Using routers as wireless access point

Hello,
i am thinking of buying Linksys x2000 , WAG160N or any other you suggest to use as a wireless access point. Is it possible?
My setup is : I get my internet from my neighbor by ethernet cable from his router. My house is two-storied and ethernet cable comes to top left corner of first floor and the devices(two notebook) are on the bottom right corner at the second floor , insulation greatly reduces the signal strength.
Thank you.

You can use any other routers, do not use X2000 or WAG models. I think they get Internet from an RJ11 connection. Use an Access Point. WAP series.

Similar Messages

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network.

Can I use iMac as wireless access point?

My network equipment: ADSL modem (which has no integrated wireless) with Buffalo AirStation (802.11b) wireless access point
I have had a reasonably stable broadband situation for a long time (hence the ancient equipment!) and have been able to access the internet via my ADSL modem/ethernet router using ethernet wires from my iMac G5, and two desktop PCs running Linux and Windows. I have also been able to access via the wireless Buffalo Airstation on various laptops over the years. My wife's brand new MacBook has been connecting wirelessly for a couple of weeks.
Until last night...
Then the AirPort signal dropped to zero and a neighbour's network was suggested as the network I need. I looked at the Buffalo Airstation and there was a flashing red light (and flashing green ones as well). Being an experienced chap I turned it off and turned it back on! For about five minutes the Airport signal was back. Then it disappeared with flashing lights as before. Repeated a few times with no change...
I don't know if the problem is related to the neighbour's wireless signal or not but I decided that it could be the AirStation getting flaky so I tried creating a network on the iMac with a view to sharing its wired connection.
I can log on to this iMac network from the MacBook and I have changed the Systems Preferences to share the connection on the iMac but the MacBook says it is not connected to the internet. Anyone got any ideas what I might be doing wrong? Should I be entering the ADSL modem router in the internet connection details (which is what I have done) or should I be entering something else?
Is what I am trying to do even possible? I haven't found any exact parallels in the documentation or the forums...
Any help greatly appreciated!

Does the Buffalo AirStation allow you to change the channel being used?
You can share an Internet connection over Ethernet to other computers using Airport. You set it up in System Preferences Sharing pane Internet tab (if using Tiger). On the MacBook, you should just use the default +Configure Using DHCP+ setting. Be sure you clicked to Start the sharing on the iMac. On the MacBook, be sure you select the wireless network that is the iMac's name.

Using Mac as Wireless Access point

If i set up the MAC to be a Wireless Access point, via the Sharing option in System Preferences, it works fine if i am trying to connect a PC, other MAC or iPhone to the internet, but devices such as Nintendo DS or Kindle fail (these devices work OK on other wireless networks) to connect they recognise the Wireless network OK but fail to connect and i have tried the basic configuration with no security and it still fails.
What am i doing wrong please?
Thx
John

I managed to resolve this issue with help from the following:-
http://hints.macworld.com/article.php?story=20051119155606277
Thanks

Using router as wireless access point

I have connected two routers to my BT broadband Hub (via ethernet) in order to create one big Wirless LAN across the house. Unfortunately, the routers have simply created independent wireless lans which I need to log into separately as I move around the house. Any idea how I edit the routers so that they all use the same user ID and Password....and effectively act as one integrated wireless network, so that i can connect to them as I move between them seamlessly. Thanks.....

The Apple Support Communities are an international user to user technical support forum. As a man from Mexico, Spanish is my native tongue. I do not speak English very well, however, I do write in English with the aid of the Mac OS X spelling and grammar checks. I also live in a culture perhaps very very different from your own. When offering advice in the ASC, my comments are not meant to be anything more than helpful and certainly not to be taken as insults.
http://www.ehow.com/how_8554130_use-wifi-routers-same-lan.html

Inconsistent DHCP leases while using WRVS4400N as Wireless Access Point

I have a small home network that is made up of a Windows 2003 server connected directly to my WRVS4400N. The DHCP server is disable in the WRVS4400N and all DHCP and DNS services are being provided by the 2003 server. My WPSM54G print server has no problem obtaining an IP address but my other 3 non-Linksys wireless computers are timing out during the IP request process. All 3 computers have a good wireless connection and will work fine if I configure them for a static IP address but I would rather use DHCP if at all possible. Do you have any information that could help me clear up this problem. I have installed the latest firmware which is version 1.01.03 but this has not helped the situation.

have you tried to direct connect your PCs to the router just like your server and check if it can obtain and IP?
try changing wireless settings from the router [SSID and CHANNEL]
enable WPA as well
are they able to obtain an IP from a diff wireless network?

WRT310N as a "Wireless Access Point"

Hello,
I am in the market for a wireless device to add to an existing subnet. I see many tutorials regarding routers as wireless access points, but I am not sure if this device will work.
My plan is to connect one of the switch ports to an existing switch and not use/configure the WAN port.
I would rather purchase a router then a true WAP do to the fact that it can also act as a router (should I need it later), whereas a WAP cannot.
Any thoughts on this is appreciated.

Well try upgrading the firmware of the router & keep on holding tightly
the reset button in such a way that power light is blinking on the
router & then do a complete network power cycle i.e., unplug the power
cables from the modem & from the router & then plug in the power cable
to the modem first once all the lights are solid green you could plug
in the power cable to the router & check out it will definately work!!
Open the setup page of router using 192.168.1.1 then put in the
password as admin...all you need to do is do the wireless settings such
as Radio Band Frequency to Standard 20 MHZ frequency,channel to 11.
Also,the advanced wireless settings to Beacon Interval=50,Frag
thres=2306 & Rts thres=2307 & then uncheck a Block Anonymous Internet
Requests & it will definately work!!!

Can I disable my Verizon Fios Router Wireless radio, connect it to a switch and use my airport express as my wireless access point connected to an in wall ethernet port?

Here's the deal. I have a Verizon Fios MI424WR router. My house has CAT5 throughout the house. The media panel is located in the garage. I want to take the Verizon Fios Router and cannot it in the media panel so I can connect a switch to it, that way, all my CAT5 can fire throughout the house. Verizon being Verizon decided to connect the router directly in the office.
Can I go this route (Router in media panel, switch cross connect to it) and use Airport Express, connected to one of the in-wall CAT5 ports in my house and then set it up as my wireless access point to provide wifi to my portable devices (iPad, iPhone, Macbook)? Is this possible? Will Airport Express comminicate with my verizon router via ethernet in-wall? Do I have to turn off the wireless radio in the Verizon router? Any help would be greatly appreciated!

That is right, by hard wired I was just making clear wired vs wireless attachment. AirPort family of devices will only act in a repeater mode with their own family members, not FiOS routers. they have to be wired to work.
There are some useful docs you can download from Apple, Support, Manuals, Peripherals, AirPort (just follow thos links from the Support button on the top bar):
Apple AirPort Networks
Designing AirPort Networks
AirPort Express Setup Guide
The last has a diagram of what you are trying to do, though without the house wiring, etc., but the basic principle.

Using WRT160N as a wireless access point from TP-WR941N

Hi,
I have a TP-WR941N router connected to the internet. I recently bought a WRT160n in the hope that I will be able to use it as an access point to extend the wireless range.
Essentially, I have the router and modem in one apartment, but need to be able to access the internet from another. The setup would look something like this:
|||===Apartment 2======================|||========= Apartment 1 ==================|||
||| [Computer] ))))) ((((( [TP-WR941N] ))))) ||| ((((( [WRT160n] ))))) ((((( [Computer] |||
||| [Modem]----------------------+ | ||| |||
||| [Computer]-----------------------+ ||| |||
|||==================================|||======================================|||
Is this possible? Do I need to use custom firmware or will the WRT160n work with the supplied firmware? What would I need to set up?

WRT160N router can not communicate with another router on a wireless connection.
You will need to run cable between both the routers.
I think you can try third party firmware.

Using the Aiport Express as a Wireless Access Point on Windows XP

I would like to use my airport express as a wireless access point so that it will connect wirelessly to my router and via an Ethernet cable to my laptop that does not have a wireless card. Also, I have a laptop that I don't have admin rights to, so I can't install the airport express software. I do have another computer in which I am able to set things up on, but ultimately I would like to use the Ethernet port on the airport express as a DHCP device that once configured it will automatically connect to my laptop even after powering off and on any machine with DHCP. I believe that this can be done - but correct me if I am wrong.
So far, I have been able to get the airport express to connect to my router, but I can't seem to get the intenet connection on my laptop. Can someone help? Does the software have to be installed to work even after it is configured?
Thanks!

I have successfully gotten my AX to connect to my wireless router via the wireless client mode, but I can't seem to get the network connection to come out the either net jack of the AX.
Unfortunately, the wireless client mode will not activate the Ethernet port. The purpose of this mode is to connect to an existing wireless network as a client (just like any other device connecting to the network) and be able to either/or stream iTunes or share a USB printer.
The only mode where the Ethernet port is enabled, would be to configure the AX as either a relay or remote base station in a Wireless Distribution System (WDS). But, unfortunately, your Belkin wireless router may not be WDS-compatible with the AirPorts.
Again, the only Belkin routers, that I'm aware of that are compatible are the F5D7230-4 & F5D7130.

Use WRT110 as a wireless access point to connect desktop computer to a WRT160N network.

I am having a problem setting my WRT110 connected to a desktop computer, as an access point to a net broadcast by a WRT160N. The WRT connects to the desktop computer, but does not see the WRT169N network. A laptop with 802.11g sitting next to the desktop is able to link to the WRT160N network, although the signal is weak, but workable. Has anyone any ideas on how to use the WRT110 as as access point rather than a router. I spoke with CISCO technician level 2, and he says it can't be done. CISCO website for WRT110 describes it as three devices in one, one being a wireless access point. CISCO technician says get a WAP, but I think I should be able to use the WRT110. Help appreciated.

Linksys Wireless Routers (WRT...) are simple access points. They don't establish a connection to any other wireless device. They only allow wireless access for clients. That's the definition for an access point: to be a point of access into the LAN for clients. It is a common misconception that a "wireless access point" would always include bridging or repeating capabilities although that is a completely different mode of operation.
What you want is not an access point but a wireless repeater (WRE) or a wireless bridge (WET) or a combination. The Linksys WAPs are versatile wireless devices which can be operated as access point, repeater, and bridge.
Message Edited by gv on 09-11-2008 09:52 AM

Using WRT54GR as a Wireless Access Point only

I have a WRT610N as my main router. I want to use an existing WRT54GR purely as a wireless access point and ethernet switch. Any suggestions on how best to do that so I can still access the WRT54GR to make configuration changes? Right now I have the network functionality working by simply not using the Internet port on the WRT54G but by going to 192.168.1.1 I can only get to the WRT610N.

(Restarting this thread).
I made the change you suggested and statically assigned 192.168.1.200 to the WRT54GR. I can reliably access it through this IP address. I connected it to the rest of my network by using one of the 4 switch ports (not the Internet port). I disabled DHCP on it and configured the Wireless settings to be the same (same SSID and Security Settings) as my other wireless router.
What I'm finding is that devices in my house won't assoicate with it. I tried changing the SSID to a different value; devices were able to see the new SSID but when I entered the pasword they told me that no DHCP server could be detected. A wired device that I plugged into another of the 4 switch ports on the WRT54GR was able to pick up an IP address from the main router just fine so I know that basic connectivity is OK.
To achieve what I want (i.e. the WRT54GR just acts as a wireless base station to extend wireless coverage in the house), do I need to connect the WRT54GR to the rest of the network using the Internet port rather than a switch port? If so, what configuration settings do I need to set up so that all the devices can get their IP address from the main router?

Can I use this as a wireless access point for my network

can I use this as a wireless access point for my network

umm... use what?
A Time Capsule? Sure. It's just like many other wireless base stations. It can run in either bridge or route mode - in bridge mode it's just like an access point linking the wired and wireless networks together.

Can I use my Macbook as a wireless access point?

I have an odd question.
I was wondering if it is possible to use my MacBook as a wireless access point. I am traveling to my parents house for Christmas with my Nintendo Wii, and they do not have wireless internet. Here is what I would like to do:
Attach my MacBook to my parents wired internet hub.
Create a wireless network with my MacBook.
Connect to that wireless network on my Wii.
I know this is an odd question, but it seems fairly feasbible in my head, I'm just not sure how to go about doing it.
Any help would be GREATLY appreciated. Thanks!
Macbook Mac OS X (10.4.8)

Actually, it's quite simple... like Robert said, go to System Preferences > Sharing > Internet and choose to share your connection from built in ethernet with computers using AirPort. Click on Airport options and then specify the wireless "network" name you wish to use and whether or not you want security. If you are only playing games with the Wii, I would suggest not enabling security... It would only make things more difficult... plus when sharing the connection like this, you only have the option of using WEP which isn't really that secure anyway in the right hands. Also, when you specify a network name, choose one with no spaces; this will also make things easier for your Wii to connect. That should do it! Good luck!!
Hope this was a help!

Can I use my AirPort as a wireless access point?

Can I use my AirPort as a wireless access point? Can I disable DHCP? How? I have model A1143.

Can I use my AirPort as a wireless access point?
Yes, if it connects to your main router using a permanent, wired Ethernet cable connection. Connect the Ethernet cable from one of the LAN <--> ports on the main router to the WAN (circle of dots) port on the AirPort Extreme.
Can I disable DHCP
Configure the AirPort to operate in Bridge Mode. That will turn off both DHCP and NAT services. If you are using the setup utility on a recent version of the Mac or iPhone/iPad, the utility will automatically set up the AirPort for you in Bridge Mode when it detects another router on the network.
How?
This will depend on what operating system you have your Mac or PC, or whether you want to use an iPhone or iPad for the setup. Let us know on that.
I have model A1143.
This model would be anywhere from 6 to 8 years old depending on when it was originally sold. Please keep in mind that the useful life.....on average.....for a wireless router designed for home use is about 5 years.

Using routers as wireless access point

Similar Messages

Maybe you are looking for