Using Airport with itunes and as a wireless router- I'm confused!
Hello:
Since buying my Aiprort Express, I have used it to play music from itunes on my Windows 7 laptop, to my stereo. It works perfectly...or it did.
Last night, I configured the AE to work as a wireless modem so that when I am in a hotel with a wired internet connection, I can use my iphone and ipad. Again, this setup worked perfectly. However, now when I try to go back to scenario #1 and stream music to the stereo, the AE Utility can't find the AE and it has a blinking yellow light. I am using my original wireless network for scenario #1, not the new one created by the AE in scenario #2.
Can the AE be configured to do both of the above or did I wipe out the settings for scenario #1 when I set it up for scenario #2?
Thanks for any help you can provide. I'm not sure what to do since the Utility can't find the AE anymore.
You wiped out the settings for #1 when you set up the Express for #2.
You need to reset the Express back to factory default settings and then set it up again.
Power up the Express for a few minutes
Hold in the reset button firmly for 10 seconds and release
Allow a full minute for the Express to restart to a slow, blinking amber light
Now you can configure it for #1 again.
Similar Messages
-
after itunes finishes restoring my ipod touch 8gb, itunes still says itunes has detected an ipod touch recovery mode. You must restore it before using it with itunes. and i dont know what to do
Are you sure it is 1043? I've never seen that error before. But you can try disabling your security software, connecting the phone to a USB port directly on the computer (not a hub), and trying to restore again.
-
Multiple Airports with private and isolated guest wireless networks available from both
Hi,
I've been searching online for some equipment that can do what i want to do without going into the enterprise grade and spending $5000 on Cisco gear.
Consider two locations approx 80m apart - Primary is a house, and secondary location is a garage. A Cat6 run exists between the two.
The goal would be to have a wireless primary router in the house for wired and private wireless internet access, with an additional Guest wireless that is isolated from the private network that I can turn on and off if guests are coming over.
In addition, the second location should also support both wired and wireless connections.
It seems simple to me, one device in each location. The WAN port on the garage device would connect back to the house device. The two devices should be smart enough to know that one is extending the other. Someone on the guest wireless that is connected via the garage AP would not be able to see the wired devices even though it's traffic is going across the same wire back to the primary router.
Can I do this without spending a fortune?
ThanksTwo Apple AirPorts would do most....but not all...of what you want.
A few notes.....
In order for the guest network feature to work correctly on an AirPort router, the "main" AirPort in the house must connect to a simple modem......not a modem/router or gateway device. That is a deal killer for some users right there.
When the guest network is activated in the garage, it must be activated for both AirPorts....house and garage.
You could actiivate the guest network for the house and leave the guest network off in the garage if you wanted, no problem there.....but.....you could not activate the guest network in the garage without also activating it in the house first.
"Guests" can only connect to the guest network using wireless. Up to you to decide if you want to leave the guest network open or use a password that would need to be used to connect to the network.
But.....If "guests" had physical access to the AirPort in the garage....and they connected to one of the Ethernet ports on the AirPort in the garage, they would be connecting to your main or private network.
So, if something like this was a concern, you would have to either hide the AirPort in the garage and trust that users would not find it....or....find some way to limit access to the back panel of the AirPort so that users could not connect to it using an Ethernet cable.
If the features and installation limitations are acceptable, you could spend as little as $100 for each AirPort Express.
If you wanted better performance from the AirPort in the house, you could use an AirPort Extreme there...about $200 and an AirPort Express in the garage.
The deluxe option would be to use two AirPort Extremes.
Finally, you would want to make sure that you understood the store's return policy before you buy.....in case something unexpected crops up, as can sometimes be the case. -
I have an old PowerPC running 10.4.11 and a Macbook Pro running 10.6.7 sitting side by side. Both are using AirPort to connect to the internet wirelessly to the same wireless router. The old Mac connects with full bars but the MBP struggles with only 2 bars. Pls help, thanks!
BDAqua,
Thanks for the response.
Apple has used the term "Digital Audio" to identify this machine. System Profiler has the following information:
Machine Name: Power Mac G4
Machine Model: PowerMac3,5
CPU Type: PowerPC G4 (2.1)
Number Of CPUs: 1
CPU Speed: 800 MHz
L2 Cache (per CPU): 256 KB
Memory: 768 MB
Bus Speed: 133 MHz
Boot ROM Version: 4.3.3f2
Serial Number: XBxxxxxMK9
Sales Order Number:
Yes, I could connect them by ethernet if all I wanted to do was transfer files, but I would like to network them so I could use wireless internet. The machines are not always so close together, I did that to simplify the testing. With the very slow transfer speeds I am reluctant to move ahead with the internet step.
<Edited By Host> -
I have a Windows PC with iTunes and an iPod Touch. I also have a Verizon MiFi. I would like to be able to sync music to two locations. Would the Airport Extreme accomplish this, and if so, are there step-by-step instructions somewhere?
No, it will sync the ipod to the content of the MBA which presumably has nothing on it (= erasing content of iPod and replacing it with nothing).
Ideally:
iTunes: How to move [or copy] your music to a new computer [or another drive] - http://support.apple.com/kb/HT4527
do not confuse moving your whole folder and library with moving just media files as in
iTunes for Mac: Moving your iTunes Media folder - http://support.apple.com/kb/HT1449
Quick answer if you let iTunes manage your music: Copy the entire iTunes folder (and in doing so all its subfolders and files) intact to the other drive. Start iTunes with the option key held down and guide it to the new location of the library.
Macworld - How to transfer iTunes libraries between PC and Mac - http://www.macworld.com/article/46248/2005/08/shiftitunes.html
Move an iTunes library from a Windows PC to a Mac - http://www.macworld.com/article/1146958/move_itunes_windows_mac.html
if you absolutely must use the iPod:
Post by Zevoneer: iPod media recovery options - https://discussions.apple.com/message/11624224 - this is an older post and many of the links are also for old posts, so bear this in mind when reading them.
Commercial software utility for transferring songs from i-device to Mac - http://www.fadingred.com/senuti/
http://support.apple.com/kb/HT1848 - just media purchased from iTunes Store -
I have an Apple ID which I had registered years back.I wanted to use the same Apple ID to download apps on my ipod touch - but whenever I try to login with that Apple ID, it tells me "This ID hasn't been used with Itunes", and proceeds to let me "Review" it. In the last step, I'm asked to furnish credit card information, which I don't want to, since all I want to do is to be able to download free apps !!
Could the credit card be expired?
Beyond that, what you need to do is contact iTunes support, they can tell you exactly what is wrong, none of us here can do that.
In the lower right corner of this page is a 'contact us' link. Click on that and you'll see a page full of info and links, one of which is iTunes support. -
It´s possible to use the "Remote" app with Itunes and a Nokia E72 with Joikuspot installed only? Or I´ll need to buy a modem Wifi?
I was using "remote" with a D-link modem, that works fine at my iPad. But now I´m using only the cell phone as modem 3G, and don´t want to intall a router to put new cables at my notebook.What?
You want to control iTunes on your computer using the Remote app on your iPad?
And you want to connect the iPad and computer through your Nokia?
No, this will not work.
Just create a network with your notebook. -
How come I can't put music on my ipod? I already have a fair amount of music on my ipod but I have enough space for more. I am using a new computer with itunes and it is telling me if I wasnt to put the new music on my ipd i need to erase my ipod HELP!
Because you can only synce with one iTunes library and you are switching libries by using the new computer. To nake this yyour syncing computer:
- Move all the media(apps, music, synced video and photos etc) to the new computer.
- Connect the iPofd yo the computer and bake a backup fo the iPod by right clicking on the iPod under Devices in iTunes and select Back Up
- Restore the iPod from that backup.
Note that the backup that iTunes makes doe not include media.
To move mdia to the new computer see:
iTunes: How to move your music to a new computer
iTunes Store: Transferring purchases from your iOS device or iPod to a computer -
Hi, Unfortunately my Laptop has died (which had my iTunes on it). I want to ensure my music on my iPhone 5 and my iPad Air are backed up. Also, I want to sort my music in the way I used to with iTunes. How can I do this with just these two devices, i.e. NO Computer? Can the iCloud help? Why can't I download iTunes (i.e. my library as I saw it on the computer) to these devices? Thanks to anyone who can help me here.
You can change the email address of one's appleID...
I'd recommend changing moms email to yours to get a good backup on the Mac
Then switch mom's back to hers
Then change your account to the same email you used.
I've done something similar when I needed to update my Apple account (one ID changing email addresses and phone) -
The message function on my Ipad just quit working. I was using it while in Mexico and it just quit. I have come home and synced my Ipad with Itunes and function still does not work. How do I get this function to work again?
When I use find file http://www.macupdate.com/app/mac/30073/find-file (which does tend to find files that "Finder" can't), it's not coming up with any other itunes library files that have been modified in the past week, which I know it would have been - unfortunately, I don't have a very recent backup of the hard drive. It would be a few months old so it wouldn't have the complete library on it....any ideas? I'm wondering if restarting the computer might help but have been afraid to do so in case it would make it harder to recover anything...I was looking at this thread https://discussions.apple.com/thread/4211589?start=0&tstart=0 in the hopes that it might have a helpful suggestion but it's definitely a different scenario.
-
My iphone4 has been stuck on the connect to itunes logo for a few hours. I connected it to itunes and it says that the iphone is on recovery mode and that I need to restore it to use it with itunes. I'm afraid that if I restore it I will loose everything help please!!
AT this point whatever data you have on yoru phone is already gone since it is in recovery mode.
However you can restore from your backup, when your phone reboots from recovery.
YOu do have a backup right? -
i forgot password of icloud and i did restore with itunes and again it wants password, so now i cant do anything, i forgot e-mail password which is sending e-mail address. so i cant use my ipad, what can i do? how can i change i cloud address without old
Is your phone still signed in with your old iTues ID for iCloud (in Settings>iCloud)?
-
this is my problem ...I have a macbook pro version 10.6.7 and I cant install tunes 12 ....Ihave a i phone4, i cant use it with Itunes 10,,,I delete Itunes10,and now I cant use my Iphone with my macbook cause I don't have the correct version of Itunes,,,what is the version of Itunes i need to install?? i need it for my iphone 4 and my macbook 10.6.7
Run the Software Update pane of System Preferences or click here.
(121029) -
All of these steps were followed corectly. But a warning popped up and said that it could not be restored because it is locked with a pascode, and it said we must enter a pascode before we can use it with itunes. What should I do?
Place the iPod in Recovery Mode and restore via iTunes.
iOS: Wrong passcode results in red disabled screen
If not successful, try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings -
hi i updated my iphone 4 with itunes and now i cannot use my phone as i keep getting error 16 after trying to restore my phone....i cannot afford to replace ..can any body help me...the phone is out of warrenty so apple do not want to know....please any help
https://discussions.apple.com/message/23100453#23100453
more hits from the search
https://www.google.dk/search?q=restore+itphone+error+16&oq=restore+itphone+error +16&aqs=chrome..69i57j0l5.11485j0j7&sourceid=chrome&espv=210&es_sm=93&ie=UTF-8
Maybe you are looking for
-
How much data does a Ipod touch 8gb hold? Music? Games ? Apps?
How much does an ipod touch hold 8GB ? How much music ? How much Apps ? And how much games?
-
Hi PPl, It happened second time in a row. Though the root disk is mirrored, server is unable to boot from alternate disk (mirror disk) When the disk was found faulty, still unable to boot the OS from alternate disk, it says it still probe/look for ot
-
Using Data Acess Command Beans as Model
Hey guys, actually I try to get data from some EJBs (Entity Beans) into my Web Dynpro application. Inside SDN I found a tutorial which uses the 'Data Access Command Bean pattern' to connect the EJB-Backend to a WD application (The tutorial is called
-
Could any one help me finding the tables and fields for the following purchase order information? 1. Purchase Order Number 2. Order Date 3. Supplier code code representing supplier or vendor 4. Deliver to code - code representing complete name and
-
Why does NI-9233 with IEPE microphone report 39dBA as minimum noise level?
Hi, I have been using an ACO Pacific 1/2" IEPE microphone and preamp (7052SYS) with cDAQ and a 9233 IEPE module. The ACO mic is very similar to the G.R.A.S. 46AE (50mV/Pa) but with a 20mV/Pa sensitivity. Using this set-up in a hemi-anechoic chamber,