Using airport utility to control multiple speakers at the same time

Can I use the aiport utility on my Ipod to control multiple speakers/airport express units at the same time? I am able to do this directly in ITunes but when I use my Ipod as the "remote" by using the airport utility it only seems to allow me to play music on one set of speakers at a time. If I stream music to one set of speakers and then select a different set it stops the music that was going to the first set in order to stream it to the second set. I hope that this is just user error and not a limitation of the airport utility because I just purchased a brand new Ipod in order to be able to do this (airport utility wasn't compatible with me 2nd Gen). Thanks in advance for any help!

If you have not already done so, now would be a good time to perform a complete power cycle of the entire network.
Power off all devices...modem, routers, computers, etc....in any order that you wish
Wait a few minutes
Power up the modem first, and let it run 2-3 minutes by itself
Power of the wireless router connected to the modem next the same way
Power of the other AirPort routers one at a time about a minute apart
Keep powering up devices one at a time about a minute apart until the entire network is back up
Check the network

Similar Messages

I bought a bluetooth Bose speaker so I could listen to music from my imac in multiple rooms at the same time. I wanted to use BOTH my existing speakers using the headphone jack and add additional bluetooth speakers in other rooms, but the imac wants me to

I bought a bluetooth Bose speaker so I could listen to music from my imac in multiple rooms at the same time. I wanted to use BOTH my existing speakers using the headphone jack and add additional bluetooth speakers in other rooms, but the imac wants me to pick one or the other, is there a way to have both?

I asked same question
Any answers

Can I view the same pdf on multiple iPads at the same time with 1 iPad operating as the master (controlling page turns etc)?

Would like to use 4nr iPads as an autocue system. Can I view the same pdf on multiple iPads at the same time with 1 iPad operating as the master (controlling page turns etc) and the others operating as slaves? Can this be done without the use of 3G or a remote Wifi hub? I would appreciate your input.................

Open the document in Acrobat Reader and use the menu Window > New Window.

Can I pair and use more than one set of bluetooth speakers at the same time on my ipod touch 4.0

can I pair and use more than one set of bluetooth speakers at the same time on my ipod touch 4.0 or Iphone 4s or Ipad 2?

You can only connect to one device at a time using Bluetooth, See article below for more information.
http://support.apple.com/kb/ht1664
While your iOS device can maintain multiple pairing records, it can only connect to one headset or hands-free device at a time. This prevents your iOS device from sending your data to the wrong Bluetooth accessory.

Can you use sync on multiple computers at the same time? ie have someone else logged into your firefox account for you whilst you are also logged in

I am trying to sign up to something but there is only a short window so was going to ask a friend to sign in at the same time using my account to try to sign up (with my password being saved into my firefox account)

Hi. Yes, you can use Sync on multiple devices at the same time. I use it to keep my bookmarks in sync across my desktop and Android versions of Firefox.

How to use multiple proxies at the same time?

im planning to use multiple proxies at the same time on mac but i have no idea how to do it?!. i need help!thanks!

Is it possible to attach a bluetooth speaker to my mac and still use the mac's speakers at the same time?

Is it possible to attach a bluetooth speaker to my mac and still use the mac's speakers at the same time, so I can have music in two rooms (from the mac in the lounge and the bluetooth speaker in the kitchen? It seems to be a choice of either/or as when I pair my speaker the sound stops from the mac's speakers.

No.

Has anyone used switch control and siri at the same time?

Has anyone used accessibility switch control and siri at the same time?

Using Xmarks and Sync simultaneously will create a mess.
You can create a new profile, import the bookmarks from your main profile, and set up Sync for the new profile.
The flip side is, bookmarks from your main profile would not get synced with your new profile.
Alternatively, Xmarks is also available for Android.
https://play.google.com/store/apps/details?id=com.xmarks.android&hl=en

Can I export multiple folders at the same time, keeping the album structure

I'm exporting all of my photos from 2010 so far. Is there a way to export multiple folders at the same time, while keeping the existing album structure? It seems that when I try it, iPhoto exports them all to the same folder.
I really don't want to do this one album at a time, and here's why -
I'd like to select all of the albums, then export, using the plugin, to WalMart so that I can order prints.

Check out [iPhotoToDisk|http://www.iphototodisk.com/index.html]
I'd like to select all of the albums, then export, using the plugin, to WalMart so that I can order prints.
Why not upload to Walmart from iPhoto? Check out the first option here:
There are many, many ways to access your files in iPhoto:
*For Users of 10.5 and later*
You can use any Open / Attach / Browse dialogue. On the left there's a Media heading, your pics can be accessed there. Command-Click for selecting multiple pics.
Uploaded with plasq's Skitch!
(Note the above illustration is not a Finder Window. It's the dialogue you get when you go File -> Open)
You can access the Library from the New Message Window in Mail:
Uploaded with plasq's Skitch!
*For users of 10.4 and later* ...
Many internet sites such as Flickr and SmugMug have plug-ins for accessing the iPhoto Library. If the site you want to use doesn’t then some, one or any of these will also work:
To upload to a site that does not have an iPhoto Export Plug-in the recommended way is to Select the Pic in the iPhoto Window and go File -> Export and export the pic to the desktop, then upload from there. After the upload you can trash the pic on the desktop. It's only a copy and your original is safe in iPhoto.
This is also true for emailing with Web-based services. However, if you're using Gmail you can use iPhoto2GMail
If you use Apple's Mail, Entourage, AOL or Eudora you can email from within iPhoto.
If you use a Cocoa-based Browser such as Safari, you can drag the pics from the iPhoto Window to the Attach window in the browser.
*If you want to access the files with iPhoto not running*:
For users of 10.6 and later:
You can download a free Services component from MacOSXAutomation which will give you access to the iPhoto Library from your Services Menu. Using the Services Preference Pane you can even create a keyboard shortcut for it.
For Users of 10.4 and later:
Create a Media Browser using Automator (takes about 10 seconds) or use this free utility Karelia iMedia Browser
Other options include:
1. *Drag and Drop*: Drag a photo from the iPhoto Window to the desktop, there iPhoto will make a full-sized copy of the pic.
2. *File -> Export*: Select the files in the iPhoto Window and go File -> Export. The dialogue will give you various options, including altering the format, naming the files and changing the size. Again, producing a copy.
3. *Show File*: Right- (or Control-) Click on a pic and in the resulting dialogue choose 'Show File'. A Finder window will pop open with the file already selected.
Regards
TD

How to support multiple users at the same time?

Hi all,
I have a Labview software which controls a analyzer via GPIB connector. When user A is using the software, user B has to wait until A is done. But actually, the analyzer is not very busy, when user A is using the software.
I want user A, B, C and D can use the software at the same time. just like we can open Multiple websites at the same time.
How can I program the software, so that the software can be open multiple times? Do you have any example?
Thanks a lot.
Steven
Solved!
Go to Solution.

Are all the users going to be measuring the exact same thing from the same instrument?
It would be possible to write a separate instrument server application that would handle all the direct interactions with the instrument. When one of the users needed to access the instrument, they would gain access to it through this server.
The big, Big, BIG caveat is that each interaction with the instrument would need to be atomic. In other words each access would need to configure the instrument, initiate the reading, report the results, and then reset the instrument back to some known default value.
As Dennis said, not a trivial process, but probably do-able...
Mike...
Certified Professional Instructor
Certified LabVIEW Architect
LabVIEW Champion
"... after all, He's not a tame lion..."
Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps

How can I install one app on multiple iPads at the same time?

We have a volume purchasing account, but when purchasing an app we get multiple serial numbers that all seem to need to be entered individually. The iPhone config Utility will not sync multiple iPads at the same time. Am I missing something? This cannot be the method for mass deployment, it seem too complicated.

You can do a backup of you iPad then restore the backup to many devices.
How to use multiple iPods, iPads, or iPhones with one computer
http://support.apple.com/kb/HT1495
Mobile Device Management Solutions for iOS
http://www.apple.com/iphone/business/integration/mdm/
http://www.apple.com/ipad/business/resources/
"iOS mobile device management (MDM)
With an unmatched breadth of features, a Self Service console forover-the-air (OTA) distribution of in-house and app store apps, and integration with Apple's Volume Purchase Plan (VPP), the Casper Suiteallows administrators to easily achieve the four major tenets of iOSmobile device management: Inventory, Configuration, Security Management, and App Distribution."
http://jamfsoftware.com/products/casper-suite/

Is it possible to upload multiple files at the same time?

Hi folks,
It seems pretty trivial to implement a file upload item, but is there some way to allow selection (upload) of multiple files at the same time? Seems like this has probably come up before, but I didn't find much for solutions in my search. Any links or insight would be appreciated.
Thanks!
-Adam vonNieda

Thank you both for your replies.
@Manish - That does allow for multiple file uploads without refreshing the page, but does not allow for multiple file uploads at the same time.
@Tony - That might be the way I end up going, although I probably should have been more specific. It would be really nice it there was a way to do a mutli-file select using the control or shift button like you can with a standard file selection dialog (if you want to copy multiple files, for example). Having a separate line for each file browser means there has to be a limit on the number that can be selected at the same time.
Has anyone implemented a method of selecting multiple files at once, and hitting an upload button once to get them into the database?
Thanks again Manish and Tony, very helpful.
-Adam

CRVS2010 - open multiple rpts at the same time, like sheets in a xls file ?

Hi all,
is that possible to open multiple reports at the same time, like sheets in a excell file ?
Is that possible create tabs beside the MainReport tab ? or include reports in the Group Tree ? how can I do it ?
The application is in asp.net with VS2010 and CR2010.
The reports used to be in excell with three sheets and now we are migrating them to crystal reports, how can I create the report with those three sheets ?
thanks !
Subject modified as per the sticky post at the top of this forum; [Crystal Reports for Visual Studio 2010 Beta - read before posting|Crystal Reports for Visual Studio 2010 Beta - read before posting;
Edited by: Ludek Uher on Aug 31, 2010 7:33 AM

I'll make the suggestion to the Program Management group.
You may want to do a post to the [Crystal Reports Design|SAP Crystal Reports; forum and ask them how they's fake that sort of a requirement. E.g.; there may be some way to make this report look the way you want, but it will be best to ask the experts. Don't mention CRVS2010 as they don't support it and most likely you will not get an answer.
Ludek

WDS 2012 R2 - Cannot PXE multiple clients at the same time

Hello All,
This is my first post on here so I apologize if this is the wrong place. I work for a school district and we are implementing WDS 2012 R2. We've been extremely satisfied with the speeds and ease of use through unattend files. However, for
the past month I've been looking for a possible answer to a problem that has plagued us from day one of implementation.
So here's the problem:
I have a stand alone WDS server which is not a domain controller and is not our DHCP server. I have IP helpers and broadcast forwarders setup on the network. As well as option 66 and 67 in DHCP. So far so good right!
Well that's partially right. When we boot one client at a time to the WDS server. Everything works as intended. We can TFTP the necessary files from the WDS server. Everything boots up and we're off and running.
However, if we boot up two or more clients at the same time. The WDS server never responds to the traffic. The clients get their DHCP information. They start the referral and download from the WDS server, but get no response. I'm
really hoping that someone on here would have some insight of something I can try. I've about exhausted my list of peers and contacts. They're all stumped as well and were smart enough to stay with 2008 WDS.
I would prefer to stick with 2012 R2 since it's setup and working for the most part. With only this one hiccup.
Thanks in advance for any guidance!

Hello Daniel,
I appreciate the reply and apologize for taking so long to get back to this. Things have been a little hectic over here.
I have tried everything on this forum and I am still unsuccessful in PXE booting multiple clients at the same time.
Multicast is enabled on the server, and it works for the clients. However, as stated in the original post. I cannot boot multiple machines at the same time. I can start them from the image selection screen around the same time though. So,
that appears to be working fine.

Lightroom CC issues with multiple export at the same time

Back before Lightroom updated to the CC version, I was able to use export presets to send 4 different versions of the photos I'm working on at the same time (A Full Size for client at certain size, full size for myself, web-sized with watermark and a thumbnail). Since updating to the CC version, I'm only able to start the export process on two of these versions before the system simply becomes crippled and I cannot even navigate through Lightroom without it chugging along.
For reference, I'm running a 2014 rMBP with 16GB of RAM, LR is the only app open at the time and it's showing that I have roughly 6GB of RAM free when attempting this export.
TL;DR: LR5 worked wiht multiple exports at the same time, but LRCC now chugs after 2 exports are started

Re: "Selecting video in Messages, now starts Face time for video. Face time is one to one only."
Apple "Messages" supports two different types of video conferencing. It's become more than a little confusing. If you (or the person on the other end) ONLY have accounts set up for Apple's "iMessage" service (associated with your Apple ID and "iCloud") you may see the video symbol, but when you click on it you will be connected via FaceTime which is limited a 1-to-1 video conference.
However, if you have set up an AIM account in Messages (you may already have an AIM account ID if you once used iChat for video, audio and screensharing) and the person at the other end also has an AIM account you will be connected via AIM and will be able to do screen sharing and multi-person video conferences just like the old iChat, i.e. you'll have iChat Theater features, up to 4-way conferencing, etc.
It can get very confusing if, for example, you've signed up for AIM using a .me or .cloud email address. But once you have it set up and learn to recognise the way Messages switches between AIM and iMessage all the old iChat features work just fine in Messages.

Using airport utility to control multiple speakers at the same time

Similar Messages

Maybe you are looking for