Using Latest SATA Raid Drivers When Installing Windows XP?

Getting my raid 0 setup on my K8N Neo4/SLI board wasn't as easy as it should have been. I ran into a few problem with my raid drivers that came with my system. While I was trying to install Windows XP, the system refused to restart itself even after the installation was done. A push of the reset button was necessary to help continue the install. Only after I installed the latest nForce 4 Forceware drivers was everything working the way it was supposed to. Since I would like to avoid this trouble the next time I decide to set up raid, how would I go about creating a floppy disk that contains the latest raid drivers to use for a Windows install? Thanks!

Download the manualhere. Then refer to from page 6-2, you will know how to configurate the raid.
My friend has the same mainboard as yours, so I just refer him for the information you need.

Similar Messages

  • I've encountered a problem about drivers when installing Windows on my Mac

    I am installing Windows 8.1 on my Mac mini Late 2012. During the installation, i got message saying "No device drivers were found. Make sure that the installation media contains the correct drivers, then click OK." Even though I have the pendrive where Boot Camp installed the drivers (WININSTALL) it doesn't seem to detect any drivers. Any help on how to get through this?

    Did you build the USB with Bootcamp Assistant and check the box to download the latest drivers?
    This is what a typical W8.1 USB structure looks like. Please check what you have on the USB.
    You can also directly download the drivers from Boot Camp Support Software 5.1.5621 to the Windows side, unzip them and run the setup.exe in the Bootcamp folder.
    System Requirements
    MacBook Air (11-inch & 13-inch, Mid 2011)
    MacBook Air (11-inch & 13-inch, Mid 2012)
    MacBook Pro (15-inch & 17-inch, Mid 2010)
    MacBook Pro (13-inch, & 15-inch, Early 2011)
    MacBook Pro (17-inch, Early 2011)
    MacBook Pro (13-inch,15-inch & 17-inch  Late 2011)
    MacBook Pro (13-inch & 15-inch, Mid 2012)
    MacBook Pro (Retina, Mid 2012)
    MacBook Pro (Retina, 13-inch, Late 2012)
    MacBook Pro (Retina, 13-inch and 15-inch, Early 2013)
    Mac Pro (Early 2009)
    Mac Pro (Mid 2010)
    Mac Pro (Mid 2012)
    Mac mini (Mid 2011)
    Mac mini (Late 2012) 
    iMac (27-inch, Mid 2010)
    iMac (21.5-inch & 27-inch, Mid 2011)
    iMac (21.5-inch & 27-inch, Late 2012)
    iMac (21.5-inch) Early 2013
    Windows 7, Windows 8, and Windows 8.1, 64 bit

  • Qosmio G20-102: RAID problem when installing windows xp media center

    First I didn't find the raid driver for my qosmio. I tried another Qosmio G20's RAID driver but when it reachs the stage when I ask windows to format the C driver it shows me an error. It says that it finds an error in the file KR10N and it ends there.
    please help me and thank you.

    Hi
    It seems that the Qosmio G20-102 belongs to the PQG20E series.
    Searching on the Toshiba European driver page I found the RAID driver v1.03.0008 for Windows XP MCE (can be used also with XP Pro).
    You will need an external USB FDD to include this driver into the OS.
    But note; after the RAID driver installation you shouldnt format the HDD or create a new partition because this will delete the RAID driver from the HDD and the OS installation fails!
    I hope I could help you would also appreciate a feedback ;)
    Best regards

  • HT4407 When installing Windows 7 using Bootcamp, I get message: "Need 64-bit Windows Installation USB drive or DVD."  I thought my install disk was for 32 or 64 bit.  What does this mean?

    When Installing Windows 7 using Bootcamp, I get message:  "Need 64 bit Windows installation USB drive or DVD."  What does this mean?

    It means you need the 64 bit Version of Windows on a USB stick or DVD.

  • Boot camp not recognize keyboard and mouse when installing windows 7 pro 64 bit

    Hi,
    I have some issue when installing windows 7 pro 64 bit using boot camp. after done partitioning the windows drive and when boot to windows installation process, i've got stuck in the first screen when choosing the language. it seems that the keyboard and mouse are not detected.
    i'm using boot camp ver. 5.0.
    does anyone have similar problem with me?

    I have finally successfully installed Windows 7 x64 on MacBook Air 13.3" (2013) thru Bootcamp.
    Problem:  After Windows 7 install thru BootCamp, I got to the first login screen and not input devices (Mouse, keyboard, USB) worked.   I tried to boot into Windows Safemode, but I received the error  "Windows can not complete installation in Safe Mode".
    Cause:  WIndows 7 does not have native USB 3.0 drivers, included on the install images.
    Resolution:  I downloaded the latest device drivers with thru BootCamp and copied them to the USB Flash Drive that had my bootable Windows 7 x64 install on it.  The second option in BootCamp is "Download Support Media".  This does more than just download drivers.  It creates a file called "autoattended.xml".  This is key as it tells Windows during the install process to use the device drivers that you download.  Otherwise, you need to do it manually, which you can't because you have no mouse or keyboard.
    NOTE:  I had no need of a super drive because I had all the files on one USB flash drive.  Therefore, I don't think it matter which side of the MBA the USB drive was plugged in, as other solutions suggested.

  • K8N 64bit sata raid drivers?

    ANyone know where or how to get drivers for intalling 64bit windows on this motherboard. I cannot find any sata raid drivers for this board for w64. Thankyyou

    Thankyou for your responses.  I did try extracting the nvidia files to a floopy but I must have done something wrong.  I did find a site that showed how to use the via drivers and make a txsetup.oem file, but that seemed to complicated. I know you folks will have an answer. Thanks again.

  • Do I need to install boot camp on Windows 7 as well as on Lion? I already installed it some years ago on Leopard when installing Windows Vista on my Macbook Pro. But now after installing Windows 7, many things in windows doesn't work (sound etc.)

    Do I need to install boot camp on Windows 7 as well as on Lion? I already installed it some years ago on Leopard when installing Windows Vista on my Macbook Pro. But now after installing Windows 7, many things in windows doesn't work (sound etc.). I made a clean installation because I needed to go from 32 bit to 64 bit.
    Or should I just update bootcamp in Lion? (cause when I search for "boot camp" in Windows 7 there's no result)

    Installation Guide
    Instructions for all features and settings.
    Boot Camp 4.0 FAQ Get answers to commonly asked Boot Camp questions.
    Windows 7 FAQ Answers to commonly asked Windows 7 questions.
    Apple Boot Camp Support
    Lion's Boot Camp Assistant 4.x should have downloaded Apple drivers as part of also partitioning.
    You need Apple drivers. And you then need to add on your own audio driver.
    You can run Assistant at any time to download and save a set of drivers.

  • Error when installing windows 7

    Hello... When installing Windows 7 Ultimate, I'm getting an error during the windows installation setup. I get the error 0x800024. I choose the correct partition, click install, and this error shows.
    I'm on a mac pro and on snow leopard. I have boot camp 3.0.1, which doesn't show windows 7 when it's about to reboot into the installation screen. Is there anything I can do?

    Have you looked here?
    http://support.apple.com/kb/HT3986
    Supposedly you need BootCamp 3.1 for Windows 7.
    On a MacPro you can't have the Mac OS in slot 1 if you going to install Windows on a second drive. Just put the blank one in slot #1 (that you want Windows on) and then Mac OS drive in slot #2, #3 or #4 and it should work then.
    Boot Camp can only use up to 2 partitions, Mac as #1 and/or Windows as #2. No 3rd partition. You have to have enough free space to use Boot Camp. If you have a 300 gig disk and you have 200 gigs worth of space used up it will only see the 100 gig of space left. And if it's an old disk you may not have enough CONTINUOUS space for it. The files may be all over and it can't find enough free space.
    If on a second (blank) disk what I did was use Disk Utility to format/partition (UFS, Journaled) the whole disk as 1 partition and then let Boot Camp/Windows 7 (I used XP) repartition the disk as NTFS as the first partition (for XP) and left the second (for storage) alone. Or in your case just let Boot Camp/Windows partition it as one NTFS.
    You have to tell it which one to use. If you don't have a choice then set the partition larger then 32 gigs then you should only have one choice, NTFS.
    The Mac can't write to an NTFS disk so it can't make a NTFS partition. So that is why you just partition it like you would if you were only putting the Mac on it. (On an already blank disk). Then when Boot Camp/Windows takes over then Windows can write the NTFS partition.
    The same with a Mac already on a hard drive. 1 partition. Boot Camp/Windows will then make the 2nd partition an NTFS partition (or what ever you want).
    Hope this helps....

  • VIA SATA RAID Drivers

    I lost the floppy disk containing the VIA SATA raid drivers for Windows Installation. My M/B is the KT600 FISR. So I kinda need the drivers as I am setting up a SATA drive.
    Can someone please say where I can get the drivers, or email me the attached drivers.
    My email is:
    [email protected]
    Thanks,
    Sam

    I am worried my floppy drive controller or something on the motherboard is not working. I tried the floppy disk containing drivers and Windows Installer said still said "Please insert the manufactuer's disk", I took out the disc and got the same message.
    Then I booted up Windows Installer with the same floppy disk in a different MSI motherboard (a P4 mobo I have) and it detected the drivers fine.
    Tried all the updated drivers you specified, and the floppy drive reads fine from Windows and is brand new (same problem with old one which I replaced only to find the same problem :
    The mobo is still under warranty, should I give MSI / dabs.com a call?
    Sam

  • Cs12 trial not responding when installed, windows 7 64bit...how to fix??

    cs12 trial not responding when installed, windows 7 64bit...how to fix??
    Not a very good recommendation for buying the app!!!!
    Does anyone at Adobe follow these questions???  If so please respond (your app will not!!)

    Hi wcarlstrom,
    Adobe CS12 is unheard of. Adobe Creative Suite's latest version is CS6.
    Please be specific as to what software you are trying to install, OS version etc so that I may be able to help you.

  • P965 Platinum SATA RAID drivers to slipstream

    Hey guys,
    Once in a while I slipstream SATA and SATA RAID drivers into my WinXP Pro setup cd, so I will not need a floppy on any system. My setup cd now contains drivers for VIA VT8237, nForce3, Promise 20378 and Promise 20579 controllers. I would like to add Intel ICH8R drivers...
    I know how to do it, that's not the issue. But on MSI's download section for my P965 Platinum I can find two drivers:
    Which one is to be used to setup RAID arrays on the ICH8R? Both contain contents for a floppy, both folders and files look the same. It's just that they differ in size, so I'm not sure which one I need. Do I need to slipstream both drivers to setup a RAID 0, 1 or 5 array?
    Thnx in advance...

    Quote from: Quadrifoglio Verde on 03-March-07, 23:47:11
    Alright, thanks. Why the first one and not the second one? Is there a difference between the two? I can not slipstream both, as they are both named "iastor.sys"...
    "I can not slipstream both, as they are both named "iastor.sys"..."
    you no need to put them both, only one of them.
    they are the same version, all files match except iastor.sys size (in same time both iastor.sys are "same version" too.. 6.0.0.1022)
    "Why the first one and not the second one?"
    just guess, because MSI put them as ICH8R SATA RAID Driver as primary. if you have any problems you can try drivers from second achieve.

  • The keyboard and trackpad on MacBook Air (13-inch, Mid 2013) computers may stop functioning at the Personalize step when installing Windows 7 64bit

    The keyboard and trackpad on MacBook Air (13-inch, Mid 2013) computers may stop functioning at the Personalize step when installing Windows 7 64bit.

    1. Reset PRAM.  http://support.apple.com/kb/PH4405
    2. Reset SMC.     http://support.apple.com/kb/HT3964
        Choose the method for:
        "Resetting SMC on portables with a battery you should not remove on your own".
    If this does not help, contact Apple.

  • RAID drivers that support Windows 2003 server for Qosmio G30-153

    Hi,
    Where can i find RAID drivers that support Windows 2003 server for Qosmio G-series(G30-153 )
    Thanks in Advance.
    Abdul Hameed

    Hi
    Windows Server 2003 should support the XP drivers.
    So try to search for the RAID XP drivers!
    regards :)

  • I am using XP-SP3 & Firfox.  When installing Flash Player Software i get a message: "This Publisher has been blocked from running software on this machine". How do i unblock it - HELP.

    I am using XP-SP3 & Firefox.  When installing Flash Player Software i get a message: "This Publisher has been blocked from running software on this machine". How do i unblock it - HELP.

    Hi,
    This is a security setting on your system that is resulting in this behaviour, not Flash Player installer itself, or anything with the installer.  There are many Google search results on this.  The first hit I got, was the following from the Microsoft forums:
    To unblock a software publisher:
    1. In Internet Explorer, click the Tools button, and then click Internet Options.
    2. Go to the Content tab, Look under the Certificates section.
    3. Click on Publishers button.
    4. Select the Untrusted Publishers tab.
    5. Select the Publisher you wish to unblock and click the Remove button.
    Maria

  • I am getting error "The disk is used for Time Machine Backup" when installing the new OSX Mountain Lion upgrade"

    I am keep getting this error "The disk is used for Time Machine Backup" when installing the new OSX Mountain Lion" when doing the upgrade to newly OS.

    The folder would be at the root of your hard drive. Double-click Macintosh HD and look there.
    If it isn’t there, I’m not sure what it is seeing.

Maybe you are looking for

  • What is the patfrom_id for linux_x86_64

    HI I am trying to find out what is the platform_id for a database running on the linux_x86_64 platform? I do not have a database if this type available to me and need to know as we are looking to use data guard to migrate an existing 10.2.0.3 databas

  • Is there a way to identify MRP requisitions transfered to SRM?

    Hello experts, We are using SRM 5.0 connected to an ECC 6.0 backend system, using ECS scenario. I have the following question: Is there a way to identify in SRM requisitions transtered from ECC that are created in R3 from an MRP process? Meaning like

  • ADOBE Forms (Creating Dynamic Forms)

    I am currently creating a form using Adobe Professional 8. IT is three pages each created on separate form files (.pdfx). I combine the files into a PDF package. I want to link up the pages together so that when the user types in a value on the first

  • Redirecting System.err to a JOptionPane

    Hello, I tried to write a piece of code which shows all exceptions in a JOptionPane instead of the console. But I meet two difficulties: 1. I don't know how to detect the line count of the error message (so that currently I have to display the option

  • Cant Hear any sound, only wen i use my headsets

    no sound my volume dosnt go up or down only works with headsets