Using an Airport express to extend the range of my neighbor'd Belkin Pre-N

My wife just got an iMac 17" core duo and it is now a paperweight! She has been unable to get a signal from our neighbor's Belkin pre-n wreless router (I bought it thinking it would increase the range of the signal:(). She has an airport express, is there anyway to turnit into a bridge? If not what are my options for extending the range of the Wireless capabilities of the iMac?

Cgjheru, Welcome to the discussion area!
My wife just got an iMac 17" core duo and it is now a paperweight!
Why do you consider it a paperweight?
She has an airport express, is there anyway to turnit into a bridge?
To do this, you must use WDS to connect the AirPort Express wirelessly to another base station. This apparently works with only 2 Belkin devices (F5D7230-4 and F5D7231). If your neighbor has one of those devices it may work.
Does your neighbor know that you are trying to connect to their network?

Similar Messages

I have an old airport that still works, can you use it the same way that one uses an airport express to extend the range of an airport extreme base station?

It would save me a few bucks if I could use an old airport that I have to extend the range of a new airport extreme. My concept would simply be to use the old Airport the same way I would use a newer Airport Express as a slave repeater. Is this doable?

Both the new AirPort Extreme and older AirPort Express will have to be configured using Apple's WDS settings to provide more wireless coverage.
Here are the downsides:
WDS operates only at "g" wireless speeds, so you will lose all of the faster "n" wireless capability of the new AirPort Extreme
WDS cuts the bandwidth on the entire network in half, so you will have a "g" wireless network running at half speed.
WDS is difficult for most users to configure because it is easy to make a mistake and hard to recover without starting all over again
Bottom line......Saving a few bucks will be very costly in terms of performance on your network.

Using an Airport Express to extend the range of my Airport Extreme.

i've just bought an Airport Extreme and an Airport Express so i can connect my MacBook in my bedroom (second floor) to the DSL modem in the basement.
i was able to configure the Extreme as a base station but cannot figure out how to configure the Express to use as a relay.
no matter what i do, i cannot get the Express to show up in the Airport Utility, even when i have it powered in right beside the Extreme base station in the basement.
please help!

I have found that you need to have an Ethernet cord connecting the Airport Express to your Mac to set up the Express to work on WDS with your Extreme. Once it is set up, you should be able to see both the Extreme and the Express wirelessly, but for setup you need the wire to the Express.

Help: Using Airport Express to extend the range of Airport Extreme

I am trying to use the Airport Express to extend the range of the network created by my Airport Extreme. The Express works in terms of streaming music from iTunes on the PC connected to th Extreme.
However, I am trying to run a short Cat-5 cable out of the Express to a nearby PC in order to have access to the internet. If the Express is recognized by the Extreme and can play music through connected stereo cables, why can I get an internet connection through the LAN port..??
Here's a real basic representation of my connections...
Cable Modem >>-- Cat5 -->> Airport Extreme >>-- Wireless -->> Airport Express >>-- Cat5 -->>PC#2

To wirelessly extend the range between two AirPorts, you need to configure them in a Wireless Distribution System (WDS).
To facilitate the WDS set up, try the following:
o Perform a "hard" reset on the AirPort Extreme Base Stations & a "factory default" reset on the AirPort Express Base Stations (AX) before setting up the WDS.
o Place the base stations within near proximity of each other during the set up phase, and then relocate them to their desired locations when complete.
o To avoid having to "switch" wireless networks during the WDS setup, attach each of the remote/relay base station, via an Ethernet cable, to the main base station. Of course, this would be dependent on the AirPort types used for the main/relays/remotes.
o Be sure to jot down the MAC addresses for each of the base stations to be used in the WDS as these will be required during the setup.
o When enabling wireless encryption, configure the relay/remote base stations first and the main base station last.

Can I use an airport extreme to extend the range of my wireless modem

Can I use an Airport Extreme to extend the range of my wireless modem?
At one end of my house I have a dual band wireless ADSL modem which provides my internet connection and I want to extend (improve) the wireless coverage to the other of the hosue where my Apple TV (2nd gen) is located. I have being trying to extend my wireless network with an Airport Extreme but so far without success. I can get the Airport to join the wireless network, but I suspect that it is only acting as another client and not actually extending the wireless range. There is a setting in the Airport configuration to "extend and existing network", however when I choose this option the Airport no longer connects to my existing wireless network and I am beginning to suspect that this fuction only works with another Apple device (Airport Extreme or Express).
Has anyone been able to extend the range of a third party wireless router / modem with an AirPort Extreme? If so, any advice that you can offer wold be appreciated.
Regards
Michael

Thanks Tesserax,
Your answer has confirmed my suspicions.
Option 1 from your suggested solutions is not a goer because the modem and Airport Extreme are in different parts of the house making it impractical to run a cable between the two devices.
I did try option 2 and bought a Netgear range extender, which according to Netgear it would work with my D-Link modem - not.
However I have managed to work around the problem (sort of) by using the Airport Extreme to create a wireless network between my iMac 27 and my Apple TV. The idea is that the iMac will act as a router between ethernet connected ADSL modem and the wirelessly connected Apple TV.
The good news is that I am now able to play the content from my iTunes library on my Apple TV without interruptions due to a poor wireless connection . Although the connection from the Apple TV to the internet is not working I think this is most likely just a configuration issue and for me it is not really a show stopper.

I have an airport extreme attached to cable, then one airport express to extend the range. when i try to add an additional airport express to extend range in another area of house, can't get it to work. unility says it has found a new base station

i have an airport extreme attached to cable, then one airport express to extend the range. when i try to add an additional airport express to extend range in another area of house, can't get it to work. utility says it has found a new base station and asks if i want to use it. if i click yes, then the old setup is disabled.

Ok, thanks for clarifying which models you have. Please see the following Apple Support article on how to configure these older base stations for a Wireless Distribution System (WDS).

HT4259 I am trying to connect airport express to extend the range of my airport tower. What type of cords do I need to connect the airport express to a hardwired outlet in the wall of a bedroom?

I am trying to connect my airport express to extend the range of my network to a bedroom that is hard wired for internet. What type of cord/cords do I need to do that?

You can connect the AirPort Express to the wall port in the bedroom for the setup.....but first....if you have not already done so.....it would be a great idea to make sure that the connection in the bedroom is working correctly.
To do that, turn off the wireless on a laptop and connect the laptop directly to the wall port in the bedroom using an Ethernet cable. Make sure that the laptop can get a good Internet connection that way. If it can, this tells you that the cabling is working correctly, so the Express will work well when you connect it up.
If you don't have a laptop with an Ethernet port, then we'll have to assume that the folks that pulled the cables and installed the jacks tested things as part of the installation.
When you are ready to install the Express, you can use an iPhone or iPad if you have one handy for the setup.

How do I use my airport express to extend the wireless range of my NETGEAR 7550?

I am trying to extend the range of my Netgear 7550 using the airport express. When trying to set up the airport express it said that I was unable to extend the Netgear. Any ideas how to make it work?

You need to configure a roaming network.
Wi-Fi base stations: Setting up and configuring a roaming network (802.11 a/b/g/n)
http://support.apple.com/kb/HT4260

How do I resolve error 10057 when trying to set up my airport express to extend the range of my wireless network

I have a Dell XPS running on Windows 7 and use an AirPort Extreme 802.11n Wi-Fi to get wireless internet access for other laptops in the home. I want to connect an AirPort Express 802.11n into the network to wirelessly extend the range of my wireless network. I have installed the AirPort Utility but when I attempt to connect to the AirPort Express, it gives me an error code 10057 and says I should check the internet connection. I have tried resetting the TCP/IP settings on my PC but that did not fix the issue. The Airport Express is also flashing yellow rather than solid green. Has anyone found a fix for this issue?

This sounds as if you have an older AirPort Express that is no longer supported by the newer Mavericks operating system.
To check and see if that might be the case, locate the model number on the side of the AirPort Express. It will start with an "A" followed by four numbers. Hard to see in the faint print.....so you may need reading glasses or a magnifying class to see the model number clearly.
Model numbers A1084 and A1088 of the AirPort Express are no longer supported by AirPort Utility in Mavericks.
You will need to use a Mac running Leopard, Snow Leopard, or a PC to be able to administer the older AirPort Express.

How do I add an Airport Express to extend the range of my WIFI network with my iMac as a base station?

Hi people
I need help to configure a new Airport Express only to extend the range of my WIFI network.
My ethernet cable from modem is connected directly in my iMac and I am sharing the internet by WIFI inside home very fine.
Now, I would like connect my devices on my garden on backyard.
I can't move my iMac from their place and i just want add a Airport Express between the iMac and backyard to extend the range of WIFI.
But I can't to configure to that. On Airport Utility appear the Airport Express connected directly to internet globe, but don't work.
So, what can I do? What is wrong?
Thanks all and best regards.
Carlos Sgrillo, from Brazil.

The AirPort cannot do what you ask.
The Airport needs to connect to a modem, or another router......not to a computer.
The Express can only extend a wireless signal that has been provided by another Apple router.

Can I use an old Airport Express to extend the range of a new Airport Express?

Hi all. I have an old Airport Express 802.11g (First Gen?) that is starting to fade. Still works, but not what it used to be. So I am going to buy a new Airport Express. I'm not interested in the Airport Extreme.
Question: If I use the new Airport Express as my main wireless router, can I plug my old Airport Express into another room as an extender? In other words, with the old Express and the new Express talk to each other or will a new Express only allow extension with another new Express?
Thanks!

Sorry, but the old AirPort Express 802.11 b/g does not have a setting to "Extend a wireless network", so it cannot be used as a extender with the newer AirPort Express if you plan to connect wirelessly.
If you plan to connect the older Express using a permanent wired Ethernet cable connection, then it could be configured to provide additional wireless signal coverage in that manner.

How to use the airport express to extend the range of an existing airport extreme wireless network?

The instruction manual says nothing on the topic, so maybe it is not possible. The only reason I think it is possible is that two different Apple reps told my girlfriend it was possible. Now we have one, and no clue how to proceed.
We have an Airport Extreme, but its range is maximum 30 feet. We would like to double that. What do we do with the Airport Express? (We cannot move the modem nor the Airport Extreme. What we are trying to do has nothing to do with speakers, iTunes, or printers.)
thanks
Paul

Are both the Extreme and Express 802.11n models? If so, check out this AirPort Support article; if one or both are 802.11g models, check out this article instead.

HT1515 The wifi router I use to connect to the internet is in the room directly above me. I am trying to use my airport express to extend the network for better coverage down here. It works fine with the setting "join a network" but will not extend it.

I have 2 airport expresses. The issue is the same with both of them. What am I doing wrong?

I assume that you already have one Express configured to "join" the network.
Power up the other Express for a few minutes, then hold in the reset button firmly on the back of the device for 10 seconds and release. Allow a full minute for the Express to restart to a slow, blinking amber light.
Connect an Ethernet cable from the LAN <--> port on the "joining" Express to the WAN "O" port on the second Express.
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click Other WiFi Devices
Click on AirPort Express
Click the Other Options button and select the option to Create a new wireless network.
Follow the guided steps, and ignore the step about powering off the modem and restarting.
Once the Express restarts, it will still have a slow, blinking amber light. Open AirPort Utility and click on the amber dot, then select the option to ignore the Double NAT error so the Express will display a green light.
Select the wireless network that you named during the setup of the second Express and enter the password to connect to the network.

How do i use airport extreme to extend the range of my imac

I have an 2012 Imac and I would like to plug the Internet to my imac and use the the imac wireless and use my airport express to extend the range of the imac wireless signal. I am having an awfully hard time figuring this out - can anyone pass along a link to a document or any suggestions?
Thanks!

Apple's instructions for this are here:
http://support.apple.com/kb/HT4259
Although two AirPort Extremes are pictured in the example, the setup for a Time Capsule and AirPort Express would be exactly the same.
In general, a good starting location for the AirPort Express would be a point that is approximately half the distance from the Time Capsule and the area that needs more wireless coverage. You may need to experiment with the location of the Express a bit depending on the number of obstructions like walls and/or ceilings in the signal path

Using an Airport Express to extend my network range

Dear all
I live in a three storey house, my broadband modem/router is on the first floor and my Mac is on the third.
I noticed that I kept losing my internet connection and the guy in the Apple shop recommended that I buy an Airport Express to extend the range of my current wireless network (and thereby achieve a strong connection on the third floor).
I have bought the A. Express and my question is, do I need to plug my A. Express into the router or can I simply plug it into a plug socket on the third floor (with nothing wired up to it)?
What is the best way to extend my wireless network range?
Your help is greatly appreciated. I have read the user manual but it is not clear on this point.
Thank you

Dear Bob
Thank you very much for your prompt response.
No, unfortunately the Apple guy did not explain that I needed an Apple router/modem in order to extend my network range with the AirPort Express - how disappointing. I will return the product and look for an alternative.

Using an Airport express to extend the range of my neighbor'd Belkin Pre-N

Similar Messages

Maybe you are looking for