Using D-LINK dir-825 router and unable to print on hp laserjet 4000tn

i am using a d-link dir-825 router for my network but recently i have bought a used hp laserjet 4000TN printer for my small network. i can ping it from any where but i am not be able to print off it.
thank
ASe

plz try to download the following set of drivers from the link below :::\
http://gimp-print.sourceforge.net/MacOSX.php3
This is a new set of default drivers and mayhelp u in resolving the issue.
Plz do run disk first aid after installing the driver....might suggest even before installaing.
Thanx !! for trying.

Similar Messages

Unable to connect to DLINK DIR-825 router

I am trying to connect to a condo public wifi which uses a DLINK DIR-825 router. The network name and password is posted. I select the network in my wifi settings, and enter the password, and the iPad returns "Unable to join. Incorrect password". I have shutdown my iPad, restarted the router, and attempted to join the network several times, to no avail. Password is PSK2.

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Computer tend to freeze when accessing internet with D-Link dir-655 router

I recently bought a D-Link dir-655 router and since then my computer tend to freeze up completely when accessing internet. This also happens when certain programs access internet. Otherwise I am usually using Internet Explorer or Opera.
I've found that there are many who experience problems with D-Link router, that they may have problems with certain network card. Anyone who can say if this is a known issues and if it there is a solution or if it is better to buy another router?
Model #: HPE-140sc
Product #: WC779AA-UUW
Software-version#: A1PNv6PrA2
PCBRAND: Pavilion

Hi, Ernst:
Would you consider backing up your files and doing a system recovery?
Maybe the OS has some corrupt registry files or something.
If you recover and then it still does that, your only choice looking at the motherboard is a PCIe gigabit ethernet adapter which would be relatively easy to install, or you could even get a USB ethernet adapter and not even have to open the case.
See if there is a setting to disable the onboard NIC if you have to add a network card.
I would rule out all software problems before buying hardware.
If you want to try some other malware program, I recommend the free Kapersky rescue disk. You burn the file to a CD and boot from it. It scans the drive and deletes any malware or virus files it finds without the PC being in windows. A lot of times viruses and malware can't be removed when windows is running.
Link to the download and instuctions for use is below. I like to use the graphic interface rather than the text interface.
http://support.kaspersky.com/faq/?qid=208282173
Paul

PC cannot see wireless Airport Express using Ethernet on D-LINK DIR-655 Router

This seems to be a recurring issue going way back, but I have yet to see a real solution posted.
I am using my Airport Express (APX) to stream music from the computers on my network to my stereo via Airplay. I have APX set up to wirelessly join my existing wireless network, which uses a D-Link DIR-655 router hooked to a Time Warner cable modem. I can succesfully connect all of my wireless devices via Airplay, through iTunes to my APX, including two laptops and an iPhone. However, my primary desktop PC, which does not have a wireless card is linked directly via ethernet cable to my D-Link router, and it is not able to see my APX. I can, however, see the Airport Express from my PC through my Airport Utility by directly typing in the IP address. Note that the APX set-up option to allow Ethernet clients is checked. I also noticed that my laptops will stop detecting the APX if I directly connect them to my D-Link router via Ethernet and turn off their wireless cards. They will resume detecting APX when I turn their wireless connections back on. So, bottom line, I am convinced that this is not a firewall problem. Although I have tried every conceivable setting of my D-Link router and APX, I am convinced it is either a wireless to ethernet communication issue, or some obscure setting on APX.. Any help would be appreciated.
Thanks,
Wayne

I think I found the fix based on reading some Apple TV forums where several people were having the same problem. Under Advanced Network settings in the D-Link setup, I just checked "Enable Multicast Streams" and that seemed to do the trick.

Wireless connection to D-Link DIR-655 router

I just got a MBP and I can't connect wirelessly to my D-link router (WPA password protected; wired connection works great). Aiport sees the router, asks for the password which I enter, and then I get the message "the selected network uses and Access Control List.. and this computer is not on the list." I've tried to add the MBP to my network using the Network Magic process for adding new devices (which worked just fine to wirelessly connect my PC laptop from work), but it can't seem to find the MBP. I tried the steps suggested by iVmichael to someone having a similar problem April 5-6, and also tried disabling my network lock, but so far haven't found the magic combination. Suggestions?
MacBook Pro Mac OS X (10.4.8) D-Link DIR-655 router
MacBook Pro Mac OS X (10.4.8)

I had a similar problem and I needed a second computer (B) using a wired connection to the router to allow the other one (A) in. This is what I did:
1. Using the wired computer (B) I opened up the network so any computer could join the network wirelessly.
2. I joined the network with (A) wirelessly.
3. Once I had successfully joined the network with (A) I used the wired computer (B) to do a search for new computers so (A) could be registered in the Access Control List.
4. Using (B) I closed the network again.
5. Now I could join the network with (A) wirelessly without any trouble.

Setup D-Link DIR-655 router help

Greetings,
I'm trying to set up a D-Link Extreme Router (DIR-655) as the wireless router for my home. The setup wizard disc that came with the router doesn't appear to work on a Mac even though it says it's mac compatible on the box. I'm assuming I need to manually install the router which I have no idea how to do. My service provider is comcast and my modem is a scientific atlanta modem. I can connect to the internet by plugging Ethernet directly from the modem into my MBP. If anyone can point me in the right direction from here I'd really appreciate it.
desperately missing wireless,
JC

I have the same router D-Link DIR 655 coming and here is what I am thinking...
The CD is not for use with Mac, but finally on the net somewhere I found the answer to my question about plugging in and then immediately seeing the wireless connection, which I assume would be the case. Here is what I picture -- corrections welcome, as I will be doing this Monday. (I am way too spoiled using my iMac for a 'router' at home.. LOL it baffles the PC users... they can't find the router!)
Unplug the modem from the power supply.
Connect the Ethernet wire from the router to the modem.
Power up the router by plugging it in.
Power up the modem again by plugging it back in.
Now you should be able to see the wifi connection with a wireless laptop.
Type the default address 192.168.0.1 into FireFox and you should be able to skip to the Wireless configuration screen.
I'm trying to read about it as much as I can before it arrives. The thing I will have to do is this is for a business office and I'm not sure if I can also have another wire plugged from a computer into the modem as well as the router...because it makes me think that setup would two IP addresses. (I did this at home for years until the cable company shut me off... said I had to pay extra for 5 connections I was using with my hub!) So that will be a question for me to try to figure out.
Also, set the router on b and g not n, for the older cards, if you don't have the 'n' protocol.
So other than testing what I can do with my connection which is wired into the wall for another port on the opposite side of the room, I think that is how to start.
My first test will be to see if I can have the router connected on the opposite wall (because it will give a better shot for the signal to travel to the other rooms int he office) and have my laptop plugged in at the desk at the same time. The internet worked both from methods (plugged to the modem and plugged to the wall) but that was only one connection each time as I was alone doing this and only had a laptop with me.
Ideally I want the computer to be at the desk, able to plug into the modem, and the router across the way for the others to use on WiFi.
PS - the documentation was useless.. I am getting this info from reading other sources on the web....also be advised that you just plug in and get a WiFi connection I am going to assume it's 'open' and unless you are in a remote area at home, but in a building of other businesses like I am, you will need to password protect the wireless connection immediately.

I am shooting with a Nikon D60 on Fine Format and unable to print larger than 11x14. I have been able to print larger pictures. I am told iPhoto reduces the size of the file when uploaded. Is this true? If so how can I change this? I need 16x20's

I am shooting with a Nikon D60 on Fine Format and unable to print larger than 11x14. I have been able to print larger pictures. I am told iPhoto reduces the size of the file when uploaded. Is this true? If so how can I change this? I need 16x20's

I am shooting with a Nikon D60 on Fine Format and unable to print larger than 11x14. I have been able to print larger pictures. I am told iPhoto reduces the size of the file when uploaded. Is this true? If so how can I change this? I need 16x20's

Unable to print from HP Laserjet P1102 after upgrading to Mavericks

Unable to print from HP Laserjet P1102 after upgrading to Mavericks.

plz try to download the following set of drivers from the link below :::\
http://gimp-print.sourceforge.net/MacOSX.php3
This is a new set of default drivers and mayhelp u in resolving the issue.
Plz do run disk first aid after installing the driver....might suggest even before installaing.
Thanx !! for trying.

Setting up airport express with a d-link dir 655 router on xp

I bought a new router and would like to setup my old AX to use it to stream music. I installed the airport utility which seems to find my device but I can't connect to it - via my router or the airport utility. When I select select manual or continue I get a 60 second or so delay and then it returns to the same screen - "airport utility found an apple wireless device with default settings."
Wireless Network ebxxxx
Airport ID: 00:11:xxxxxx
Any ideas on what I'm doing wrong? My laptop is plugged into the same router that my AX is. I've tried what I believe to be a soft and hard boot with the AX but so far no luck.
Thanks
Chris

AS far as I am aware only the devices listed at the top of this page do UPnP
http://support.dlink.com/faq/view.asp?prod_id=1996&question=UPnP
On some, such as the 624 listed here http://docs.info.apple.com/article.html?artnum=93333 (See note 2) it actually doesn't work with a Mac properly.
The pics of the Menus on this page http://portforward.com/english/routers/port_forwarding/Dlink/DIR-655/iChat.htm suggest it does not have UPnP
The item in the menu "Application Rules" looks like a possible name for Port Triggering (A way of allowing Multiple computers use the same ports)
However it does not seem to be listed in the Port Forward Triggering guide list
http://www.portforward.com/english/routers/port_triggering/routerindex.htm
8:29 PM Wednesday; April 30, 2008

Link b/w router and switch

I am useing 2600 series router and trying to link it with a 2950 switch,
2950 switch is attached with a internet connection & layer 3 switches, 2600 series router is connecting with 2950 at the client permises, what will be the port configuration at both 2950 & 2600 series devices,
currently i configure sw mod trunk at 2950,
and IP at the fastethernet port of 2600 series router.
But when ever i try to telnet the router it cannot telnet

What VLAN are the devices from which you wish to telnet to the router ?
You need to configure the router as follows:
interface fastethernet0/1.10
encapsulation dot1q
ip address
Where VLAN is the VLAN you want to get to the router from ...
Pls do remember to rate posts.
Paresh

Using Sym Links for .dbf, .log, and .ctl files? Will this work in 10g?

Hello,
We have an old database server we use for testing/development and it's running very low on diskspace on one of the filesystems on the box. At this point in time, adding space is not a simple option for several reasons. However, there are several other data partitions on this server with plenty of space available.
I read a paper published by Sun Microsystems that advocates the use of symbolic links for dbf, ctl, and log files:
http://www.sun.com/blueprints/0103/817-1048.pdf
Are there any drawbacks/caveats we need to be aware of, or is this really as simple as just stopping the db, moving a few files to another fs, symlinking their locations, and restarting the db?
Thanks for your input/advice.

I think you should verify this with Oracle Support.
This is the perfect measure to have them drop the phone on you.
Sybrand Bakker
Senior Oracle DBA

Use Time Capsule with Existing Router and WAP

We've added an existing TC to a new network installation where there is now a Cisco router and separate wireless AP and a new SIP phone system. How do I best setup or reconfigure the Time Capsule so our customer can still use it for wireless backup from their Apple notebooks?
We seem to be getting conflcts with the Time Capsule on the same subnet--capturing network and Internet ports!
Thanks!
Chet - Houston

Go to internet page.. on the top menu item you are offered, internet connection by ethernet or pppoe.. choose ethernet.. on the menu option below it, you determine how the TC will share the connection. Choose bridge.. done. When you do that the TC will make the WAN port available to LAN.
chetpro wrote:
Is it straightforward to put the TimeCapsule into bridge mode?
The only thing the customer needs to do is their 'backups' with this unit. We will add a separate WAP on the subnet. I assume the Time Capsule can still reside on the same subnet...
There are mixed PC, Apple notebooks, and printers, and a new SIP phone system on this LAN.
Does the TC also capture or reserve ports that we can exclude?
Thanks,
Chet.
Why not use the TC as a WAP.. you bridged it and now it is already a WAP.
The TC will not capture any port that I know of. It will exist happily in the same subnet, although as I mentioned if the Mac clients lose connection after a day or two, there may be an issue with arp timing out or some discovery protocol not working. Lion is maybe more suspectible at the moment. The problem is inconsistent so not sure yet.

Printer is in use message, and unable to print!

Good Afternoon-
I work with a copier sales/service company, and I've been dealing with a driver installation issue that I'm hoping SOMEONE can help me with.
When installing a copier on a customer network, I use the manufacturer's installer file, and then configure the new printer in "System Preferences"... followed by some configuration settings in CUPS. Most times the installation goes off without a hitch, but occasionally when printing a test page (or ANY page for that matter) I see a "Processing-Printer is in use" message in CUPS, and then after 30 seconds or so, the job fails to print.
I set them up as a IP printer, using Line Printer Daemon with "lp" in the queue name, and the correct drivers. I've set up multiple machines in the same office, sometimes using the same OS-X version... only to have one of the devices fail to print. Everything else works correctly, including the built-in printer utility that's in the print drivers.
Can someone point me in the right direction... I'm stumped at this point.
Thanks in advance- Steve
(Please keep in mind for every 100 printer installations I do, 3-4 will be on a Mac.... and I'm Mac "Familiar", not fluent... so please answer accordingly)

Pahu-
Thanks for the quick response. I will change the configuration when I can get back to the customer's location, and see if that resolves the problem.
What's odd to me is I'm just wondering WHY some computers will print just fine with the LPD configuration, while others won't. I will try your suggestion though.. Deeply appreciated!!
Steve

Using an HP officejet pro 8500 wireless printer and unable to print anything web based/internet

checked wireless connection and it is fine but unable to print anything that is web based like an airline itinerary. McAfee says it is not the firewall. Any ideas?

Are you able to print other things than web based ? Like word documents, etc.
What behaviour you may see while printing from the web?
As well, did you tried the HP Smart Print toolbr Application?
http://h41112.www4.hp.com/bing_toolbar2/us/en/smart.html?jumpid=ex_r602_ww/en/hho/ipg/xx-mu-aw_chev/...
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

I am using firefox ver 8.0.1 and Canon LBP3200 printer. Whenever i give a print command from Firefox the browser crashes and the crash reporter asks for submitting the report.

I am using the printer in a network. the same problem is faced when giving print on the canon LBP3200 from the local computer.
its kind of very irritating.
Even if i open a pdf document in the browser and then give print command the browser crashes and the crash reporter appears.
Kindly help.

Sir
Following are the crash reports generated:
bp-8af5ab44-6b84-427f-ae16-36acd2111227 12/27/201102:29 PM
bp-bc804648-bbb4-4ac1-a93a-604052111219 12/19/201104:00 PM
bp-1fb97a23-84cc-4922-91d0-21a732111219 12/19/201104:00 PM
bp-c621113c-5446-4c16-8236-5a06c2111214 12/15/201101:07 PM
bp-2f51489c-adcf-4f9e-8f16-f6cf52111212 12/12/201102:24 PM
bp-5b9f3af7-d1e2-4882-b625-815cb2111212 12/12/201102:23 PM
bp-0b7389bc-7047-478c-a01c-03f3b2111212 12/12/201102:22 PM

Using D-LINK dir-825 router and unable to print on hp laserjet 4000tn

Similar Messages

Maybe you are looking for