Using labview to operate a signal generator

Hey everyone,
My name is Jake, I currently work in a lab at my university where we are trying to develop medical imaging via thermoacoustic tomography
The problem I am facing is that we are trying to use LabVIEW 2010 to "talk" to an SML-01 Rohde and Schwarz signal generator. I have very little LabVIEW experience anmd have basically been teaching it to myself for the past month. I have downloaded a driver for the sig gen and have a GPIB cable to run from an oscilloscope (which we run labview on) to the sig gen.
Would anyone be willing to help me figure out how to do this?

An existing Instrument Driver exists here
Edit{ ahhh you have the driver} What exactly are you having trouble with?
Jeff

Similar Messages

Using Labview control Agilent 33120A signals generated occurs an error occurs

hello,
The signal generator is the Agilent (33120A)
In Measurement & Automation which have caught this device (see below)
But VI execution to half Shique the following error window
in Initialize.vi, there is a problem
Such as photos
Seems to be unable to distinguish the devices?
How can i solve this problem? thanks~

Hi
Noticed that you are using serial port to communicate to instrument. Would you please double-check the serial setting parameters, such as Baud Rate, Flow Controls and etc. are insistent with the configuration on instrument? Or would you please try to use other interface rather than serial port.
If you have tried everything I mentioned above and it still raised that error, please manipulate the NI I/O Trace (You could find it in Windows Start menu) tool to trace and log the communication between PC and instrument. I should be helpful to analyze the root course if you investigate into that trace log. It would be great if you post it here!
Thanks,
- Charles

Using LabView to Operate a Pump

I am trying to use LabVIEW to operate a pump based on a temperature signal with two DAQ assistants, one for the temperature sensor and one for the pump. When the temperature reaches a certain point (30C in this case) the pump will turn off, and below that temperature the pump will be on. When the temperature is near 30C, the DAQ will rapidly turn the pump on and off, which is bad for the pump and the relay I am using. I tried averaging the temperature data and using a filter, but neither worked when the temperature is hovering around the cutoff point. Is there any way I can have the pump DAQ sample once a minute? When I try to change the Hz, I get an error message...

I think that the best approach is to utilize a Hysteresis setting in your on/off controller. It won't take much code. Here is an example:
In this you can see that initially the pump is on and is driven by the current value of Setpoint. When the Process Variable reaches the Setpoint the Pump turns off and the "Select" control will be looking at "Setpoint - Hysteresis". So if your setpoint is 30 and your Hysteresis is10, the Pump will not turn back on until the Process Variable is below 20. Once this occurs, the pump will be on until the process variable hits 30 again.
Edit: Woops, had an error in my code. Fixed it.

How interface N5181A MXG signal generator with labview by using LAN Interface????????????

hai every one ...i have a doubt how to interface N5181A MXG signal Generator with Labview by using LAN Interface???? and
how to find IP Address of N5181A MXG signal Generator????????
when i connect instrument with labview it shows that no instrument connected and what are the requirements for LAN interfacing with that instruments in labview and please help me??????

You can set the IP Address on the instrument. You may need to be in the same subnet of your controlling computer, so you may need to set your computer's IP Address to something static.
Use VISA. It makes life easier if you decide to use another bus (like GPIB, USB, serial, etc). In MAX, create a network session with the static IP address you set the instrument to and use that as the VISA Resource.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

Generating 0 and 1 signal using labview Daq card

Hello,
I’m working on a Project on the On/Off control of a pneumatic cylinder via a 5/2 solenoid valve.
On State: Valve O/P 1 pushes cylinder İ/P 1
                Value O/P vents air.
Off State: Valve O/P 2 pushes cylinder İ/P 2
                   Value O/P 1 vents air.
By this way we aim to move the clinder forward and back.
We use Labview 9.0. I did not work on pneumatic system before,
I will be happy if you could help me about 2 points.
1)      How can we enable the On/Off switching between the 2 O/P’s of the solenoid ?
2)      How can we enable the timing between On and Off States. ( On: 0-5 seconds Off: 0-5 seconds )
Do we need special code for Standard labview blocks will be OK ?
Thanks a lot.

The digital out are a great place to start, however they are signal lines which means they don't drive a lot of current (~1mA). If your device isn't setup to accept digital signals you may have to use an external transistor to step up your amperage. See the link on here to get started
Labview can provide all the timing you need. I would search through the shipping examples (Help >> Find Examples) for digital output examples, there should be a bunch and one will probably work for you with just a little modification.
Jesse Dennis
Design Engineer
Erdos Miller

Program to write signals from PXI 5105 using labview 2011

Hello
I am new in using labview. I need help in writing program to continuously record the signals form PXI 5105 using LabVIEW 2011. I prepared a program using help examples. It is recording the signal using pxi 5105 into the file after trigger. I tested the code using waveform generator with -100mV to 400mV, 1 kHz, sine wave. I have also attached the waveform of signal from the excel file recorded by the program. I have following queries
(i) Is the program correct to continuously record the triggered signals. Have I used the while loop correctly?
(ii) why some part in waveform is missing.
(iii) What should be the value of millisecond multiple ( I used zero)
I want to use above program for strain gauge signal measurement. Where I have to record the data at 20Ms/sec sample rate for 1 milli second after trigger.
thanks
Attachments:
Signal recording programme.vi ‏85 KB
recorded_signal.png ‏38 KB

Hi,
Sorry but I've only got LabVIEW 2010 so I can't open your file. If you can post a 2010 version I can take a look.
vinod_p wrote:
(iii) What should be the value of millisecond multiple ( I used zero)
If you are talking about the "Wait until Next ms Multiple" function then "Wiring a value of 0 to the milliseconds multiple input forces the current thread to yield control of the CPU." (from the context help for the function - press <ctrl>+h). Is this the behaviour you want?
Normally the ms multiple function is used to synchronise loops as it waits until the next multiple (be it 10ms or 10s) before continuing the loop.
-CC
"If anyone needs me, I'll be in the Angry Dome!"

How to use labview to control a robotic arm by EMG signal

Hello,
I am working on simulation of an active Exoskeleton (wearable robot) for the upper limb using LabVIEW for my senior project. I need to use the EMG signal as an input to move the elbow joint (flexing and extending). I downloaded labview biomedical toolkit to take a ready simulated EMG signal but have a weak experience in LabVIEW.
The design criterial I am planning to use is to establish a threshold for the EMG signal using a comparator (above 0 for example) and set a counter for everytime the signal passes the threshold as(+1) in every count. Then, specify a degree value for the counter (for example when the counter reaches 10000) and feed this value of the counter to a simple simulated structure for the joint (simple angle of 2 lines) or a meter to represent the movement.. e.g. every 10000 count = 1 degree of movement. Zero crossing can also be used instead of the comparator and the signal will be filtered and that is easy to do. However, my problem is in converting this logic into LabVIEW. I don’t know how to set a counter for the signal and make every number of counts refer to a specific degree of movement and I also don’t know how to form the simulated joint structure in LabVIEW or even how to transfer this into a simple meter device in LabVIEW.
I have only one month to do this project so any help or ideas you provide are highly appreciated
Thank you ,

CarlFHellwig
Thank you for providing this example I just implement it in the software to check the counter results.
In fact, the design criteria I desided to use latly is to use is to establish a threshold for the EMG signal using a comparator and correlate the EMG signal with the angles of movement of a simple simulated structure "motor" for a single joint (simple angle of 2 lines) eg. 30,60,90,120,150 degrees for flexing and extending. Zero crossing can also be used instead of the comparator and the signal will be filtered and that is easy to do.
In other words, the idea is to drive a motor for different angles based on the input EMG signals. I am now stuck with developing the algorithm of how the angles are related to the RMS value of the signal while flexing and extending and how to convert this RMS into angular velocity and angular position to form the simulation.
I will be grateful if someone guided me to a person did a similar project to discuss some issues.

I am trying to log data from 4 voltage input signal using labview, but when i use DAQ assistant i am able to log data from one signal at a time only.

I am trying to log data from 4 voltage input signal using labview, but when i use DAQ assiatant i am able to log data from one signal at a time only.I am trying to get all 4 input data to logged in a single file againt time. I am new to Labview, I need to sample this data within a couple of days can someone help please.

Naveen
Check out the info in the Analog Input section of the document linked below. (Ignore the part about Global Channels.) In Figure 5, notice that you can select multiple channels while holding <Ctrl> or <Shift>.
Developer Zone Tutorial: NI-DAQmx Express VI Tutorial
Kyle B | Product Support Engineer | ni.com/support

How can you create a test plan generator using labview

I am looking to create a testplan generator using labview to help RF Engineers translate test requirements into test parameters and wanted to know how i can go about it.

Have you considered to use Teststand? Teststand organizes all the tests and allows to parameterize them.
Creating a tool with a similar functionality will be more expensive than buying Teststand and modifing the operator interface.
Waldemar
Waldemar
Using 7.1.1, 8.5.1, 8.6.1, 2009 on XP and RT
Don't forget to give Kudos to good answers and/or questions

How to generate and print 20x20 datamatrix barcode using labview?

Along with the barcode certain datas are to be added to the right of it.

Since you started a duplicate thread - I'm going to continue in here.
We have given you a number of different options to generate/print a barcode using LabVIEW.
Do you have the Bartender software installed with the Automation (ActiveX) option? Can you print a label from within the Bartender Software? Do you know how to call ActiveX functions in LabVIEW? For the latter, if you Google 'calling ActiveX LabVIEW' you will get a lot of results. Once you know how to do that, you just need to know which Bartender ActiveX functions to call.
I've attached a couple of screenshots from some quick code my colleague put together before to initialise Bartender, open a label template, fill in a field and print a label. Don't forget the close the references when your application exits. For more information you'll need to read the Bartender documentation.
Certified LabVIEW Architect, Certified TestStand Developer
NI Days (and A&DF): 2010, 2011, 2013, 2014
NI Week: 2012, 2014
Knowledgeable in all things Giant Tetris and WebSockets

How to catch ACK signal by using LabVIEW?

Hi everyone,
I use 8451 to read/write and follow I2C protocol. Now, I want to catch the ACK signal. Does anyone knows how I should do by using LabVIEW?
Thanks.
Best Regards,
Catherine

Duplicate post.
Regards
JamesC
NIUK and Ireland

Can we demodulate the signal recieved at DAQ card without using any hardware interface(by only using labview)?

Hi all,
Can we demodulate the signal recieved at DAQ card without using any hardware interface(by only using labview)? if yes then how? please give brief idea.
Regards,
Amit

There is probably a way to do it, but it it may be easier to use an X-series board for the job. They support a new counter capability for count reset on a digital edge without needing to be configured in encoder position mode. I am not sure exactly how that feature's been implemented however, so maybe it won't make things easier after all.
The plan based on the hoped-for behavior:
1. Configure an X-series counter for pulse generation based on "ticks" of your clock channel.
2. Set both initial delay and low time to the critical # of ticks.
3. Configure for count reset on a digital edge (if possible in pulse generation mode)
4. Configure the count reset value to be the critical # (or possibly 1 less, if possible in pulse generation mode)
5. If you want the output to remain high indefinitely, configure the counter task to use its own output as a
pause trigger, and pause while high.
The way pulse generation works is to preload a # of "low time" ticks into the count register. Then every source edge will decrement the count. When the count reaches terminal count (0), the counter's output is toggled (or can be configured to pulse). The register is then loaded with the # of "high time" ticks and the process continues.
You would be perpetually interrupting the count-down process as long as you got your triggers in time. The count would keep getting reset to the # of low counts, keep decrementing toward 0 without reaching it, and so on. If ever you did reach 0, the output state would toggle high, then the high state would prevent subsequent clock signals from decrementing the count.
You can conceivably do a similar thing with a 6601, but I'm pretty sure you'd need 2 counters working together to get it working.
-Kevin P

Why the acquisition with DAQmx is different by using Labview 8.2 from Labview signal express?

Hello,
I am using a PCi-6281 to acquire a voltage. When I am using Labview signal express with only the step to acquire I read the good signal with the exact voltage. But when I am using my VI, the y axis and the values recorded are wrong. Why this difference appears?
I insert a picture with both signal: at the top is the signal from my vi (wrong measurement) and at the bottom is the signal from labview signal express (correct).
The vi I am using is the example Cont Acqu&Graph Voltage-To file (binary).vi.
Thank you for your answer!
Sophie
Sophie

I am using the binary file because it requires the minimum change in another VI. I have tried to change in scaled data but now my second VI has not enough memory to display all data.... What's wrong? Here is my second VI. Totest with data you need to insert a number in the "scaling factor" if not the dat are multiplied by zero...
thanks for your help!
Message Edité par stage84 le 07-24-2009 10:11 AM
Attachments:
Display 3.vi ‏1867 KB

I never used LabView but need to generate a RS-233 serial output string that contains an IRIG timestamp based on a contact closure. Is LabView an appropriate tool to do this? How much does it cost to get started with the product?

I never used LabView but need to generate a RS-233 serial output string that contains an IRIG timestamp based on a contact closure. Is LabView an appropriate tool to do this? How much does it cost to get started with the product?

Labview isn't cheap, but it would certainly allow you to build a program (set of vi's - virtual instruments) that would do what you describe. Where would the timecode information come from? Your vi, or program, would: Start up, initialize the serial port, loop until a trigger happened, read the timecode (from where?), output that timecode out the serial port in a loop until you pressed the stop button. There is a free evaluation of Labview software available from NI - the base product itself runs about $995.
- Dave

LabVIEW drivers for Agilent Noise Source 346B and Signal Generator E8257C-520

Could anyone please tell me where to find LabVIEW drivers for Agilent Noise Source 346B and Agilent Signal Generator E8257C-520. I did not find them on NI's web site. Thank you!

To my knowledge, the Agilent 346B Noise Source is not a programmatically controllable instrument and therefore we can't create an instrument driver. I suppose it is possible to be controlled through an instrument (like the PSG) but I don't see any documentation on this.
As for the E8257C, we are insterested in providing a LabVIEW driver for this instrument series. Let me know if you are interested in assisting our development effort by loaning us the instrument.
Jason Hobbs
Instrument Drivers

Using labview to operate a signal generator

Similar Messages

Maybe you are looking for