Using FBUS Monitor with FBUS-HSE/H1

Hello,
i want to use the FBUS Monitor SW with the FBUS-HSE/H1 (Ethernet) HW. But there is no interface to select. The NI FBUS Configurator works fine with the HW. I using the DHCP Server Tftpd32 v. 3.03. What can I do?
Thank you very much!
Harry Schäuble

NI-FBUS Monitor should be used with NI-FBUS Interface device.
For example, if there is a HSE/H1 linking device, you can use Monitor to obtain H1 data on this device by connecting a cable between H1 port on HSE/H1 linking device and H1 port on NI-FBUS interface card. But for HSE, NI-FBUS Monitor does not support the detection and capture of HSE data.
Feilian (Vince) Shen

Similar Messages

Can I use another monitor with my iMac desk top?

Can I use another monitor with my iMac desk top? Our monitor screen is going out and would like to have another option then replacing the whole thing! I think A LCD TV would be less expensive than the repairs to our iMac.( OS 10.6.8 )

Yes, but we need to know exactly which year model you have? So that we can advise you on exactly which adapter you need for you iMac.
see > How to identify iMac models
Plus, adding that Computer Monitors make better displays than TVs and comparatively cost a little less than TVs.
For examples of monitors that have both DVI and VGA inputs:
see > LG 21.5" Widescreen FlatPanel LED HD Monitor E2242T - Best Buy
or > HP 20" Widescreen FlatPanel LED Monitor W2071D - Best Buy

I am looking to buy a Mac mini, but I already have a monitor with a dvi plug in. Will I be able to use this monitor with the Mac mini??

I am looking to buy a Mac mini, but I already have a monitor with a dvi plug in. Will I be able to use this monitor with the Mac mini??

Here are the Mini's specs:

Using ADC Monitor with the new Mac Mini

My husband has an Apple monitor with an ADC connection. I would like to purchase the new Mac Mini, but would like to use his current monitor. I know there is an ADC to DVI adapter, but the new Mac Mini uses the Mini Display...could I use yet another adapter? I am trying to save money, but don't want to the display quality to be really poor. Space is not an issue. Any help would be greatly appreciated.

I have located that, but my concern is the DVI connection to the Mini Display connection on the Mac Mini. My understanding is that they are different.

How to use two monitors with my Mac mini

Hello,
I have a Mac mini and using a 20" Samsung Monitor with it which works well. I also have my 40" LCD Samsung telly, set up next to it. Whenever i watch a DVD using my Mac i have to swap over the cables. Is there a way of getting the right cables etc and making it so i would be able to watch a dvd on the 40" and still use the 20" surfing the net etc. I had a similar set up with my old windows laptop, but cant seem to work out how do it with the mac. Both monitors have modern sockets, the 40in has HDMI/DVI IN and AGV, the 20" has AGV and HDCP/DVI IN. Many thanks.

To the best of my knowledge there is no way to use dual displays on the Mini. You may be able to find some adapter that will allow you to physically connect two displays, but they will be mirrored, not spanned.
To do what you describe would take spanning, which the Mini is not capable of doing. Unless something has changed recently,..

How to use one monitor with two Power Macs

I searched this forum and was unable to find an answer. Although I believe it's probably here.
Nevertheless, I have a Power Mac G5 and a rarely used Power Mac G3. I'd like to share the G5's VGA Accusync 120 CRT monitor with the G3. I know there is a way to switch the monitor between computers without pulling plugs in and out of the machines.
Does anyone have any specific switch I could buy to solve this issue. I don't care so much for picture quality for the G3. But I don't want to compromise picture quality for the G5.

You're looking for what's called a KVM (Keyboard, Video, Mouse) switch.
This one should do what you're looking for. I've not used it, but it does VGA switching like you want and is inexpensive.

Can i use any monitor with my g5

I have an Apple G5 computer with a DVi-I output for a monitor> can I use any monitor and purchase an adapter to to fit the DVI output?

It depends on what the monitor actually supports, the size of the monitor, & the Graphic card capabilities.
At the Apple Icon at top left>About this Mac.
Then click on More Info>Hardware>Graphics/Displays and report like this...
NVIDIA GeForce 7800GT:
Chipset Model:          GeForce 7800GT
Type:          Display
Bus:          PCI
Slot:          SLOT-1
VRAM (Total):          256 MB
Vendor:          nVIDIA (0x10de)
Device ID:          0x0092
Revision ID:          0x00a1
ROM Revision:          2152.2
Displays:
VGA Display:
Resolution:          1920 x 1080 @ 60 Hz
Depth:          32-bit Color
Core Image:          Supported
Main Display:          Yes
Mirror:          Off
Online:          Yes
Quartz Extreme:          Supported
Display:
Status:          No display connected
Power Mac G5: Display Compatibility
http://support.apple.com/kb/HT2707?viewlocale=en_US
http://support.apple.com/kb/sp96

Can I use 4K monitor with my MacBook Pro Non-retina?

I am considering to use 4k monitor for my MacBook. I have mid-2012 15" MacBook Pro. But I'm afraid that it will not perform as good as standard hd monitor. I'm wondering if any of you have tried using 4k monitor for your MacBook. Thank you.

Won't work - at least not with 4K resolution.
Supposedly, the late 2013 retina machines with the NVIDIA GeForce GT 750M with 2GB GDDR5 memory will run 4K resolutions - but only in Windows 8, NOT in any version of OS X, yet.
So you'll just have to buy a new Mac Pro or wait until Apple comes out with an OS that supports running 4K on a new MacBook Pro Retina and buy that.
Sorry,
Clinton

Can I use LCD monitor with beige G3 233 mhz desktop?

Dear all,
I have a beige G3 desktop and want to use an LCD monitor with it.
I work mostly in OS9, but browse and email in OS X 10.3.9.
My Mas has the original video card in it, the ATI 3D Rage II.
Could I use a 19 inch LCD monitor with my Mac? Or would it have to be a 17 inch one.
I read on here that the mac treats lcd monitors just like CRT monitors.
what is the maximum resolution and monitor screen size I could use with my Mac?
Please help.
I only have a dinky 15 inch CRT monitor and would like a bigger monitor for Photoshop and animation work.
thank you

Both are probably contributing factors.
I know this will open up another can or worms, but you could consider overclocking your processor; most G3s will take a speed bump up a notch or two (266 or 300 in your case). It's relatively easy to do- search the forum for more info. As an alternative, a faster G3 chip (350-400) can be had rather cheaply from eBay (~$25). There are also a few 16MB Rage 128 cards on eBay, some as cheap as $10. Just make sure you get the Mac PCI version- AGP won't work. With the new video card and a speed bump, playing videos should be greatly improved. Just don't spend too much money on the old beast.

Unable to use 4 monitors with GTX 970

I used to run 4 monitors with my EVGA 660Ti. I recently purchased a Msi GTX 970 4GD5T OC and now my VGA only utility monitor on the DVI-I port (with included adapter) wont display when in windows. It displays the bios on boot but once windows 7 initializes it reads "no RGB input". I must be missing something simple that I did before with my 660Ti but I can't remember. Tried it with another VGA only flat screen I had and the same results.
Any help would be appreciated.

Do you mean by only DVI won't display or something? four ports on vga or some ports in onboard port? Did you check NVIDIA control panel 3D Settings--Configure surround, and right click screen resolution on desktop?

How use third monitor with W510?

My W510 (machine code 4318) is connected to a Minidock Plus Series 3 (170 watt version). I've attachd a VGA monitor (1280x1024 resolution) and a DVI monitor (1680x1050 resolution) to the minidock. I'd like to attach a third monitor. My understanding is that my W510 has no nVidia Optimus support, so the approach described here does not apply. My sense from googling around is that there are other solutions, but I'm not clear on the simplest and least expensive way to hook a third external monitor to the minidock. Can somebody please offer advice?
In case it's relevant, I use my monitors primarily for text. I don't play games, and I rarely watch video.
Thanks for your help.

ThorsHammer wrote:
See http://shop.lenovo.com/SEUILibrary/controller/e/web/LenovoPortal/en_US/catalog.workflow:item.detail?...
My understanding is that the minidock I have (model 433820U) has no USB 3.0 ports, unfortunately, so it looks like I'd have to manually unhook/hook up the USB cable from the W510 to the USB 3.0 dock each time I undocked/docked the computer. That's not terribly convenient.
At this point, it's looking like a USB-to-DVI or USB-to-VGA adapter is likely to be the easiest and least expensive way to go. (Presumably I can't go DisplayPort-to-DVI/VGA, because that would conflict with one of the two monitors I've already got hooked up to the minidock.)
Are there any gotchas I should be aware of regarding the USB-to-video approach?

Using External monitor with DVI kills wireless connectivity

I recently purchased a BenQ G2400WD 24" 1920x1200 monitor, for use with my May 2007 GMA 950 2.0Ghz. Macbook.
Upon receiving the monitor, I immediately plugged it in to my Macbook, using the Mini-DV to VGA adaptor I already had, for use with projectors. The monitor was good, but a bit blurry and not too sharp, due to the analog signal. So I ordered a Mini-DVI to DVI adaptor. When it arrived, the improved picture quality was immediately apparent.
However, as time went on, I noticed my wireless connectivity was getting terrible. Extremely slow Safari page load times, and upon going to Terminal and pinging my router, I would often get response times of 21000 milliseconds, or worse! I did a lot of research, on router firmware, on wireless connectivity, etc., but to no prevail. Then, on a whim, while continually pinging my router, I removed the DVI adaptor from my monitor. The ping instantly dropped from tens of full seconds to just a stable 0.4 milliseconds! Using my VGA connection resulted in no worse wireless connectivity than without it, but upon plugging in DVI and stressing the connection a bit (i.e. downloading a large file), the connection went bonkers. The pings also immediately jump from 0.4 milliseconds to a range of 1-4 milliseconds, regardless of any "stressing".
I have done numerous research, including searching both here and on other discussion forums. It appears this problem with DVI connection is fairly common, but with no resolution so far. Any help would be great!
A few important notes:
-Both ends of both my VGA cable and my DVI cable are shielded.
-I have tried numerous channel changes of my router, to no prevail.
-While using DVI, EVERYTHING works well except the wireless. So the monitor isn't too demanding for my computer.
And I hope my thorough post didn't scare you away!

I have this same issue with the dvi and wireless disconnect. I am using a samsung 214T. I am glad to know i am not the only one seeing this, because it is kind of one of those things that is hard to believe. Anyway, I am also curious what kind of routers people have who are experiencing this issue. I am using a wrt54GL with tomato firmware.
Also, In addition to the disconnect, my picture quality on my monitor gradually degrades over time...starting with what looks like snow flecks. After waking from screen saver, sometimes it is full static. Turning off and turning back on the monitor clears the static away.
I can use another samsung 19in monitor with dvi without any problems.

Using cinema monitor with top closed

A MBP C2D is driving a 30 inch Apple HD cinema monitor with the top closed.
USB KB and mouse connected to the MBP. OS 10.4.9.
Can use the power button on the display to switch from sleep (MBP sleep light pulses) to normal operation (sleep light steady on at medium). Sleep light behavior is not discussed in the MBP User Guide when using these conditions.
Can see no indication the MBP display is on.
So is this all normal behavior? And the best way to undertake daily operation when want only the 30 inch monitor as my display.
?

Personally, I would leave the screen lid cracked open a bit for cooling purposes. Air is drawn in through the keyboard to aid in cooling.
-Bmer
Mac Owners Support Group
Join Us @ MacOSG.com
iTunes: MacOSG Podcast
 An Apple User Group 

Using multiple monitors with Logic 8 & Reason

Hi Guys
Im using a macbook pro to run Logic 8 & slaving Reason with it. How do I connect another 2 monitors so I can look at Logic's arrange window on one, Logic's mixer on another and Reason on the third monitor?
Cheers guys
SS

SSuitor wrote:
Is anyone here using 3 monitors??!
Yes, but not on a laptpo, since you need a third video card and port.
On a desktop like the Mac Pro, you can use the first video card to run two monitors, and install a second video card for the third monitor.
Although, I can't see using more than two monitors....
Cheers

Using two monitors with Logic

I've never used two screens before, so can someone please answer these basic questions?
With LE and Logic Pro, can you have whatever window you like on each monitor - for example Arrange window on one and a score editor on the other? Or is it limited to certain combinations?
And if you've got the mouse cursor on one screen, how does the cursor get to the other screen? Key combination or just push the mouse further across?
Hope someoen can help!

Hi Robin
I´ve been using 2 monitors for several years now, and it´s very nice with logic pro. I can´t live without it anymore.
You can use whatever windows in combination to build different screensets. Think of it as it´s one big desktop. When you move the curser near the border off one monitor it pops up on the other. Go for it, you wont regreat it.
nice regards
Henning Flintholm
G5 dual 2.0 Mac OS X (10.4.8)
G5 dual 2.0 Mac OS X (10.4.8)

Problem using dual monitors with Radeon 9000 Pro and 2 x Samsung SM223BW

Hello all
I really need an expert opinion here:
I am using quite a lot my MDD 1.25Ghz that is still equipped with the OEM ATI 9000 Pro Mac Edition with 64MBs of Video RAM and as most if not all Mac-specific cards it has an ADC and a DVI port. I recently purchased a couple of Samsung monitors; the afore mention in the subject SM223BW. The monitors have two inputs, both DVI and D-SUB (Analog VGA or otherwise plain old RGB).
I have purchased a Formac ADC to DVI converter and connected this output to the DVI input of the first monitor. It works like a charm and the picture quality it is quite good (not as with an Apple Display but I couldn't afford them at this stage). For the second monitor I used a DVI to VGA cable (going from the DVI output of the card to the VGA In of the monitor).
Now here is the problem: The monitor that is connected ADC to DVI has all the available 16:10 ratio option that are suitable for this monitor. The DVI to VGA one gives me only a 1680x1050 and all the rest are 4x3 resolutions.
Would anyone know why this happens? Could it be a monitor issue? Could it be that perhaps TFT monitors offer different resolutions according to the input used. Or could it be the graphics card? Or even perhaps the cable?
Under OS X, same settings and same computer I am given more resolution options. Would that mean that it might be as well my beloved OS 9 in combination with the card?
Or am I stressing this too far?
Please any ideas are more than welcome
PS: I have a dual 2.0Ghz G5 connected to the rest of the DVI and VGA inputs to be able to run both without having to repatch. Otherwise a DVI to DVI connection would have made more sense and solved the problem

Hey Simon
I bought these monitors for their dual input functionality. The reason that I have the G4 connected to VGA is because I have another G5 connected the other way around in order to be able to use both computers, at any given time, with two screens.
Perhaps to make clear the connections I've done (if of course anyone is interested :)) ...
The G4 connects via ADC to DVI to the DVI input of Monitor No.1
The G5 connects via VGA to VGA to Monitor No.1
The G4 connects via DVI to VGA to Monitor No.2
The G5 connects via DVI to DVI to Monitor No.2
Another question would be why simply one mac isn't connected solely via DVI and the other one via VGA? The reason is that the VGA input looks awful on these screens for whatever reason. The image is seriously not sharp, the fonts looks horrendous and even with a lot of tweaking from the monitor settings, still I'd say the image is minging. If anyone knows why a VGA input can look that bad and still a monitor being in the market please let me know. It could be that this monitor is aimed to PC users and with the accompanying PC-only drivers all such are non-existent...Anyway I decided to go with the half DVI-half VGA solution to get the best out of the situation.
But on the question asked, I decided to use a 2 DVI input Avocent KVM that I've got with interesting results. I am pretty sure it is boring to read but if anyone has spare time here it goes:
The G4 connects via ADC to DVI to Monitor 1.
Monitor 2 DVI output connects to DVI KVM Input
The G4 connects via DVI to DVI to KVM Output 1
The G5 connects via DVI to DVI to KVM Output 2
The G5 still connects via VGA to VGA to Monitor 2
In this manner I am guaranteed to utilize the DVI inputs for both monitors, at least on my G4 and the G5 be forced to utilize one VGA. The plus side of the situation is that I can use both systems with the flick of a button without having to get up to change the Source on the monitors plus of course one keyboard and a mouse. Now here is the interesting bit:
Under OS 9, with the resolution 1280x800 on Monitor No.1 (the one connected via ADC to DVI) flips to - I think - 1680x1050 - it could be higher than that - with a thick black frame around the Desktop occupying a good chunk of the screen and the actual OS 9 looking minuscule at the center of it.
Monitor No.2 (the DVI to DVI connected one) looks just fine.
Now on top of that, when the G5 is switched on but the KVM is outputting the G4 desktop on Monitor No.2, whenever the mouse cursor slides on this monitor, it goes black! Just simply black and when I move the mouse cursor back on Monitor No.1 goes Desktop again.
Under OS X, none of the afore mentioned problems exist. Everything runs fine and I am give more 16:10 resolutions as well.
Confused? I am

Using FBUS Monitor with FBUS-HSE/H1

Similar Messages

Maybe you are looking for