Using StandAlone Hyper V Server 2008 R2 - clustering service not start - with error code 2 when you try to start the service

Dear All,
Kindly help me for the above.
I have tried out the following:
time sync with DC - checked
Re-install the feature and restart the servers
check registry key value winreg - local service account read only and added domain admin account
2 days googling, no luck
Generate cluster report and error error_mod_not_found (126) reported.
Thanks

Hi,
Now that you have a cluster in place and you installed a VM on this but is the VM HA enabled ?
even on a cluster your VM can still be single server. For creating a HA VM you need shared storage or shared VHDX. and you will need the broker services with out this there is no-way the VM will failover.
Check on teched on how to do this or my blog:
http://blogs.msdn.com/b/clustering/
http://robertsmit.wordpress.com/?s=shared+vhdx
http://robertsmit.wordpress.com/2014/01/14/virtual-hard-disk-sharing-shared-vhdx-storage-pool-usage-in-failover-clustering-windows-server-2012-r2/
http://robertsmit.wordpress.com/2013/06/12/windows-server-2012-configure-deploy-hyper-v-replica-broker-how-to-tee13-msteched/
Greetings, Robert Smit Follow me @clustermvp http://robertsmit.wordpress.com/ “Please click "Vote As Helpful" if it is helpful for you and Proposed As Answer” Please remember to click “Mark as Answer” on the post that helps you

Similar Messages

This copy of Microsoft Office 2013 cannot be used on a computer running Terminal Services" error message when you try to open the Click-to-Run version of an Office 2013 program or suite on a terminal server

Hi All,
I have Citrix VDI (Virtual Desktop Infrastructure) Implemented
in my company and installed few Applications on App Server lets say.... MS Office 2013, filzialla, putty, etc...
I assigned these apps to the users through CITRIX STUDIO, when I try to use these apps. on VDI everything is working fine only when i tried to open Word, Excel or Powerpoing, outlook it throws error as
""This copy of Microsoft Office 2013 cannot be used on a computer running Terminal Services" error message when you try to open the Click-to-Run version of an Office 2013 program or suite on
a terminal server"" and apps gets closed.
Please help me on this ASAP.
Thanks & Regards,
Sachin Shinde

Hi,
As mentioned in ths article below, run for Office 365 products on to a Remote Desktop Session Host server is not supported. You can install Office products for Office 365 to a virtual desktop, but the virtual desktop must be assigned to a single user.
http://technet.microsoft.com/en-us/library/jj219423(v=office.15).aspx
Regards,
Melon Chen
TechNet Community Support

HT1414 I used to have 'sky at night' app but it got deleted in error, now when I try to download the app I get 'this app is incompatible with this phone' ' this app requires a gyroscope'...why ? whats changed ? how do I resolve the issue ? thanks CB

I used to have 'sky at night' app but it got deleted in error, now when I try to download the app I get 'this app is incompatible with this phone' ' this app requires a gyroscope'...why ? whats changed ? how do I resolve the issue ? thanks CB

I used to have 'sky at night' app but it got deleted in error, now when I try to download the app I get 'this app is incompatible with this phone' ' this app requires a gyroscope'...why ? whats changed ? how do I resolve the issue ? thanks CB

Server 2008 R2 Standard - Netlogon Service fails to start with error code 31 a device attached to the system is not functioning

Device manager does not show any signs of failed hardware
Server used to be the only domain controller in the network
We had a power failure that resulted in the machine powering off incorrectly (3 months ago or so)
Windows would not start for a missing file
Followed a guide to resolve and we were able to get into windows
Since then the OS has not seemed to work correctly
Server was demoted and AD moved to another server
I am now not able to assign permissions to folders to domain users because this machine does not see the domain
We still use this server as a file server

I believe that your system is facing some corruptions.
The easiest way to proceed would be to migrate the server content to another location, re-install it and migrate them back.
Otherwise, you can try running chkdsk /r /f and sfc /scannow
and see if this helps.
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile

I cant get the itunes store to work , it has a error code when I try to use it, any idea why?

I cannot get the itunes store to work, it has an error code when I try to use it, any ideas?

What error code number are you getting, rodeo?

I recently purchased used macbook pro 15" but unfortunately i erase the harddisk and did not have back up but when i try to reinstall the mac os x lion it ask me the id password,how i can purchse the mac os x lion.

i recently purchased used macbook pro 15" but unfortunately i erase the harddisk and did not have back up but when i try to reinstall the mac os x lion it ask me the id password,how i can purchse the mac os x lion.
where from i can buy the mac os x lion because i am using windows base system when i try to buy from apple web side it show in app store only not in itunes

Have you tried booting from the Recovery HD to reinstall Lion?
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
You will need the Apple ID and password used to purchase Lion. If you have not purchased Lion, then you will need to purchase the Snow Leopard DVD and install Snow Leopard then update it to 10.6.8 to access the App Store where you can purchase and download Lion under your own Apple ID. Or you can purchase the Apple USB Lion installer flash drive at any local Apple retailer or the Online Store.

Since I installed Nero 2104 I get an error message when I try to start iTunes: registry settings changed probably due to other cd/dvd burning program please reinstall iTunes, which I've done using repair option but the problem persists...?

Since I installed Nero 2014 I get an error message when I start iTunes that registry settings for importing and burning cds/dvds have changed probably due to other burning software installed please reinstall iTunes, which I've done using 'repair' option, but the problem persists. I have been able to import cds to iTunes since I installed Nero, but it won't anymore. Does anyone recognize this problem and have a solution? Thanks for any help. Using Windows 7.

I'd start with the following document, with one modification. At step 12 after typing GEARAspiWDM press the Enter/Return key once prior to clicking OK. (Pressing Return adds a carriage return in the field and is important.)
iTunes for Windows: "Registry settings" warning when opening iTunes
If you're still getting the error message (especially when you plug in the Touch), I'd check for a device filter confusion on the PC. (They can affect the connection of USB devices to a PC, as well as burning and importing CDs.) For that one, see:
iTunes for Windows: Troubleshooting CD issues caused by device filters

BUG: An 8144 error occurs when you try to attach a database to an instance of SQL Server by using SQL Server Enterprise

Hi guys...
just wondering if any of you have come up with a 8144
database error... I'm getting this through calling cfstoredproc
with more than 16 params...
if you know the workaround... please please help
thanks

Power Query does not support SQL Server 2000. I believe it will work with SQL Server 2005, but if I remember correctly the earliest "officially supported" version is 2008.
There were a lot of changes to the system catalog tables between 2000 and 2005.

I get an error message when I try to empty the trash in order to clear up an external hard drive. I had been using it for time machine, have shifted that to a larger external hard drive, and want to free up the space for photographs. Any suggestions?

What should I do when I get an error message (error code - 8003) when I'm trying to empty the trash to clear up additional space on an external hard drive?

Yes. And you should not have moved that folder. Put it back. To move your iTunes library move the folder from User's Music.
tt2

Using iPad (6.01), can't run videos requiring Adobe Flash Player (AFP). When I try to download the AFP sw, I receive a msg stating that AFP is not supported by my device, though it is supported by Apple Desktops & mobile devices! Any suggestions?

gghh

There is no Flash Player for iOS devices. Adobe has to make a Flash player for each different computing platform. Just because Flash exists for Mac and Windows computers, does not automatically mean it exists for completely different mobile operating systems.
Adobe ceased development of Flash for all mobile devices way back in November 2011. It has even been removed from Android devices as of August 2012.
Flash on mobile is dead.

Error upgrading Hyper-V Server 2008 R2 to 2012: 0x80070490

Hi everyone!
As it is release day for Hyper-V Server 2012, I decided to go ahead and upgrade from Hyper-V Server 2008 R2. However, I keep getting this error:
"Windows Setup cannot find a location to store temporary installation files. To install Windows, make sure that a partition on your boot disk has at least 1198 megabytes (MB) of free space.
Error code 0x80070490"
I have over 20 gigs free on the boot volume, and tons more on my VHD volume, so I don't know why it's doing this. I have shut down all VMs, there are no snapshots, nothing cluttering up my C: drive, and yes I've rebooted it several times. I have
also tried copying the installation DVD to a local volume and installing that way, but I keep getting the same error. I know the quick solution would be to just format, reinstall clean, and pray that my VMs import into 2012 (which are already safely
on another volume), but there has to be a reason this is happening.
Any ideas? :) Thanks!

Hello Vincent,
I get the same error trying to upgrade my 2008R2 server to 2012. Here's my diskpart output for the partition (it's a mirrored partition):
DISKPART> detail volume
Disk ### Status Size Free Dyn Gpt
Disk 2 Online 298 GB 1024 KB *
Disk 1 Online 298 GB 1024 KB *
Read-only : No
Hidden : No
No Default Drive Letter: No
Shadow Copy : No
Offline : No
BitLocker Encrypted : No
Installable : Yes
Volume Capacity : 297 GB
Volume Free Space : 268 GB
Any suggestions?

"Unauthorized Host" error when you try to connect to the admin server

"Unauthorized Host" error when you try to connect to the admin server

If you see this error message when you try to connect to a Netscape
administration server:
Internal Error
The administration server was unable to fulfill your request.
Reason: Unauthorized host
--------------------------
Here is how to solve the problem and gain access. First you should
temporarily open access to all sites, and then once you make sure that
this lets you get into your administration server, try again to set up
the domain name or IP address access restrictions you want.
For all 2.x/3.x Netscape servers on Windows NT and Unix, or for Commerce and
Communications servers (1.x) on Unix:
<OL>
<LI>Open the "ns-admin.conf" file with a text editor. You can
find this file in the "admserv" directory under your Netscape
server root. The directory is named "admin-serv" in 3.x servers.
<LI>Delete the "Hosts" and "Addresses" lines you see there (either one
of them might not be present). Don't confuse the "Addresses" line,
which you should delete, with the "Address" line, which you should NOT
delete.
<LI>Save the file, then restart your administration server (on Unix run
"stop-admin" then "start-admin"; on Windows NT go into the Services
control panel and stop/start the "Netscape Admin Server" service).
</OL>
For Commerce Server or Communications Server (1.x) on Windows NT:
<OL>
<LI>Go into the registry editor. On Windows NT 4.0, run the command
"regedit". On Windows 3.51, run the command
"regedt32".
<LI>Navigate down to the section
"HKEY_LOCAL_MACHINE\SOFTWARE\Netscape\Administration".
<LI>Delete the "Hosts" and "Addresses" entries you see there (either one
of them might not be present). Don't confuse the "Addresses" entry,
which you should delete, with the "Address" entry, which you should NOT
delete.
<LI>Close the registry editor, then restart your administration server
by going into the Services control panel and stopping then starting the
"Netscape Administration" service.
</OL>
Now try again to access your administration server. Remember, the URL
will be something like "http://servername:12345/", where
"12345" is where the administration server's port number goes.
If you still get the same "Unauthorized host" error, then make sure that
your "ns-admin.conf" file really doesn't contain any "Hosts" or
"Addresses" lines any more, and try stopping your administration server
again then starting it back up.
Once you have access to your administration server, you can try again to
set up the access controls you want.
<UL>
<LI>For the administration server on a 3.x server installation, select
"Admin Preferences" from the General Administration page (the first page
you see when you connect to the admin server), then click on "Superuser Access
Control" and enter hostname and IP address restrictions. If you want
allow access to multiple clients, you'll have to use wildcard patterns
(separate the subsrings with a pipe character, like
"(host1|host2|host3)"); the substrings must be enclosed in parentheses, as shown.
If you're setting up hostname restrictions, you'll need to make sure that
your DNS can resolve those hostnames -- it's generally safer to stick
with IP address restrictions. When you're finished configuring this,
click "OK" then restart your admin server.
<LI>For the administration server on a 2.x server installation, select
"Configure Administration" from the Server Selector page (the first page
you see when you connect to the admin server), then click on "Access
Control" and enter hostname and IP address restrictions. If you want
allow access to multiple clients, you'll have to use wildcard patterns
(separate the subsrings with a pipe character, like
"(host1|host2|host3)"); the substrings must be enclosed in parentheses, as shown.
If you're setting up hostname restrictions, you'll need to make sure that
your DNS can resolve those hostnames -- it's generally safer to stick
with IP address restrictions. When you're finished configuring this,
click "OK" then restart your admin server.
<LI>For the administration server on a 1.x server installation, select
"Configure Administration Server" from the bottom of the Server Manager
page, then enter hostname and IP address restrictions. If you want
allow access to multiple clients, you'll have to use wildcard patterns
(separate the substrings with a pipe character, like
"(host1|host2|host3)"); the substrings must be enclosed in parentheses, as shown.
If you're setting up hostname restrictions, you'll need to make sure that your
DNS can resolve those hostnames -- it's generally safer to stick with IP address
restrictions.
When you're finished configuring this, click "Make These Changes" then
restart your admin server.
</UL>
If you still find yourself getting an "Unauthorized host" error message,
you can use the above steps to open up access and try different
settings.

"Unauthorized Host" error when you try to connect to the admin server

If you see this error message when you try to connect to a Netscape
administration server:
Internal Error
The administration server was unable to fulfill your request.
Reason: Unauthorized host
--------------------------
Here is how to solve the problem and gain access. First you should
temporarily open access to all sites, and then once you make sure that
this lets you get into your administration server, try again to set up
the domain name or IP address access restrictions you want.
For all 2.x/3.x Netscape servers on Windows NT and Unix, or for Commerce and
Communications servers (1.x) on Unix:
<OL>
<LI>Open the "ns-admin.conf" file with a text editor. You can
find this file in the "admserv" directory under your Netscape
server root. The directory is named "admin-serv" in 3.x servers.
<LI>Delete the "Hosts" and "Addresses" lines you see there (either one
of them might not be present). Don't confuse the "Addresses" line,
which you should delete, with the "Address" line, which you should NOT
delete.
<LI>Save the file, then restart your administration server (on Unix run
"stop-admin" then "start-admin"; on Windows NT go into the Services
control panel and stop/start the "Netscape Admin Server" service).
</OL>
For Commerce Server or Communications Server (1.x) on Windows NT:
<OL>
<LI>Go into the registry editor. On Windows NT 4.0, run the command
"regedit". On Windows 3.51, run the command
"regedt32".
<LI>Navigate down to the section
"HKEY_LOCAL_MACHINE\SOFTWARE\Netscape\Administration".
<LI>Delete the "Hosts" and "Addresses" entries you see there (either one
of them might not be present). Don't confuse the "Addresses" entry,
which you should delete, with the "Address" entry, which you should NOT
delete.
<LI>Close the registry editor, then restart your administration server
by going into the Services control panel and stopping then starting the
"Netscape Administration" service.
</OL>
Now try again to access your administration server. Remember, the URL
will be something like "http://servername:12345/", where
"12345" is where the administration server's port number goes.
If you still get the same "Unauthorized host" error, then make sure that
your "ns-admin.conf" file really doesn't contain any "Hosts" or
"Addresses" lines any more, and try stopping your administration server
again then starting it back up.
Once you have access to your administration server, you can try again to
set up the access controls you want.
<UL>
<LI>For the administration server on a 3.x server installation, select
"Admin Preferences" from the General Administration page (the first page
you see when you connect to the admin server), then click on "Superuser Access
Control" and enter hostname and IP address restrictions. If you want
allow access to multiple clients, you'll have to use wildcard patterns
(separate the subsrings with a pipe character, like
"(host1|host2|host3)"); the substrings must be enclosed in parentheses, as shown.
If you're setting up hostname restrictions, you'll need to make sure that
your DNS can resolve those hostnames -- it's generally safer to stick
with IP address restrictions. When you're finished configuring this,
click "OK" then restart your admin server.
<LI>For the administration server on a 2.x server installation, select
"Configure Administration" from the Server Selector page (the first page
you see when you connect to the admin server), then click on "Access
Control" and enter hostname and IP address restrictions. If you want
allow access to multiple clients, you'll have to use wildcard patterns
(separate the subsrings with a pipe character, like
"(host1|host2|host3)"); the substrings must be enclosed in parentheses, as shown.
If you're setting up hostname restrictions, you'll need to make sure that
your DNS can resolve those hostnames -- it's generally safer to stick
with IP address restrictions. When you're finished configuring this,
click "OK" then restart your admin server.
<LI>For the administration server on a 1.x server installation, select
"Configure Administration Server" from the bottom of the Server Manager
page, then enter hostname and IP address restrictions. If you want
allow access to multiple clients, you'll have to use wildcard patterns
(separate the substrings with a pipe character, like
"(host1|host2|host3)"); the substrings must be enclosed in parentheses, as shown.
If you're setting up hostname restrictions, you'll need to make sure that your
DNS can resolve those hostnames -- it's generally safer to stick with IP address
restrictions.
When you're finished configuring this, click "Make These Changes" then
restart your admin server.
</UL>
If you still find yourself getting an "Unauthorized host" error message,
you can use the above steps to open up access and try different
settings.

Windows Server 2012R2 fails to get update from WSUS with error code 80072ee6

Hi all,
I've deployed WSUS role on a Windows Server 2012R2 machine. WSUS listen on port 8530. Now I'm trying a test server (this machine runs WIndows Server 2012R2 too). I've configured a GPO but when I try to check for updates I get the errore in the subject.
I've checked windowsupdate.log and theese are the settings of the client:
AIR Mode is disabled
2014-02-05 12:59:00:357
776 fe0
AU # Policy Driven Provider: http://MyWSUS.MyDomain.local:8530
2014-02-05 12:59:00:357
776 fe0
AU # Detection frequency: 22
2014-02-05 12:59:00:357
776 fe0
AU # Target group: CSM Servers
2014-02-05 12:59:00:357
776 fe0
AU # Approval type: Pre-install notify (Policy)
2014-02-05 12:59:00:357
776 fe0
AU # Auto-install minor updates: No (User preference)
2014-02-05 12:59:00:357
776 fe0
AU # Will interact with non-admins (Non-admins are elevated (User preference))
I confirm that from the test server I can telnet to my wsus server on TCP port 8530

Hi,
This issue occurs if the URL under the Group Policy setting 'Specify intranet Microsoft update service location' is invalid.
You receive a "80072EE6" error code when you download an update from Windows Server Update Services in Windows 7-based or Windows Server 2008 R2-based
computer
http://support.microsoft.com/kb/2724184
Make sure that the URL is correct and the name can be resolved.
Hope this helps.

I have a new mac book pro. i am using a usb not associated with my mac. when trying to download films onto the usb it keeps saying no space on it but its not full what can i do?

i've just bought a new macbook pro retina. i am using a usb not assocciated with this mac. when i try to download movies onto the usb it keeps coming back saying its full when i know there is plenty of space left. what can i do to correct this problem? do i need to buy a new usb? thanks

empty your trash
then open disk utility and reformat it
as mac journaled if you only want to use it for a mac
if you want to use it for both mac and PCs, select the partition tab, choose 1, format exfat and MBR under options
enjoy

SCOM 2012 SP1 SQL Server 2008 R2 Clustering Monitoring?

We have a new print management system that was setup using SQL server 2008 R2 clustering. Right now we have SQL MP (monitoring)(discover) 6.3.173.1. They had a failover occur a week ago and SCOM didnt throw any alerts. As a temporary
fix, I found some correlated events and setup a monitor for those events on the servers. However, the system owner wants to know if there is a MP that will monitor for a SQL cluster failover event. I have looked and looked and cant seem to find
anything that gives a whole lot of detail on this.
Thanks
EFD
Warm Fuzzies!

Yes, you can monitor SQL Cluster 2008 using SCOM 2012 SP1. but you need to install SQL MP and Windows Cluster MP and Enable proxy Agent on physical nodes.
You can refer below link {it's same for SCOM 2012}
http://blogs.technet.com/b/birojitn/archive/2010/04/14/sql-server-2008-cluster-monitoring.aspx
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"
Mai Ali | My blog: Technical | Twitter:
Mai Ali

Using StandAlone Hyper V Server 2008 R2 - clustering service not start - with error code 2 when you try to start the service

Similar Messages

Maybe you are looking for