Using Mac Mini and a 26" Samsung Tube TV with Apple DVI to Video Adapter
So upon first hooking this adapter up from my Mac Mini to my samsung 27" tube TV, it worked fine–but everything was massive in size. I started changing resolution sizes in the preferences panel and one of them set the screen flickering vertically, like a mismatch in refresh rates.
Anybody else have this issue and resolve it successfully? It obviously works, it was for me for the first couple minutes, but I can't figure out what sent it flickering–and how to resolve it.
The TV is connected VIA composite (RCA) cable from the adapter to the video-in port.
Try starting in Safe mode. That should get your screen back.
http://support.apple.com/kb/HT1455?viewlocale=en_US
See also this article:
http://support.apple.com/kb/TS2213?viewlocale=en_US
Similar Messages
-
Apple DVI to Video adapter + Mini DVI to DVI adapter pins not same
I just purchased an Apple DVI to Video adaptor so I could plug in a Mac mini to an older tv, however the pin arrangement on the Apple DVI to Video adapter is not the same as the pin arrangement on the Mini DVI to DVI adapter that came with the Mac mini.
Anyone have any idea what adapter I can use to make this connection?Joseph Kriz wrote:
James,
I'm confused here.
Which Mini do you have?
I know you posted this in the 2009 Mac Mini section so your Mini should have 2 video out ports.
1. Mini DVI
2. Mini DisplayPort
If that is true, then there is no way you could have connected the DVI to Video adapter in your first post as the new Mini does not have a DVI port.
The new Mini's come with 1 adapter.
Mini DVI to DVI adapter.
I don't know of any Apple adapters that will output to S Video, component or composite connections on the new Mini's.
The one that osxdude shows above will not work on a new Mini. It say nothing about a Mini in their description:
*The Mini-DVI to Video adapter is designed for the iMac (Intel Core Duo), MacBook*, and 12-inch PowerBook G4, allowing you to connect to most S-video or Composite enabled devices.*
Good Luck and let us know what you find.
Yes, I have a late 2009 Mac mini. It came with the mini DVI to DVI adapter as you stated. I need to hook up to an older tv with yellow component video port. Not knowing any better, and looking online, it looked like the male DVI end of the “Apple DVI to video” adapter would connect to the female DVI end of the “Mini DVI to DVI” adapter that came with the Mac mini. I figured that since they were both DVI plugs, male and female, they would connect, but the “Apple DVI to video” adapter has 4 extra pins, so they won’t.
Then, following osxdude’s lead, I went to a local independent Apple store, and they told me that the same adapter that osxdude suggested would work, so I bought that (at an inflated price), but as you stated, it does not work. Also, as you stated, the Apple site does not list the Mac mini as being used with this adapter, which is why I did not originally purchase it online. It was only at the insistence of the independent Apple store that it would work that I purchased it. Unfortunately, once the package is opened
the store were I purchased it will not take it back. Boy... this is getting expensive, and confusing! Why so many adapters?
After much searching I found this info: http://forums.macrumors.com/showthread.php?t=706736&highlight=monoprice so I’m going to try that.
Once it’s all said and done, I guess I’ll be listing a few adapters on ebay! -
Please help! We got a used Mac Mini and we don't have the former owner's password, so we can't install anything like flash player. Does anyone know how to get around this? I don't know how to wipe the hard drive, and the support online doesn't seem to work.
As posted previously:
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
If installing Leopard the process is similar in some respects. If you wish to begin anew then after selecting the target disk click on the Options button and select the Erase and Install option then click on the OK button. To install over an existing system do the following:
How to Perform an Archive and Install
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update. -
bought a used Mac Mini and can't get past security password Seller refuses to answer emails. is there a keyboard command to take it back to factory settings or do I need to buy a Disc set and OS???
You can bypass the password and wipe the drive and return to the original facory installation if the seller included the orginal install DVDs with the Mac mini. If not you will need a retail version of Mac OS X. To boot from the Install DVD restart the mini, immediately slip in the DVD and press and hold the C key.
-
I am looking to buy a Mac mini, but I already have a monitor with a dvi plug in. Will I be able to use this monitor with the Mac mini??
Here are the Mini's specs:
-
Apple DVI to Video adapter M9267G/A and extension cable
Will the Apple DVI to Video adapter M9267G/A work with this cable?
http://shop.vendio.com/dcables/item/899653106/?s=1181815202
Also, is it safe to "hot plug" the adapter, or should I only plug it in when the Mac is off?
I bought the adapter used with no documentation, and couldn't find any setup instructions on Apple's downloads page.
Thank you.Hi-
So you're trying to extend the reach of the adapter? Closer to TV, VCR, etc.?
Seems like it should work, though I would personally get a long S-video/composite cable. Cheaply constructed DVI extensions can cause a loss of signal strength, and/or pick up RFI and result in poor performance.
It would be safe to hot plug the adapter itself, though I would not power on the attached devices until after connected to the adapter.
G4AGP(450)Sawtooth, 2ghz PowerLogix, 2gbRAM, 300gbSATA+160gbATA, ATI Radeon 9800 Mac OS X (10.4.8) Pioneer DVR-109, ExtHD 160gb x2, 23"Cinema Display, Ratoc USB2.0, Nikon Coolscan -
Can I use the "Apple DVI to Video Adapter" with the GeForce 8600M GT?
It's all in the subject, folks. I've got an nVidia card, not ATI. Should I go ahead and buy the Apple DVI to Video Adapter to connect my MacBook Pro to my CRT Sony TV?
Thanks.
PS My May 2005 Powerbook G4 had both a DVI and sVideo connector. I used to use the latter to connect to view on the TV. Now, my Powerbook is dead...The first review posting on the product page is:
+dosen't work on mac pro with nvidia!!!!!+
+Written by PH from hamburg+
+August 27, 2007+
Which suggests no. I have heard from an Apple Store "genius" that it does.
Both are n=1, so I'd suggest a call to the Apple Store sales line (even if you don't order it that way). -
Can I use Apple DVI to Video Adapter to import video to my macbook pro?
I was wondering if i could use the Apple DVI to Video Adapter to import videos from my camcorder that don't have usb or firewire but have a S-video. to my laptop? and import them to iMovie
Welcome to the Apple Community.
If you mean without internet, then yes, providing it isn't a purchased video (The Apple TV may need to verify authorisation). If you mean without a network, then no. -
Used Mac Mini and reinstalling OS X
I bought a used Mac mini (late 2009) with mountain lion installed. The previous owner didn't do a factory reset, so I attempted to by using OS X Utilities and reformatting the hard drive. I then attempted to reinstall OS X, but since I'm not the original registered owner, I can't get past the login dialog during the license verification stage. What should I do at this point?
Any suggestions would be greatly appreciated. Thanks!The first thing to do with a second-hand computer is to erase the internal drive and install a clean copy of OS X. You—not the original owner—must do that. Changes made by Apple over the years have made this seemingly straightforward task very complex.
How you go about it depends on the model, and on whether you already own another Mac. If you're not sure of the model, enter the serial number on this page. Then find the model on this page to see what OS version was originally installed.
It's unsafe, and may be unlawful, to use a computer with software installed by a previous owner.
1. If you don't own another Mac
If the machine shipped with OS X 10.4 or 10.5, you need a boxed and shrink-wrapped retail Snow Leopard (OS X 10.6) installation disc from the Apple Store or a reputable reseller—not from eBay or anything of the kind. If the machine is very old and has less than 1 GB of memory, you'll need to add more in order to install 10.6. Preferably, install as much memory as it can take, according to the technical specifications.
If the machine shipped with OS X 10.6, you need the installation media that came with it: gray installation discs, or a USB flash drive for a MacBook Air. You should have received those media from the original owner, but if you didn't, order replacements from Apple. A retail disc, or the gray discs from another model, will not work.
To start up from an optical disc or a flash drive, insert it, then restart the computer and hold down the C key at the startup chime. Release the key when you see the gray Apple logo on the screen.
If the machine shipped with OS X 10.7 or later, you don't need media. It should start up in Internet Recovery mode when you hold down the key combination option-command-R at the startup chime. Release the keys when you see a spinning globe.
Some models shipped with OS X 10.6 and received a firmware update after 10.7 was released, enabling them to use Internet Recovery. If you have one of those models, you may not be able to reinstall 10.6 even from the original discs, and Internet Recovery may not work either without the original owner's Apple ID. In that case, contact Apple Support, or take the machine to an Apple Store or another authorized service provider to have the OS installed.
2. If you do own another Mac
If you already own another Mac that was upgraded in the App Store to the version of OS X that you want to install, and if the new Mac is compatible with it, then you can install it. Use Recovery Disk Assistant to prepare a USB device, then start up the new Mac from it by holding down the C key at the startup chime. Alternatively, if you have a Time Machine backup of OS X 10.7.3 or later on an external hard drive (not a Time Capsule or other network device), you can start from that by holding down the option key and selecting it from the row of icons that appears. Note that if your other Mac was never upgraded in the App Store, you can't use this method.
3. Partition and install OS X
a. If you see a lock screen when trying to start up from installation media or in Recovery mode, then a firmware password was set by the previous owner, or the machine was remotely locked via iCloud. You'll either have to contact the owner or take the machine to an Apple Store or another service provider to be unlocked. You may be asked for proof of ownership.
b. Launch Disk Utility and select the icon of the internal drive—not any of the volume icons nested beneath it. In the Partition tab, select the default options: a GUID partition table with one data volume in Mac OS Extended (Journaled) format. This operation will permanently remove all existing data on the drive.
c. An unusual problem may arise if all the following conditions apply:
OS X 10.7 or later was installed by the previous owner
The startup volume was encrypted with FileVault
You're booted in Recovery mode (that is, not from a 10.6 installation disc)
In that case, you won't be able to unlock the volume or partition the drive without the FileVault password. Ask for guidance or see this discussion.
d. After partitioning, quit Disk Utility and run the OS X Installer. If you're installing a version of OS X acquired from the App Store, you will need the Apple ID and password that you used. When the installation is done, the system will automatically restart into the Setup Assistant, which will prompt you to transfer the data from another Mac, its backups, or from a Windows computer. If you have any data to transfer, this is usually the best time to do it.
e. Run Software Update and install all available system updates from Apple. To upgrade to a major version of OS X newer than 10.6, get it from the Mac App Store. Note that you can't keep an upgraded version that was installed by the original owner. He or she can't legally transfer it to you, and without the Apple ID you won't be able to update it in Software Update or reinstall, if that becomes necessary. The same goes for any App Store products that the previous owner installed—you have to repurchase them.
4. Other issues
a. If the original owner "accepted" the bundled iLife applications (iPhoto, iMovie, and Garage Band) in the App Store so that he or she could update them, then they're irrevocably linked to that Apple ID and you won't be able to download them without buying them. Reportedly, Mac App Store Customer Service has sometimes issued redemption codes for these apps to second owners who asked.
b. If the previous owner didn't deauthorize the computer in the iTunes Store under his Apple ID, you wont be able to authorize it immediately under your ID. In that case, you'll either have to wait up to 90 days or contact iTunes Support.
c. When trying to create a new iCloud account, you might get a failure message: "Account limit reached." Apple imposes a lifetime limit of three iCloud account setups per device. Erasing the device does not reset the limit. You can still use an iCloud account that was created on another device, but you won't be able to create a new one. Contact iCloud Support for more information. The setup limit doesn't apply to Apple ID accounts used for other services, such as the iTunes and Mac App Stores, or iMessage. You can create as many of those accounts as you like. -
I have recently bought a Mac Mini and tried to pair the new apple wireless keyboard with the Mac but after trying 6 times no luck. What can I do about this?
try this method:
You need at least a USB mouse. If you don't get any option to pair a keyboard, click through the setup until you get to the "Create Your Computer Account" screen, right click in any of the text fields and select Substitutions --> Show Substitutions. From there click on text preferences. The preferences pane will popup and from there you can just click the back button (next to show all) to get to the full preferences menu. Next click on keyboard, then select setup bluetooth keyboard and you're golden. -
Apple DVI to Video Adapter do's and don'ts
I just got the 15" and am using a monitor for extended desktop. I cannot find any description on whether or not the computer and/or monitor needs to be on or off to plug or unplug the DVI to Video Adapter or whether or not it matters. Any steps and best practices or steps or cautions would be appreciated.
TIAI had a MBP core duo for 7 months and always hot plugged the dvi to vga adapter when I was at my desk. I did this every day and other than the occasional times when the software or hardware switch got confused, i found that there was no issue. The OS usually responded to the connection and knew that an external tft had been connected.
I must have done this 100 times or more.
My advice from experience is that you have nothing to worry about. Hot swapping the dvi is fine. -
Operating System is Mavericks and I have no discs, etc. I've tried to add a new admin and delete the old one but everything is asking me for the original password, which I don't have.
Before buying a second-hand computer, you should have run Apple Diagnostics or the Apple Hardware Test, whichever is applicable.
The first thing to do after buying the computer is to erase the internal drive and install a clean copy of OS X. You—not the original owner—must do that. Changes made by Apple over the years have made this seemingly straightforward task very complex.
How you go about it depends on the model, and on whether you already own another Mac. If you're not sure of the model, enter the serial number on this page. Then find the model on this page to see what OS version was originally installed.
It's unsafe, and may be unlawful, to use a computer with software installed by a previous owner.
1. If you don't own another Mac
a. If the machine shipped with OS X 10.4 or 10.5, you need a boxed and shrink-wrapped retail Snow Leopard (OS X 10.6) installation disc from the Apple Store or a reputable reseller—not from eBay or anything of the kind. If the machine is very old and has less than 1 GB of memory, you'll need to add more in order to install 10.6. Preferably, install as much memory as it can take, according to the technical specifications.
b. If the machine shipped with OS X 10.6, you need the installation media that came with it: gray installation discs, or a USB flash drive for a MacBook Air. You should have received the media from the original owner, but if you didn't, order replacements from Apple. A retail disc, or the gray discs from another model, will not work.
To start up from an optical disc or a flash drive, insert it, then restart the computer and hold down the C key at the startup chime. Release the key when you see the gray Apple logo on the screen.
c. If the machine shipped with OS X 10.7 or later, you don't need media. It should start up in Internet Recovery mode when you hold down the key combination option-command-R at the startup chime. Release the keys when you see a spinning globe.
d. Some 2010-2011 models shipped with OS X 10.6 and received a firmware update after 10.7 was released, enabling them to use Internet Recovery. If you have one of those models, you can't reinstall 10.6 even from the original media, and Internet Recovery will not work either without the original owner's Apple ID. In that case, contact Apple Support, or take the machine to an Apple Store or another authorized service provider to have the OS installed.
2. If you do own another Mac
If you already own another Mac that was upgraded in the App Store to the version of OS X that you want to install, and if the new Mac is compatible with it, then you can install it. Use Recovery Disk Assistant to prepare a USB device, then start up the new Mac from it by holding down the C key at the startup chime. Alternatively, if you have a Time Machine backup of OS X 10.7.3 or later on an external hard drive (not a Time Capsule or other network device), you can start from that by holding down the option key and selecting it from the row of icons that appears. Note that if your other Mac was never upgraded in the App Store, you can't use this method.
3. Partition and install OS X
a. If you see a lock screen when trying to start up from installation media or in Recovery mode, then a firmware password was set by the previous owner, or the machine was remotely locked via iCloud. You'll either have to contact the owner or take the machine to an Apple Store or another service provider to be unlocked. You may be asked for proof of ownership.
b. Launch Disk Utility and select the icon of the internal drive—not any of the volume icons nested beneath it. In the Partition tab, select the default options: a GUID partition table with one data volume in Mac OS Extended (Journaled) format. This operation will permanently remove all existing data on the drive.
c. An unusual problem may arise if all the following conditions apply:
OS X 10.7 or later was installed by the previous owner
The startup volume was encrypted with FileVault
You're booted in Recovery mode (that is, not from a 10.6 installation disc)
In that case, you won't be able to unlock the volume or partition the drive without the FileVault password. Ask for guidance or see this discussion.
d. After partitioning, quit Disk Utility and run the OS X Installer. If you're installing a version of OS X acquired from the App Store, you will need the Apple ID and password that you used. When the installation is done, the system will automatically restart into the Setup Assistant, which will prompt you to transfer the data from another Mac, its backups, or from a Windows computer. If you have any data to transfer, this is usually the best time to do it.
e. Run Software Update and install all available system updates from Apple. To upgrade to a major version of OS X newer than 10.6, get it from the Mac App Store. Note that you can't keep an upgraded version that was installed by the original owner. He or she can't legally transfer it to you, and without the Apple ID you won't be able to update it in Software Update or reinstall, if that becomes necessary. The same goes for any App Store products that the previous owner installed—you have to repurchase them.
4. Other issues
a. If the original owner "accepted" the bundled iLife applications (iPhoto, iMovie, and Garage Band) in the App Store so that he or she could update them, then they're irrevocably linked to that Apple ID and you won't be able to download them without buying them. Reportedly, Mac App Store Customer Service has sometimes issued redemption codes for these apps to second owners who asked.
b. If the previous owner didn't deauthorize the computer in the iTunes Store under his Apple ID, you wont be able to authorize it immediately under your ID. In that case, you'll either have to wait up to 90 days or contact iTunes Support.
c. When trying to create a new iCloud account, you might get a failure message: "Account limit reached." Apple imposes a lifetime limit of three iCloud account setups per device. Erasing the device does not reset the limit. You can still use an iCloud account that was created on another device, but you won't be able to create a new one. Contact iCloud Support for more information. The setup limit doesn't apply to Apple ID accounts used for other services, such as the iTunes and Mac App Stores, or iMessage. You can create as many of those accounts as you like. -
Hi,
I'd be really grateful if someone could help me with this as its beginning to drive me insane!! I have a mac mini 10.5.8 and an iphone 4 that I would really like to synchronize which I understand I have to do through icloud. But, from what I can see I need to be running Mountain Lion but cannot get that until I have Snow Leopard (which I cannot find where to download through the apple website!). I have upgraded my memory to 4GB which I hope is sufficient but just need someone to give me some instruction on what to do next. Any help really appreciated as I desperately need to synchronise my calendars!!Hello, since I have no iPhone I was waiting for somebody else to answer, but I can answer it turns out after finally looking!
First you need to research all the problems people are having with the higher OSX versions, & make sure you have a bootable clone of what you have just in case.
then you must get 10.6 if they still have it, install it & update to 10.6.8 so you have the App Store to buy & download the huge 10.8 Installer.
Snow Leopard/10.6.x Requirements...
General requirements
* Mac computer with an Intel processor
* 1GB of memory (I say 4GB at least, more if you can afford it)
* 5GB of available disk space (I say 30GB at least)
* DVD drive for installation
* Some features require a compatible Internet service provider; fees may apply.
* Some features require Apple’s MobileMe service; fees and terms apply.
Which apps work with Mac OS X 10.6?...
http://snowleopard.wikidot.com/
It's been pulled from the online store & Apple Stores, so you have to call Apple to buy it, last I heard.
Call Apple Sales...in the US: 1-800-MY-APPLE. Or Support... 1-800-275-2273
Other countries...
http://support.apple.com/kb/HE57 -
2011 Mac Mini and Acer x222w monitor incompatible? HDMI to DVI adapter issue
I am totally bummed because I just bought a new Mac Mini thinking I'd be able to use the display from my old system, an Acer x222w, which has both DVI-D and VGA connections. I hooked the monitor up using the HDMI to DVI adapter included in the box with the Mini. On boot, I could see the Apple logo, though it was not centered, and when the set up screen came up to the select language screen, it flashed quickly and then turned to snow.
I was on the phone with Apple support for over an hour trying to troubleshoot this issue. I was a little disappointed that tech support didn't even seem to be aware that the Mini came with an HDMI to DVI adapter. It was then recommended that I try an adapter for the mini display port, which the 2011 Mini doesn't have.
I was able to borrow another monitor, a Dell with DVI-D, and it worked.
I have searched for specs/requirements that might explain why the Acer monitor doesn't work while the Dell one does. I cannot find anything from Apple. I just assumed any DVI connection would work. Has anybody else encountered this problem? Most of the issues I've found on the forums involve trying to hook up to a home theater LCD TV, which I'm not trying to do. If I had known my monitor wouldn't work, I probably would have just saved up for an iMac.
Thanks in advance for any thoughts or tips!Try resetting the SMC andNVRAM
Intel-based Macs: Resetting the System Management Controller (SMC)
About NVRAM and PRAM
Next call Apple since yo have 90 days of free telephone support
Complimentary Support (USA) -
I have a new Mini and updated software. My monitor will keep flashing back and forth, shrinking the display and not allowing me to work. Sometimes clicking the mouse helps, sometimes clicking into the screen but it freezes up and won't allow me to work. Is this a monitor problem or is there some bug in my system.
Try just holding down on the power and home buttons to restart it. Thomas R. doesnt know what he was talking about. The tool is not made for jailbraeking and is not related to jailbreaking. If you want to get the link again, let me know, as I reapir iPhones, have been using it for years, nad it does NOT void your warranty. It simply reboots your device.
My apologies for all of the new people on this site who are novices to anything beyond iTunes or the device itself. Hopefuly your problem is solved.
Maybe you are looking for
-
I'm newly switched to Logic from Cubase. Question on using folders properly! If I drag say 6 guitar tracks from the bin in to the arrange page. Then select all those new regions/tracks and 'pack' them in to a folder. I'm left with a bunch of newly cr
-
I received an email about my credit card information from apple. How do I find out if this is a legitimate email from apple? I can't find an email address for apple so I can ask a simple question....so frustrating...
-
i have a 3g iphone & a pioneer avic-d3 car reciever...the bluetooth unit pairs with the phone anwsers and dials, auto connects, no problem...until today it won't connect with my voicemail as it stays connected...i have the latest up grade on the ipho
-
Hi, The title is rather self-descriptive, but I'll elaborate a bit anyway. I'm receiving data from a local proxy service in and performing validation on it. After validation,the data has to be transformed into two target formats, i.e. the validating
-
Removing host name from jsessionid
We have a standard installing of IWS 6 and the host name is included in the jsessionid even if not configured in wep-apps.xml (we are using the default wep-apps.xml and there is no session-cookie tag in the file. Doc says you have to set session-cook