Using the AirPort Express to Join an existing Wireless Network

Hello,
I am hoping you can provide me with some help on this... I recelty acquired a PowerMac G4 with a 450 MHz processor, CD-RW/DVD-ROM drive, Zip Drive, 1 GB RAM, and two 40 GB HD... The system has OS 10.4 installed, and it is has built-in Ethernet...
I was told I could use the Airport Express to connect to an existing wireless network, so I purchased an Airport Express base Station... Thing is, to e honest, I am having a bit of a problem getting started...
- First, to connect from the AirPort Express to my G4, do I need a special kind of Ethernet cable, or will the usual kind do?
- Second do I need to istall the software first, or have the Airport express connected to the G4 before I do?
How would I go about setting this up, step-by-step?
Any information would be appreciated...
Thanks for your time...

OK, thanks. Hopefully, the Netgear is creating a wireless network using WPA/WPA2 security. That will make it much easier for the AirPort Express (AX) to join the wireless network. It can join networks with using WEP security, but password issues almost always arise using WEP.
Since you must enter the exact security settings and password for the wireless network, it would help tremendously to know this in advance. Otherwise, it's going to be a series of "trial and errors" and likely frustration, later on.
When you have a moment, check the security settings on the Netgear router.
It might be one of the following: WPA2 Personal, WPA/WPA2 Personal, WEP 128, WEP 40.

Similar Messages

  • Can I use the Airport Express to create a secure wireless network in a wireless-only hotel?

    Can I use the Airport Express to log onto an unsecured hotel wireless network, without an ethernet cable, to create a secure wireless network for my MacbookAir, IPad, IPhone, etc.? If so, how is that done?

    will the Airport Express allow you to log onto a hotel wireless network, and broadcast a secure wireless network in your room for your wireless devices, like the Ipad, Iphone, etc.?
    The bottom line with a single AirPort Express is no.
    The AirPort Express can only "extend" a wireless network when the network is being provided by another Apple router.
    As you might imagine, it is extremely unlikely that that the hotel network....which no doubt uses professional wireless access points provided by a manufacturer of commercial systems.....would be compatible with an AirPort Express.
    In many years of travel domestically and internationally, I cannot recall a time when a single AirPort Express would "extend" the signal provided by a hotel's wireless network.
    However, if you had two AirPort Express devices handy, you might be able to configure one to "join" the hotel network and provide an Ethernet signal to the second AirPort Express, which would be configured to "create" your own "private"  wireless network.

  • Can't get AirPort Express to join LINKSYS WRT54G wireless network

    After several unsuccessful attempts to follow Tesserax's advice to get my AX to join my LINKSYS wireless network, I depressed the reset button, plugged the AX in, and waited for the flashing reset confirmation. Reconfiguring from scratch to join my WPA network, all seemed to go well. After selecting to Update, the following window pops up:
    <The settings for this AirPort Express have been successfully updated. You can close this window or wait for this AirPort Express to restart.
    Waiting for the AirPort Express to restart…>
    After a couple of minutes the following window appears:
    <AirPort Utility was unable to find your AirPort Wireless device after restarting.
    The settings for this AirPort wireless device have been successfully updated, but there was a problem re-joining the wireless network or finding the AirPort wireless device. You may need to select your network from the Wi-Fi menu and try again.>
    At this point, AirPort Utility will no longer recognize the AX, no matter how many times I rescan. The only way I can get it to be recognized is to once again do a hard factory reset. I then go through the whole set up process again, only to end up in the same dead end. I'm thinking that there has to be some sort of problem between the AX and the LINKSYS. Prior to the above activity, I was able to send iTunes to the AX just fine. I just wasn't able to surf the Internet at the same time.
    Any ideas you might have will be appreciated.

    Thomas - I have a very similar problem - I've got a Wi-Fi/ADSL2 router supplied by my telecom company AirTel (the router's called 'beetel', 802.11g model) and I'm having problems extending it with Airport Express - the Airport Utility doesn't seem to be able to detect the AE after restart. The only difference with your case seems that you have a Linksys piece.
    Here's what I tried:
    1. Had my Wi-Fi network up & running with the beetel router (network name: PASTA)
    2. Booted Airport Express
    3. Launched Airport Utility 5.5.3 from Windows 7, detected the Airport Express, chose Manual Setup and went for option "Extend my Wireless Network" and chose PASTA and specified its password
    3. Airport Utility restarted the device after saving changes, and Aiport Express went invisible.
    That sounds like the same problem you had.
    Just to cross check, I tried connecting an Ethernet cable between AE and the beetel router and went for option "Create Wireless Network" and that was a breeze.
    @Tesserax - can Airport Express smoothly extend only an Airport Extreme WiFi network? Is there anything I can do to extend my current Wi-Fi network from this router?
    Thanks for your notes & time
    Forrest

  • Can Airport Express n join a Linksys  wireless network ?

    If I already am able to connect to a g airport express, is there anything else that would be keeping me from getting a n unit to connect? I have a Linksys Wireless-N broadband router. I was able to start and go through the initial setup of adding two new n units but when they restarted my mac said there was an error in connecting to them. Am I overlooking something, is my system obsolete or inappropriate or is there something wrong with the units?
    Any advice is well appreciated.

    Since Apple designed the "extend" feature on their products to only work with other Apple routers, it would be extremely unliklely that this would be compatible with a Linksys product.

  • Using apples airport express to extend a linksys wireless network

    HI there,
    Is it possible to configure the apple airport express to extend a linksys wrt120N wireless network? if so how? 

    So the concern that you expressed regarding to that if the apple airport express is N technology kind of extender then it may extend a linksys wrt120N wireless network... But before configuring the apple airport express try upgrading the firmware of the Router and then reset the router.....
    After resetting the router power cycle the whole network and configure the Router again as per  ISP ( Internet Service Provider ) setup...

  • How do I use the airport express to connect a remote PC via ethernet cable and access the internet via wireless connection, How do I use the airport express to connect a remote PC via ethernet cable and access the internet via wireless connection

    Trying to connect my xbox to the airport express. Have wireless in home and do not have a ethernet point behind tv/xbox. How do I configure the airport express to connect to my wireless network and then the airport express can use its connection via ethernet to connect the xbox to the internet.

    Is your AirPort Express Base Station (AX) a 802.11n model? If it is, you can reconfigure it as a wireless Ethernet bridge or ProxySTA. This would allow the AX to join another wireless network and have its Ethernet port enabled for wired clients, like the Xbox 360.
    To activate ProxySTA, you must set up the Express to join a wireless network and then enable the Allow Ethernet Clients setting; both settings are located in the Wireless tab of AirPort Utility.

  • Can I use airport express to create a local wireless network that my apple tv can connect to for AirPlay/mirroring in student halls/dorm without Internet connection

    Hi I was wondering :
    Would I be able to make a local wireless network using airport express that my apple tv can connect to which in turn is connected to a projector with hdmi in so that I can mirror/AirPlay from iPhone pad and mac

    will the Airport Express allow you to log onto a hotel wireless network, and broadcast a secure wireless network in your room for your wireless devices, like the Ipad, Iphone, etc.?
    The bottom line with a single AirPort Express is no.
    The AirPort Express can only "extend" a wireless network when the network is being provided by another Apple router.
    As you might imagine, it is extremely unlikely that that the hotel network....which no doubt uses professional wireless access points provided by a manufacturer of commercial systems.....would be compatible with an AirPort Express.
    In many years of travel domestically and internationally, I cannot recall a time when a single AirPort Express would "extend" the signal provided by a hotel's wireless network.
    However, if you had two AirPort Express devices handy, you might be able to configure one to "join" the hotel network and provide an Ethernet signal to the second AirPort Express, which would be configured to "create" your own "private"  wireless network.

  • I currently have wireless, but i am looking into this to maybe have faster wireless. if this is hooked up, will the existing wireless/ethernet to pcs still function without changing them to use the airport express?

    i currently have wireless, but i am looking into this to maybe have faster wireless. if this is hooked up, will the existing wireless/ethernet to pcs still function without changing them to use the airport express?

    let me fix this a bit. i currently have dsl and a 2wire wireless router, and i currently do not have one or a mac. im getting one for when i start college and this is a must if it will improve my internet. but i now connect wirelessly to the 2wire router. if this is set up, will the current 2wire wireless still be useable?

  • I am unable to join my existing wireless network with new AirPort Express

    I am unable to join my existing wireless network with new AirPort Express.
    I am using a DLink DI-524 Router, Windows 7 (64), and the AirPort Express.
    AirPort Utility will not recognize the AEX wirelessly, it will only recognize it when it is connected by Ethernet. I can then configure the AEX and verify that the settings stick once disconnected and then reconnected. However, even after that, it will not recognize the AEX once disconnected from the Ethernet cable.
    I followed the suggestions of several other threads on these forums. But I am unable to get the AEX to work.
    Any suggestions? Thanks in advance.

    Welcome to the discussion area!
    It's almost always a security setting that causes problems when the Airport Express (AX) tries to join a third party wireless network. The AX usually does not "join" correctly and that's why you can't see it on your wireless network using AirPort Utility.
    Using an ethernet cable is still the more reliable way to configure and adjust the AX, but if you are want to try to configure it using wireless, you must return the AX back to factory defaults as follows:
    Power down the AX
    Hold in the reset button +and keep holding it in+ as you plug the AX back in to power
    Release the reset button after 10 seconds
    When it is set to factory defaults, the AX broadcasts a wireless signal with a network name like "apple network xxxxxx" where the "x's" are either letters or numbers. You must look for this network by clicking on the fan shaped Airport icon at the top of the screen. If you don't see this network, then click Join Other Network to search that way. Unless you connect to this network, you will not be able to configure the AX using wireless.
    Do you know the exact security type that your D-Link router is using? That is the key element in the process.
    Open AirPort utility, click Manual Setup
    Click the Base Station tab to establish a name for the AX, device password and adjust time zone settings
    Click the Wireless tab
    Wireless Mode....Join a wireless network
    Wireless Network Name...must exactly match your D-Link wireless network name
    Enable ethernet clients if you want the port to be active (your D-Link must be compatible with ProxySTA for this to work)
    Wireless Security...exact setting of the D-Link network. WEP security causes a lot of issues. Try to use WPA/WPA2 Personal, which is far more secure.
    Wireless Password...must match the D-Link network
    Click the Music icon to enable AirTunes
    Click Update to save settings
    Any luck?

  • Joining an existing wireless network with airport express

    Ok, am almost to the point of throwing my AX across the room
    AM trying to join an existing wireless network, its from a 2Wire gateway
    one of three things happen
    it won't find the AX in the first place
    it recognizes it, but i can't connect to it
    it goes through the configuration and when it restarts the AX, it can't reconnect to either the router or the AX and it fails. if this happens i can't reconnect to my wireless network without deleting it and re-adding.
    it doesn't show up in my available wireless networks at all
    protected via WEP, and i have tried using all the security options.

    The directions are in KB 302153, AirPort Express: How to join an existing wireless network in client mode.
    Are you using MAC address access control in addition to WEP?
    Turn off WEP and see if that makes a difference?
    One of the problems with WEP is that the actual standard relies on a 10 character HEX key for 40bit WEP and a 26 character HEX key for 128bit WEP.
    In order to make things easier for people, vendors use certain algorithms to convert simple alphanumeric passwords (or passphrases) into HEX keys, thus enabling people to use simple memorable WEP password rather than lengthy HEX keys.
    The problem is that different vendors use different algorithms to generate the HEX key and therefore a ASCII password on an AEBS will be hashed differently on a Netgear client and vice versa.
    One thing is a 13 character 128 bit WEP password will be hashed by all vendors in the same way (if you use 40bit WEP then a 5 character password is required).
    Though sometimes not even that works and the HEX key must be used regardless.
    Choosing a password for networks that use Wired Equivalent Privacy (WEP)
    http://docs.info.apple.com/article.html?artnum=108058
    WEP is now considered not to be secure and therefore it is advised you use WPA.
    "WPA Personal" on the Mac corresponds to plain WPA, with a pre-shared key (PSK) and TKIP encryption, on non-Apple wireless routers. The same alphanumeric password should work on both.
    iFelix

  • Using the airport express

    I am interested in streaming my iTunes music to my stereo. The airport express is ofcourse perfect for this but I have a few questions before I spend the money on this. I want to make sure I can do this.
    I have an iMac up in my bedroom connected to a netgear wireless router. It is however connected using an ethernet cable and not wirelessly. I am using the wireless for my iBook downstairs in my kitchen. I don't want to extend the range of my network at all and I know I can't because my router dosen't support WDS. If my iMac is connected by cat 5, can I still stream music to the airport express on a seperate wireless network? Do I need to be on the same network as the airport express exclusively? I want to only use the airport express only for sending music to my stereo downstairs in my living room. Can the airport express be a device on my existing network??? I will not be using it for printer sharing or internet connection. Can this be done????
    Thanks for your help!!!

    I found the answer in the FAQ on the support page. I can set it to join the network in client mode. I went out and bought one and it connected in a snap and I am playing music all over my house!

  • HT3728 I do not need another wireless network but want to use the airport express for printer access only.  Can this be done and how?

    I do not need another wireless network but want to use the airport express for printer access only.  Can this be done and how?

    You can configure the AirPort Expess to "Join a wireless network" and enable the Ethernet port so that Ethernet devices will be able to connect.
    In order to print from the iOS devices, you will need to have an application like Printopia installed on your Mac. The Mac must be active when you want to print.
    More details here: Printopia - AirPrint to Any Printer - Print from iPad - Print from iPhone ...
    There is a free trial available for Printopia, so make sure that it will work before you buy the AirPort Express.

  • I want to use the Airport express to have wireless music through a home amp and speakers.

    My problem is that I have a wireless router (from Telstra - Australia) on one end of the living room and then the stereo amp at the other. It is my understanding that the only way to connect everything is to have the wireless router plugged into the airport express and then the amp connected to the airport express my the rca cable. Is there another way as I do not want a rca cable running the length of my living room.
    What i am trying to say is can the wireless router (from Telstra - Australia) talk to the airport therefore meaning I can have the airport sitting behind the stereo out of sight with no massive cables in my living room?
    Help please..

    Yes, simply have the Express "join" your existing wireless network in client mode.

  • Can you use the Airport Express A1264 as an AP and a DHCP server at the same time?

    Can you use the Airport Express A1264 as an Access Point and a DHCP server at the same time?
    I would like to use it as a DHCP server and AP at the same time in my LAN (no internet, just local machines through a few switches). I was lead to belive this could be the case from a few networking friends that haven't been friendly enough to help me out setting it up.

    I need it to act as a dLink/Cisco/Linksys/etc basic wifi router, in the fact that you can access it via wifi, and it will spit out DHCP addresses (192.168.1.xxx) to everything wired downstream of it.
    I want to simultaniously provide a Wifi connection and a LAN connection at the same time
    Thanks,
    BRad

  • Can I connect multiple Mac's using the Airport Express?

    As subject. I have got an Intel iMac and a MacBook. Can I connect them using the Airport Express? Or in another word, to create a network among them that I can see the other Mac on one Mac?
    Sorry, if I raised a silly question. But really like to know.
    Many thanks in advance.
    Gary

    Can I connect them using the Airport Express?
    Yes
    Or in another word, to create a network among them that I can see the other Mac on one Mac?
    Yes

Maybe you are looking for