SB6183 - pure modem I believe, no router capability
- AEBS is latest version new in Sep 2014
- switch is TP-Link 16 port gigabit desktop/rackmount switch model TL-SG1016D
Wireless from the AEBS works, but I'm not able to get any signal from anything connected to the switch. I'm using the bottom ethernet port on the AEBS to connect to the modem.
Is this 1) a configuration issue with AEBS, and since it's a router I can use it in between the modem and switch, just need to change settings on the Airport, or
2) a setup issue, and I need to get a proper ethernet router and slot it into the setup somehow...
3) some other issue
Again, much appreciate your help,
Dan

The setup that you mention is correct.
We assume that you have another Ethernet cable connecting from one of the LAN <--> ports on the AirPort Extreme to the switch.
Temporarily, disconnect the Ethernet cable that is connected to the switch and instead, connect it to another device.....like a computer.....to see if you can get a good Internet connection that way. Be sure to turn off the wireless for this "test".
If you cannot get a good connection this way, try another Ethernet cable.
The whole idea here is to first confirm that the Ethernet LAN ports are working correctly on the AEBS. Assuming that the you can get a connection during your "test", this confirms that the AirPort Extreme is working correctly, and you will need to add the switch back to the network and test to make sure that it is working. Test each port with the computer.
Please post back on your results.

Using airport extreme base station modem to fax

Can I use an Airport Extreme Base Station with a modem to send faxes?
powerbook G5 Mac OS X (10.4.8)

kersto, Welcome to the discussion area!
No. The built-in 56k modem is only for connecting to a dial-up ISP. There is no ability to send FAXes.

AirPort Extreme Base Station with Modem not recognized by airport utililty,

My Apple M8799LL/A AirPort Extreme Base Station with Modem and Antenna Port is no longer recognized by the airport setup utility, nor will it allow internet connection. Has worked fine until last weekend when I did a full disk utility on all of my drives. Now I get a message, none of your trusted networks are available would I like to join (my network name)? Airport looks fine, can connect locally, lights up as usual.
How can I make it trusted again and get dial up internet to work again?

resetting has worked for months with no return of the problem.

How can I set up the airport extreme base station with windows computer

how can I set up the airport extreme base station with windows computer

Hi - you need Airport Utility version 5.6.1 for Windows 7 - go to http://support.apple.com/kb/HT1547 to download it to your computer - the setup depends on what kind of modem you have and if you have another router connected - post back with this info to proceed - thanks

New AirPort Extreme Base Station with OS X 10.3.9?

I have an iMac running 10.3.9 along with a XP box. Can I use the new AirPort Extreme Base Station with this setup. The sys reqs seem to say that I need OS X 10.4.8. I want to use this new wireless base station with AppleTV.
I really don't want to upgrade to 10.4.x especially since Leopard (10.5) is supposed to be coming out soon. Of course this supposes I can even run Leopard on my non-intel iMac.

I have an iMac running 10.3.9 along with a XP box.
Can I use the new AirPort Extreme Base Station with
this setup. The sys reqs seem to say that I need OS X
10.4.8. I want to use this new wireless base station
with AppleTV.
In order to connect to the new Airport Extreme Base Station 10.3.9 will be fine.
In order to use Apple TV then you will need to be running 10.4.8
I really don't want to upgrade to 10.4.x especially
since Leopard (10.5) is supposed to be coming out
soon. Of course this supposes I can even run Leopard
on my non-intel iMac.
You will be able to run 10.5 on non-Intel Macs.

I have a AirPort Extreme Base Station with Gigabit Ethernet 802.11n ?

I have the 802.11n Airport Extreme Base it went bad so Apple Sent me a new one to put into my
office where I have a iMac 24" 2.4ghz with really fast internet
I also HAD a AirPort Express Base Station with 802.11g and AirTunes G not N so when I received the
new 802.11n Airport Extreme I sold the Airport Express 802.11g now my Macbook Pro 17" 2.33mhz
which is in my family room and that is also where the Airport Express with iTunes was located
now my internet is like really slow on the MBP 17" I have 5 bars in the pizza menu bar but my
internet speed is really BAD on the MBP 17" and I have 16mg speed on the net
+BIG ? DO I NEED TO BUY A 802.11n AirPort Express Base Station with 802.11n and AirTunes??????+
TO EXTEND THE RANGE OF MY AirPort Extreme Base Station with Gigabit Ethernet Which is in my
Office where my iMac 24" 2.4ghz is located and the internet zooms on the iMac but not my
my Macbook Pro 17"
Please help as I don't want to spend money on another 802.11n if it will not extend
I
Message was edited by: macman60

So you agree to the lose of the Airport Express removal has caused me to lose enough of a signal to make the Internet...
Sorry but I'm not sure what this long run-on sentence is trying to say.
You asked if the network could be wirelessly extended and that is what I replied to.

Using Airport Extreme base station as wireless Cable router and airtunes.

Can I replace my wired Roadrunner cable modem with a Apple Airport Extreme wireless 56g router removing the wired modem out of the picture?
I just have read and have not come to the complete conclusion that the Airport extreme base station is a standalone wireless router.
I would like this if it is a wireless standalone router as I want to but a pair of wireless airtunes router for music around the house keeping the Airport Extreme in my room where the airtunes routers would not be as I have the computer in my room and I have iTunes right there and would not need the airtunes routers in my computer room.
Leon.

Can I replace my wired Roadrunner cable modem with a Apple Airport Extreme wireless 56g router removing the wired modem out of the picture?
The AirPort Extreme Base Station (AEBS) does NOT have a built-in DSL/Cable modem. You will still require a Cable modem in order to access your ISP's Internet service.
I just have read and have not come to the complete conclusion that the Airport extreme base station is a standalone wireless router.
The AEBS IS a wireless router, but it is NOT a combination wireless router & cable modem.

Can I use the Airport Extreme Base Station with my already existing D-Link router to increase signal strength?

I already own a wireless router that I would like to keep. Could I use this Airport Extreme Base Station to improve that signal strangth to my room from the living room or to the basement? Would I have to hard-wire both the Base Station and my existing router? You probably have read this question more than once, and I have read some questions of this product too, but for some reason these Apple products I have some trouble with.

Could I use this Airport Extreme Base Station to improve that signal strangth to my room from the living room or to the basement?
Yes
Would I have to hard-wire both the Base Station and my existing router?
Yes

Airport Extreme Base Station and 2wire Modem / Router

I have Yahoo DSL with a 2wire modem / wireless router combo. I have an iMac and a MacBook both running Leopard. I can't seem to get the Back to my Mac feature to work. I'm currently running the trial version of .Mac. I'd like to get a full .Mac account but I want to be sure I can utilize the Back to my Mac feature. If I were to bridge an Airport Extreme Base Station to the 2wire would that solve my issue with Back to my Mac. Additionally I like the idea of being able to plug a printer of external hard drive into the Airport Extreme.
Any advice is greatly appreciated.

I got it to work. I purchased the Airport Extreme Base Station and took the following steps which I found here http://forums.macosxhints.com/archive/index.php/t-68141.html
First connect directly to the 2Wire with the Ethernet cable.
Instructions from 2Wire:
1. Clear the HomePortal to Factory State –can be accomplished two ways
2. Go to http://homeportal/management
3. Click on Resets
4. Click on Reset to Factory State
5. Click Continue
6. Have customer press Hardware Reset button with paperclip (HG products only and BellSouth HWs)
7. Have customer unbend a paperclip
8. Have customer insert paperclip into recess for Hardware Reset button (outlined with Red circle) on back of HomePortal.
9. Hold paper clip in for ten (10) full seconds
Next steps:
1. Go to http://homeportal/management again
2. Click on Configure under Broadband Link
3. Enter VPI 0 and VCI 35
4. Click on Disable PVC Search
5. Set Connection Type to Direct IP
6. Click Submit/Save
7. Have cu go to http://homeportal/management
8. Click on Configure Services
9. Have cu Uncheck Enable Routing
10. Click Submit
Airport configuration:
1. Open the AirPort Admin Utility and select your Base Station.
2. Click Configure and enter your password.
3. Click the Internet tab.
4. Choose PPP over Ethernet (PPPoE) from the Connect using pop-up menu.
5. If required by your ISP, enter your user name, password and service name in the appropriate fields. ( Your name and password is you full email including the @sbcglobal.net part and your email password)
6. Click Update.
7. After the base station restarts itself, quit the AirPort Admin Utility.
If that doesn’t work call apple and they should be able to help with the airport configuration.
Back to My Mac now works. Hope this helps someone else.
Message was edited by: WalrusBoy

Airport Extreme Base station and speedtouch modem router

hi
i was wondering will my speedtouch(THOMSON ST585v6sl) modem router (wireless) work with the Airport extreme base station? or do i need a modem only?
thanks in advance

Welcome to the discussions, dood!
The Thompson ST585 appears to be a combination modem and router, so you could use one of the LAN ports on that device to connect an ethernet cable to the WAN port on the Airport Extreme. In this configuration, the Extreme would act as a "bridge" to the Thompson, which would function as the main router and supply the IP addresses for the network. You would be able to create a wireless network with the Extreme in this setup, but only the "main" network would be active. In effect, you have two routers in this setup.
If you connected the Extreme directly to a modem only, then it would serve as the main router for your network and you would be able to make use of the "dual band" wireless capability of the Extreme to create a "main" and "guest" wireless network. There are 3 LAN ports on the Extreme that you can use for ethernet devices.

Certain web address not available when using Airport Extreme Base Station

Hello. To access my "secure" account at the local library, I must use a web address that contains a colon followed by a number. I believe that this is a port number, but I confess that all the discussions here regarding ports are going well over my head, and I may be incorrect with this assumption.
My problem is that while I CAN access this site by connecting to my DSL router directly via ethernet cable from my iMac G5, I cannot access the site when connecting to the internet in the mode: iMac Airport to Airport Extreme Base Station to DSL router via ethernet.
The format of the web address is: http://xxxx.yyyy.net:####/zzzzz/, where #### is the number I guess may be specifying a port and causing my problem.
Can anyone advise me, in simple terms, how to get to this address when in the Airport--internet connection mode? Will the solution have any adverse side effects?
Regards and Thanks
iMac G5, 2.5 year old AEBS Mac OS X (10.3.9) Westell 327W 4-port DSL Modem, not using wireless feature.

Very likely the embedded firewall that comes with your AirPort blocks the port you are trying to use.
In order to solve this, best way is to modify the AirPort settings (open the AirPort maintenance app):
Click at the tab "port forwarding" and add the desired port as "public port" to the list. "private IP" is the IP of your Mac and for "private port" type in the port number again.
If you are unsure about the IP of your Mac, look at the network maintenance application.
Well, one side-effect is that you have an open port in your configuration which could cause security issues... but only if you are paranoid So there is nothing to care about (note that without the AirPort inbetween your Mac and your modem, this port would be not blocked and freely accessible

Using Airport Extreme Base Station As A Wireless Card?

Hi,
I don't know if this is even possible but here's what I'd like to do:
I've started to share an internet connection with a cousin of mine that lives in my apartment building. The connection is in her apartment and as far as I can tell the wireless signal is coming from the modem she has, there is no stand alone router/ base station. So far I've just been connecting using my iBook with the aiport card in it. No problems. I just had to get the ip number and password from her and I was hooked right up.
Here's my real question:
I also have a G4 Mini with no wireless card in it at all and an Airport Extreme base station from before we started sharing a connection. In the time that we've been sharing I haven't connected to the internet at all using the Mini. Now I'm wondering if there is a way I can hook the Airport Extreme to the Mini and somehow use it as a replacement for a wireless card in the Mini. Thus using the Mini connected to the Airport to connect just the Mini to the internet.
I'm not worried about the iBook and do not wish to reconfigure the way I'm using/ connecting with it. Everything is peachy with that.
If this is possible, how can I do it?
Thank you in advance for any help with this.

Ernest Lohrer wrote:
Hi,
I don't know if this is even possible but here's what I'd like to do:
I've started to share an internet connection with a cousin of mine that lives in my apartment building. The connection is in her apartment and as far as I can tell the wireless signal is coming from the modem she has, there is no stand alone router/ base station.
She has an "integrated" modem/router/access point.
So far I've just been connecting using my iBook with the aiport card in it. No problems. I just had to get the ip number and password from her and I was hooked right up.
Here's my real question:
I also have a G4 Mini with no wireless card in it at all and an Airport Extreme base station from before we started sharing a connection. In the time that we've been sharing I haven't connected to the internet at all using the Mini. Now I'm wondering if there is a way I can hook the Airport Extreme to the Mini and somehow use it as a replacement for a wireless card in the Mini. Thus using the Mini connected to the Airport to connect just the Mini to the internet.
I'm not worried about the iBook and do not wish to reconfigure the way I'm using/ connecting with it. Everything is peachy with that.
If this is possible, how can I do it?
Set up the AEBSn as a "bridge" and connect the G4 Mini to one of the "wired" internet connections.

Airport Extreme Base Station and DSL modem, IP address Conflict issues

I recently set up DSL service in my apartment. I have ATT yahoo DSL modem, and an Airport extreme base station plugged into it. The network works fine with my Vista PC connected to it, but when I try to connect my macbook to the network I get errors telling me the IP address the macbook wants to use is already in use, and my PC gives me an IP address conflict error.
The internet is fine, and the modem is configured automatically, so I think it must be a problem with the way the network is set up or the network settings on my macbook...
any ideas?

All,
I recently posted what I believe to be a similar/identical issue. See my post here: http://discussions.apple.com/thread.jspa?threadID=1378849
I have not changed my AEBS to "Off (Bridge Mode)" yet, because everything currently 'works' but I continue to get the occasional "Double NAT" warning suggesting I switch the AEBS to bridge mode. When this happens, I lose connection to the internet and need to unplugged both the AEBS and my modem to re-establish a connection to the internet and the external HD I have connected to the AEBS.
My question for Jmiller1138, do you continue to get the "Double NAT" warning even when you changed your AEBS to "Off (Bridge Mode)"? I am hesitant to change my AEBS to bridge mode since I'm assuming I'll need to totally reconfigure my entire network (meaning both the AirPort Extremes, my wireless HP printer, and my firewalls on my PCs).
The ignoring of the warning (i.e. closing the AirPort Utility without updating the AEBS) is what triggers the need to reset my AEBS and modem. Not fun.
I guess I'll just need to bite the bullet and set the AEBS to bridge mode . . . yes?

Using Airport Extreme Base Station with Cable Modem

Similar Messages

Maybe you are looking for