Using my MacBook Pro as a keyboard for my iPad

I have a old MacBook Pro and a new iPad2.  I am basically barely using my MacBook Pro anymore but I still prefer to type emails and other documents on the full keyboard.  Is there any way make my keyboard from my MacBook connect to the iPad?  I know that I could purchase a wireless keyboard but I feel that there must be a way to do this with my MacBook.  Suggestions?

OS X does not have any built in way to do that. The only way for it to work would be through some third party app (running on your Mac Book) to send the keystrokes out via Bluetooth. I do not think such an app exists, but if it did, it would require your MacBook to be powered up in order to run. Your iPad runs a lot longer than your laptop on a single charge so that might be an issue. I just went to the apple store and bought the Bluetooth keyboard. It is much lighter than a laptop and runs an a couple of AA batteries.

Similar Messages

  • Using my MacBook Pro as the host for projection to my TV via AppleTV?

    Can I subscribe to HBOGO thru Apple TV and avoid cable service using my MacBook Pro as the host for projecting to my TV via AppleTV?S

    Possibly.
    Some sites such as TMN GO which is similar will not allow mirroring to take place.
    It works for about a minute then shuts down... Security settings from the site.

  • Using your MacBook Pro as a Router For the Xbox 360

    Not sure how many of you guys have 360s, but I've written up a guide to use your MBP as a connection point for the 360. Basically it involves sharing your Airport with the Ethernet port. Here goes.
    How to Use a MacBook Pro as an Xbox 360 Internet Hub v.01
    This guide is copyright 2006 Jonathan Ferguson.
    If you would like to host it, email me at the address below.
    All trademarks are copyright their respective owners.
    I am not responsible for anything that happens that may screw up your Mac, 360, Internet, or anything else.
    By reading further you accept full responsibility for any damages or troubles that occur as a result
    of your using this guide. K?
    Welcome! I recently purchased a MacBook Pro and did not feel like shelling out 130 dollars for the
    360s Wireless Adapter.
    Thus I set out to find a solution and it was my shiny new mac that came to the rescue.
    I'm positive this can be done in Windows, but I've not taken the time (yet) to test it.
    I think it's very simple to follow, but I do recommend that only those with patience and a will to learn attempt the setup.
    Also if you don't know how to reset your router, I wouldn't recommend it either. But for the rest, on we go.
    You will need these things for this adventure:
    Broadband Internet Access
    1 Xbox 360
    1 CrossOver Cat 5 (NOT Patch, so NOT the one that came with the 360)
    1 Macbook Pro (the regular Macbook may work, I haven't tested it)
    1 Router with wireless and wired connections or 2 Routers linked together, one wired, one wireless.
    Plug the cross cable into the ethernet port on the mac and the ethernet port on the Xbox 360. Turn both on.
    Go to your system blade on the 360 into the network settings and go to the Sharing area of the
    System Preferences on the MBP.
    On the MBP make sure that your Airport Extreme connection is being shared with the Built-In Ethernet
    (check the box next to Built In Ethernet and hit the start button at the top.).
    Go into Network under System Preferences on the MBP.
    Pick Built In Ethernet in the Drop Down menu. Write down the Subnet Mask and IP Address for the adapter,
    you'll need that later.
    Contact your router by punching it's IP into an internet browser. (I.E: 192.168.1.1).
    This is usually the default IP for any router, so if you don't know what it is, try that one.
    It'll also ask you for the password and username which are usually:
    Login: admin
    Pass: password
    Login:
    Pass: admin
    or
    Login: admin
    Pass:
    Once you're in find the DNS Addresses (DNS 1 and 2)
    (under LAN not WAN if they're different) and write those down. Now it's time to go back to the Xbox.
    In the settings tab you'll find a lot of stuff has been set to automatic.
    This will not help you, so start changing the things to manual.
    Once you get in there, input each piece of information like so:
    IP Address: Have a look at the address of the Ethernet Adapter.
    Copy it digit for digit only make the last number lower than the last number of the Ethernet Adapter.
    (I.E if the Adapter is 111.211.13.5, make the 360 111.211.13.4)
    Subnet: This is the Subnet Mask you got from the Ethernet Adapter.
    Gateway: This is the IP address of the Ethernet Adapter (NOT the address of your router)
    DNS: These are the DNS numbers you got from your router.
    Now, before you allow the Xbox 360 to test the connection, make sure that you have a
    wireless internet connection coming in on the mac, and that you're sharing it with the ethernet card.
    Also, though I haven't tested it yet, keep the Ethernet card on DHCP. Putting it on manual might mess things up.
    Et Voila! Let the 360 run the tests.
    There's one test that'll take extra long to do but don't fret, it eventually goes through and works splendidly.
    I'll update this as I see fit, and feel free to email me at: [email protected] to add/correct/contribute.

    Well that's nice and all, but why not just spend the 50 bucks on a router? Also, why do you need a crossover cable? Modern operating systems do not require crossovers anymore.
    ~David

  • Is there anyway to use the macbook pro as a moniter for a seperate device?

    Is it possible under a program of some sort to use the macbook pro's screen as a seperate moniter for a device because I am always on the go and I bring my macbook everywhere so it would be extremely conveniant if I could use it's amazing screen as a moniter for: dvd player,xbox,ps3,etc.

    darrylji wrote:
    if I could use it's amazing screen as a moniter for: dvd player,xbox,ps3,etc.
    Macbook Pro's have dvd players built in.  Is yours broken?  Yes, you can hook up an xbox 360 or a ps3.  google provides several articles and video tutorials on how to accomplish this.

  • Is is possible to use the MacBook pro as a handsfree for the iPhone?

    Why we cannot control de iPhone using the MacBook pro?.
    It should be very easy, but it is not.
    I even can't pair my MacBook pro with my iPhone, see pic!
    I really do not understand why we can not use the MacBook bluetooth capabilities to make calls, answers calls etc.
    Apple let us use the Mac bluetooth capabilities to use and control our iPhone, it should be easy, also!

    You may think it should be easy, but in reality it is not.  Your MacBook Pro is not a dedicated handsfree headset, and it would take a considerable amount of effort to write the application code to create a program for your MBP to emulate one.  You can find any third party developer you like and convince them to create a Mac App for you which will provide you with a user interface on your Mac, and use Bluetooth to emulate a handsfree headset for your cell phone (it swouldn't even have to be an iPhone) and see just how much they want to charge you for such an application.  You might be surprised to see how high those numbers really are...

  • Can you use a MacBook Pro without the keyboard attached?

    Hi,
    I plan to upgrade the hard drive in my MacBook Pro (MBP) to a solid state drive (SSD). I also plan to remove the SuperDrive in the optical bay.
    I have to install a new firmware on the SSD. Installing the firmware requires the SuperDrive.
    I intend to remove the SuperDrive after installing the firmware. I'm using a Early 2008 MBP (Pre-Unibody). This MBP is a difficult to dismantle and assemble.
    Can I run the MBP (to install the firmware in FreeDOS) without reattaching the top panel (which houses the keyboard). Or can I just lay the top panel on the MBP without screwing it down. Will either of these actions damage my MBP? Once I've installed the firmware on the MBP, I'll reattach the keyboard.
    I don't want to dismantle the MBP (to insert the SSD), assemble the MBP (to install the firmware with the CD in the SuperDrive) then disassemble the MBP again (to remove the SuperDrive).
    I'd rather dismantle and assemble the MBP once.
    Lifting the top panel (which houses the keyboard)
    [IMG]http://s1.guide-images.ifixit.com/igi/AWVpQDJmt36GHxMS.large[/IMG]
    [IMG]http://s1.guide-images.ifixit.com/igi/CRBYPZtYRqpWYY4O.large[/IMG]
    Please let me know.
    Thanks!

    Sorry, Just noticed you were not using the Unibody models.
    I am unaware if the power button is dedicated. Seems like you're on the right track with iFixIt. I figure as long as USB is available, it should be okay.

  • Pre-ordering Macbook Pro with Norwegian keyboard for US pickup - possible??

    If I pre-order/pre-pay a new Macbook Pro (Retina) for pickup in the US, is it possible to get it fitted with a norwegian keyboard? When buying online I only see the options for English, Spanish and French keyboards.

    Well, there not really any way I can in direct contact with them without calling them, which is not an option for me where I'm currently based. The potential pick-up stores themselves do not have emails listed on their page either..
    Is there any official helpline from apple which is email-based??
    Alex.

  • Macbook Pro into Bluetooth Keyboard?

    I know the hardware is all there, how do I turn my macbook pro into a keyboard for my blackberry?

    Read here  >  Supported Bluetooth Profiles
    http://support.apple.com/kb/HT3647
    Note:  The Sync process is via iTunes
    See here  >  http://support.apple.com/kb/HT1386
    From Here  >  http://www.apple.com/support/iphone/syncing/

  • Is there a list of keyboard shortcuts for Win 7 using the MacBook Pro keyboard ?

    Is there a list of keyboard shortcuts for Win 7 using the MacBook Pro keyboard ?

    See > http://support.apple.com/kb/HT5636

  • Mid 2010 MacBook pro took a keyboard spill.  It still works but display is sooo dark - like no backlight.  I think this is an LED screen.  Does anyone know the fix for this?

    Hi all...  My mid 2010 MacBook Pro took a keyboard spill.  It still works but the display is very very dark.  A faint image can only be seen at an angle in very bright light.  I think this model has an LED screen.  Can anyone please tell me what the fix for this is?  Thank you sooooo much! 
    < Email Edited By Host >

    Spill Cleaning
    Some liquid has just spilled into your Mac. What should you do?
    Do
    Immediately shut down the computer and unplug the power cord.
    Remove the computer's battery (if you can)
    Disconnect any peripherals (printers, iPods, scanners, cameras, etc.)
    Lay the computer upside down on paper towels to get as much liquid as possible to drip out.
    Note what was spilled on your Mac.
    Bring the computer into an Apple store or AASP as soon as possible.
    Don't
    Don't try to turn it back on. Liquids can help electrical current move about the components of your Mac in destructive ways.
    Don't shake the computer (this will only spread the liquid around).
    Don't use a hair dryer on it (even at a low setting a hair dryer will damage sensitive components).

  • Using the MacBook Pro with external Monitor and Keyboard

    This may be a dumb question, but here it goes anyway:
    Can I use the MacBook Pro with an external monitor and a bluetooth keyboard and mouse without having it opened all of the time ?
    I am planning to buy a MacBook for my wife and most of the time she will be using it at her home office.
    I don't want her to use the computer opened all of the time when she is actually looking at the separate screen and using a separate keyboard. Having the laptop opened will only accumulate dust and reduce the lifetime of the built in screen.
    What I would actually need is a kind of "docking station", but Apple doesn't make that - I know.
    So can the MacBook at least be operated without the internal screen powered on while it is closed?
    Thanks for your help
    Martin
    Message was edited by: mdopp

    Yes - it's called clamshell mode:
    http://support.apple.com/kb/HT3131

  • Can i use a macbook pro keyboard with lighted letters with my macbook early 2008

    i need answers!!!!!!can i use a macbook pro keyboard with lighted letters with my macbook early 2008

    No, the MacBook does not have the hardware on the logic board needed for the lighted keyboard.

  • How do I use my Macbook pro retina display as a monitor for a PC?

    How do I use my Macbook pro retina display as a monitor for a PC?

    MacQueries wrote:
    How do I use my Macbook pro retina display as a monitor for a PC?
    Unfortunately, that is not possible. The computer only can "output" your display image, it cannot "input" an image from an external computer and display it on your MacBook's retina display.

  • I am trying to connect a Macbook Pro to a projector for a Powerpoint presentation. When I use a VGA cable, the color of the projected images are not good. When I use a USB cable, the projected image includes the presenter notes on my computer screen?

    I am trying to connect a Macbook Pro to a projector for a Powerpoint presentation. When I use a VGA cable, the color of the projected images are not good. When I use a USB cable, the projected image includes the presenter notes on my computer screen?

    To move an iPhoto Library to a new machine:
    Link the two Macs together: there are several ways to do this: Wireless Network,Firewire Target Disk Mode, Ethernet, or even just copy the Library to an external HD and then on to the new machine...
    But however you do choose to link the two machines...
    Simply copy the iPhoto Library from the Pictures Folder on the old Machine to the Pictures Folder on the new Machine.
    Then hold down the option (or alt) key key and launch iPhoto. From the resulting menu select 'Choose Library'
    and select the Library that you moved.  That's it.
    This moves photos, events, albums, books, keywords, slideshows and everything else.
    Your first option didn't work because you imported one Library to another. Every version and thumbnail is imported like a distinct photo, you lose all your Albums, Keywords etc., the link between Original and Previews is destroyed, the non-destructive editing feature is ruined and so on. In summary: it's mess.
    Your second option didn't work because you simply referenced her library on the old machine.
    Regards
    TD

  • I'm using a macbook pro, running snow leopard. Yesterday I got around to emptying my trash for the first time in quite awhile and was surprised by how much there seemed to be in there. Immediately after a question mark symbols appeared on all my hard disk

    I'm using a macbook pro, running snow leopard. Yesterday I got around to emptying my trash for the first time in quite awhile and was surprised by how much there seemed to be in there. Immediately after a question mark symbol appeared on all my hard disk folders. If I click on these question marks I get a message saying ' the item can't be found'.

    mpagan47 wrote: a question mark symbol appeared on all my hard disk folders.
    Not sure where these hard disk folders are located that you are referring to?  Finder, Finder tool bar, Finder side bar, Desktop, Dock? 
    More then likely they are  an alias that not longer point to the orginals,  thus the question mark.
    I would reboot.  Delete icons if an alias and just recreate by dragging from the source. Try right click (control) click to remove.

Maybe you are looking for

  • Inconsistency when appending a table

    hi i did an append in a standard table because of some requirement lets say i append with field name XXXX but when i go the se11 and input xxxx NE space (this should return me all field where xxxx is empty) i get 30 record and when i go the SE11 and

  • XPath expressions in XmlCursor / XmlObjects

    Hi all, I tried to get a portion of an XML by using XPath Expressions as follows: String xPathExpression = "declare namespace xq='http://inti.notariado.org/indices' " + "$this/xq:RULES/xq:RULE[@disabled]"; A simple example of an xml <rules> <rule dis

  • Which version of Adobe Photoshop works with OS X 10.8?

    I just switched from a Windows PC to a new iMac and I need to get another copy of Photoshop CS for Mac.  Does anyone one know which version(s) will work with OS X 10.8?  Thanks for your feedback - I don't want to spend a lot of money on the wrong ver

  • Why are there changes in the histogram with a convert to profile?

    When you convert an image to a different profile the color numbers change, in order for the colors to represented the same (as closely as possible given the gamut differences) in the new color space.  The histogram also changes, quite noticeably.  Wh

  • I want text to pop up over a link.

    I want text to pop up when a mouse hovers over a link I've created in a PDF using Acrobat 9.  This should help explain the link.  Can someone help me figure out how to do that?  Thank you in advance for the help.