Using movement type 551 in Production Order

Hi all
I want to do a mvt type 551 of components to the Production order but it allows me only a 261 movement type. Is there a way we can do that.
thanks

Hello John,
  551 is a transaction for scrapping inventory against a cost center. In a way, 261 is doing the same txn by moving inventory from stock to Process order.
  Why are you trying to perform a 551 against a process order? There might be another solution to the business issue.
Regards,
Anand

Similar Messages

  • Movement type 551 account posting in Balance sheet account

    Hi Team,
    I got a requirement for the specifically as below.
    ->   set the automatic account assignment for the 551/ 552 to be a balance sheet account rather than cost center or profit center..
    What changes need to enter into the configuration.
    Note - If required, will create separate movement type taking reference of 551, and do the required changes.
    \\ Shankar kumar

    When you use movement type 551 or 552, System will always hit the transaction key GBB and BSX.
    Account modifier for GBB is defined on the combination of OBYC and OMJJ transaction.
    We know we use balance sheet G/L account for transaction event key BSX and PL statement G/L account for GBB - Off settings transaction event key.
    Here you can use the Balance sheet G/L account for the transaction event key GBB and account modifier as per your requirement.
    I suggest do not use standard movement type. Leave the standard movement type for standard process.
    As this is exceptional case, please create a new movement type by coping 551 or 552. Then change the account modifier.

  • Single Report for production scrap and Movement type 551 scrap

    Hi All,
    Can we include the scrap information from production and scrap from movement type 551 into a single BW report?.......My assumption is we cannot include it into a single report coz production scrap will have a different material information and scrap from movement type 551 will have a different material information..please correct me ig i am wrong......
    Regards,
    Shravani

    hello,
    you can have a single report by two options
    1. have a variable on movement type.If you choose 551..U will get materials of tht movt type.
    also if the select teh movt type for prodcution, it wil display its materials.
    or
    2. U have to place  movt type in the rows.Place movt type and then material in the rows.
    Then u will get for each movt type..its corresponding materials.No variable selection needed here.
    Regards,
    Dhanya

  • Automatic Transfer Orders movement type 551

    Dear All
    I am working on warehouse management Transfer Orders for movement type 551,
    please suggest me what kind of  parameter need to select for movement type 551,553,555 in order to create the automatic transfer order in below customisation setting
    Implementation Guide for R/3 Customizing (IMG)->
    Logistics Execution->
    Warehouse Management->
    Activities->
    Transfers->
    Define Movement Types
    551,553,555
    Best luck to all
    Regards
    Nitin

    Dear all
    i got the answer
    i made the small modification in movement type , it is as below
    i flage the field "<b>Manual creation of transfer order not allowed</b>" &
    <b>"Automatic transfer order creation"</b> with value <b>X</b>
    thanks for watching my thread
    cheer's
    nitin

  • Movement type 551

    dear experts
    even though I put the cost center as optional for the movement type 551, in OMB6 and also on the program  RM07CUFA.
    When I do a MIGo and use 551 movement tyype the system is asking for a cost center as a mandatory entry, even though I put Gl acct in the acct assignment on MIGO.
    Please let me know, how can I just scrap material without inputting cost center or a profit center.
    Thank you
    MSJ

    MSJ,
    You are probably encountering a situation where the financial and controlling systems are determining what is required in the posting. 
    The field status group defined to the GL account will determine what is required for financials to post the entry into the GL. 
    Having a cost element assigned to the GL Account in controlling will require a cost object (either cost center, internal order, WBS, etc.) to post the entry into CO. 
    You have three options for setting this up: 
    1)  define a default cost center for the GL account using transaction OKB9,
    2)  setup a substitution rule to determine the cost center for the posting,
    3)  set the automatic account assignment for the 551 to be a balance sheet account.
    Most of my clients have used option 2 above. 
    Cheers!
    Rick

  • Hide Cost Center & GL Account in Movement Types 551-556

    All,
    Requirement - Movement Types 551-556 should not allow the user to see or enter the Cost Center or G/L Account.
    How can I remove the user from having to enter and see the cost center and G/L account fields from movement types 551-556?
    I see I can make them both optional but this does not seem to be working. When I got into MB1A, I am still forced to enter both values. I
    Please advise!
    Thanks!

    He wanted the cost center (or any other account assignment) is to be displayed only but not ready for input in MB1A screen. Then how can user enter the cost object to post the loss. System by design enables user to enter his own GL account (if that GL is configured to the process).
    Automatic account determination helps to identify the correct GL account only for any movement type (say process) but not the account assignment objects like cost center, WBS element, order etc..

  • Can we use Movement Type other than 653

    Hi all
    we are using movement type 653 for material which are being returned by customer.
    we dont want to create FD ( Free of Chagre)  Sales order against the returned delivery.
    Problem
    The Return Delivery is being showed in VLO6  transaction,(outbound delivery),we dont want the return delivery to get displayed in this transaction.Is their any other transaction we can use inplace of 653,in order to get material in unrestricted stock as well as the delivery should not be get displayed in the transaction.
    I have created the new return delivery type (By copying LR) and at the time of runing the T-code VLO6,I exclude that delivery.
    In this way the delivery is not being shown.
    If there is any other way to slove this issue please let me know.
    Thanks
    Siddharth

    The "Return Delivery" is being showed in VLO6
       transaction, "(outbound delivery)"
    Not sure on this.  When you say you created a return delivery, how it is appearing in outbound delivery list.  For information, standard movement types in SD for returns are 651, 653 & 655 and transfer the blocked stock to unrestricted use with movement types like 453, if you wish to do so.
    But strictly speaking, all returns will have to be addressed in QM and only after their clearance, any returned material should be reused.
    thanks
    G. Lakshmipathi

  • Stock Transfer for Excisable Materials Using Movement Type 301

    Hi,
    We are having a Plant 1002 as excisable Materials.
    During GR we following the process like GR (Part -I), Capture Invoice, Post Invoice.
    Can we transfer the Material from Plant 1002 to other Plant, say 1001, using Movement Type 301?
    Or we need to follow some other router for Stock Transfer for the Excisable Materials?
    I was told by the ex-consultant that we would be using Mov Type 301 for all Stock Transfers, but I have a doubt, please guide.*
    Regards,

    Hi PK,
    Here in Brazil we work with excisable material and when we have to transfer it plant to plant, we have to use IVA that performs tax posts on accounting document. Also, we have to create Nota Fiscal (BrazillianLegal Document).
    I think you have to talk to your legal/accounting area in order to make sure which procedure you will have to use.
    If you need tax posting on accounting document, then you will not be able to use 301 movement type.
    We use MM/SD Plant to Plant transfer (movement type 861 / 862)
    Depending on your Legal/accounting area feed back, you could use this scenario or just MM plant to plant transfer (movement type 303/305).
    If they are ok with no tax postings on accounting document, then 301 movement type should be used.
    Try to make a test, show then how it works, then you could get ok from then
    I hope it helps you.
    Best Regards,
    Natan

  • Production Order   : OUTPUT Type Configuration for Production Order  as EDI

    Dear SDN All ,
      OUTPUT Type Configuration for Production Order.
    <b>Doubt in third Point</b>
    We have found the IDoc " LOIPRO01 " for Production Order
    (Please confirm that this IDoc can be used for outbound IDoc for Production Order)
    And foloowing
    <b>1. Defining the Output Type for Particular Application.
       T-Code: “NACE”</b>
      A. Output type have created upder application "ME" description : "Inventory Management"
      B.  " ZEDI "  created for getting output as EDI type
         ZEDI is copied from "WF01" output type. and
         Transmision mediam as "EDI"          
         Program : RSNASTED
         Form Routine :  EDI_PROCESSING
              (Please confirm is this for IDoc creation)
    <b>2. Partner profile creation:</b>
      A. Partner profile created under logical system and
      B. and In outbound parameter declared as "LOIPRO"(This is for sending the IDoc "LOIPRO01" to XI system).
    <b>3. Customization for output type for Proction Order -- (For CO02,CO08)</b>   ---
       A. But only one functional customization is remaining to do, for getting the IDoc while saving the Production Order in T-Code "CO02" and "CO08"
            <i>For Example:
                in sales order transaction va02 (in DBI 450 client) and select any Sales order.
                & select following menu path.
                 Extras --- > Output -
    > Header -
    > output
               Here we can set our output type "that U defined in NACE Transaction-Code"</i>
    <b> Like the same way I want to set output type  for CO02, CO08 transaction.</b>
    But I couldn't find the menu Item in Co02 and Co08 for setting the output.(like VA03)
    Please help me out for setting the output type for Production Order Creation.
    Thanks in advance,
    Dhanabal T
    Message was edited by: Dhanabal T

    Hello.
    I have a similar requirement. Did you guys find the solution?

  • Cost center and movement type 551

    Hi all!
    Can the cost center be determined automaticaly when creating this movement type 551?
    Regards

    Hi Eduardo,
    first of all the field status of the MM movement type (trx. OMJJ) has to allow cost center (set to repuired or optional). Afterwards you can use the CO substitution to determine the cost center.
    Cheers,
    Daniela

  • Hide/Suppress Cost center field in MIGO and MB1A for movement types 551&552

    Hi All,
    Can anybody tell me how to suppress or hide the cost center field in MIGO or MB1A for movement types 551 and 552?
    I did below settings and it worked fine for only MB1A and for MIGO still it is showing cost center field.
    IMG > Materials Management > Inventory Management and Physical Inventory >Goods Issue/Transfer posting > Define screen layout > select movement type to change the option.
    Also I did gothrough the settings for Enjoy transaction (MIGO) there we have only option to make fields either  "Required entry" or "Optional entry" and we don't have an option to hide/suppress.
    Please advise or help me .
    Thanks in advance!
    Regards,
    Praveen

    Hi
    The cost center field is a required field in mvt type 551 as you are scrapping materials, some cost center will need to take the cost of this operation.
    Anyway, you first need to make the field as optional for example, before you move.
    One option is that you create a screen variant in Tcode SHD0 for MB1A, where 551 is setup as constant (with content) , and mark Cost center as invisible and assign this screen variant to a transaction in SE93.
    regards
    Sidi

  • Use Handling Units to group production orders?

    Hello,
    can I use Handling Units to group production orders together? We have a workcenter where all our orders go through and we'd like to group, say, the morning's orders in a single HU on which we could post a single transaction (batch?) instead of posting on each and every order.
    Thanks,
    Jonathan

    Please check OSS note 793168.

  • Sales Returns Stock posting using movement type 651

    Hi Experts,
    I want to upload the sales returns stock using movement type 651. Because, our existing company code 'xxxx' has been changed to 'zzzz' and all the stocks, balances and so on has been uploaded and carry forwarded to new company code 'zzzz'.
    Now, I stuck with the customer/sales returns stock. Also, I know that there is no accounting effects with the movement type 651 i.e., blocked stock stored in customer rejection storage location.
    I have tried lot but I didn't get the solution for the same.
    Kindly share some ideas to upload the sales returns stock.
    Anandkumar KS

    Dear Experts,
    First of all, sorry for late reply.
    I tried using the movement type 655, but i can't able to post the stock.
    Is there any other way to post the stock in customer rejection storage location with the movement type 655?
    Also, it should not create any Accounting Document while posting the stock.
    Please advice me in this issue.
    Anandkumar KS

  • Material to Material Transfer using Movement Type 309

    Hi,
    We have activated the material ledger.
    Issues:
    When we transfer material A to Material B using Movement Type 309 the price difference from Material A was not allocated to Material B after executing CKMLCP.
    But the another company who using the materail to material transfer, the price difference was allocated to receiving material.

    Hi,
    Please check SAP Note 167722 to able to do multi-level price determination for material transfer with using modification.
    best regards, Takashi

  • Restriction to use mov type 309

    Hi,
    I need to restrict  some of users not to use mov type 309 only, other mov type they need to use, in that case how to do ??
    I knew the object (object name -authorization object is M_MSEG_BWA)  pls tell me the steps?

    Dear Jayakumar,
    While creating the roles using T Code PFCG,after adding the T code MB1B under any role,ask your Basis consultant to look for
    this authorization object M_MSEG_BWA,and dont include the check box for 309 movement and include it for the other
    movement's like 311,312 etc.
    So whatever role that's allowing MB1B should be checked so that it 's not having the authorization for 309 movement.
    Check and revert back.
    Regards
    Mangalraj.S

Maybe you are looking for