Using more then one Airport on a WIRED network

The area I want to cover is quite large and it looks like I will need 3 airports to get the coverage I require. Fortunately I already have a WIRED infrastructure to attach them to.
I am just not clear on how to configure them. Do I want to setup the main one to "create a wireless network" and the others to participate in the wireless network, or do I want to set them up to extend the range of the network etc.
I had previously played around with a little bit of this when I didn't have the wired infrastructure in place and was trying to extend the range wirelessly.
Thanks

From your description, you want to create a "roaming network". In that configuration, all your base stations wireless modes should be set to "create a wireless network" with the *exact same network name and wireless encryption*. Leave their radio channel selection and radio modes set to "automatic" until you have reason to change them.
For connection sharing, the one connected directly to your internet gateway will "share a public IP address" and its WAN port should be connected to whatever device brings the internet to your site. All the others will be set to "bridge mode (off)". You'll connect all their LAN ports together.
Reference Page 42 of Apple's Apple AirPort Networks guide.

Similar Messages

Is it possible to use more then one apple tv in a network?

Hi communitie,
I would like to have two Apple TV devices un my home network using two different TV's. Is that possible? Has anyone already tried it?

Yes many has it works fine give them different names

HOW DO I USE MORE THEN ONE ITUNES WITH MY IPHONE WITHOUT ERASING MY MUSIC?

I have two different laptops with iTunes on it. I use both of them but my iPhone only works with one iTunes. I plug it into the computer and it says that my iPhone cannot use more then one iTunes. Is there a way I can use both or no?
YES I AM CLICKING MANUELLY ADD SONGS TO MY iPhone.
I just bought my iPhone about a week or so ago.
Please help ASAP.

I clone my library to a portable drive using SyncToy 2.1, a free tool from MS. I run this both at home & work so that I essentially have three identical copies of my library for backup redundacy, any of which I can use to update my iPods and my iPhone. I use iTunes Folder Watch occasionaly in case I've managed to download, for example, a podcast at one location but overwrite the library with a newer copy updated at the other. It can be done but you need to take considerable care...
tt2

Using more then one table/view in same Report

Hi,
I am using Discoverer Plus Version 9.0.4.43.15.
Is it possible to use more then one table/view in a report without the tables/views being joined in any way? It would be like using two different datasets in the same report without the datasets having anything to do with one another. Right now when I select items from the available tab I can only pick tables that relate to one another in some way.
Or is it possible to use more the one table in the same report? Each table using a different query/view/table.
Thanks

Spence,
try following type of query using set operator UNION / UNION ALL:
select col1,col2
from t1
union all
select col1,col2
from t2
If you don't have restrictions then this is the best way.

Can I use more then one apple ID on my computer/osx app store

Hi,
I use my MBP/iMac/ipad/iphone for both business and home. Right now everything is setup to my home apple id (and I have made quite a few purchases with that). With the release of the osx app store and FCPX, my company wants to buy these for my computers. But they want to do this on their apple id. Can I run more then one id on a mac? How can I make this work as I know they will want me to start getting more apps as they are released.

You can have apps from multiple Apple IDs on one Mac. The issue will be that to update Mac apps bought with A ID #1 will require signing into A ID #1 in the MAS. And later when apps bought with A ID #2 need an update you will need to sign into A ID #2 in the MAS to update them. If you can keep that straight and can abide that requirement, there should be no issues.
The same will be true to update iOS apps, but using iTunes.

Using more then one Multitouch.inputMode on one screen

Hi All,
I have figure out that on one screen I am not able to work with more then one Multitouch.inputMode. As per my requirement I am having two different component on the same screen,one is using the TouchEvent and another is using GestureEvent.I am getting the issue that if I am using both on the same screen then the GestureEvent is not firing.
Any help will be appricated.
Thanks in Advance.
With Regards,
Shardul

Or you could use gestouch:
https://github.com/fljot/Gestouch
With that you can detect various gestures all in one gesture mode. It may solve your issue.

Using more then one null in a Set

Hello Friends,
Can any one throw some lights for using the null values in Set.
Can a set cantains more then one null values? It worls fine if there is only one null element alone but throwing exception if there are any other element with one null.
Thank you.
Roshan

So when you read the documentation for TreeSet.add(), which you obviously did because it's so obvious that you should read the relevant documentation before posting questions, what did you not understand?
Adds the specified element to this set if it is not already present. More formally, adds the specified element e to this set if the set contains no element e2 such that (e==null ? e2==null : e.equals(e2)). If this set already contains the element, the call leaves the set unchanged and returns false.
Throws:
NullPointerException - if the specified element is null and this set uses natural ordering, or its comparator does not permit null elements
Edit: By the way, there was a recent thread about the fact that it appears that Java 5 had a bug in which when you add the first null, it didn't throw an NPE, but in Java 6 it did. That may be relevant information depending on what JRE you're using.
Edited by: endasil on 9-Dec-2009 1:31 PM
Edit 2: Here's a (or the) bug report: [http://bugs.sun.com/view_bug.do?bug_id=5045147]
Edited by: endasil on 9-Dec-2009 1:34 PM

How do you use more then one computer for your Ipod??

One of my computers died and I want to still use iTunes to get more music but I don’t want to erase what I have on my iPod now. I need to use a different computer with out erasing all the music I have now?? HELP

If your iPod is set to update automatically you need to take care connecting to a different iTunes. You can use a keyboard command to prevent your iPod auto-syncing with iTunes. While connecting the iPod to the computer on Windows with iTunes 7.3 or later installed hold down the Shift + Ctrl keys together. This will stop the iPod from auto-syncing with iTunes and the iPod will appear in the source list. Wait until you are sure the iPod has mounted, and that it will not auto sync and then you can let the keys go. This may take between 20 to 30 seconds depending on your computer: iTunes - Keyboard Shortcuts for Windows
When your iPod appears in the iTunes source list change the update setting to manual. If you want to connect and use an iPod on more than one computer you need to change the update preference in the iPod Summary tab to "Manually manage music and videos" and click Apply. The content of iTunes and the iPod are not syncronised in this mode so the two can be different. You can directly access the content of the iPod and play it through iTunes and you can drag and drop whatever you want to the iPod from either library:
Using iPod with Multiple computers
Managing content manually on iPod
Syncing Music to iPod
Something else to be aware of when using an iPod in manual mode is that the "Do Not Disconnect" message will remain on the display until you physically eject the device: Safely Disconnect IPod

Can i use more than one airport express to extend the airport extreme?

my house is too big, and i use one airport express to extend my network,but the other half of the house doesnt get access to the internet.The question is can i use another airport express, without any complications?

Yes, up to 255 if I remember correctly. But before you do that take a look at the products offered by QuickerTek to amplify the output power of a router and/or add gain antennae to help increase the router's range without the need for adding access points.

Using more then one computer but only see new songs on one computer

I have my itunes on both my home computer and my work computer and when I purchase new music on my home computer it doesnt show up on my work computer. How can I see the music on both?

*I purchase new music on my home computer it doesnt show up on my work computer. How can I see the music on both?*
If you want to have your purchases on more than one computer you have to copy them from the computer they are purchased on. When you purchase something it is downloaded to the computer you are logged into at the time, purchases don't simply appear on ever computer you choose to use. There are various methods to copy purchases between computers, CD-R, iPod, USB stick etc, you can read more at this llink: iTunes for Windows: How to copy purchases between authorized computers
You can have up to 5 computers authorised at any one time to play iTunes purchases: About iTunes Music Store Authorisation and Deauthorisation

How to use more than one airport express with multiple speakers

I have 2 Airport Express. Prior to the multiple speaker enhansement I changed spekers by changing the wireless network. Each of the Airports is recognised as a wirelss network. Is there any way I can make my computer and itunes to see all of my Airports so I can use the Multiple Speaker function for both of my Airports at the same time withour having to change wireless network.

You need to have a single wireless network.
If you con't have a wireless router, then you will need to configure one of the Airport Express (AX) units to join the existing wireless network of the other AX.

Can I use more than one AirPort Express to deal with access problems on my system?

my house unfortunately has wall-boards which have a layer of tin foil on them, which is great when you are looking for cheaper heating bills, but is absolutely awful when trying to install Wi-Fi!

Yes you can, you could either run cat 5 cable to each one and have them as seperate wii networks or do as I do and use the as range extenders.
See http://www.apple.com/uk/airport-express/
Extend an existing Wi-Fi network’s range.
If you already have a wireless network in your home and want to extend its range,AirPort Express can help. Just place it in range of your primary base station — anAirPort Extreme, AirPort Time Capsule or another AirPort Express — and near the area where you want your wireless connection. Launch the easy-to-use AirPort Utility app on your iOS device or Mac, and you’re mere minutes away from long-range Wi-Fi enjoyment.

How to utilize more then one airport connection

I am on an ethernet, wireless usb, and wifi. I want them to work together and not be connected to all but only using one. How can I do this

Hi vinod,
Call one BDC after the another, Like if u want to create a sales order and then correspondingly display it as well, u can capture the sales order created afer ur first BDC theu the messages mostly in SYMSGV1 and using this u can do a call txn skip first screne of VA03.
If u are talking about session, get 2 session names and move them to different sessions or if both txn are dependant on each other, move it one after the other thru call txn. It is the same, howmany ever trx u wabnt to post thru BDC.
Award points if this helps.

ORA-19228: XPST0008 -- undeclared identifier when using more then one var.

HI Gentlemen,
Given an XMLTYPE table with only one row. Under the root element there is a <header> and a <body> where the stuff inside the body has a different namespace. When I try to drill down with the statement in p.sql below, I always get
SQL> @c:\xsl\p
FROM z
FEHLER in Zeile 10:
ORA-19228: XPST0008 - nicht deklarierter Identifier: Präfix 'j' lokaler Name '' (undeclared identifier)
I also tried to insert a WHERE clause, it always complains with $j. When I am using only one variable, $i, it is OK. XML DB Developer's Guide has examples that are very close to this--they execute A1. CAn you help me where am I wrong?
Thank you very much, kind regards
Miklos HERBOLY
SELECT
   XMLQuery('xquery version "1.0"; (: :)
   declare namespace n1="urn:ehd/001"; (: :)
   declare namespace n2="urn:ehd/go/001"; (: :)
   for $i in /n1:ehd/n1:header
let $j := /n1:ehd/n1:body/n2:gnr_liste/n2:gnr
   return $i,$j'
   PASSING xml_document
   RETURNING CONTENT) as ziffer
FROM z
/

Hi Miklos,
You'll need parentheses to indicate that you're returning the sequence of $i and $j :
xquery version "1.0"; (: :)
declare namespace n1="urn:ehd/001"; (: :)
declare namespace n2="urn:ehd/go/001"; (: :)
for $i in /n1:ehd/n1:header
let $j := /n1:ehd/n1:body/n2:gnr_liste/n2:gnr
return ($i, $j)or shorter version (if there's only one header per document) :
xquery version "1.0"; (: :)
declare namespace n1="urn:ehd/001"; (: :)
declare namespace n2="urn:ehd/go/001"; (: :)
/n1:ehd/n1:header
, /n1:ehd/n1:body/n2:gnr_liste/n2:gnr
)

Performance degrades using more then one Textfield

Hi everyone,
I noticed that performace in my app degrades noticeably when there is more than a Textfield on stage. I need to have two dynamic text field displayed at the same time, which is the best way to achieve this without using too much processing power?
Thanks.

I'm testing on the first Iphone model. Basically when the user put some information in two input field the input field disappear, the background change and some dynamic text is displayed. This happen with a fade out effect done playing with the alpha of a white bitmap. I know I shouldn't use alpha property but performance are still fine if a insert only a text field it start to slowdown only with two so I was hoping some tuning on text fields could help me to avoid this.
I just discovered that if a cache text field as Bitmaps i fix the speed issues but text changes color in a light blue, I really don't know why

Using more then one Airport on a WIRED network

Similar Messages

Maybe you are looking for