Using my PC as a "Router"

I currently have wifi and my main desktop PC is nowhere near the router.  My PC gets on wirelessly and it shares internet connection with the other devices near it via crossover cable (one end plugged into a PC and the other plugged into a switch, which the other devices get internet from.  On the windows side I just shared the wireless connection and that was good enough to get it working.  I have yet to get a similar setup working in arch.  I was looking at this link:
http://wiki.archlinux.org/index.php/Internet_Share
Will that work if it's PC to switch as opposed to PC to PC?  I'm currently notn near the machines in question so I thought I'd get some opinions before I go home and try it.

Well switches dont really do much so yeah it will work, its pretty much what windows does. That guide is pretty basic, is your PC directly connected to the internet or to a router?

Similar Messages

  • How do I use AO update in the Route signal.vi

    Hi support,
    My goal is to create a waveform (to buffer it) and output it using the analog card (PCI-6713) N times and with the frequency F. Apperanlty this is done using a (actually 2) digital counter(s) on the PCI-6602 card.
    This is done using route signal.vi using "AO update". However I have not managed to get it working. I only get error -10341. So my questions are how do I do it? More specificly how do I use AO update in the Route singal.vi Do I need to conect the cards in any perticular way (cabels or so)? Also do you have more information about how the vi route signal works (the help file does not help me much)?
    Grateful for all help.
    I'm using labview 6.0 as developpement platform, and using the PCI-6601, PCI-67
    13 and a PCI-7344 cards. Since the program is quite large I will only send a portion of it, the pulseGen is supposed to generate the waveform (loaded as a text file, also submitted) the digital output used is in case 1 (in pulseGen) the analog output is in case 3. The MissingWaveform.vi is just to ensure that a waveform is supplied to the pulseGen.vi
    Sorry about the mess.
    /Chatri

    Cabling and Interfacing between Boards: You have capability for direct simultaneous connection between 6713 and 6602 (also 6601) via the RTSI bus, but you need to get a cable to connect between the boards. You can connect between the boards using the I/O pins of their respective signal conditioning hardware. These connections are slower. There are also PFI (Programmable Function Interfaces) connections that are set within the VI's.
    All that said, it is not obvious why you want to use the RTSI. You can use the PCI-6713 to generate AO. Presumably you have some signal conditioning accessory; which ever pin of that accessory the AO appears on, you wire it over to the SC accessory for the 6601 and the appropriate pin for the counter gate or
    source you want to use.
    Suggestions: Don't try to work in the context of your big VI for now. Get the AO bit and the counting bit to work together by themselves. Then shoe-horn them into the big VI. Also, consider a call to the NI help line. They are very good. 800.433.3488 (800IEEE488)
    In case you hadn't noticed the DAQ cards and Counter/Timer cards come in different flavors and there are specific example VI's to suit. 6602 uses NI-TIO chip, but PCI-671X are DAQ-STC. Again the NI help people are good at catching this kind of stuff.
    Your question is rather large and hard to manage. Perhaps if you break it down into small chunks the advise will be more free flowing.
    mike

  • My itunes 11 Home sharing is not working with my windows 7 PC and iPad it shows up on iPad and when I go to share the music app does loading for 3 mins and crashes I am using a virgin super hub router please please please help

    My itunes 11 Home sharing is not working with my windows 7 PC and iPad it shows up on iPad and when I go to share the music app does loading for 3 mins and crashes I am using a virgin super hub router please please please help

    My itunes 11 Home sharing is not working with my windows 7 PC and iPad it shows up on iPad and when I go to share the music app does loading for 3 mins and crashes I am using a virgin super hub router please please please help

  • New to FiOS, can I use my own modem and router

    I saw several questions similar to mine, but none that I saw answered my question for my scenario. I am sorry if this is a duplicate. I am new to FiOS. I have no other services from Verizon and do not plan to get any. No phone, no television, nothing. Just Internet. God willing, the installation will take place in two days. My house already has coaxial cabling. I have my own cable modem, a SURFboard SB6121, which goes to my router, a TP Link TL-WR941ND. None of my equipment advertises that it is FiOS compatible. I've seen other people asking about using their own modem and router, but in those cases the scenario involved other bundled services, and I understand a FiOS router is necessary to forward ports to television, phone, and computers. However, in my very simple scenario, can the Verizon optical network terminal simply feed its output to my coax, from there to my modem, then router, then comptuers? Is there any reason that wouldn't work? Verizon technical support just gave me a machine that wanted to help me troubleshoot my Internet connection, and I couldn't get from there to a human. Thanks in advance for the help!

    Banish the word and the device called "modem" from your home when using FiOS.  FiOS does not use modems.  Your cable modem is useless with FiOS.  Do not plug it in. FiOS uses routers.  The router connects to the ONT's WAN port using MoCA (coax) or Ethernet.  The installer will enable one of the ONT's WAN ports.  If you order 150Mbps or higher speeds, they will have to use Ethernet.  For slower speeds, coax is the default.  Many installers will use Ethernet if you ask nicely, but usually only if it isn't too much work.  Make sure it's easy to connect a router to the ONT using Ethernet, and you should be okay.  If Ethernet needs to be run through the walls, your best choice is get it done ahead of time.  You can always call later and get the ONT's WAN port switched. The only routers available with a MoCA WAN port are the Verizon models.  The Verizon routers are good devices for most users.  People who like to tweak their networking gear don't like them as many advanced features are limited or locked down.  You can't run any other router firmware on them.  WiFi range is decent, but not great.  I'm quite happy with my Quantum router.  YMMV. If you get Ethernet WAN enabled, you can use any router you want.  However, know that Verizon provides zero support for any other router.  They won't even mention it as an option.  That doesn't mean you can't use one, simply that you must do so without Verizon's help. There are reports that they won't even complete an install without one of their routers to verify service.  If you don't use one of their routers, consider renting one for a month to complete the install or even buying a used one.  If you own a Verizon router, you can install it if you ever suspect Verizon networking issues.  This will allow you to call their support. This FAQ is very helpful:http://www.dslreports.com/faq/16077 Good Luck. 

  • I want to set up my Epson printer using an airport and RR router. It was previously set up using a different router through HTC but same printer. How do I do this?

    I want to set up my Epson printer using an Airport and RR router. The same Mac Book and printer was formerly set up using a HTC router. How do I reset computer so it communicates with printer?

    http://support.apple.com/kb/HT3771
    Mac 101: Printing (Mac OS X v10.6)

  • I just bought a new iMac and I am using a apple air port router.  How do I connect mt windows PC to the air port router do I can move files

    I Just purchased a 21.5 iMac and connected it to the Internet using a apple air port router.  How do I connect my windows PC to my air port router so I can transfer files.

    It makes life easier to install the airport utility for windows.. which has a couple of different apps in it.. if you airport is new type then the utility is too old.. but is still valuable for Bonjour which provides network information for shared devices in the apple world to windows.. and a disk access agent..
    It will also help the Apple computer access shared directory in the windows computer.. nowadays this is pretty easy.

  • Using D-Link DI-624 Router for "G" Wireless Purposes

    I want to use an old D-link router in another part of the house to provide wireless "G" connectivity to my older devices, so I can use 5 GHz band for "N" connectivity exclusively via my Airport Extreme (Older version, not Gigabit).
    I go upstairs, plug the D-Links WAN port to the jack that connects to one of the Airport Extreme's LAN ports downstairs. I shut off dhcp server on the D-Link. I turn on the D-link's wireless capability (unencrypted for now, just for testing).
    When I plug a computer in to one of the LAN jacks of the D-Link, I have full connectivity to the internet. And I see the wireless signal from the D-Link which has a unique SSID. Unfortunately, while I can connect to the D-Link wirelessly, I cannot get to the internet.
    I'm sure I have something configured wrong.
    Questions:
    1. I have the Airport Extreme set to hand out ip addresses in the 10. range. Should I set up the D-Link router to get a static IP address from the Airport Extreme? How do I do that. Some sites suggest a 10 series IP address, but outside the range of the DHCP addresses that the Airport Extreme usually hands out.
    2. Any ideas on configuring the DI-624? I've shut off DHCP server (everyone says to do that). But Are there any other settings?
    3. Some tech help sites suggest not using the WAN Port at all on the D-link, but rather, connect to one of the LAN ports. Does this make any sense? Going from one of the LAN ports on the Airport Extreme to one of the D-Link's LAN ports.
    4. Once I get the wireless G network running, I'll fix the encryption.
    I think that in order to answer this question you'll need some first hand knowledge of the DI-624. Unfortunately, the DI-624 is now a discontinued product and there is little information available on D-link's web site.
    Thanks in advance for any advice.
    kenny

    If a Mac plugged into a LAN port on the D-Link gets internet access, the AirPort Extreme base station (AEBS) and D-Link are both configured properly.
    The wireless side of the D-Link should also be acting properly since LAN access is working.
    The most likely problem is that your Mac has incorrect DNS information in the System Preferences->Network preference pane->AirPort area.

  • I have a hard drive for CD storage that needs to connect to the Ethernet router. sInce my router is not in this room, and in another room, I want to use my Mac as a router for the drive, and share the wifi. Ho do I do this

    I have a hard drive for CD storage that needs to connect to the Ethernet router. sInce my router is not in this room, and in another room, I want to use my Mac as a router for the drive, and share the wifi. Ho do I do this? I gace tried the System Preferences -> Sharing, shared internet to Ethernet, but can't se ethe device on Finder

    Djembe wrote:
    UEFI (unified extensible firmware interface) boot requires Global unique identifier Partition Table (GPT) as opposed to the older Master Boot Record (MBR). If your existing drive is formatted in MBR, you will need to adjust BIOS settings to enable legacy boot in order for it to work properly.
    Is there a performance difference between GPT and MBR? If GPT is better, I do not mind formatting the drive with it.
    5. No special drivers are needed.
    Thanks. What about the thunderbolt port?
    7. I think Lenovo estimates 6 hours.
    Lenovo says 6 hours with the 6-cell battery on its website.
    BrendaEM wrote:
    Hi,
    There was a serious BIOS/UEFI problem with that SSD . Perhaps this thread will save you some headaches. Someone is recomending shutting off Rapid Boot in the setup, which would probable mean little with a SSD, anyway.
    I read through this, and it looks like the problem was fixed in a BIOS update, which I plan to do. However, it also seems like Intel Rapid Start is not even worth it in the first place, as sleep consumes almost no power at all.
    W540: i7-4700mq, K2100m, 8 GB DDR3L, 512 GB SSD
    T510: i7-620m, NVS 3100m, 8 GB DDR3, 512 GB SSD

  • Using macbook as a wireless router for non-apple devices

    im trying to use my mac as wireless router for my xbox. i went into share under system preferences, and made a network with a WEP password. I can see the network on my xbox but it requires an IP adress...
    i guess what im really asking is, if the mac can automatically assign IP adresses to devices on the network

    I use my MBP regularly to share internet connection with PCs. Usually the PCs do a 'search' for a network and then 'connect' to the network name set in the Airport options... drop down panel. They get the IP automatically.
    In the system preferences>share> there is a button on the right bottom which says 'airport options..' and in the drop down panel, you set the name or SSID and the WEP key.
    Maybe you should check XBOX settings if the network settings are manual or automatic?
    Hope that helps.

  • Can i use a belkin wireless g router with an iMac

    can i use a belkin wireless g router with an imac

    It will work. The wireless card in iMacs (recent ones) work with n, g, and b networks. The g protocol is slower (54 mbs) versus n (130 mbs up to 300 mbs). My employer has hundreds of such access points and has been updating them all to n, but there are still some g routers they haven't gotten to, and they work fine. 54 mbs is not bad, it's about 5 megabytes/sec roughly. Typical actual throughput is lower than these numbers by ~ 50%, so doing a large Mac OS update download of 300 Megabytes would take about ~ 2 minutes with a g router, and maybe a bit less than 1 minute with an n router.

  • TS1398 my ipod touch won't connect to my wi-fi which is locked,i've tried using the password on the router but it does not accept it,ive phoned talk talk,,,,let's not go there!!!!1

    my ipod touch will not connect to my home wi-fi internet which is locked,i've tried using the password on the router but it does not accept it.
    i phoned talk talk for advice but unfortunately i would have been as well asking an axe weilding monkey high on cocaine...
    appreciate any advice...
    thanks.
    martin.

    thanks for getting back so quickly.when i put  password into ipod it comes up with message
    "unable to join network"
    the router is using AES incription.
    my wi-fi is a secured connection WPA2,
    i believe i should have WEP or WAP connection for it to work?
    i have set up my daughters nintendo 3ds lite to internet no problem using existing connection.
    talktalk said they do not support apple ipod touch sytem?
    very confusing,particulary as i've bought 3 ipod touch ,,,,mmmmmmm!
    thanks again..

  • Can CRM 2015 Online use the CRM 2013 Email Router?

    We are trying to plan our upgrade to CRM 2015 Online from CRM 2013 Online. We currently use the CRM 2013 Email Router and want to know if we need to upgrade the email router immediately after the CRM server is upgraded or if we could wait a short period
    of time. I searched but could not find any information on the Email Router compatibility. Does anyone have any information?

    Why are you using the email router if your Exchange Server is also Online?  Dynamics CRM Online has Server Sync built in so it will directly communicate to Exchange Online.  Much better solution than rolling up an email Router. 
    Also, if you don't have access to the Exchange server, I' doubt there's much you can do, since you don't have all the tools you need to troubleshoot the issue.
    The postings on this site are solely my own and do not represent or constitute Hitachi Solutions' positions, views, strategies or opinions.

  • I have a problem with using MacBook Pro as wifi router when connected to ethernet

    I have a problem with using MacBook Pro as wifi router when connected to ethernet. The Airport icon changes to show a laptop inside, my iPad shows connected (I think) but Safari will not operate. I tried pinging my iPad, it seems to see the iPad, but no connection to Safari or to other apps such as Good on the iPad. I have read many posting and tried repeatedly via Sharing in Systems Preferences, but no luck. Suggestions to fix, or is this a Lion problem?

    Usually this is a problem related to the domain name server address. If you open Network preferences, select your Ethernet port then click on the Advanced button then on the DNS tab. You will likely see an entry like 10.0.1.1 already listed. Click on the Add [-] button and enter 208.67.222.222 then click on the OK button and then on the Apply button.  See if this helps.
    if it does not help then repeat the above but with the Airport port.

  • Can i use time capsule as the router with sky broadband

    how do i use time capsule as the router. I contacted my internet provider  which is Sky who had no info other than to suggest trying a sky forum.

    It depends on the type of modem they gave you.. and if you can bridge it.
    I suspect you cannot use the TC in router mode with sky.. but tell us more.. if it is adsl and they accept pppoe then you can get it to work.. otherwise no.. just use the TC in bridge.

  • TS1398 have been connected to my wireless network using a netgear sky broadband router succesfully for a few weeks, suddenly can't connect, network is showing but no signal - all other wireless gadgets are connected just fine - including iphone - any idea

    my ipad 4 has been connected to my wireless network using a netgear sky broadband router succesfully for a few weeks, suddenly can't connect, network is showing but no signal - all other wireless gadgets are connected just fine - including iphone - any ideas?

    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are droping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    iOS 6 Wifi Problems/Fixes
    How To: Workaround iPad Wi-Fi Issues
    http://www.theipadfan.com/workaround-ipad-wifi-issues/
    Another Fix For iOS 6 WiFi Problems
    http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
    Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Connect iPad to Wi-Fi (with troubleshooting info)
    http://thehowto.wikidot.com/wifi-connect-ipad
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • HT201342 we only have one apple id for our household.  i would like to use icloud to manage all our email accounts within our household. i currently use gmail.  is there a way to continue to use gmail and have messages routed through icloud so no change i

    i am new to icloud.  i would like to manage all our household email accounts through icloud.  i currently use gmail.  is there a way to route all gmail messages through an icloud email so i do not have to change my email address?  also how do i create multiple email accounts using the same apple id?
    thanks all.
    Mike

    No, iCloud does not handle 3rd party mail, and Google can already sync to all your devices without any help.
    iCloud accounts are individual, there is no 'Family' account. Open an account for each user, each will have an iCloud address.

Maybe you are looking for