Using Epson Workforce 40 with Snow Leopard and an AirPort Extreme
Hi. Long night working on this but I figured something out, that might help others out there in the same/similar situation.
I have an Epson Workforce 40, and an AirPort Extreme. I had previously set up the EPWF40 (Epson WorkForce 40) before I had installed Snow Leopard. After installing Snow Leopard, the printer would not work and would not be recognized by my MBP 15". The document would just hang and I would have to force quit the printer or delete the document.
Bullet points on how I made it work:
- the most important thing is to have the printer recognized by the router and have an IP address installed and registered first, then you can install the Epson Mac EasyPrint software and "find" the printer over your wireless network
- Goto:
http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?oid=108743&prodoid=6307 5463&BV_UseBVCookie=yes&infoType=Downloads&platform=Macintosh&x=28&y=3
and download the Epson EasyPrint v3.10 file called: "epson12433.dmg"
- Unfortunately, Epson does not make software to "install" the printer to the router for Snow Leopard
- I re-installed the printer to the router using my wife's HP laptop and the original CD that came with the EPWF40.
- Follow the instructions on the CD for the install for "First Time" setting up the printer.
- After following the original instructions from the CD on her PC, the router assigned a new IP address to the printer, and the printer was "connected" to the router wirelessly
- Then, on my MBP running Snow Leopard, I ran the dmg file downloaded earlier from the Epson website.
- After running, go to the printer/fax preferences, click the "+" sign and add a new printer.
- As long as you are connected wirelessly to the router, under default, your mac should "find" the Epson printer. It is called something like "EPSON5A2EAA". There should be at least one, if not two options.
- One of the options should be "EPSON5A2EAA Bonjour" and the other "EPSON5A2EAA IP". Click on one, install it, and then go back and click on the other and install it (just to be sure).
- You will not be able to use the standalone Epson Apps installed from the DMG, however, the printer preferences for the epson, will be available through the printer preference boxes when you go through the system preferences.
It didn't make any sense at first for me either. Once I understood that:
- you can't install the printer from a Mac to your router
- after the printer is installed and linked with your router, your Mac can find it and use it
...I was able to complete the installation and have a fully functional wireless network printer.
Feel free to drop me a question. I'm just glad I was able to make it work.
-j
Sota Boy wrote:
I installed Snow Leopard but my Epson WorkForce 500 printer is not compatible. I saw an article about loading Rosetta and this would solve the problem. I can't find the article and I have never used Rosetta.
Actually, you have.
Rosetta was incorporated into both Tiger and Leopard. But it was invisible, of course. Snow Leopard is the first OS that offers the choice of whether to install it or not.
Any suggestions on how I find the recent article or make my printer work with Snow Leopard?
Don't know about the "recent article", but you can install Rosetta by inserting your Snow Leopard DVD and clicking on the Optional Installs package. When the configuration choice window comes up, just check Rosetta alone and carry on.
Good luck with it!
Archie
Similar Messages
-
The copy and paste functions in iPhoto used to work in Snow Leopard, but not with the Lion. How do I copy and paste photos from one event to another? What I don't understand is that it used to work with Snow Leopard, and now that the OS has been upgraded to Lion, it doesn't?
Instead of copy and paste drag the photo to the new event. Or flag it and use the add flagged photos to selected event command
LN -
I used Roxio VHS to DVD for Mac (have iMac with Snow Leopard) and the audio does not synch with the video when playing in iMovie. Any suggestions to fix?
Thanks for the reply. I tried playing with detaching the audio in iMovie, but with 20+ hours of video to correct, it would take too long. After 28 hours, Corel/Roxio tech support replied that it is a known bitrate mismatch problem and they have no real fix. I strongly suggest not to buy this product.
-
Can't duplex print B4 paper size with Snow Leopard and HP8100N
Apple print drivers dumped the standard European paper size B4 (see ISO 216 for specs) many OS's ago, however, I was able to duplex print B4, which is a standard size for the HP8100 trays, using the HP Duplexing accessory, by specifying a 'custom' paper size (10.14 x 14.33). Now, with Snow Leopard and the 10.6.4 and the updated HP8100 print driver from Apple, I get the message "The Duplex Option, Flip on Short Edge" is not available when the destination paper is set to Custom."
It seems the easiest solution would be for Apple to bring back the B4 paper size--I don't know why they eliminated it. The next solution would be for Apple or HP (whoever is responisble for the print driver) to back up to whatever allowed duplexing of custom sizes in all recent OS's up to Snow Leopard.
I have thousands of pages of music to print and manual duplexing just isn't an option. Anybody have any work-around ideas?try converting your cmyk doocument to rgb and then print
-
Continuing font encoding and tag issues with snow leopard and CS4oI
I am looking for help with a font handling issue with snow leopard and cs4 Indesign. Despite numerous calls and hours on the phone neither Apple nor Adobe has been helpful. I have had this issue open with Adobe since oct 5 but they remain totally unresponsive to date. I need to be able to use Type 1 fonts and do the following , export a pdf from Indesign with the following attributes: 1) xml tags for stories and objects. 2) have the fonts encoded as ansi and embedded.
Some additional information - exporting to ps is not an option as it destroys the xml tags. and doesn't guarantee that the fonts won't become CID or some other odd encoding.
As it stands now,
Leopard (10.5.8) and CS3 creates ansi encoded fonts with xml tags.
Leopard (10.5.8) and CS4 creates ansi encoded fonts with xml tags.
Snow leopard and CS3 creates ansi encoded fonts and xml tags
Snow leopard and CS4 creates custom subsetted fonts and some xml tags.
If any one has any advice on how to force specific font encodings from CS4 pdf exports so that i can preserve the tags and get the correct fonts I would be grateful.The font encoding is not a function of the OS version, but rather of how a font is internally encoded and the content you are representing with the font.
If you are seeing a difference between MacOS 10.5 and 10.6 with the same Adobe software, it probably has something to do with use of a system font that is somehow different from one version of the OS to another. InDesign does not use any of the OS' font handling software.
Assuming that the fonts are embedded, subset or not, what is your issue with whether a font is ANSI-encoded, custom-encoded, or CID-encoded? It should make no difference for purposes of workflow beyond InDesign for software that adheres to the PDF specification (including all versions of PDF from 1.3 and up to 1.7 plus ISO 32000-1 PDF and all versions of PDF/X and PDF/A).
Neither InDesign or any other Adobe application provides user choices for the encoding since it shouldn't make a difference. The encodings chosen by Adobe's core technology components are for a combination of optimization and to support proper text search, copy, etc.
- Dov -
Hi, I have Mac with Snow Leopard and was trying to purchase Lion , so I can move to I cloud, when trying to buy the app I get a message that a minimum 2gb of memory is required. I went check the hard disck info and it says available memory 20gb :-(
Apple Logo, left hand side of the menu bar, About this Mac. It should be right there. If not then More Info, Sys Info.
But it would seem you don't have 2GBs installed and more then likely both RAM slots are already filed. So you just need to buy more RAM in a pair. That could be 2 1GBs chips or if your Mac can have more then that then 2 2 GB chips or 2 4GB chips.
Get your model # and go to Crucial.com and use their memory search to find out how much your Mac can have installed and the price for it. I suggest you install as much as it can take. Cost is very low on RAM these days. -
When trying to burn a playlist to a blank CD, iTunes 10.3.1 won't recognize the blank CD I've inserted (Verbatim CD-R). I've burned using these CDs before, this is a recent problem. Not the burner, as I can burn using Toast. iMac with Snow Leopard 10.6.8
What kind of CD are you burning (Audio or MP3)?
If you're burning an MP3 CD, the songs must already
be in mp3 format.
If not, iTunes will tell you that you have no songs
in the playlist.
M
I was making an audio cd. But I have since found out what the problem was. The files in my PLAYLIST I converted to aiff, since they were SDll files (I thought they were similar to AIFF, and they PLAY on Itunes...just won't burn.) When I selected the songs in the playlist and converted them...I thought all those files were converted, They were not. The converted files went into my LIBRARY, even tho I selected the ones in the playlist...and once I exchanged the SDll versions of the songs in my playlist. THEN they burned fine...but still...it's confusing..you say convert..it says it's been converted..and what they don't say is it's not been converted inside the playlist...where I had selected the songs...It just ADDED aiff versions..but only in the library...Anyway, that's what happened. But it's strange that it PLAYS SDll but won't burn them....and you'd think, logically..the ones you selected would change...but they don't. Playlists are mainly pointers to the actual files I guess...a sort of Alias..
At least it works now. But it's sad that the latest itunes does more, but also does LESS...as I used to be able to burn SDll files. Now I'll have to convert all my files to AIFF, and mp3's as I assume my ipod video won't play anything but mp3's? -
I have a canon multifunction printer that used to work with snow leopard but since I updated to mountain lion it stoped working. How do I make it work again?
This problem is not unheard of when upgrading from Snow Leopard. It is usually solved by completely deleting the existing printer in System Preferences > Print & Scan, and adding it again.
-
Good Morning,
I have a MacBook Pro 15" and my warranty just ran out! I partitioned my harddrive into two partitions, one with Snow Leopard and the other with microsoft.This morning I turned on my Macbook Pro and it will not boot into Snow Leopard. I shut it off took out the battery, reinstalled the battery. Then I put in the Snow Leopard CD and booted up to disk utility and The Snow Leopard partion would not show up?? I do see the microsoft partion.
I also rebooted holding down the shift key and still no Snow Leopard
Could you please tell me what I can do, what keys do I press on restart any advice to get Snow leopard back.
thank you.Have you restarted holding down the Opt key? That procedure should give you a gray screen with all of the partitions that exist. Then select the SL partition for boot. Also go to System Preferences and Startup Disk, unlock the lock and select the SL partition as the default boot partition, then relock.
-
I have a 27inch iMac with snow leopard and 1 user, and a 24 inch (older) upgraded to yosemite and 5 users. I want to wipe the 27 inch and transfer everything on the 24 to it. I do have time capsule 3tb but not sure how to do it
Move your content to a new Mac - Apple Support
-
My 10.7.3 Time Machine won't work with external disks. Worked fine with Snow Leopard, and even Lion 10.7.1
I have tried everything, even buy new external disk from different manufacture.
If I cant get a fix soon, I am downgrading back to SnowL.Still no luck. I tried all the tricks, reconfiguring TM (remove selected disk option, and re-setting it, and trying different disks). Tried new combo updater, and the newer TM update after that. Tired two different disks too (one is my older firewire WD MyBook 1TB, and my brand new 3tb Seagate GoFlex USB... either one plugged into back of computer - no intermediary devices). I did get the TM buddy wiget and it produced the following log, from the last attempt, where I setup lots of exclusions so that backup quantity was small (under 10gb). Still it failed to complete. Here is that log, for what it is worth:
Starting standard backup
Backing up to: /Volumes/TM-Disk/Backups.backupdb
9.56 GB required (including padding), 911.15 GB available
Waiting for index to be ready (101)
Copied 0 files (0 bytes) from volume Mac HD.
Backup canceled.
To prove a point, I will take these disks are run them on my other Tiger and Snow Leopard laptops to prove TM works fine on those with these disks. But I fear the only options are to either have my tech re-install LION... or just have him reinstall SL instead. Im at wits end. -
Dual Boot with Snow Leopard and Mavericks not possible?
I have a Early 2011 Macbook Pro with 2,3 GHz i7 Quad and two 512 GB SSDs (the secondary disk in an optical drive bay enclosure). This Macbook Pro can run Snow Leopard and Mavericks on the primary disk without problems. When I try to set up a dual boot system however, problems appear and it looks like it is not possible. When I start from Snow Leopard, I cannot select Mavericks as a start volume and vice versa. The error message says something like "Bless tool" cannot use this disk, i.e. unmount and boot from it. The problem remains when I exchange the disks (putting the primary disk in the drive enclosure and vice versa). When I put the secondary drive in an external case however, it is possible to boot from it - but strange things happen when the system starts: My computer clock is reset to 1/1/2001, WiFI passwords are not remembered for more than one session, disk permissions are reported as "repaired" but do apear as not repaired when I check them again - and other issues). I have verified both disks already and repaired permissions but that does not change the situation. So my experience is different from what is said in https://discussions.apple.com/thread/566781. It looks like the latest Mavericks cannot coexist with Snow Leopard on neiter a secondary internal drive nor on an external drive. This is strange since both disks and systems work flawless when run alone. Any suggestions to solve this problem?
When I check the Mavericks disk in the optical drive with disk utility after booting / running Snow Leopard on the primary disk I get som errors, see below ("disk utility Info"). So after all, I decided to erase the disk and install Mavericks new. But even erasing the disk is not possible when it is in the optical drive enclosure. I get this error message:
"Volume Erase failed with the error:
Could not unmount disk"
When I put this disk into an external case connected via USB however, it starts and runds MAvericks without any Problem. Same happens when I put thie Mavericks disk into the internal primary hard disk place.
"disk utility Info" when verinfying the secondary drive in the oprical bay:
Verifying volume “Samsung SSD Daten”
Performing live verification.
Checking Journaled HFS Plus volume.
Checking extents overflow file.
Unused node is not erased (node = 40)
Checking catalog file.
Unused node is not erased (node = 30)
Checking multi-linked files.
Checking catalog hierarchy.
Checking extended attributes file.
Unused node is not erased (node = 8)
Checking volume bitmap.
Volume bitmap needs minor repair for orphaned blocks
Checking volume information.
The volume Samsung SSD Daten was found corrupt and needs to be repaired.
Error: This disk needs to be repaired. Click Repair Disk.
Verify and Repair volume “Samsung SSD Daten”
Error: Could not unmount disk -
Setting up Time Machine with Snow Leopard and MyBook World Edition II NAS
I have just successfully set up Time Machine on my MyBook World Edition II NAS. It's not so straightforward, and the information on the Western Digital support site is either unhelpful or flat-out wrong, so here's a post that will hopefully save people in a similar position a lot of time and frustration.
Here are the key facts:
1. The MyBook World Edition II NAS does support Time Machine -- if you upgrade to at least firmware Release 1.01.14 (9/29/09). See http://www.wdc.com/wdproducts/updates/?family=mbworld. Amazingly, the Level I support people at Western Digital told me that Time Machine is not supported! I had to point him to this link.
2. MyBook World Edition II comes with a built-in user, WD_Backup, which appears to be the only user that can be used for the backup.
3. Follow the instructions here: http://www.wdc.com/wdproducts/updates/docs/en/appletimemachine.pdf. BUT, what the instructions don't tell you is the password for that user, which Mac OS will ask you for during the Time Machine setup. On my device, it was "admin" but other posts say the password can be "backup" or "wd_backup."
4. Ignore some of the misleading statements in the Western Digital "knowledge base." For example, it says Time Machine is not supported. That used to be true but with the firmware update, is no longer true. Also, some instructions direct you to make a partition on your drive for Time Machine using Disk Utility. This is not possible, as far as I can tell, because the MyBook World Edition II shows up as a "share," not a "device" in the system, and therefore Disk Utility does not see it.
5. The reason I wanted to set up a partition, where I could limit the disk space, is that I read that Time Machine creates daily backups, with incremental versions of documents. Thus, the Time Machine backup will eventually fill up whatever space is given to it. Since I could not partition the MyBook World Edition II, what I did instead was to enable the "Quota" functionality and then put a disk quota on the WD_Backup user. I hope this will do the trick. (I have the further issue of having two Time Machine backups, one for me, one for my wife. How our Time Machines will battle it out for the disk space, I have no idea.)
I hope that the Western Digital people will create greater flexibility for Time Machine users in future firmware updates.
Anyway, hope this helped.You do need to know that Apple may not support this: Here's the official word: http://support.apple.com/kb/HT1733 (Leopard) or http://docs.info.apple.com/article.html?path=Mac/10.6/en/15139.html (Snow Leopard).
You may be able to get it to work successfully, but there's no guarantee it will work well, or in the future.
From a post in another forum (found by V.K.):
The technical reason why Apple limits Time Machine to 10.5 AFP volumes appears to be to prevent disk image corruption. There were additional features added to AFP in 10.5 to support Time Machine. These presumably allow the disk image engine to force disk image journal data to write out all the way to the disk. Without such features, a network interruption can result in a corrupted filesystem on the disk image despite journaling. Remember, journaling relies on the journal being written all the way to disk before the changes take place. If you can't guarantee that (e.g., because of network/NAS buffering) then the journal is useless. Time Machine appears to rely heavily on disk journaling to deal with network drop-outs, interrupted backups, and the like. Take this away and your data is at risk.
If the NAS you are using supports these features it should report them to the OS and you should natively be able to choose that volume. If you have to trick the OS to use the volume it means the NAS does not support it.
To summarize: if you care about your backup data you should avoid using non-natively supported AFP servers.
That post obviously applies to Leopard; Snow Leopard appears to have added some requirements, that are also not supported by all NAS devices: some that were working with Leopard no longer work with Snow Leopard.
As long as you understand the risks, it's your call. But do yourself a favor and maintain some sort of secondary backup, such as a "clone" via CarbonCopyCloner or SuperDuper, or some other backup app. (Many of us do that with any backup app: no app is perfect, and all hardware fails, sooner or later.) -
Strange problem with Snow Leopard and Netware
Here is a strange one, but I am posting it here because I think it may have something to do with Apple software in Snow Leopard. I recently upgraded my Aluminum iMac to Snow Leopard, and have seen the following, rather puzzling behavior in the Prosoft Engineering client for Novell Netware. The symptoms are as follows. The server volumes mount OK, and I am able to see the files that are located on the server. In column view, when I select a file, I am able to see a preview of the file. Likewise, I can use Quickview to preview the contents of the file. However, when I try to drag a file from the server to my hard drive (any location), I get a dialog box saying I don't have permission to read that file. If I do a get info on the file, it says I have permission to read and write. For graphics files (such as Tiff, which have Preview as their default viewer), double clicking on the file causes Preview to open, but the file isn't opened. Now, what is really strange, if I use Photoshop CS1 to open that same file, it opens fine, and I am able to save it on the desktop, as usual. Likewise, if it is a Word or Excel file, they can be opened in their application, and saved on my hard drive. Does anyone have any idea as to what is going on, and how I can restore normal behavior?
Thanks in advance.Unfortunately I don't know what's going on, but we're having the same issue at work on two Mac Pro machines. We installed Snow and everything's been running as good as before or better - except for this issue. One machine had a clean install and one had an update install, and both are exhibiting behavior identical in every detail to what you describe.
We've contacted Prosoft and they're looking into it; official word on their website is that Snow Leopard is fully supported. -
Does Mozy back-up work with Snow Leopard and File Vault turned on?
I have SL and also have turned File Vault on. I am wondering if Mozy online back-up will work with SL and more importantly, will it work if I have File Vault turned on?
Thanks!Mozy works with Snow Leopard just fine. However, FileVault isn't supported well yet. From the release notes:
"If you are using FileVault, please turn off automatic and scheduled backups in the Mozy preferences. You will need to initiate the backup process manually while you are logged in. We are working on a better way to support FileVault."
If you stay logged in all the time, Mozy will function properly. If Mozy runs a backup while you are logged out, it isn't smart enough to do the right thing. FileVault mounts a disk image for your home folder when you're logged in and unmounts it when you log out. This causes Mozy to think you no longer need those files.
"We are working on a better way to support FileVault."
Maybe you are looking for
-
CPALookupException: Could not find channel in CPA Cache in PI 7.3
Hi, I am getting below error in PI 7.3 when trying to send data from SOAP sender Adapter. com.sap.engine.interfaces.messaging.api.exception.MessagingException: com.sap.aii.af.service.cpa.impl.exception.CPALookupException: Could not find channel in C
-
InDesign CS6 ePub. TOC is not linked
Hello using InDesign CS6 8.0.2 created the TOC and inserted at the begin of the book exporting as ePub 2.0.1 the inserted TOC is not linked to the page/chapter so I can't click on it to navigate the ebook. What can I check?
-
Please confirm, I cannot open RAW images in CS2 from EOS 50D
Platform: XP Pro SP3 After shooting my first session using the new Canon EOS 50D DSLR I cannot open RAW images in Photoshop CS2. Canon told me there was a free upgrade available to replace my current RAW editor ver. 3.7 BUT it appears from what I've
-
I can'treproduce musics through the aipor express with my ipod touch
-
Hi, There is a standard table T555U in this table there is only one field ZTERF, when i exceute and saw the contents in the table i found two columns Iho want to know from where the second column is getting appeared I want to print ZTEXT field in my