Using onboard audio with SB Live card installed

Is it possible (or even wise) to use onboard audio with a SB Live Value card installed. I need to keep the SB Live card as I still have a couple of gameport devices, but I'd like to take advantage of the onboard audio (or should that be free myself from the disdavantages of the SB Live).
I guess the key issue is diabling the SB Live sound but still keeping the gameport active. Is this do-able or am I just opening a can of worms ?

Could well be a can of worms.
I can only say that I have had both installed on my K7n420 NF1 and was able to switch back and forth, all I did was set what sound controller I wanted to be used in the sound device config in the windows sound control panel.
Try it and see....but I am a bit pessimistic as far as it doing what you expect.

Similar Messages

  • Unable to Use Onboard Audio with Nvidia GPU since Linux 3.4

    I am currently stuck using linux 3.3.8-1 along with nvidia 295.49-1, because I don't know how to workaround the kernel disabling MSI for snd-hda-intel. This module is used by both the Nvidia HDMI audio and the ALC880 onboard audio. Previously, I have been able to disable HDMI audio to be able to use the onboard audio, but now I don't know what to do. I have attempted to use "options snd-hda-intel enable_msi=1" when modprobing on boot, which gets rid of the "hda_intel: Disabling MSI" message but it hasn't given me a working onboard audio output.
    I have also used the following command along with enable_msi=1 (found here: http://www.mjmwired.net/kernel/Document … HOWTO.txt) in my rc.local
    echo 1 > /sys/bus/pci/devices/0000\:00\:1b.0/msi_bus
    Of course, it is my assumption that the kernel disabling MSI is the cause of the problem, but it might be something else. Please let me know if any additional logs would be helpful.
    Linux 3.4.4-3, Nvidia 302.17-2  Dmesg Output
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Linux version 3.4.4-3-ARCH (nobody@rampage) (gcc version 4.7.1 (GCC) ) #1 SMP PREEMPT Tue Jul 3 15:35:13 UTC 2012
    [ 0.000000] BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
    [ 0.000000] BIOS-e820: 0000000000100000 - 000000003fe54000 (usable)
    [ 0.000000] BIOS-e820: 000000003fe54000 - 000000003fee8000 (ACPI NVS)
    [ 0.000000] BIOS-e820: 000000003fee8000 - 000000003ff00000 (ACPI data)
    [ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
    [ 0.000000] DMI 2.3 present.
    [ 0.000000] DMI: 507GR /D915GAG, BIOS AG91510J.15A.0816.2005.0214.1818 02/14/2005
    [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
    [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
    [ 0.000000] last_pfn = 0x3fe54 max_arch_pfn = 0x100000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-FFFFF uncachable
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 000000000 mask FC0000000 write-back
    [ 0.000000] 1 base 03FF00000 mask FFFF00000 uncachable
    [ 0.000000] 2 disabled
    [ 0.000000] 3 disabled
    [ 0.000000] 4 disabled
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] found SMP MP-table at [c00fe650] fe650
    [ 0.000000] initial memory mapped : 0 - 00c00000
    [ 0.000000] Base memory trampoline at [c009a000] 9a000 size 16384
    [ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
    [ 0.000000] 0000000000 - 0000400000 page 4k
    [ 0.000000] 0000400000 - 0037400000 page 2M
    [ 0.000000] 0037400000 - 00377fe000 page 4k
    [ 0.000000] kernel direct mapping tables up to 377fe000 @ bfb000-c00000
    [ 0.000000] RAMDISK: 3fb6f000 - 3fe44000
    [ 0.000000] Allocated new RAMDISK: 37529000 - 377fd6a7
    [ 0.000000] Move RAMDISK from 000000003fb6f000 - 000000003fe436a6 to 37529000 - 377fd6a6
    [ 0.000000] ACPI: RSDP 000fe020 00014 (v00 GATEWA)
    [ 0.000000] ACPI: RSDT 3fefde48 00038 (v01 GATEWA 04DT037 00000330 MSFT 01000013)
    [ 0.000000] ACPI: FACP 3fefcf10 00074 (v01 GATEWA 04DT037 00000330 MSFT 01000013)
    [ 0.000000] ACPI: DSDT 3fef8010 0339C (v01 GATEWA 04DT037 00000330 MSFT 01000013)
    [ 0.000000] ACPI: FACS 3fee5c40 00040
    [ 0.000000] ACPI: APIC 3fefce10 00068 (v01 GATEWA 04DT037 00000330 MSFT 01000013)
    [ 0.000000] ACPI: WDDT 3fef7f90 00040 (v01 GATEWA 04DT037 00000330 MSFT 01000013)
    [ 0.000000] ACPI: MCFG 3fef7f10 0003C (v01 GATEWA 04DT037 00000330 MSFT 01000013)
    [ 0.000000] ACPI: SSDT 3fef6d90 00124 (v01 GATEWA CpuPm 00000330 MSFT 01000013)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] 134MB HIGHMEM available.
    [ 0.000000] 887MB LOWMEM available.
    [ 0.000000] mapped low ram: 0 - 377fe000
    [ 0.000000] low ram: 0 - 377fe000
    [ 0.000000] Zone PFN ranges:
    [ 0.000000] DMA 0x00000010 -> 0x00001000
    [ 0.000000] Normal 0x00001000 -> 0x000377fe
    [ 0.000000] HighMem 0x000377fe -> 0x0003fe54
    [ 0.000000] Movable zone start PFN for each node
    [ 0.000000] Early memory PFN ranges
    [ 0.000000] 0: 0x00000010 -> 0x0000009f
    [ 0.000000] 0: 0x00000100 -> 0x0003fe54
    [ 0.000000] On node 0 totalpages: 261603
    [ 0.000000] free_area_init_node: node 0, pgdat c061ec40, node_mem_map f6d28200
    [ 0.000000] DMA zone: 32 pages used for memmap
    [ 0.000000] DMA zone: 0 pages reserved
    [ 0.000000] DMA zone: 3951 pages, LIFO batch:0
    [ 0.000000] Normal zone: 1744 pages used for memmap
    [ 0.000000] Normal zone: 221486 pages, LIFO batch:31
    [ 0.000000] HighMem zone: 269 pages used for memmap
    [ 0.000000] HighMem zone: 34121 pages, LIFO batch:7
    [ 0.000000] Using APIC driver default
    [ 0.000000] ACPI: PM-Timer IO Port: 0x408
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
    [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
    [ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
    [ 0.000000] Allocating PCI resources starting at 3ff00000 (gap: 3ff00000:c0100000)
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 13 pages/cpu @f6d07000 s31424 r0 d21824 u53248
    [ 0.000000] pcpu-alloc: s31424 r0 d21824 u53248 alloc=13*4096
    [ 0.000000] pcpu-alloc: [0] 0 [0] 1
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259558
    [ 0.000000] Kernel command line: root=/dev/disk/by-uuid/10f8033d-8fe9-46be-bccf-68a14025bbaa ro init=/bin/systemd
    [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
    [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    [ 0.000000] Initializing CPU#0
    [ 0.000000] allocated 2093600 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] Initializing HighMem for node 0 (000377fe:0003fe54)
    [ 0.000000] Memory: 1025576k/1046864k available (3810k kernel code, 20836k reserved, 1471k data, 524k init, 137560k highmem)
    [ 0.000000] virtual kernel memory layout:
    [ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
    [ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    [ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
    [ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
    [ 0.000000] .init : 0xc0629000 - 0xc06ac000 ( 524 kB)
    [ 0.000000] .data : 0xc04b88f7 - 0xc0628800 (1471 kB)
    [ 0.000000] .text : 0xc0100000 - 0xc04b88f7 (3810 kB)
    [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
    [ 0.000000] SLUB: Genslabs=15, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] NR_IRQS:2304 nr_irqs:512 16
    [ 0.000000] CPU 0 irqstacks, hard=f6408000 soft=f640a000
    [ 0.000000] Console: colour VGA+ 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] Fast TSC calibration using PIT
    [ 0.000000] Detected 2999.992 MHz processor.
    [ 0.006668] Calibrating delay loop (skipped), value calculated using timer frequency.. 6002.98 BogoMIPS (lpj=9999973)
    [ 0.006674] pid_max: default: 32768 minimum: 301
    [ 0.006706] Security Framework initialized
    [ 0.006712] AppArmor: AppArmor disabled by boot time parameter
    [ 0.006735] Mount-cache hash table entries: 512
    [ 0.007027] Initializing cgroup subsys cpuacct
    [ 0.007032] Initializing cgroup subsys memory
    [ 0.007043] Initializing cgroup subsys devices
    [ 0.007046] Initializing cgroup subsys freezer
    [ 0.007049] Initializing cgroup subsys net_cls
    [ 0.007052] Initializing cgroup subsys blkio
    [ 0.007102] CPU: Physical Processor ID: 0
    [ 0.007105] CPU: Processor Core ID: 0
    [ 0.007108] mce: CPU supports 4 MCE banks
    [ 0.007122] CPU0: Thermal monitoring enabled (TM1)
    [ 0.007127] using mwait in idle threads.
    [ 0.010796] ACPI: Core revision 20120320
    [ 0.013347] ftrace: allocating 16930 entries in 34 pages
    [ 0.023410] Enabling APIC mode: Flat. Using 1 I/O APICs
    [ 0.023795] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.058322] CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 01
    [ 0.059996] Performance Events: Netburst events, Netburst P4/Xeon PMU driver.
    [ 0.059996] ... version: 0
    [ 0.059996] ... bit width: 40
    [ 0.059996] ... generic registers: 18
    [ 0.059996] ... value mask: 000000ffffffffff
    [ 0.059996] ... max period: 0000007fffffffff
    [ 0.059996] ... fixed-purpose events: 0
    [ 0.059996] ... event mask: 000000000003ffff
    [ 0.076747] NMI watchdog: enabled, takes one hw-pmu counter.
    [ 0.096685] CPU 1 irqstacks, hard=f64ae000 soft=f64b0000
    [ 0.096689] Booting Node 0, Processors #1 Ok.
    [ 0.009999] Initializing CPU#1
    [ 0.109847] NMI watchdog: enabled, takes one hw-pmu counter.
    [ 0.109913] Brought up 2 CPUs
    [ 0.109918] Total of 2 processors activated (12004.96 BogoMIPS).
    [ 0.110087] devtmpfs: initialized
    [ 0.110253] PM: Registering ACPI NVS region [mem 0x3fe54000-0x3fee7fff] (606208 bytes)
    [ 0.111622] NET: Registered protocol family 16
    [ 0.111622] ACPI: bus type pci registered
    [ 0.111622] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.111622] PCI: not using MMCONFIG
    [ 0.112603] PCI: Using configuration type 1 for base access
    [ 0.116699] bio: create slab <bio-0> at 0
    [ 0.116741] ACPI: Added _OSI(Module Device)
    [ 0.116741] ACPI: Added _OSI(Processor Device)
    [ 0.116741] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.116741] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.117482] ACPI: EC: Look up EC in DSDT
    [ 0.119433] ACPI: Interpreter enabled
    [ 0.119446] ACPI: (supports S0 S1 S3 S4 S5)
    [ 0.119477] ACPI: Using IOAPIC for interrupt routing
    [ 0.119501] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.119654] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
    [ 0.119657] PCI: Using MMCONFIG for extended config space
    [ 0.121061] ACPI: No dock devices found.
    [ 0.121073] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
    [ 0.122518] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.125297] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
    [ 0.125302] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
    [ 0.125306] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
    [ 0.125310] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000fffff] (ignored)
    [ 0.125314] pci_root PNP0A03:00: host bridge window [mem 0xf0000000-0xfbffffff] (ignored)
    [ 0.125317] pci_root PNP0A03:00: host bridge window [mem 0x40000000-0xe0000000] (ignored)
    [ 0.125321] PCI: root bus 00: using default resources
    [ 0.125377] PCI host bridge to bus 0000:00
    [ 0.125382] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
    [ 0.125385] pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
    [ 0.125400] pci 0000:00:00.0: [8086:2580] type 00 class 0x060000
    [ 0.125463] pci 0000:00:01.0: [8086:2581] type 01 class 0x060400
    [ 0.125521] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
    [ 0.125577] pci 0000:00:1b.0: [8086:2668] type 00 class 0x040300
    [ 0.125597] pci 0000:00:1b.0: reg 10: [mem 0x53300000-0x53303fff 64bit]
    [ 0.125676] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 0.125704] pci 0000:00:1c.0: [8086:2660] type 01 class 0x060400
    [ 0.125786] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 0.125815] pci 0000:00:1c.1: [8086:2662] type 01 class 0x060400
    [ 0.125898] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
    [ 0.125928] pci 0000:00:1c.2: [8086:2664] type 01 class 0x060400
    [ 0.126011] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
    [ 0.126040] pci 0000:00:1c.3: [8086:2666] type 01 class 0x060400
    [ 0.126123] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
    [ 0.126154] pci 0000:00:1d.0: [8086:2658] type 00 class 0x0c0300
    [ 0.126201] pci 0000:00:1d.0: reg 20: [io 0x4080-0x409f]
    [ 0.126239] pci 0000:00:1d.1: [8086:2659] type 00 class 0x0c0300
    [ 0.126285] pci 0000:00:1d.1: reg 20: [io 0x4060-0x407f]
    [ 0.126322] pci 0000:00:1d.2: [8086:265a] type 00 class 0x0c0300
    [ 0.126368] pci 0000:00:1d.2: reg 20: [io 0x4040-0x405f]
    [ 0.126405] pci 0000:00:1d.3: [8086:265b] type 00 class 0x0c0300
    [ 0.126451] pci 0000:00:1d.3: reg 20: [io 0x4020-0x403f]
    [ 0.126498] pci 0000:00:1d.7: [8086:265c] type 00 class 0x0c0320
    [ 0.126521] pci 0000:00:1d.7: reg 10: [mem 0x53304000-0x533043ff]
    [ 0.126613] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    [ 0.126638] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
    [ 0.126718] pci 0000:00:1f.0: [8086:2640] type 00 class 0x060100
    [ 0.126810] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
    [ 0.126823] pci 0000:00:1f.0: LPC Generic IO decode 1 PIO at 0680-06ff
    [ 0.126850] pci 0000:00:1f.1: [8086:266f] type 00 class 0x01018a
    [ 0.126867] pci 0000:00:1f.1: reg 10: [io 0x40d8-0x40df]
    [ 0.126878] pci 0000:00:1f.1: reg 14: [io 0x40ec-0x40ef]
    [ 0.126889] pci 0000:00:1f.1: reg 18: [io 0x40d0-0x40d7]
    [ 0.126901] pci 0000:00:1f.1: reg 1c: [io 0x40e8-0x40eb]
    [ 0.126912] pci 0000:00:1f.1: reg 20: [io 0x40b0-0x40bf]
    [ 0.126954] pci 0000:00:1f.2: [8086:2651] type 00 class 0x01018f
    [ 0.126971] pci 0000:00:1f.2: reg 10: [io 0x40c8-0x40cf]
    [ 0.126981] pci 0000:00:1f.2: reg 14: [io 0x40e4-0x40e7]
    [ 0.126991] pci 0000:00:1f.2: reg 18: [io 0x40c0-0x40c7]
    [ 0.127002] pci 0000:00:1f.2: reg 1c: [io 0x40e0-0x40e3]
    [ 0.127012] pci 0000:00:1f.2: reg 20: [io 0x40a0-0x40af]
    [ 0.127053] pci 0000:00:1f.2: PME# supported from D3hot
    [ 0.127072] pci 0000:00:1f.3: [8086:266a] type 00 class 0x0c0500
    [ 0.127129] pci 0000:00:1f.3: reg 20: [io 0x4000-0x401f]
    [ 0.127217] pci 0000:01:00.0: [10de:0a65] type 00 class 0x030000
    [ 0.127232] pci 0000:01:00.0: reg 10: [mem 0x52000000-0x52ffffff]
    [ 0.127247] pci 0000:01:00.0: reg 14: [mem 0x40000000-0x4fffffff 64bit pref]
    [ 0.127261] pci 0000:01:00.0: reg 1c: [mem 0x50000000-0x51ffffff 64bit pref]
    [ 0.127271] pci 0000:01:00.0: reg 24: [io 0x3000-0x307f]
    [ 0.127281] pci 0000:01:00.0: reg 30: [mem 0xfff80000-0xffffffff pref]
    [ 0.127352] pci 0000:01:00.1: [10de:0be3] type 00 class 0x040300
    [ 0.127367] pci 0000:01:00.1: reg 10: [mem 0x53000000-0x53003fff]
    [ 0.136679] pci 0000:00:01.0: PCI bridge to [bus 01-01]
    [ 0.136685] pci 0000:00:01.0: bridge window [io 0x3000-0x3fff]
    [ 0.136689] pci 0000:00:01.0: bridge window [mem 0x52000000-0x530fffff]
    [ 0.136695] pci 0000:00:01.0: bridge window [mem 0x40000000-0x51ffffff pref]
    [ 0.136765] pci 0000:02:00.0: [1b21:0612] type 00 class 0x010601
    [ 0.136788] pci 0000:02:00.0: reg 10: [io 0x2028-0x202f]
    [ 0.136804] pci 0000:02:00.0: reg 14: [io 0x2034-0x2037]
    [ 0.136819] pci 0000:02:00.0: reg 18: [io 0x2020-0x2027]
    [ 0.136836] pci 0000:02:00.0: reg 1c: [io 0x2030-0x2033]
    [ 0.136852] pci 0000:02:00.0: reg 20: [io 0x2000-0x201f]
    [ 0.136868] pci 0000:02:00.0: reg 24: [mem 0x53200000-0x532001ff]
    [ 0.136885] pci 0000:02:00.0: reg 30: [mem 0xffff0000-0xffffffff pref]
    [ 0.146676] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
    [ 0.146682] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
    [ 0.146687] pci 0000:00:1c.0: bridge window [mem 0x53200000-0x532fffff]
    [ 0.146740] pci 0000:00:1c.1: PCI bridge to [bus 03-03]
    [ 0.146747] pci 0000:00:1c.1: bridge window [mem 0x53400000-0x534fffff]
    [ 0.146798] pci 0000:00:1c.2: PCI bridge to [bus 04-04]
    [ 0.146805] pci 0000:00:1c.2: bridge window [mem 0x53500000-0x535fffff]
    [ 0.146858] pci 0000:00:1c.3: PCI bridge to [bus 05-05]
    [ 0.146866] pci 0000:00:1c.3: bridge window [mem 0x53600000-0x536fffff]
    [ 0.146917] pci 0000:06:05.0: [11c1:5811] type 00 class 0x0c0010
    [ 0.146938] pci 0000:06:05.0: reg 10: [mem 0x53101000-0x53101fff]
    [ 0.147024] pci 0000:06:05.0: supports D1 D2
    [ 0.147027] pci 0000:06:05.0: PME# supported from D0 D1 D2 D3hot
    [ 0.147053] pci 0000:06:08.0: [8086:1064] type 00 class 0x020000
    [ 0.147074] pci 0000:06:08.0: reg 10: [mem 0x53100000-0x53100fff]
    [ 0.147086] pci 0000:06:08.0: reg 14: [io 0x1000-0x103f]
    [ 0.147161] pci 0000:06:08.0: supports D1 D2
    [ 0.147164] pci 0000:06:08.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.147208] pci 0000:00:1e.0: PCI bridge to [bus 06-06] (subtractive decode)
    [ 0.147214] pci 0000:00:1e.0: bridge window [io 0x1000-0x1fff]
    [ 0.147219] pci 0000:00:1e.0: bridge window [mem 0x53100000-0x531fffff]
    [ 0.147227] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode)
    [ 0.147231] pci 0000:00:1e.0: bridge window [mem 0x00000000-0xffffffff] (subtractive decode)
    [ 0.147260] pci_bus 0000:00: on NUMA node 0
    [ 0.147266] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    [ 0.147465] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
    [ 0.147735] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
    [ 0.147802] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
    [ 0.147870] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
    [ 0.147936] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
    [ 0.148039] pci0000:00: Requesting ACPI _OSC control (0x1d)
    [ 0.148044] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
    [ 0.148047] ACPI _OSC control for PCIe not granted, disabling ASPM
    [ 0.152485] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
    [ 0.152581] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11 12)
    [ 0.152676] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
    [ 0.152768] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
    [ 0.152859] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12)
    [ 0.152951] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
    [ 0.153045] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
    [ 0.153138] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 *10 11 12)
    [ 0.153367] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.153374] vgaarb: loaded
    [ 0.153377] vgaarb: bridge control possible 0000:01:00.0
    [ 0.153377] PCI: Using ACPI for IRQ routing
    [ 0.160505] PCI: pci_cache_line_size set to 64 bytes
    [ 0.160612] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
    [ 0.160616] reserve RAM buffer: 000000003fe54000 - 000000003fffffff
    [ 0.160771] NetLabel: Initializing
    [ 0.160775] NetLabel: domain hash size = 128
    [ 0.160777] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.160799] NetLabel: unlabeled traffic allowed by default
    [ 0.160906] hpet clockevent registered
    [ 0.160911] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
    [ 0.160917] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    [ 0.160924] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
    [ 0.173350] Switching to clocksource hpet
    [ 0.182676] pnp: PnP ACPI init
    [ 0.182706] ACPI: bus type pnp registered
    [ 0.184200] pnp 00:00: [bus 00-ff]
    [ 0.184205] pnp 00:00: [io 0x0cf8-0x0cff]
    [ 0.184209] pnp 00:00: [io 0x0000-0x0cf7 window]
    [ 0.184212] pnp 00:00: [io 0x0d00-0xffff window]
    [ 0.184216] pnp 00:00: [mem 0x000a0000-0x000bffff window]
    [ 0.184219] pnp 00:00: [mem 0x000c0000-0x000fffff window]
    [ 0.184223] pnp 00:00: [mem 0xf0000000-0xfbffffff window]
    [ 0.184229] pnp 00:00: [mem 0x40000000-0xe0000000 window]
    [ 0.184297] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
    [ 0.184317] pnp 00:01: [mem 0xe0000000-0xefffffff]
    [ 0.184321] pnp 00:01: [mem 0xfed13000-0xfed13fff]
    [ 0.184324] pnp 00:01: [mem 0xfed14000-0xfed17fff]
    [ 0.184327] pnp 00:01: [mem 0xfed18000-0xfed18fff]
    [ 0.184330] pnp 00:01: [mem 0xfed19000-0xfed19fff]
    [ 0.184333] pnp 00:01: [mem 0xfed1c000-0xfed1ffff]
    [ 0.184336] pnp 00:01: [mem 0xfed20000-0xfed9ffff]
    [ 0.184412] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved
    [ 0.184417] system 00:01: [mem 0xfed13000-0xfed13fff] has been reserved
    [ 0.184421] system 00:01: [mem 0xfed14000-0xfed17fff] has been reserved
    [ 0.184425] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
    [ 0.184429] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
    [ 0.184432] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
    [ 0.184436] system 00:01: [mem 0xfed20000-0xfed9ffff] has been reserved
    [ 0.184442] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.184642] pnp 00:02: [io 0x0000-0x000f]
    [ 0.184646] pnp 00:02: [io 0x0081-0x0083]
    [ 0.184649] pnp 00:02: [io 0x0087]
    [ 0.184652] pnp 00:02: [io 0x0089-0x008b]
    [ 0.184655] pnp 00:02: [io 0x008f]
    [ 0.184658] pnp 00:02: [io 0x00c0-0x00df]
    [ 0.184661] pnp 00:02: [dma 4]
    [ 0.184706] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
    [ 0.184723] pnp 00:03: [io 0x0070-0x0071]
    [ 0.184726] pnp 00:03: [io 0x0074-0x0077]
    [ 0.184740] pnp 00:03: [irq 8]
    [ 0.184783] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.184802] pnp 00:04: [io 0x00f0]
    [ 0.184810] pnp 00:04: [irq 13]
    [ 0.184854] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
    [ 0.184871] pnp 00:05: [io 0x0061]
    [ 0.184919] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
    [ 0.184938] pnp 00:06: [io 0x0500-0x053f]
    [ 0.184942] pnp 00:06: [io 0x0400-0x047f]
    [ 0.184945] pnp 00:06: [io 0x0092]
    [ 0.184948] pnp 00:06: [io 0x0680-0x06ff]
    [ 0.184951] pnp 00:06: [io 0x0010-0x001f]
    [ 0.184954] pnp 00:06: [io 0x0072-0x0073]
    [ 0.184956] pnp 00:06: [io 0x0080]
    [ 0.184959] pnp 00:06: [io 0x0084-0x0086]
    [ 0.184962] pnp 00:06: [io 0x0088]
    [ 0.184965] pnp 00:06: [io 0x008c-0x008e]
    [ 0.184968] pnp 00:06: [io 0x0090-0x009f]
    [ 0.185047] system 00:06: [io 0x0500-0x053f] has been reserved
    [ 0.185051] system 00:06: [io 0x0400-0x047f] has been reserved
    [ 0.185055] system 00:06: [io 0x0680-0x06ff] has been reserved
    [ 0.185061] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.185320] pnp 00:07: [io 0x0378-0x037f]
    [ 0.185329] pnp 00:07: [irq 7]
    [ 0.185426] pnp 00:07: Plug and Play ACPI device, IDs PNP0400 (active)
    [ 0.185514] pnp 00:08: [irq 12]
    [ 0.185563] pnp 00:08: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active)
    [ 0.185600] pnp 00:09: [io 0x0060]
    [ 0.185604] pnp 00:09: [io 0x0064]
    [ 0.185611] pnp 00:09: [irq 1]
    [ 0.185661] pnp 00:09: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
    [ 0.185822] pnp 00:0a: [io 0x03f8-0x03ff]
    [ 0.185831] pnp 00:0a: [irq 4]
    [ 0.185938] pnp 00:0a: Plug and Play ACPI device, IDs PNP0501 (active)
    [ 0.185964] pnp 00:0b: [mem 0xfec00000-0xfec000ff]
    [ 0.186015] pnp 00:0b: Plug and Play ACPI device, IDs PNP0003 (active)
    [ 0.186047] pnp: PnP ACPI: found 12 devices
    [ 0.186049] ACPI: ACPI bus type pnp unregistered
    [ 0.224576] pci 0000:01:00.0: no compatible bridge window for [mem 0xfff80000-0xffffffff pref]
    [ 0.224583] pci 0000:02:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref]
    [ 0.224623] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x001fffff pref] to [bus 02-02] add_size 200000
    [ 0.224635] pci 0000:00:1c.1: bridge window [io 0x1000-0x0fff] to [bus 03-03] add_size 1000
    [ 0.224640] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03-03] add_size 200000
    [ 0.224651] pci 0000:00:1c.2: bridge window [io 0x1000-0x0fff] to [bus 04-04] add_size 1000
    [ 0.224656] pci 0000:00:1c.2: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 04-04] add_size 200000
    [ 0.224667] pci 0000:00:1c.3: bridge window [io 0x1000-0x0fff] to [bus 05-05] add_size 1000
    [ 0.224672] pci 0000:00:1c.3: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 05-05] add_size 200000
    [ 0.224692] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x001fffff pref] get_res_add_size add_size 200000
    [ 0.224696] pci 0000:00:1c.1: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
    [ 0.224701] pci 0000:00:1c.2: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
    [ 0.224705] pci 0000:00:1c.3: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
    [ 0.224709] pci 0000:00:1c.1: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
    [ 0.224713] pci 0000:00:1c.2: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
    [ 0.224717] pci 0000:00:1c.3: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
    [ 0.224726] pci 0000:00:1c.0: BAR 15: assigned [mem 0x53700000-0x539fffff pref]
    [ 0.224731] pci 0000:00:1c.1: BAR 15: assigned [mem 0x53a00000-0x53bfffff 64bit pref]
    [ 0.224736] pci 0000:00:1c.2: BAR 15: assigned [mem 0x53c00000-0x53dfffff 64bit pref]
    [ 0.224740] pci 0000:00:1c.3: BAR 15: assigned [mem 0x53e00000-0x53ffffff 64bit pref]
    [ 0.224745] pci 0000:00:1c.1: BAR 13: assigned [io 0x5000-0x5fff]
    [ 0.224750] pci 0000:00:1c.2: BAR 13: assigned [io 0x6000-0x6fff]
    [ 0.224754] pci 0000:00:1c.3: BAR 13: assigned [io 0x7000-0x7fff]
    [ 0.224761] pci 0000:01:00.0: BAR 6: assigned [mem 0x53080000-0x530fffff pref]
    [ 0.224765] pci 0000:00:01.0: PCI bridge to [bus 01-01]
    [ 0.224770] pci 0000:00:01.0: bridge window [io 0x3000-0x3fff]
    [ 0.224775] pci 0000:00:01.0: bridge window [mem 0x52000000-0x530fffff]
    [ 0.224780] pci 0000:00:01.0: bridge window [mem 0x40000000-0x51ffffff pref]
    [ 0.224788] pci 0000:02:00.0: BAR 6: assigned [mem 0x53700000-0x5370ffff pref]
    [ 0.224791] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
    [ 0.224796] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
    [ 0.224802] pci 0000:00:1c.0: bridge window [mem 0x53200000-0x532fffff]
    [ 0.224807] pci 0000:00:1c.0: bridge window [mem 0x53700000-0x539fffff pref]
    [ 0.224815] pci 0000:00:1c.1: PCI bridge to [bus 03-03]
    [ 0.224819] pci 0000:00:1c.1: bridge window [io 0x5000-0x5fff]
    [ 0.224825] pci 0000:00:1c.1: bridge window [mem 0x53400000-0x534fffff]
    [ 0.224831] pci 0000:00:1c.1: bridge window [mem 0x53a00000-0x53bfffff 64bit pref]
    [ 0.224838] pci 0000:00:1c.2: PCI bridge to [bus 04-04]
    [ 0.224842] pci 0000:00:1c.2: bridge window [io 0x6000-0x6fff]
    [ 0.224849] pci 0000:00:1c.2: bridge window [mem 0x53500000-0x535fffff]
    [ 0.224854] pci 0000:00:1c.2: bridge window [mem 0x53c00000-0x53dfffff 64bit pref]
    [ 0.224861] pci 0000:00:1c.3: PCI bridge to [bus 05-05]
    [ 0.224865] pci 0000:00:1c.3: bridge window [io 0x7000-0x7fff]
    [ 0.224872] pci 0000:00:1c.3: bridge window [mem 0x53600000-0x536fffff]
    [ 0.224877] pci 0000:00:1c.3: bridge window [mem 0x53e00000-0x53ffffff 64bit pref]
    [ 0.224885] pci 0000:00:1e.0: PCI bridge to [bus 06-06]
    [ 0.224889] pci 0000:00:1e.0: bridge window [io 0x1000-0x1fff]
    [ 0.224895] pci 0000:00:1e.0: bridge window [mem 0x53100000-0x531fffff]
    [ 0.224959] pci 0000:00:1e.0: setting latency timer to 64
    [ 0.224966] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
    [ 0.224969] pci_bus 0000:00: resource 5 [mem 0x00000000-0xffffffff]
    [ 0.224974] pci_bus 0000:01: resource 0 [io 0x3000-0x3fff]
    [ 0.224977] pci_bus 0000:01: resource 1 [mem 0x52000000-0x530fffff]
    [ 0.224980] pci_bus 0000:01: resource 2 [mem 0x40000000-0x51ffffff pref]
    [ 0.224984] pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
    [ 0.224987] pci_bus 0000:02: resource 1 [mem 0x53200000-0x532fffff]
    [ 0.224990] pci_bus 0000:02: resource 2 [mem 0x53700000-0x539fffff pref]
    [ 0.224994] pci_bus 0000:03: resource 0 [io 0x5000-0x5fff]
    [ 0.224997] pci_bus 0000:03: resource 1 [mem 0x53400000-0x534fffff]
    [ 0.225001] pci_bus 0000:03: resource 2 [mem 0x53a00000-0x53bfffff 64bit pref]
    [ 0.225004] pci_bus 0000:04: resource 0 [io 0x6000-0x6fff]
    [ 0.225007] pci_bus 0000:04: resource 1 [mem 0x53500000-0x535fffff]
    [ 0.225011] pci_bus 0000:04: resource 2 [mem 0x53c00000-0x53dfffff 64bit pref]
    [ 0.225014] pci_bus 0000:05: resource 0 [io 0x7000-0x7fff]
    [ 0.225018] pci_bus 0000:05: resource 1 [mem 0x53600000-0x536fffff]
    [ 0.225021] pci_bus 0000:05: resource 2 [mem 0x53e00000-0x53ffffff 64bit pref]
    [ 0.225025] pci_bus 0000:06: resource 0 [io 0x1000-0x1fff]
    [ 0.225028] pci_bus 0000:06: resource 1 [mem 0x53100000-0x531fffff]
    [ 0.225031] pci_bus 0000:06: resource 4 [io 0x0000-0xffff]
    [ 0.225035] pci_bus 0000:06: resource 5 [mem 0x00000000-0xffffffff]
    [ 0.225091] NET: Registered protocol family 2
    [ 0.225171] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    [ 0.225391] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
    [ 0.225895] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
    [ 0.226187] TCP: Hash tables configured (established 131072 bind 65536)
    [ 0.226190] TCP: reno registered
    [ 0.226195] UDP hash table entries: 512 (order: 2, 16384 bytes)
    [ 0.226208] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
    [ 0.226329] NET: Registered protocol family 1
    [ 0.226637] pci 0000:01:00.0: Boot video device
    [ 0.226698] pci 0000:06:08.0: Firmware left e100 interrupts enabled; disabling
    [ 0.226709] PCI: CLS 0 bytes, default 64
    [ 0.226780] Unpacking initramfs...
    [ 0.315303] Freeing initrd memory: 2900k freed
    [ 0.317191] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
    [ 0.317195] apm: disabled - APM is not SMP safe.
    [ 0.317515] audit: initializing netlink socket (disabled)
    [ 0.317533] type=2000 audit(1342552654.316:1): initialized
    [ 0.317976] highmem bounce pool size: 64 pages
    [ 0.317984] HugeTLB registered 4 MB page size, pre-allocated 0 pages
    [ 0.320723] VFS: Disk quotas dquot_6.5.2
    [ 0.320797] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    [ 0.320931] msgmni has been set to 1740
    [ 0.321235] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
    [ 0.321282] io scheduler noop registered
    [ 0.321287] io scheduler deadline registered
    [ 0.321299] io scheduler cfq registered (default)
    [ 0.321473] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
    [ 0.321588] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
    [ 0.321708] pcieport 0000:00:1c.1: irq 42 for MSI/MSI-X
    [ 0.321830] pcieport 0000:00:1c.2: irq 43 for MSI/MSI-X
    [ 0.321950] pcieport 0000:00:1c.3: irq 44 for MSI/MSI-X
    [ 0.322243] GHES: HEST is not enabled!
    [ 0.322264] isapnp: Scanning for PnP cards...
    [ 0.678327] isapnp: No Plug & Play device found
    [ 0.678412] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.698985] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [ 0.720023] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [ 0.720384] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
    [ 0.723503] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 0.723558] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 0.723755] mousedev: PS/2 mouse device common for all mice
    [ 0.723869] rtc_cmos 00:03: RTC can wake from S4
    [ 0.724031] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
    [ 0.724060] rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
    [ 0.724098] cpuidle: using governor ladder
    [ 0.724101] cpuidle: using governor menu
    [ 0.724316] TCP: cubic registered
    [ 0.724489] NET: Registered protocol family 10
    [ 0.724741] NET: Registered protocol family 17
    [ 0.724748] Registering the dns_resolver key type
    [ 0.724796] Using IPI No-Shortcut mode
    [ 0.724971] PM: Hibernation image not present or could not be loaded.
    [ 0.724985] registered taskstats version 1
    [ 0.725540] rtc_cmos 00:03: setting system clock to 2012-07-17 19:17:35 UTC (1342552655)
    [ 0.725588] Initializing network drop monitor service
    [ 0.726860] Freeing unused kernel memory: 524k freed
    [ 0.727195] Write protecting the kernel text: 3812k
    [ 0.727226] Write protecting the kernel read-only data: 1120k
    [ 0.740567] systemd-udevd[41]: starting version 186
    [ 0.742721] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    [ 0.745749] SCSI subsystem initialized
    [ 0.749328] libata version 3.00 loaded.
    [ 0.750857] ahci 0000:02:00.0: version 3.0
    [ 0.750961] ahci 0000:02:00.0: irq 45 for MSI/MSI-X
    [ 0.751021] ahci: SSS flag set, parallel bus scan disabled
    [ 0.751069] ahci 0000:02:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
    [ 0.751077] ahci 0000:02:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs
    [ 0.752850] scsi0 : ahci
    [ 0.753200] scsi1 : ahci
    [ 0.753383] ata1: SATA max UDMA/133 abar m512@0x53200000 port 0x53200100 irq 45
    [ 0.753391] ata2: SATA max UDMA/133 abar m512@0x53200000 port 0x53200180 irq 45
    [ 1.240043] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
    [ 1.252105] ata1.00: ATA-8: OCZ-SOLID3, 2.15, max UDMA/133
    [ 1.252110] ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
    [ 1.262069] ata1.00: configured for UDMA/133
    [ 1.262262] scsi 0:0:0:0: Direct-Access ATA OCZ-SOLID3 2.15 PQ: 0 ANSI: 5
    [ 1.264029] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
    [ 1.264196] sd 0:0:0:0: [sda] Write Protect is off
    [ 1.264203] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 1.264257] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 1.265654] sda: sda1 sda2 sda3 sda4
    [ 1.266383] sd 0:0:0:0: [sda] Attached SCSI disk
    [ 1.320034] Refined TSC clocksource calibration: 2999.980 MHz.
    [ 1.320041] Switching to clocksource tsc
    [ 1.746702] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
    [ 1.747318] ata2.00: ATA-8: ST3000DM001-9YN166, CC4C, max UDMA/133
    [ 1.747323] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
    [ 1.747889] ata2.00: configured for UDMA/133
    [ 1.748030] scsi 1:0:0:0: Direct-Access ATA ST3000DM001-9YN1 CC4C PQ: 0 ANSI: 5
    [ 1.748540] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
    [ 1.748547] sd 1:0:0:0: [sdb] 4096-byte physical blocks
    [ 1.748667] sd 1:0:0:0: [sdb] Write Protect is off
    [ 1.748674] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
    [ 1.748725] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 1.793835] sdb: sdb1
    [ 1.794347] sd 1:0:0:0: [sdb] Attached SCSI disk
    [ 1.892420] usbcore: registered new interface driver usbfs
    [ 1.892471] usbcore: registered new interface driver hub
    [ 1.895559] ata_piix 0000:00:1f.1: version 2.13
    [ 1.895639] ata_piix 0000:00:1f.1: setting latency timer to 64
    [ 1.897473] usbcore: registered new device driver usb
    [ 1.898382] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 1.898429] scsi2 : ata_piix
    [ 1.899754] scsi3 : ata_piix
    [ 1.900600] ata3: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x40b0 irq 14
    [ 1.900605] ata4: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x40b8 irq 15
    [ 1.900676] ata4: port disabled--ignoring
    [ 1.901417] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
    [ 1.901473] ata_piix 0000:00:1f.2: setting latency timer to 64
    [ 1.904508] scsi4 : ata_piix
    [ 1.905087] scsi5 : ata_piix
    [ 1.905220] ata5: SATA max UDMA/133 cmd 0x40c8 ctl 0x40e4 bmdma 0x40a0 irq 19
    [ 1.905227] ata6: SATA max UDMA/133 cmd 0x40c0 ctl 0x40e0 bmdma 0x40a8 irq 19
    [ 1.905347] ehci_hcd 0000:00:1d.7: setting latency timer to 64
    [ 1.905355] ehci_hcd 0000:00:1d.7: EHCI Host Controller
    [ 1.905401] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
    [ 1.905444] ehci_hcd 0000:00:1d.7: debug port 1
    [ 1.905558] uhci_hcd: USB Universal Host Controller Interface driver
    [ 1.909355] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
    [ 1.909393] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x53304000
    [ 1.916865] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    [ 1.917873] hub 1-0:1.0: USB hub found
    [ 1.917883] hub 1-0:1.0: 8 ports detected
    [ 1.918079] uhci_hcd 0000:00:1d.0: setting latency timer to 64
    [ 1.918087] uhci_hcd 0000:00:1d.0: UHCI Host Controller
    [ 1.918109] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
    [ 1.918149] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00004080
    [ 1.918445] hub 2-0:1.0: USB hub found
    [ 1.918456] hub 2-0:1.0: 2 ports detected
    [ 1.918663] uhci_hcd 0000:00:1d.1: setting latency timer to 64
    [ 1.918671] uhci_hcd 0000:00:1d.1: UHCI Host Controller
    [ 1.918692] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
    [ 1.918728] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00004060
    [ 1.919043] hub 3-0:1.0: USB hub found
    [ 1.919053] hub 3-0:1.0: 2 ports detected
    [ 1.919306] uhci_hcd 0000:00:1d.2: setting latency timer to 64
    [ 1.919314] uhci_hcd 0000:00:1d.2: UHCI Host Controller
    [ 1.919338] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
    [ 1.919391] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00004040
    [ 1.919771] hub 4-0:1.0: USB hub found
    [ 1.919781] hub 4-0:1.0: 2 ports detected
    [ 1.920058] uhci_hcd 0000:00:1d.3: setting latency timer to 64
    [ 1.920066] uhci_hcd 0000:00:1d.3: UHCI Host Controller
    [ 1.920085] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
    [ 1.920162] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00004020
    [ 1.920720] hub 5-0:1.0: USB hub found
    [ 1.920731] hub 5-0:1.0: 2 ports detected
    [ 2.068266] ata6.00: ATA-6: WDC WD2000JD-00HBB0, 08.02D08, max UDMA/133
    [ 2.068272] ata6.00: 390721968 sectors, multi 16: LBA48
    [ 2.074099] ata5.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133
    [ 2.074104] ata5.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
    [ 2.081454] ata6.00: configured for UDMA/133
    [ 2.100167] ata5.01: ATA-8: ST3500418AS, CC34, max UDMA/133
    [ 2.100172] ata5.01: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
    [ 2.107102] ata5.00: configured for UDMA/133
    [ 2.162850] ata5.01: configured for UDMA/133
    [ 2.173642] ata3.00: ATAPI: SONY DVD RW DRU-530A, 2.1g, max UDMA/33
    [ 2.173649] ata3.01: ATAPI: LITE-ON DVDRW SOHW-1633S, BGS4, max UDMA/66
    [ 2.173654] ata3.01: limited to UDMA/33 due to 40-wire cable
    [ 2.186862] ata3.00: configured for UDMA/33
    [ 2.200194] ata3.01: configured for UDMA/33
    [ 2.201725] scsi 2:0:0:0: CD-ROM SONY DVD RW DRU-530A 2.1g PQ: 0 ANSI: 5
    [ 2.202839] scsi 2:0:1:0: CD-ROM LITE-ON DVDRW SOHW-1633S BGS4 PQ: 0 ANSI: 5
    [ 2.203271] scsi 4:0:0:0: Direct-Access ATA WDC WD20EARX-00P 51.0 PQ: 0 ANSI: 5
    [ 2.203548] sd 4:0:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
    [ 2.203557] sd 4:0:0:0: [sdc] 4096-byte physical blocks
    [ 2.203683] sd 4:0:0:0: [sdc] Write Protect is off
    [ 2.203690] sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
    [ 2.203749] sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.203803] scsi 4:0:1:0: Direct-Access ATA ST3500418AS CC34 PQ: 0 ANSI: 5
    [ 2.204553] scsi 5:0:0:0: Direct-Access ATA WDC WD2000JD-00H 08.0 PQ: 0 ANSI: 5
    [ 2.204737] sd 4:0:1:0: [sdd] 976773168 512-byte logical blocks: (500 GB/465 GiB)
    [ 2.204849] sd 5:0:0:0: [sde] 390721968 512-byte logical blocks: (200 GB/186 GiB)
    [ 2.204969] sd 5:0:0:0: [sde] Write Protect is off
    [ 2.204976] sd 5:0:0:0: [sde] Mode Sense: 00 3a 00 00
    [ 2.205029] sd 5:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.223374] usb 1-2: new high-speed USB device number 2 using ehci_hcd
    [ 2.225847] sdc: sdc1
    [ 2.225864] sd 4:0:1:0: [sdd] Write Protect is off
    [ 2.225872] sd 4:0:1:0: [sdd] Mode Sense: 00 3a 00 00
    [ 2.225944] sd 4:0:1:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.226606] sd 4:0:0:0: [sdc] Attached SCSI disk
    [ 2.242524] sdd: sdd1
    [ 2.243011] sd 4:0:1:0: [sdd] Attached SCSI disk
    [ 2.250598] sde: sde2 sde3 < sde5 sde6 >
    [ 2.251325] sd 5:0:0:0: [sde] Attached SCSI disk
    [ 2.263852] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
    [ 2.263860] cdrom: Uniform CD-ROM driver Revision: 3.20
    [ 2.265692] sr 2:0:0:0: Attached scsi CD-ROM sr0
    [ 2.269125] sr1: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
    [ 2.270115] sr 2:0:1:0: Attached scsi CD-ROM sr1
    [ 2.453377] usb 1-3: new high-speed USB device number 3 using ehci_hcd
    [ 2.630176] input: Western Digital My Book as /devices/pci0000:00/0000:00:1d.7/usb1/1-3/1-3:1.1/input/input1
    [ 2.630296] generic-usb 0003:1058:1102.0001: input,hidraw0: USB HID v1.11 Device [Western Digital My Book] on usb-0000:00:1d.7-3/input1
    [ 2.630361] usbcore: registered new interface driver usbhid
    [ 2.630366] usbhid: USB HID core driver
    [ 2.720033] usb 1-5: new high-speed USB device number 4 using ehci_hcd
    [ 2.992001] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
    [ 3.123459] usb 5-1: new low-speed USB device number 2 using uhci_hcd
    [ 3.170371] systemd[1]: systemd 186 running in system mode. (+PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP; arch)
    [ 3.189960] systemd[1]: Inserted module 'autofs4'
    [ 3.190421] systemd[1]: Set hostname to <bbq>.
    [ 3.347408] systemd[1]: Cannot add dependency job for unit exportfs.service, ignoring: Unit exportfs.service failed to load: No such file or directory. See system logs and 'systemctl status exportfs.service' for details.
    [ 3.347444] systemd[1]: Cannot add dependency job for unit arch-daemons.target, ignoring: Unit arch-daemons.target failed to load: No such file or directory. See system logs and 'systemctl status arch-daemons.target' for details.
    [ 3.347509] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory. See system logs and 'systemctl status display-manager.service' for details.
    [ 3.600924] systemd-readahead[134]: Bumped block_nr parameter of 8:0 to 16384. This is a temporary hack and should be removed one day.
    [ 3.890242] systemd-udevd[139]: starting version 186
    [ 3.928976] systemd-journald[146]: Fixed max_use=50.2M max_size=6.2M min_size=64.0K keep_free=25.1M
    [ 3.929449] systemd-journald[146]: Vacuuming...
    [ 4.016020] FS-Cache: Loaded
    [ 4.026904] RPC: Registered named UNIX socket transport module.
    [ 4.026909] RPC: Registered udp transport module.
    [ 4.026912] RPC: Registered tcp transport module.
    [ 4.026914] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [ 4.068138] EXT4-fs (sda1): re-mounted. Opts: (null)
    [ 4.071885] NFS: Registering the id_resolver key type
    [ 4.071920] FS-Cache: Netfs 'nfs' registered for caching
    [ 4.090493] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
    [ 4.103300] Installing knfsd (copyright (C) 1996 [email protected]).
    [ 4.106821] ACPI: Sleep Button [SLPB]
    [ 4.114494] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
    [ 4.114509] ACPI: Power Button [PWRF]
    [ 4.135074] parport_pc 00:07: reported by Plug and Play ACPI
    [ 4.135106] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
    [ 4.157067] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
    [ 4.178255] Linux agpgart interface v0.103
    [ 4.202375] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input4
    [ 4.203197] hda_intel: Disabling MSI
    [ 4.255263] intel_rng: Firmware space is locked read-only. If you can't or
    [ 4.255267] intel_rng: don't want to disable this in firmware setup, and if
    [ 4.255271] intel_rng: you are certain that your system has a functional
    [ 4.255274] intel_rng: RNG, try using the 'no_fwh_detect' option.
    [ 4.273750] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
    [ 4.273757] e100: Copyright(c) 1999-2006 Intel Corporation
    [ 4.274079] iTCO_vendor_support: vendor-support=0
    [ 4.285411] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
    [ 4.285661] iTCO_wdt: Found a ICH6 or ICH6R TCO device (Version=2, TCOBASE=0x0460)
    [ 4.285769] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 4.380102] usbcore: registered new interface driver uas
    [ 4.415911] Initializing USB Mass Storage driver...
    [ 4.423630] scsi6 : usb-storage 1-3:1.0
    [ 4.423883] usbcore: registered new interface driver usb-storage
    [ 4.423888] USB Mass Storage support registered.
    [ 4.426642] e100 0000:06:08.0: eth0: addr 0x53100000, irq 20, MAC addr 00:11:11:9d:19:91
    [ 4.434273] scsi7 : usb-storage 1-5:1.0
    [ 4.434499] usbcore: registered new interface driver ums-cypress
    [ 4.475410] psmouse serio1: hgpk: ID: 10 00 64
    [ 4.480175] firewire_ohci 0000:06:05.0: added OHCI v1.0 device as card 0, 8 IR + 8 IT contexts, quirks 0x0
    [ 4.487522] microcode: CPU0 sig=0xf41, pf=0x10, revision=0xd
    [ 4.506728] Registered IR keymap rc-ati-x10
    [ 4.507019] input: X10 Wireless Technology Inc USB Receiver as /devices/pci0000:00/0000:00:1d.3/usb5/5-1/5-1:1.0/rc/rc0/input5
    [ 4.507357] rc0: X10 Wireless Technology Inc USB Receiver as /devices/pci0000:00/0000:00:1d.3/usb5/5-1/5-1:1.0/rc/rc0
    [ 4.507587] input: X10 Wireless Technology Inc USB Receiver mouse as /devices/pci0000:00/0000:00:1d.3/usb5/5-1/5-1:1.0/input/input6
    [ 4.507783] usbcore: registered new interface driver ati_remote
    [ 4.530507] psmouse serio1: logips2pp: Detected unknown Logitech mouse model 127
    [ 4.687581] ppdev: user-space parallel port driver
    [ 4.761362] Adding 1047928k swap on /dev/sda2. Priority:-1 extents:1 across:1047928k SS
    [ 4.804984] microcode: CPU1 sig=0xf41, pf=0x10, revision=0xd
    [ 4.814875] nvidia: module license 'NVIDIA' taints kernel.
    [ 4.814882] Disabling lock debugging due to kernel taint
    [ 4.822000] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
    [ 4.926478] fuse init (API version 7.18)
    [ 4.970217] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input7
    [ 4.971016] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input8
    [ 4.971676] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input9
    [ 4.971943] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input10
    [ 4.980870] firewire_core 0000:06:05.0: created device fw0: GUID 00111100009d1991, S400
    [ 4.981627] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
    [ 4.982035] NVRM: loading NVIDIA UNIX x86 Kernel Module 302.17 Tue Jun 12 18:37:51 PDT 2012
    [ 5.031213] input: ImExPS/2 Logitech Explorer Mouse as /devices/platform/i8042/serio1/input/input11
    [ 5.432483] scsi 6:0:0:0: Direct-Access WD My Book 1028 PQ: 0 ANSI: 4
    [ 5.436924] sd 6:0:0:0: [sdf] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
    [ 5.437226] scsi 7:0:0:0: Direct-Access WDC WD25 00JB-00GVA0 PQ: 0 ANSI: 0
    [ 5.438100] sd 7:0:0:0: [sdg] 488397168 512-byte logical blocks: (250 GB/232 GiB)
    [ 5.439101] sd 7:0:0:0: [sdg] Write Protect is off
    [ 5.439109] sd 7:0:0:0: [sdg] Mode Sense: 33 00 00 00
    [ 5.439482] sd 6:0:0:0: [sdf] Write Protect is off
    [ 5.439489] sd 6:0:0:0: [sdf] Mode Sense: 10 00 00 00
    [ 5.440101] sd 7:0:0:0: [sdg] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
    [ 5.442224] sd 6:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 5.463763] sdg: sdg1 sdg2
    [ 5.467100] sd 7:0:0:0: [sdg] Attached SCSI disk
    [ 5.469267] sdf: sdf1
    [ 5.491846] sd 6:0:0:0: [sdf] Attached SCSI disk
    [ 36.480046] usb 1-5: reset high-speed USB device number 4 using ehci_hcd
    [ 37.347138] systemd-journald[146]: Fixed max_use=1.4G max_size=128.0M min_size=64.0K keep_free=765.3M
    [ 37.347165] systemd-journald[146]: Flushing to /var...
    [ 37.837240] EXT4-fs (sdf1): mounted filesystem with ordered data mode. Opts: (null)
    [ 37.906826] EXT4-fs (sdg2): mounted filesystem with ordered data mode. Opts: (null)
    [ 38.068461] EXT4-fs (sde6): mounted filesystem with ordered data mode. Opts: (null)
    [ 38.194403] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
    [ 38.740678] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
    [ 38.747081] EXT4-fs (sdd1): mounted filesystem with ordered data mode. Opts: (null)
    [ 39.486016] ip_tables: (C) 2000-2006 Netfilter Core Team
    [ 39.599796] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
    [ 39.600119] NFSD: starting 90-second grace period
    [ 40.579508] Netfilter messages via NETLINK v0.30.
    [ 40.594917] nf_conntrack version 0.5.0 (16078 buckets, 64312 max)
    [ 40.746099] ip6_tables: (C) 2000-2006 Netfilter Core Team
    [ 40.747318] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
    [ 40.747325] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
    [ 40.786415] ctnetlink v0.93: registering with nfnetlink.
    [ 40.886321] ip_set: protocol 6
    [ 40.898284] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
    [ 41.762042] xt_time: kernel timezone is -0000
    [ 42.318176] Bridge firewalling registered
    [ 42.704278] u32 classifier
    [ 42.704284] input device check on
    [ 42.704287] Actions configured
    [ 43.154527] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 43.156826] e100 0000:06:08.0: eth0: NIC Link is Up 100 Mbps Full Duplex
    [ 43.157214] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [ 44.557798] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
    [ 44.872612] [drm] Initialized drm 1.1.0 20060810
    [ 44.881629] wmi: Mapper loaded
    [ 51.096207] zram: module is from the staging directory, the quality is unknown, you have been warned.
    [ 51.105163] zram: Unknown parameter `zram_num_devices'
    [ 51.148183] zram: module is from the staging directory, the quality is unknown, you have been warned.
    [ 51.148690] zram: Creating 2 devices ...
    [ 51.398897] Adding 514496k swap on /dev/zram0. Priority:100 extents:1 across:514496k SS
    [ 51.406500] Adding 514496k swap on /dev/zram1. Priority:100 extents:1 across:514496k SS
    [ 76.005728] bootchart-collector started as pid 1586 with 2 args: '--dump' '/tmp/bootchart.94K3Fb6yom'
    [ 76.005734] Extracting profile data from pid 178
    [ 76.005736] map 0xbfe14000 -> 0xbfe35000 size: 132k from 'bfe14000' 'bfe35000'
    [ 76.005739] read 135168 bytes of 135168
    [ 76.005741] reading 101 chunks (of 101) ... wrote 12527 kb
    [ 76.005743] bootchart-collector pid: 1586 unmounted proc / clean exit
    Linux 3.3.8-1, Nvidia 295.49-1 Dmesg Output
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Linux version 3.3.8-1-ARCH (tobias@T-POWA-LX) (gcc version 4.7.0 20120505 (prerelease) (GCC) ) #1 SMP PREEMPT Tue Jun 5 13:24:07 UTC 2012
    [ 0.000000] BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
    [ 0.000000] BIOS-e820: 0000000000100000 - 000000003fe54000 (usable)
    [ 0.000000] BIOS-e820: 000000003fe54000 - 000000003fee8000 (ACPI NVS)
    [ 0.000000] BIOS-e820: 000000003fee8000 - 000000003ff00000 (ACPI data)
    [ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
    [ 0.000000] DMI 2.3 present.
    [ 0.000000] DMI: 507GR /D915GAG, BIOS AG91510J.15A.0816.2005.0214.1818 02/14/2005
    [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
    [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
    [ 0.000000] last_pfn = 0x3fe54 max_arch_pfn = 0x100000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-FFFFF uncachable
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 000000000 mask FC0000000 write-back
    [ 0.000000] 1 base 03FF00000 mask FFFF00000 uncachable
    [ 0.000000] 2 disabled
    [ 0.000000] 3 disabled
    [ 0.000000] 4 disabled
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] found SMP MP-table at [c00fe650] fe650
    [ 0.000000] initial memory mapped : 0 - 00c00000
    [ 0.000000] Base memory trampoline at [c009a000] 9a000 size 16384
    [ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
    [ 0.000000] 0000000000 - 0000400000 page 4k
    [ 0.000000] 0000400000 - 0037400000 page 2M
    [ 0.000000] 0037400000 - 00377fe000 page 4k
    [ 0.000000] kernel direct mapping tables up to 377fe000 @ bfb000-c00000
    [ 0.000000] RAMDISK: 3fb70000 - 3fe44000
    [ 0.000000] Allocated new RAMDISK: 3752a000 - 377fd833
    [ 0.000000] Move RAMDISK from 000000003fb70000 - 000000003fe43832 to 3752a000 - 377fd832
    [ 0.000000] ACPI: RSDP 000fe020 00014 (v00 GATEWA)
    [ 0.000000] ACPI: RSDT 3fefde48 00038 (v01 GATEWA 04DT037 00000330 MSFT 01000013)
    [ 0.000000] ACPI: FACP 3fefcf10 00074 (v01 GATEWA 04DT037 00000330 MSFT 01000013)
    [ 0.000000] ACPI: DSDT 3fef8010 0339C (v01 GATEWA 04DT037 00000330 MSFT 01000013)
    [ 0.000000] ACPI: FACS 3fee5c40 00040
    [ 0.000000] ACPI: APIC 3fefce10 00068 (v01 GATEWA 04DT037 00000330 MSFT 01000013)
    [ 0.000000] ACPI: WDDT 3fef7f90 00040 (v01 GATEWA 04DT037 00000330 MSFT 01000013)
    [ 0.000000] ACPI: MCFG 3fef7f10 0003C (v01 GATEWA 04DT037 00000330 MSFT 01000013)
    [ 0.000000] ACPI: SSDT 3fef6d90 00124 (v01 GATEWA CpuPm 00000330 MSFT 01000013)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] 134MB HIGHMEM available.
    [ 0.000000] 887MB LOWMEM available.
    [ 0.000000] mapped low ram: 0 - 377fe000
    [ 0.000000] low ram: 0 - 377fe000
    [ 0.000000] Zone PFN ranges:
    [ 0.000000] DMA 0x00000010 -> 0x00001000
    [ 0.000000] Normal 0x00001000 -> 0x000377fe
    [ 0.000000] HighMem 0x000377fe -> 0x0003fe54
    [ 0.000000] Movable zone start PFN for each node
    [ 0.000000] Early memory PFN ranges
    [ 0.000000] 0: 0x00000010 -> 0x0000009f
    [ 0.000000] 0: 0x00000100 -> 0x0003fe54
    [ 0.000000] On node 0 totalpages: 261603
    [ 0.000000] free_area_init_node: node 0, pgdat c060c580, node_mem_map f6d29200
    [ 0.000000] DMA zone: 32 pages used for memmap
    [ 0.000000] DMA zone: 0 pages reserved
    [ 0.000000] DMA zone: 3951 pages, LIFO batch:0
    [ 0.000000] Normal zone: 1744 pages used for memmap
    [ 0.000000] Normal zone: 221486 pages, LIFO batch:31
    [ 0.000000] HighMem zone: 269 pages used for memmap
    [ 0.000000] HighMem zone: 34121 pages, LIFO batch:7
    [ 0.000000] Using APIC driver default
    [ 0.000000] ACPI: PM-Timer IO Port: 0x408
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
    [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
    [ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
    [ 0.000000] Allocating PCI resources starting at 3ff00000 (gap: 3ff00000:c0100000)
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 13 pages/cpu @f6d08000 s30848 r0 d22400 u53248
    [ 0.000000] pcpu-alloc: s30848 r0 d22400 u53248 alloc=13*4096
    [ 0.000000] pcpu-alloc: [0] 0 [0] 1
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259558
    [ 0.000000] Kernel command line: root=/dev/disk/by-uuid/10f8033d-8fe9-46be-bccf-68a14025bbaa ro init=/bin/systemd
    [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
    [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    [ 0.000000] Initializing CPU#0
    [ 0.000000] allocated 2093600 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] Initializing HighMem for node 0 (000377fe:0003fe54)
    [ 0.000000] Memory: 1025660k/1046864k available (3774k kernel code, 20752k reserved, 1434k data, 520k init, 137560k highmem)
    [ 0.000000] virtual kernel memory layout:
    [ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
    [ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    [ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
    [ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
    [ 0.000000] .init : 0xc0617000 - 0xc0699000 ( 520 kB)
    [ 0.000000] .data : 0xc04af9a9 - 0xc0616400 (1434 kB)
    [ 0.000000] .text : 0xc0100000 - 0xc04af9a9 (3774 kB)
    [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
    [ 0.000000] SLUB: Genslabs=15, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Verbose stalled-CPUs detection is disabled.
    [ 0.000000] NR_IRQS:2304 nr_irqs:512 16
    [ 0.000000] CPU 0 irqstacks, hard=f6408000 soft=f640a000
    [ 0.000000] Console: colour VGA+ 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] Fast TSC calibration using PIT
    [ 0.000000] Detected 3000.097 MHz processor.
    [ 0.006668] Calibrating delay loop (skipped), value calculated using timer frequency.. 6002.20 BogoMIPS (lpj=10000323)
    [ 0.006674] pid_max: default: 32768 minimum: 301
    [ 0.006706] Security Framework initialized
    [ 0.006712] AppArmor: AppArmor disabled by boot time parameter
    [ 0.006735] Mount-cache hash table entries: 512
    [ 0.006921] Initializing cgroup subsys cpuacct
    [ 0.006925] Initializing cgroup subsys memory
    [ 0.006936] Initializing cgroup subsys devices
    [ 0.006939] Initializing cgroup subsys freezer
    [ 0.006942] Initializing cgroup subsys net_cls
    [ 0.006945] Initializing cgroup subsys blkio
    [ 0.006989] CPU: Physical Processor ID: 0
    [ 0.006992] CPU: Processor Core ID: 0
    [ 0.006995] mce: CPU supports 4 MCE banks
    [ 0.007009] CPU0: Thermal monitoring enabled (TM1)
    [ 0.007014] using mwait in idle threads.
    [ 0.010636] ACPI: Core revision 20120111
    [ 0.013347] ftrace: allocating 16622 entries in 33 pages
    [ 0.020077] Enabling APIC mode: Flat. Using 1 I/O APICs
    [ 0.020459] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.054563] CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 01
    [ 0.056663] Performance Events: Netburst events, Netburst P4/Xeon PMU driver.
    [ 0.056663] ... version: 0
    [ 0.056663] ... bit width: 40
    [ 0.056663] ... generic registers: 18
    [ 0.056663] ... value mask: 000000ffffffffff
    [ 0.056663] ... max period: 0000007fffffffff
    [ 0.056663] ... fixed-purpose events: 0
    [ 0.056663] ... event mask: 000000000003ffff
    [ 0.073415] NMI watchdog enabled, takes one hw-pmu counter.
    [ 0.100018] CPU 1 irqstacks, hard=f64a4000 soft=f64a6000
    [ 0.100021] Booting Node 0, Processors #1 Ok.
    [ 0.100025] smpboot cpu 1: start_ip = 9a000
    [ 0.009999] Initializing CPU#1
    [ 0.113372] NMI watchdog enabled, takes one hw-pmu counter.
    [ 0.120000] Brought up 2 CPUs
    [ 0.120006] Total of 2 processors activated (12005.40 BogoMIPS).
    [ 0.120978] devtmpfs: initialized
    [ 0.120978] PM: Registering ACPI NVS region at 3fe54000 (606208 bytes)
    [ 0.120978] NET: Registered protocol family 16
    [ 0.120978] ACPI: bus type pci registered
    [ 0.120978] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.120978] PCI: not using MMCONFIG
    [ 0.123293] PCI: Using configuration type 1 for base access
    [ 0.126717] bio: create slab <bio-0> at 0
    [ 0.126739] ACPI: Added _OSI(Module Device)
    [ 0.126739] ACPI: Added _OSI(Processor Device)
    [ 0.126739] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.126739] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.127496] ACPI: EC: Look up EC in DSDT
    [ 0.127496] ACPI: Interpreter enabled
    [ 0.127496] ACPI: (supports S0 S1 S3 S4 S5)
    [ 0.127496] ACPI: Using IOAPIC for interrupt routing
    [ 0.127496] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.127496] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
    [ 0.127496] PCI: Using MMCONFIG for extended config space
    [ 0.131872] ACPI: No dock devices found.
    [ 0.131883] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
    [ 0.133334] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.136111] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
    [ 0.136116] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
    [ 0.136120] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
    [ 0.136123] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000fffff] (ignored)
    [ 0.136127] pci_root PNP0A03:00: host bridge window [mem 0xf0000000-0xfbffffff] (ignored)
    [ 0.136131] pci_root PNP0A03:00: host bridge window [mem 0x40000000-0xe0000000] (ignored)
    [ 0.136134] PCI: root bus 00: using default resources
    [ 0.136196] PCI host bridge to bus 0000:00
    [ 0.136201] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
    [ 0.136206] pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
    [ 0.136220] pci 0000:00:00.0: [8086:2580] type 0 class 0x000600
    [ 0.136283] pci 0000:00:01.0: [8086:2581] type 1 class 0x000604
    [ 0.136340] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
    [ 0.13639

    And here is the output of alsa-info.sh which I have also added to the original post:
    upload=true&script=true&cardinfo=
    !!ALSA Information Script v 0.4.61
    !!Script ran on: Wed Jul 18 00:10:56 UTC 2012
    !!Linux Distribution
    Arch Linux \r (\l) DISTRIB_ID=archlinux DISTRIB_DESCRIPTION="Arch Linux" NAME="Arch Linux" ID=arch PRETTY_NAME="Arch Linux" HOME_URL="http://www.archlinux.org/" SUPPORT_URL="https://bbs.archlinux.org/" BUG_REPORT_URL="https://bugs.archlinux.org/"
    !!DMI Information
    Manufacturer:
    Product Name: 507GR
    Product Version:
    Firmware Version: AG91510J.15A.0816.2005.0214.1818
    !!Kernel Information
    Kernel release: 3.4.4-3-ARCH
    Operating System: GNU/Linux
    Architecture: i686
    Processor: unknown
    SMP Enabled: Yes
    !!ALSA Version
    Driver version: 1.0.25
    Library version: 1.0.25
    Utilities version: 1.0.25
    !!Loaded ALSA modules
    snd_hda_intel
    snd_hda_intel
    !!Sound Servers on this system
    Jack:
    Installed - Yes (/usr/bin/jackd)
    Running - No
    !!Soundcards recognised by ALSA
    0 [Intel ]: HDA-Intel - HDA Intel
    HDA Intel at 0x53300000 irq 46
    1 [NVidia ]: HDA-Intel - HDA NVidia
    HDA NVidia at 0x53000000 irq 17
    !!PCI Soundcards installed in the system
    00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03)
    01:00.1 Audio device: NVIDIA Corporation High Definition Audio Controller (rev a1)
    !!Advanced information - PCI Vendor/Device/Subsystem ID's
    00:1b.0 0403: 8086:2668 (rev 03)
    Subsystem: 107b:4037
    01:00.1 0403: 10de:0be3 (rev a1)
    Subsystem: 1043:8354
    !!Loaded sound module options
    !!Module: snd_hda_intel
    align_buffer_size : -1
    bdl_pos_adj : 1,32,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
    beep_mode : 1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1
    enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y
    enable_msi : -1
    id : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
    index : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
    model : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
    patch : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
    position_fix : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
    power_save : 0
    power_save_controller : Y
    probe_mask : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
    probe_only : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
    single_cmd : N
    snoop : Y
    !!Module: snd_hda_intel
    align_buffer_size : -1
    bdl_pos_adj : 1,32,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
    beep_mode : 1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1
    enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y
    enable_msi : -1
    id : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
    index : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
    model : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
    patch : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
    position_fix : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
    power_save : 0
    power_save_controller : Y
    probe_mask : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
    probe_only : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
    single_cmd : N
    snoop : Y
    !!HDA-Intel Codec information
    --startcollapse--
    Codec: Realtek ALC880
    Address: 2
    AFG Function Id: 0x1 (unsol 0)
    Vendor Id: 0x10ec0880
    Subsystem Id: 0x08600000
    Revision Id: 0x90000
    No Modem Function Group found
    Default PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
    Default Amp-In caps: N/A
    Default Amp-Out caps: N/A
    GPIO: io=2, o=0, i=0, unsolicited=1, wake=0
    IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
    IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
    Node 0x02 [Audio Output] wcaps 0x411: Stereo
    Converter: stream=0, channel=0
    PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
    Power states: D0 D1 D2 D3
    Power: setting=D0, actual=D0
    Node 0x03 [Audio Output] wcaps 0x411: Stereo
    Converter: stream=0, channel=0
    PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
    Power states: D0 D1 D2 D3
    Power: setting=D0, actual=D0
    Node 0x04 [Audio Output] wcaps 0x411: Stereo
    Converter: stream=0, channel=0
    PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
    Power states: D0 D1 D2 D3
    Power: setting=D0, actual=D0
    Node 0x05 [Audio Output] wcaps 0x411: Stereo
    Converter: stream=0, channel=0
    PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
    Power states: D0 D1 D2 D3
    Power: setting=D0, actual=D0
    Node 0x06 [Audio Output] wcaps 0x211: Stereo Digital
    Converter: stream=0, channel=0
    Digital:
    Digital category: 0x0
    PCM:
    rates [0x160]: 44100 48000 96000
    bits [0x1e]: 16 20 24 32
    formats [0x1]: PCM
    Node 0x07 [Vendor Defined Widget] wcaps 0xf0051b: Stereo Amp-In
    Amp-In caps: ofs=0x00, nsteps=0x23, stepsize=0x03, mute=1
    Amp-In vals:
    Power states: D0 D1 D2 D3
    Power: setting=D0, actual=D0
    Connection: 0
    Node 0x08 [Audio Input] wcaps 0x10051b: Stereo Amp-In
    Amp-In caps: ofs=0x00, nsteps=0x23, stepsize=0x03, mute=1
    Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
    Converter: stream=0, channel=0
    SDI-Select: 0
    PCM:
    rates [0x160]: 44100 48000 96000
    bits [0x6]: 16 20
    formats [0x1]: PCM
    Power states: D0 D1 D2 D3
    Power: setting=D0, actual=D0
    Connection: 7
    0x18 0x19 0x1a* 0x1b 0x1c 0x14 0x15
    Node 0x09 [Audio Input] wcaps 0x10051b: Stereo Amp-In
    Amp-In caps: ofs=0x00, nsteps=0x23, stepsize=0x03, mute=1
    Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
    Converter: stream=0, channel=0
    SDI-Select: 0
    PCM:
    rates [0x160]: 44100 48000 96000
    bits [0x6]: 16 20
    formats [0x1]: PCM
    Power states: D0 D1 D2 D3
    Power: setting=D0, actual=D0
    Connection: 10
    0x18 0x19 0x1a 0x1b 0x1c* 0x0b 0x14 0x15 0x16 0x17
    Node 0x0a [Audio Input] wcaps 0x100391: Stereo Digital
    Converter: stream=0, channel=0
    SDI-Select: 0
    Digital:
    Digital category: 0x0
    PCM:
    rates [0x160]: 44100 48000 96000
    bits [0x1e]: 16 20 24 32
    formats [0x1]: PCM
    Unsolicited: tag=00, enabled=0
    Connection: 1
    0x1f
    Node 0x0b [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
    Control: name="Beep Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=5, ofs=0
    Control: name="Beep Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=5, ofs=0
    Amp-In caps: ofs=0x23, nsteps=0x41, stepsize=0x03, mute=1
    Amp-In vals: [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0xa3 0xa3] [0x80 0x80] [0x80 0x80]
    Connection: 8
    0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15
    Node 0x0c [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out
    Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
    Amp-In vals: [0x00 0x00] [0x80 0x80]
    Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
    Amp-Out vals: [0x40 0x40]
    Connection: 2
    0x02 0x0b
    Node 0x0d [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out
    Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
    Amp-In vals: [0x00 0x00] [0x80 0x80]
    Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
    Amp-Out vals: [0x40 0x40]
    Connection: 2
    0x03 0x0b
    Node 0x0e [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out
    Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
    Amp-In vals: [0x00 0x00] [0x80 0x80]
    Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
    Amp-Out vals: [0x40 0x40]
    Connection: 2
    0x04 0x0b
    Node 0x0f [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out
    Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
    Amp-In vals: [0x00 0x00] [0x80 0x80]
    Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
    Amp-Out vals: [0x40 0x40]
    Connection: 2
    0x05 0x0b
    Node 0x10 [Audio Selector] wcaps 0x300101: Stereo
    Connection: 4
    0x0c* 0x0d 0x0e 0x0f
    Node 0x11 [Audio Selector] wcaps 0x300101: Stereo
    Connection: 4
    0x0c* 0x0d 0x0e 0x0f
    Node 0x12 [Audio Selector] wcaps 0x300101: Stereo
    Connection: 4
    0x0c* 0x0d 0x0e 0x0f
    Node 0x13 [Audio Selector] wcaps 0x300101: Stereo
    Connection: 4
    0x0c* 0x0d 0x0e 0x0f
    Node 0x14 [Pin Complex] wcaps 0x40018d: Stereo Amp-Out
    Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
    Amp-Out vals: [0x80 0x80]
    Pincap 0x0000003f: IN OUT HP Detect Trigger ImpSense
    Pin Default 0x00000000: [Jack] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0x0, Sequence = 0x0
    Pin-ctls: 0x40: OUT
    Unsolicited: tag=00, enabled=0
    Connection: 1
    0x0c
    Node 0x15 [Pin Complex] wcaps 0x40018d: Stereo Amp-Out
    Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
    Amp-Out vals: [0x80 0x80]
    Pincap 0x0000003f: IN OUT HP Detect Trigger ImpSense
    Pin Default 0x00000000: [Jack] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0x0, Sequence = 0x0
    Pin-ctls: 0x40: OUT
    Unsolicited: tag=00, enabled=0
    Connection: 1
    0x0d
    Node 0x16 [Pin Complex] wcaps 0x40018d: Stereo Amp-Out
    Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
    Amp-Out vals: [0x80 0x80]
    Pincap 0x0000003f: IN OUT HP Detect Trigger ImpSense
    Pin Default 0x00000000: [Jack] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0x0, Sequence = 0x0
    Pin-ctls: 0x40: OUT
    Unsolicited: tag=00, enabled=0
    Connection: 1
    0x0e
    Node 0x17 [Pin Complex] wcaps 0x40018d: Stereo Amp-Out
    Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
    Amp-Out vals: [0x80 0x80]
    Pincap 0x0000003f: IN OUT HP Detect Trigger ImpSense
    Pin Default 0x00000000: [Jack] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0x0, Sequence = 0x0
    Pin-ctls: 0x40: OUT
    Unsolicited: tag=00, enabled=0
    Connection: 0
    Node 0x18 [Pin Complex] wcaps 0x40018d: Stereo Amp-Out
    Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
    Amp-Out vals: [0x80 0x80]
    Pincap 0x0000133f: IN OUT HP Detect Trigger ImpSense
    Vref caps: HIZ 50 80
    Pin Default 0x00000000: [Jack] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0x0, Sequence = 0x0
    Pin-ctls: 0x20: IN VREF_HIZ
    Unsolicited: tag=00, enabled=0
    Connection: 1
    0x10
    Node 0x19 [Pin Complex] wcaps 0x40018d: Stereo Amp-Out
    Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
    Amp-Out vals: [0x80 0x80]
    Pincap 0x0000133f: IN OUT HP Detect Trigger ImpSense
    Vref caps: HIZ 50 80
    Pin Default 0x00000000: [Jack] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0x0, Sequence = 0x0
    Pin-ctls: 0x20: IN VREF_HIZ
    Unsolicited: tag=00, enabled=0
    Connection: 1
    0x11
    Node 0x1a [Pin Complex] wcaps 0x40018d: Stereo Amp-Out
    Control: name="Line Jack", index=0, device=0
    Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
    Amp-Out vals: [0x80 0x80]
    Pincap 0x0000133f: IN OUT HP Detect Trigger ImpSense
    Vref caps: HIZ 50 80
    Pin Default 0x01810000: [Jack] Line In at Ext Rear
    Conn = 1/8, Color = Unknown
    DefAssociation = 0x0, Sequence = 0x0
    Pin-ctls: 0x20: IN VREF_HIZ
    Unsolicited: tag=01, enabled=1
    Connection: 1
    0x12
    Node 0x1b [Pin Complex] wcaps 0x40018d: Stereo Amp-Out
    Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
    Amp-Out vals: [0x80 0x80]
    Pincap 0x0000133f: IN OUT HP Detect Trigger ImpSense
    Vref caps: HIZ 50 80
    Pin Default 0x00000000: [Jack] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0x0, Sequence = 0x0
    Pin-ctls: 0x20: IN VREF_HIZ
    Unsolicited: tag=00, enabled=0
    Connection: 1
    0x13
    Node 0x1c [Pin Complex] wcaps 0x400001: Stereo
    Pincap 0x00000020: IN
    Pin Default 0x40000000: [N/A] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0x0, Sequence = 0x0
    Pin-ctls: 0x00:
    Node 0x1d [Pin Complex] wcaps 0x400000: Mono
    Pincap 0x00000020: IN
    Pin Default 0x00000000: [Jack] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0x0, Sequence = 0x0
    Pin-ctls: 0x00:
    Node 0x1e [Pin Complex] wcaps 0x400300: Mono Digital
    Pincap 0x00000010: OUT
    Pin Default 0x00000000: [Jack] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0x0, Sequence = 0x0
    Pin-ctls: 0x00:
    Connection: 1
    0x06
    Node 0x1f [Pin Complex] wcaps 0x400200: Mono Digital
    Pincap 0x00000020: IN
    Pin Default 0x00000000: [Jack] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0x0, Sequence = 0x0
    Pin-ctls: 0x00:
    Node 0x20 [Vendor Defined Widget] wcaps 0xf00040: Mono
    Processing caps: benign=0, ncoeff=10
    Node 0x21 [Volume Knob Widget] wcaps 0x600080: Mono
    Volume-Knob: delta=0, steps=64, direct=0, val=0
    Unsolicited: tag=00, enabled=0
    Connection: 0
    Codec: Nvidia GPU 0b HDMI/DP
    Address: 0
    AFG Function Id: 0x1 (unsol 0)
    Vendor Id: 0x10de000b
    Subsystem Id: 0x10de0101
    Revision Id: 0x100200
    No Modem Function Group found
    Default PCM:
    rates [0x0]:
    bits [0x0]:
    formats [0x0]:
    Default Amp-In caps: N/A
    Default Amp-Out caps: N/A
    GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
    Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
    Converter: stream=0, channel=0
    Digital:
    Digital category: 0x0
    PCM:
    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3
    Unsolicited: tag=00, enabled=0
    Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
    Control: name="HDMI/DP,pcm=3 Jack", index=0, device=0
    Control: name="IEC958 Playback Con Mask", index=0, device=0
    Control: name="IEC958 Playback Pro Mask", index=0, device=0
    Control: name="IEC958 Playback Default", index=0, device=0
    Control: name="IEC958 Playback Switch", index=0, device=0
    Control: name="ELD", index=0, device=3
    Pincap 0x09000094: OUT Detect HBR HDMI DP
    Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
    Conn = Digital, Color = Unknown
    DefAssociation = 0x1, Sequence = 0x0
    Pin-ctls: 0x00:
    Unsolicited: tag=01, enabled=1
    Connection: 1
    0x04
    Codec: Nvidia GPU 0b HDMI/DP
    Address: 1
    AFG Function Id: 0x1 (unsol 0)
    Vendor Id: 0x10de000b
    Subsystem Id: 0x10de0101
    Revision Id: 0x100200
    No Modem Function Group found
    Default PCM:
    rates [0x0]:
    bits [0x0]:
    formats [0x0]:
    Default Amp-In caps: N/A
    Default Amp-Out caps: N/A
    GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
    Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
    Converter: stream=0, channel=0
    Digital:
    Digital category: 0x0
    PCM:
    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3
    Unsolicited: tag=00, enabled=0
    Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
    Control: name="HDMI/DP,pcm=7 Jack", index=0, device=0
    Control: name="IEC958 Playback Con Mask", index=1, device=0
    Control: name="IEC958 Playback Pro Mask", index=1, device=0
    Control: name="IEC958 Playback Default", index=1, device=0
    Control: name="IEC958 Playback Switch", index=1, device=0
    Control: name="ELD", index=0, device=7
    Pincap 0x09000094: OUT Detect HBR HDMI DP
    Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
    Conn = Digital, Color = Unknown
    DefAssociation = 0x1, Sequence = 0x0
    Pin-ctls: 0x00:
    Unsolicited: tag=01, enabled=1
    Connection: 1
    0x04
    Codec: Nvidia GPU 0b HDMI/DP
    Address: 2
    AFG Function Id: 0x1 (unsol 0)
    Vendor Id: 0x10de000b
    Subsystem Id: 0x10de0101
    Revision Id: 0x100200
    No Modem Function Group found
    Default PCM:
    rates [0x0]:
    bits [0x0]:
    formats [0x0]:
    Default Amp-In caps: N/A
    Default Amp-Out caps: N/A
    GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
    Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
    Converter: stream=0, channel=0
    Digital:
    Digital category: 0x0
    PCM:
    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3
    Unsolicited: tag=00, enabled=0
    Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
    Control: name="HDMI/DP,pcm=8 Jack", index=0, device=0
    Control: name="IEC958 Playback Con Mask", index=2, device=0
    Control: name="IEC958 Playback Pro Mask", index=2, device=0
    Control: name="IEC958 Playback Default", index=2, device=0
    Control: name="IEC958 Playback Switch", index=2, device=0
    Control: name="ELD", index=0, device=8
    Pincap 0x09000094: OUT Detect HBR HDMI DP
    Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
    Conn = Digital, Color = Unknown
    DefAssociation = 0x1, Sequence = 0x0
    Pin-ctls: 0x00:
    Unsolicited: tag=01, enabled=1
    Connection: 1
    0x04
    Codec: Nvidia GPU 0b HDMI/DP
    Address: 3
    AFG Function Id: 0x1 (unsol 0)
    Vendor Id: 0x10de000b
    Subsystem Id: 0x10de0101
    Revision Id: 0x100200
    No Modem Function Group found
    Default PCM:
    rates [0x0]:
    bits [0x0]:
    formats [0x0]:
    Default Amp-In caps: N/A
    Default Amp-Out caps: N/A
    GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
    Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
    Converter: stream=0, channel=0
    Digital:
    Digital category: 0x0
    PCM:
    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3
    Unsolicited: tag=00, enabled=0
    Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
    Control: name="HDMI/DP,pcm=9 Jack", index=0, device=0
    Control: name="IEC958 Playback Con Mask", index=3, device=0
    Control: name="IEC958 Playback Pro Mask", index=3, device=0
    Control: name="IEC958 Playback Default", index=3, device=0
    Control: name="IEC958 Playback Switch", index=3, device=0
    Control: name="ELD", index=0, device=9
    Pincap 0x09000094: OUT Detect HBR HDMI DP
    Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
    Conn = Digital, Color = Unknown
    DefAssociation = 0x1, Sequence = 0x0
    Pin-ctls: 0x00:
    Unsolicited: tag=01, enabled=1
    Connection: 1
    0x04
    --endcollapse--
    !!ALSA Device nodes
    crw-rw----+ 1 root audio 116, 3 Jul 17 17:07 /dev/snd/controlC0
    crw-rw----+ 1 root audio 116, 12 Jul 17 17:07 /dev/snd/controlC1
    crw-rw----+ 1 root audio 116, 2 Jul 17 17:07 /dev/snd/hwC0D2
    crw-rw----+ 1 root audio 116, 11 Jul 17 17:07 /dev/snd/hwC1D0
    crw-rw----+ 1 root audio 116, 10 Jul 17 17:07 /dev/snd/hwC1D1
    crw-rw----+ 1 root audio 116, 9 Jul 17 17:07 /dev/snd/hwC1D2
    crw-rw----+ 1 root audio 116, 8 Jul 17 17:07 /dev/snd/hwC1D3
    crw-rw----+ 1 root audio 116, 7 Jul 17 17:07 /dev/snd/pcmC1D3p
    crw-rw----+ 1 root audio 116, 6 Jul 17 17:07 /dev/snd/pcmC1D7p
    crw-rw----+ 1 root audio 116, 5 Jul 17 17:07 /dev/snd/pcmC1D8p
    crw-rw----+ 1 root audio 116, 4 Jul 17 17:07 /dev/snd/pcmC1D9p
    crw-rw---- 1 root audio 116, 1 Jul 17 17:07 /dev/snd/seq
    crw-rw----+ 1 root audio 116, 33 Jul 17 17:07 /dev/snd/timer
    /dev/snd/by-path:
    total 0
    drwxr-xr-x 2 root root 80 Jul 17 17:07 .
    drwxr-xr-x 3 root root 320 Jul 17 17:07 ..
    lrwxrwxrwx 1 root root 12 Jul 17 17:07 pci-0000:00:1b.0 -> ../controlC0
    lrwxrwxrwx 1 root root 12 Jul 17 17:07 pci-0000:01:00.1 -> ../controlC1
    !!Aplay/Arecord output
    APLAY
    **** List of PLAYBACK Hardware Devices ****
    card 1: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0]
    Subdevices: 1/1
    Subdevice #0: subdevice #0
    card 1: NVidia [HDA NVidia], device 7: HDMI 0 [HDMI 0]
    Subdevices: 1/1
    Subdevice #0: subdevice #0
    card 1: NVidia [HDA NVidia], device 8: HDMI 0 [HDMI 0]
    Subdevices: 1/1
    Subdevice #0: subdevice #0
    card 1: NVidia [HDA NVidia], device 9: HDMI 0 [HDMI 0]
    Subdevices: 1/1
    Subdevice #0: subdevice #0
    ARECORD
    **** List of CAPTURE Hardware Devices ****
    !!Amixer output
    !!-------Mixer controls for card 0 [Intel]
    Card hw:0 'Intel'/'HDA Intel at 0x53300000 irq 46'
    Mixer name : 'Realtek ALC880'
    Components : 'HDA:10ec0880,08600000,00090000'
    Controls : 4
    Simple ctrls : 2
    Simple mixer control 'PCM',0
    Capabilities: pvolume penum
    Playback channels: Front Left - Front Right
    Limits: Playback 0 - 255
    Mono:
    Front Left: Playback 255 [100%] [0.00dB]
    Front Right: Playback 255 [100%] [0.00dB]
    Simple mixer control 'Beep',0
    Capabilities: pvolume pswitch penum
    Playback channels: Front Left - Front Right
    Limits: Playback 0 - 65
    Mono:
    Front Left: Playback 35 [54%] [0.00dB] [off]
    Front Right: Playback 35 [54%] [0.00dB] [off]
    !!-------Mixer controls for card 1 [NVidia]
    Card hw:1 'NVidia'/'HDA NVidia at 0x53000000 irq 17'
    Mixer name : 'Nvidia GPU 0b HDMI/DP'
    Components : 'HDA:10de000b,10de0101,00100200'
    Controls : 24
    Simple ctrls : 4
    Simple mixer control 'IEC958',0
    Capabilities: pswitch pswitch-joined penum
    Playback channels: Mono
    Mono: Playback [on]
    Simple mixer control 'IEC958',1
    Capabilities: pswitch pswitch-joined penum
    Playback channels: Mono
    Mono: Playback [on]
    Simple mixer control 'IEC958',2
    Capabilities: pswitch pswitch-joined penum
    Playback channels: Mono
    Mono: Playback [on]
    Simple mixer control 'IEC958',3
    Capabilities: pswitch pswitch-joined penum
    Playback channels: Mono
    Mono: Playback [on]
    !!Alsactl output
    --startcollapse--
    state.Intel {
    control.1 {
    iface MIXER
    name 'Beep Playback Volume'
    value.0 35
    value.1 35
    comment {
    access 'read write'
    type INTEGER
    count 2
    range '0 - 65'
    dbmin -3500
    dbmax 3000
    dbvalue.0 0
    dbvalue.1 0
    control.2 {
    iface MIXER
    name 'Beep Playback Switch'
    value.0 false
    value.1 false
    comment {
    access 'read write'
    type BOOLEAN
    count 2
    control.3 {
    iface CARD
    name 'Line Jack'
    value false
    comment {
    access read
    type BOOLEAN
    count 1
    control.4 {
    iface MIXER
    name 'PCM Playback Volume'
    value.0 255
    value.1 255
    comment {
    access 'read write user'
    type INTEGER
    count 2
    range '0 - 255'
    tlv '0000000100000008ffffec1400000014'
    dbmin -5100
    dbmax 0
    dbvalue.0 0
    dbvalue.1 0
    state.NVidia {
    control.1 {
    iface CARD
    name 'HDMI/DP,pcm=3 Jack'
    value false
    comment {
    access read
    type BOOLEAN
    count 1
    control.2 {
    iface MIXER
    name 'IEC958 Playback Con Mask'
    value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
    comment {
    access read
    type IEC958
    count 1
    control.3 {
    iface MIXER
    name 'IEC958 Playback Pro Mask'
    value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
    comment {
    access read
    type IEC958
    count 1
    control.4 {
    iface MIXER
    name 'IEC958 Playback Default'
    value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
    comment {
    access 'read write'
    type IEC958
    count 1
    control.5 {
    iface MIXER
    name 'IEC958 Playback Switch'
    value true
    comment {
    access 'read write'
    type BOOLEAN
    count 1
    control.6 {
    iface PCM
    device 3
    name ELD
    value ''
    comment {
    access read
    type BYTES
    count 0
    control.7 {
    iface CARD
    name 'HDMI/DP,pcm=7 Jack'
    value false
    comment {
    access read
    type BOOLEAN
    count 1
    control.8 {
    iface MIXER
    name 'IEC958 Playback Con Mask'
    index 1
    value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
    comment {
    access read
    type IEC958
    count 1
    control.9 {
    iface MIXER
    name 'IEC958 Playback Pro Mask'
    index 1
    value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
    comment {
    access read
    type IEC958
    count 1
    control.10 {
    iface MIXER
    name 'IEC958 Playback Default'
    index 1
    value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
    comment {
    access 'read write'
    type IEC958
    count 1
    control.11 {
    iface MIXER
    name 'IEC958 Playback Switch'
    index 1
    value true
    comment {
    access 'read write'
    type BOOLEAN
    count 1
    control.12 {
    iface PCM
    device 7
    name ELD
    value ''
    comment {
    access read
    type BYTES
    count 0
    control.13 {
    iface CARD
    name 'HDMI/DP,pcm=8 Jack'
    value false
    comment {
    access read
    type BOOLEAN
    count 1
    control.14 {
    iface MIXER
    name 'IEC958 Playback Con Mask'
    index 2
    value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
    comment {
    access read
    type IEC958
    count 1
    control.15 {
    iface MIXER
    name 'IEC958 Playback Pro Mask'
    index 2
    value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
    comment {
    access read
    type IEC958
    count 1
    control.16 {
    iface MIXER
    name 'IEC958 Playback Default'
    index 2
    value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
    comment {
    access 'read write'
    type IEC958
    count 1
    control.17 {
    iface MIXER
    name 'IEC958 Playback Switch'
    index 2
    value true
    comment {
    access 'read write'
    type BOOLEAN
    count 1
    control.18 {
    iface PCM
    device 8
    name ELD
    value ''
    comment {
    access read
    type BYTES
    count 0
    control.19 {
    iface CARD
    name 'HDMI/DP,pcm=9 Jack'
    value false
    comment {
    access read
    type BOOLEAN
    count 1
    control.20 {
    iface MIXER
    name 'IEC958 Playback Con Mask'
    index 3
    value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
    comment {
    access read
    type IEC958
    count 1
    control.21 {
    iface MIXER
    name 'IEC958 Playback Pro Mask'
    index 3
    value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
    comment {
    access read
    type IEC958
    count 1
    control.22 {
    iface MIXER
    name 'IEC958 Playback Default'
    index 3
    value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
    comment {
    access 'read write'
    type IEC958
    count 1
    control.23 {
    iface MIXER
    name 'IEC958 Playback Switch'
    index 3
    value true
    comment {
    access 'read write'
    type BOOLEAN
    count 1
    control.24 {
    iface PCM
    device 9
    name ELD
    value ''
    comment {
    access read
    type BYTES
    count 0
    --endcollapse--
    !!All Loaded Modules
    Module
    zram
    lm85
    hwmon_vid
    aes_i586
    cryptd
    aes_generic
    act_police
    cls_basic
    cls_flow
    cls_fw
    cls_u32
    sch_tbf
    sch_prio
    sch_htb
    sch_hfsc
    sch_ingress
    sch_sfq
    bridge
    stp
    llc
    xt_statistic
    xt_CT
    xt_LOG
    xt_time
    xt_connlimit
    xt_realm
    xt_addrtype
    iptable_raw
    xt_comment
    xt_recent
    xt_policy
    ipt_ULOG
    ipt_REJECT
    ipt_REDIRECT
    ipt_NETMAP
    ipt_MASQUERADE
    ipt_ECN
    ipt_CLUSTERIP
    ipt_ah
    xt_set
    ip_set
    nf_nat_tftp
    nf_nat_snmp_basic
    nf_conntrack_snmp
    nf_nat_sip
    nf_nat_pptp
    nf_nat_proto_gre
    nf_nat_irc
    nf_nat_h323
    nf_nat_ftp
    nf_nat_amanda
    ts_kmp
    nf_conntrack_amanda
    nf_conntrack_sane
    nf_conntrack_tftp
    nf_conntrack_sip
    nf_conntrack_proto_udplite
    nf_conntrack_proto_sctp
    nf_conntrack_pptp
    nf_conntrack_proto_gre
    nf_conntrack_netlink
    nf_conntrack_netbios_ns
    nf_conntrack_broadcast
    nf_conntrack_irc
    nf_conntrack_h323
    nf_conntrack_ftp
    xt_TPROXY
    nf_defrag_ipv6
    nf_tproxy_core
    ip6_tables
    xt_tcpmss
    xt_pkttype
    xt_physdev
    xt_owner
    xt_NFQUEUE
    xt_NFLOG
    nfnetlink_log
    xt_multiport
    xt_mark
    xt_mac
    xt_limit
    xt_length
    xt_iprange
    xt_helper
    xt_hashlimit
    xt_DSCP
    xt_dscp
    xt_dccp
    xt_conntrack
    xt_connmark
    xt_CLASSIFY
    xt_AUDIT
    xt_state
    iptable_nat
    nf_nat
    nf_conntrack_ipv4
    nf_defrag_ipv4
    nf_conntrack
    iptable_mangle
    nfnetlink
    xt_tcpudp
    iptable_filter
    ip_tables
    x_tables
    arc4
    fuse
    nvidia
    snd_hda_codec_hdmi
    ppdev
    ath9k_htc
    ath9k_common
    microcode
    ath9k_hw
    ath
    serio_raw
    psmouse
    evdev
    mac80211
    ums_cypress
    cfg80211
    compat
    usb_storage
    rfkill
    i2c_i801
    uas
    rc_ati_x10
    iTCO_wdt
    firewire_ohci
    ati_remote
    iTCO_vendor_support
    e100
    firewire_core
    mii
    rc_core
    crc_itu_t
    snd_hda_codec_realtek
    parport_pc
    parport
    snd_hda_intel
    snd_hda_codec
    snd_pcm
    snd_page_alloc
    snd_hwdep
    snd_timer
    nfsd
    exportfs
    intel_agp
    intel_gtt
    snd
    nfs
    i2c_core
    agpgart
    nfs_acl
    lockd
    soundcore
    auth_rpcgss
    button
    processor
    sunrpc
    fscache
    autofs4
    ext4
    crc16
    jbd2
    mbcache
    usbhid
    hid
    sr_mod
    cdrom
    pata_acpi
    ata_generic
    uhci_hcd
    ata_piix
    ehci_hcd
    usbcore
    usb_common
    sd_mod
    ahci
    libahci
    libata
    scsi_mod
    !!Sysfs Files
    /sys/class/sound/hwC0D2/init_pin_configs:
    0x14 0x00000000
    0x15 0x00000000
    0x16 0x00000000
    0x17 0x00000000
    0x18 0x00000000
    0x19 0x00000000
    0x1a 0x01810000
    0x1b 0x00000000
    0x1c 0x40000000
    0x1d 0x00000000
    0x1e 0x00000000
    0x1f 0x00000000
    /sys/class/sound/hwC0D2/driver_pin_configs:
    /sys/class/sound/hwC0D2/user_pin_configs:
    /sys/class/sound/hwC0D2/init_verbs:
    /sys/class/sound/hwC1D0/init_pin_configs:
    0x05 0x18560010
    /sys/class/sound/hwC1D0/driver_pin_configs:
    /sys/class/sound/hwC1D0/user_pin_configs:
    /sys/class/sound/hwC1D0/init_verbs:
    /sys/class/sound/hwC1D1/init_pin_configs:
    0x05 0x18560010
    /sys/class/sound/hwC1D1/driver_pin_configs:
    /sys/class/sound/hwC1D1/user_pin_configs:
    /sys/class/sound/hwC1D1/init_verbs:
    /sys/class/sound/hwC1D2/init_pin_configs:
    0x05 0x18560010
    /sys/class/sound/hwC1D2/driver_pin_configs:
    /sys/class/sound/hwC1D2/user_pin_configs:
    /sys/class/sound/hwC1D2/init_verbs:
    /sys/class/sound/hwC1D3/init_pin_configs:
    0x05 0x18560010
    /sys/class/sound/hwC1D3/driver_pin_configs:
    /sys/class/sound/hwC1D3/user_pin_configs:
    /sys/class/sound/hwC1D3/init_verbs:
    !!ALSA/HDA dmesg
    [ 3.398568] Installing knfsd (copyright (C) 1996 [email protected]).
    [ 3.431145] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
    [ 3.462799] parport_pc 00:07: reported by Plug and Play ACPI
    [ 3.462832] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
    [ 3.467010] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input4
    [ 3.468096] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
    [ 3.471112] hda_intel: Disabling MSI
    [ 3.522125] intel_rng: Firmware space is locked read-only. If you can't or
    [ 4.173059] ath9k_htc 1-2:1.0: ath9k_htc: HTC initialized with 45 credits
    [ 4.263632] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input8
    [ 4.263914] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input9
    [ 4.264134] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input10
    [ 4.264423] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input11
    [ 4.267027] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
    I'll also see what kind of help I can get from the developers upstream.

  • I am getting no signal to my dj mixer using m-audio firewire audiophile sound card connected to my mac book pro using Traktor Dj software can anyone help?

    I am getting no signal to my dj mixer using m-audio firewire audiophile sound card connected to my mac book pro using Traktor Dj software can anyone help?
    The firewire port reads the dj software and I can hear music playing through the sound card when I plug my headphones into it but there is no signal to the hardware (my dj mixer).
    I have reset the firewire by turning off my mac book pro for a few hours and can see the sound card device in the fire wire section after clicking on the apple icon on the top left corner of my mac.
    My dj mixer works on another mac computer with the same soundcard and different firewire cable.
    Hope someone can help
    Thanks
    Wayne

    kmiddlet88,
    yes, it could be due to nearly anything listed in your kernel extensions, startup items, launch daemons, launch agents, or user items above. Please check all of your installed third-party software to make sure that the versions which are installed on your MacBook Pro are compatible with Mavericks; uninstall every software package which isn’t Mavericks-compatible. After you’ve done that, boot into Safe mode, and see if you still get the beach ball of doom there. If it doesn’t appear there, restart normally and see if it appears then.

  • Mac Pro with no airport card installed

    I have a Mac Pro with no airport card installed....Can I just purchase an Airport express and connect by ethernet to the Mac pro.... I use Air port Extreme as my router for other computers

    Yes, this is referred to as a ProxySTA in the business.
    HOWEVER, this only became available with the 802.11n Express. I haven't yet seen it OFFICIAL if the new second generation still supports ProxySTA. I'm a bit hesitant to say yes, because the new express leans a little closer to the Extremes which work quite differently.  (haven't had time to test this yet myself)
    I'm curious, why you don't just run an ethernet from your extreme to your Pro... I'm guessing because of the distance?

  • How do I activate a used iPhone 3 with no SIM card for use as an ipod touch?

    How do I activate a used iPhone 3G with no SIM card for use like an iPod Touch? It was apparently on AT&T previously and I have another iPhone 3 that is active on AT&T if that is helpful. Thanks!

    Copied from the link provided.
    Follow these steps to use your iPhone without a wireless service plan:
    Insert the SIM card from your new, activated iPhone or one that was previously used to activate the original iPhone.
    Connect the iPhone to iTunes on a computer connected to the Internet.
    Once iTunes activates the device, you're free to use the iPhone as if it were an iPod touch.

  • I am using iPhone 4s with no sim card. My WiFi turned grey and isn't working. I've tried many methods like freezing and Resetting the network settings, still not working. Now what should I do? (iOS 7.1.2)

    I am using iPhone 4s with no sim card. My WiFi turned grey and isn't working. I've tried many methods like freezing and Resetting the network settings, still not working. Now what should I do? (iOS 7.1.2)

    Put in a micro SIM (SIM need not be active) and
    Restore from backup
    Restore as new
    http://support.apple.com/en-us/HT201252

  • Front audio with PCI sound card?

    Well, the front audio on my Antec P160W worked perfectly with the integrated sound, but I changed to my SoundBlaster Audigy Player because of the HORRIBLE audio quality. Now the front audio ports don't work. What do I need to do to make it work again? I'm not going back to the integrated.
    At first I thought that I had to put the connectors for the front audio on the sound card, but the manual of it doesn't show any of those features.

    I was wondering that myself. The only thing I think you could possibly do is have both the onboard and the pci sound card enabled and use the onboard sound just for the headphones. I have no tried this yet as I do have the cables connected to the mobo but I have the onboard sound disabled.

  • How do I partition a disc with a raid card installed for fcp x and motion

    Hi,
    I have just downloaded fcp x and purchased motion but have found out the drivers for my AJA io HD are not available as yet so decided to revert to FCP 6.5. My system now runs like a dog and then I discovered FCP x and Motion should be installed on a separete partition. I have a Raid card installed on my mac and the application disc disk does not enough space so do not know what I should do. Any help would be welcome.
    Noel

    Hi Mark spencer4,
    The issues I have is No drivers for Aja ioHD so I cant test FCP X to see how it works. When I return to my FCP version 6 it just does not run like it used to and keeps hanging the Aja ioHD so I have to keep refreshing. My motion projects on the FCP timeline now do not open in the old version of motion so I cant round robin as before. My main disc does not have enough space to run FCP X projects and a post on Apple forum said to run FCP X and Motion on a new partition if  you still need to use FCP 6. As I have a Raid card with enough space, If I created a partition on it for fcp X and Motion 5 would FCP 6 work properly again.
    I could not see how to create a partition on the Raid drive?

  • Can i use ipad mini with european sim card

    is ipad mini unlocked? Can i use it with european sim card?

    at least non of the other ipads been sim locked so I'd guess not

  • Using FIOS TV with internal tuner card in a PC?

    I've checked the FAQs and many of the postings but haven't seen anything about this, which makes me wonder if I am looking in the wrong place :-)
    Is it possible to view FIOS TV using an internal computer TV Tuner card, and using Windows Media Center to view programs?
    I do not have any premium channels, like HBO, etc.  I have not purchased a tuner card yet, (pending the answers I get here), but what I have seen online for various types of internal computer tuner cards mentions Digital ATSC, Digital QAM, etc.  It seems to indicate I can connect the cable directly to the TV card if the channels are not encrypted, and therefore I would not need a set top box.
    My question is, can I connect the cable directly to the tuner card, without a set top box, or must I have a set top box in all circumstances?  Can I see anything without the set top box?

    Unless the tuner card has provisions for a cable card (would be rented from Verizon for $3.99 / month) all channels with the excption of the broadcast (OTA) and PEG channels are encrypted.  That means no ESPN, USA, SyFy, etc. - only the broadcast networks, andy local independents, and any carried Public Broadcasting stations. 
    Actually has been discussed many times - did you try the forum search feature?
    If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem.

  • HTC One M7 ... How to use in FRANCE with french Sim Card ?

    Hello,
    I'm french and I was in US for few month ... I bought and used an HTC One M7 Verizon with a prepaid card and everything was OK.
    Now i'm back to FRANCE and i would like to use it with a French SIM Card.
    The sim card is detected by the phone but the thing is that only work on Edge ... no 3G or 4G ... so i can call or received call with Edge but no way to go on internet as i don't have 3G.
    The french sim card is 3G-4G ready ... is there something i can do on the phone configuration to have 3G/4G
    Thanks a lot for your help

        Hello zorin!
    I can understand your desire to use the phone you recently purchased on the network in France! All of our 4G LTE phones are automatically unlocked for international use. However, they are designed primarily for use on the Verizon network, and it is possible that they will not work to their top performance capabilities on another network.
    You can reach out to HTC to find out if there are any other options for getting your device to work bettery in France. HTC can be reached at 866-449-8358.
    Thank you,
    MichelleH_VZW
    Follow us on Twitter @VZWSupport

  • Pavilion p6-2117 won't get past the splash screen with a parallel card installed.

    Pavilion p6-2117c won't get past the splash screen with a pci express parallel card installed.  I take the card out and the machine works just fine.  The screen says press "esc" for startup menu but nothing happens.
    This question was solved.
    View Solution.

    Take a careful look at the slot and see if any of the pins are broken or smashed to the bottom of the slot.  Do you have another pci slot to try or just the one?
    Reminder: Please select the "Accept as Solution" button on the post that best answers your question. Also, you may click on the white star in the "Kudos" button for any helpful post to give that person a quick thanks. These feedback tools help keep our community active, so you receive better answers faster.

  • Powerbook will not startup with airport extreme card installed

    I have a 2 year old powerbook using 10.3.9 an djust of late when my airport card is in, The computer just sends me to the open Firmware right after i turn it on.when i type mac-boot it comes up with a broken folder icon. however when i take my card out i dont have a problem. is there a wa i can ues my computer and the airport at the same time? what do you think i should do.

    it is a 867 mhz g4 with 256 mb ddr ram. 40 gb hd and
    a combo drive. i hope that is helpfull.
    This PowerBook requires the original Airport card, you can not use the Airport Extreme card in that PowerBook, any attempt to do so could result in damage to both the card and the PowerBook.
    Either change the AE card for an original Airport or use a third party 802.11g card in the cardbus slot.
    iFelix

  • Computer won't boot with PCI-GPIB card installed

    I'm running a windows XP system with Labview 7.1 installed. I have installed the GPIB drivers, but when I insert my PCI-GPIB card, the computer will not boot(it freezes before the POST). I'm running a Shuttle "MK40VN" KM400 Chipset Motherboard.

    Well, nevermind, I just verified that the card is in fact fried.

  • Bios freezes on Hp IPISB-CH2 with new graphic card installed

    I own HP Pavilion Elite HPE H8 1010cs. Motherboard is HP IPISB-CH2. I bought new graphic card GAINWARD Nvidia GeForce GTX 970 4GB together with 600W PSU Corsair CX600M. First I tried my new PSU with my old GPU nvidia 550Ti. It worked perfectly. But when I replaced old card with new GTX 970, bios freezes on the first power on window. Escape does not work. Should I return new graphic card, or is there still some hope in this?
    This question was solved.
    View Solution.

    Hello @Tomas83,
    I understand that you are having issues getting your HP Pavilion HPE h8-1010cs Desktop PC towork with your Gainward GeForce® GTX 970 Phantom 4GB Graphics Card. I believe the reason you are experiencing this issue is the the break in the downward compatibility on the PCIe slots was broken at around the Gen 2.1 mark and you are trying to put a Gen 3.0 card in a Gen 1.0 slot. This in essence makes your computer incompatible with the graphics card you have chosen to use.  I am providing you an article on the overclock.net website titled The final answer to the controversial PCIe x16 version compatibility., where the author explains what I described and goes into how he made the determination. I would advise you review the article if you have any questions concerning the issue you are facing.
    I hope I have answered your question to your satisfaction. Thank you for posting on the HP Forums. Have a great day!
    Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
    Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
    Dunidar
    I work on behalf of HP
    Find out a bit more about me by checking out my profile!
    "Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Maybe you are looking for

  • Material Mandatory not showing at sales order level error

    Hi Every one, According to my client Requirement  at the time of  sale order creation material is mandatory , but i tried through Incompletion log its showing material mandatory but the problem is after entered the material in one line item when i tr

  • IPod not syncing with iTunes

    Okay, I checked the other topics here but I don't see anything that quite matches my issue. I recently (like many others) updated to iTunes 9 (I'm using Windows Vista), and now my 5th Gen 30gb video iPod won't sync. I'm not getting any error messages

  • IDVD 7.04 on Mac Mini (Late 2009) Connected HDMI to 46 Toshiba LCD

    I suspect that there is a video setting that is wrong, but has anyone been able to get iDVD to not crash with the hardware connection in the subject? iDVD keeps crashing right when I am ready to add videos to my project.

  • Cannot SELECT into a user-defined type variable

    Hi All, Oracle 11.2 on Linux. See the steps below. I am not able to insert/select into a TYPE variable. I do not want to do a TABLE declaration in my PL/SQL block, but want to use a user defined type. Is it possible ? SQL> create or replace type samp

  • What is badi and where used?

    Tell me about badi and its uses in abap? Thanks.