Using the iChat video conferencing with a PC user

I have been trying to use the iChat AV with a PC user who is on AIM. Is this not possible? Even a one-way chat?

Unfortunately this is the only way I use iChat... I can't convince my relatives to make the apple jump. It will not work one-way, only if both sides have video. When it does work it works ok, but the windows side generally has all kinds of configuration issues (like personal firewall problems). It also isn't that great of an experience on the windows side, but that is just my opinion after using hte mac side.
There are some really good folks in the ichat forum with a LOT of great information on how to get this working correctly. But for the most part the problem is going to be on the other (pc) end. The one other person I do video chat with is a mac user in New Zealand and I am in the US - when we connect I never have a problem...
Good luck!

Similar Messages

Video Conferencing with AIM PC users

If a PC user has an AIM account, does this mean that I can video chat with them?

HI Randy,
What If Your Girlfriend Lives A Long Way Away ?
This page deals with links to The Tuning instructions for AIM 5.5 and 5.9
It also detaisl how to Enable the AIM application through the XP Service Pack 2 Firewall. Trillian Come s in two versions which also need to be enabled through the XP firewall
Trillian's Basic version can Audio chat to iChat that AIM can not. The Pro version cost $25 to be able to Video but the pic is bigger (than AIM)to start with and is adjustable up to Full Screen.
How Do I Get Audio Aand Video Chats with PCs ? FAQ
EZ Jim's Blog same subject
Ralph

IChat video conferencing problems with D-Link WBR-1310

Howdy,
I am having a few problems with iChat video conferencing. I use the D-Link WBR-1310 wireless router and a MacBook. My girlfriend has a MacBook Pro at her school which she connects to via ethernet. I connect to my router via wireless. The routher is connected to a DSL modem. iChat video conferencing tends to work sometimes but very rarely. I have DMZ on the router turned on as i read somewhere on these forums that it was recommended. I also have the Apple firewall turned off so my laptop is pretty much naked as far as security is concerned. Three other computers use the network One desktop PC connected directly into the router and two Apple iBooks which are connected via the wireless. The problem is that i keep getting error message -8. Can anyone please help?
Thanks in Advance

I'd start by verifying you have the most recent firmware installed on your router.
Next, start off by trying to test to a user that has no known issues: http://www.ralphjohnsuk.dsl.pipex.com/ContactTesters.html (Bottom of the page)
That will help pinpoint where the connection issue lies.
Once you can succefully connected, then you should set up a static ip address on your mac and port forward the necessary ports in your router. If you router supports UPnP, I'd try enabling the first.
I hope this helps!

Satellite A105- S4384 - How to use the s-video port

What is the way to use a s-video cord to connect my 4384 to use TV as a screen?
I use Linux Ubuntu 8.04... thanks

Hi
Usually you dont need any special workarounds to establish the connection with the external TV.
You have to connect the notebook with the TV using the s-video cable.
Please note that the s-video channel should be enabled on your TV.
Then you could change the video output in the graphic card properties.
Using a Windows OS, you would be able to switch to the external TV pressing the FN+F5 buttons but as far as I know on Linux OS this feature will not work.
Greets

What do I need to connect my Mac Mini to a TV using the S-video jack?

Radio Shack didn't have anything in the store and suggested
that what I needed (something with an S-video connector
at the adapter end and a co-ax/F-connector at the TV end)
would cost $100.
What should I be looking for? I'd like the option to connect
my Mac Mini to a TV (with enough resolution to read text,
which isn't the case with a video-RCA cable), especially in
a hotel room (using the Mac Mini as a laptop!).

The DVI to video adapter
<http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/6454000/wo/jP1F dznaaoNs2dPRALa1K0FqrB2/3.0.21.1.0.8.25.7.11.2.3>
will give best results using the S-Video. Next best is composite video. If your TV set does not have either of these, you will need a RF modulator to connect to the TV antenna connector. For best results get a modulator that takes S-video. It should cost a lot less than $100.00 Radio Shack has one for $25
<http://www.radioshack.com/product/index.jsp?productId=2103095&cp=&origkw=rfmodulator&kw=rfmodulator&parentPage=search>
No matter what connection you use, a standard TV will not give you better than 640 x 480 resolution, so it will always be hard to read small text.

Blue screen when attempting to use the dedicated video card

I keep getting a blue screen when attempting to use the dedicated video card.
I managed to install the AMD driver for it but without the other components like the Catalyst Control Center as it blue screened on startup when attempting to load the Catalyst Control Center.
The OS loads fine. Any applications that don't use the dedicated video card runs fine. All other drivers install fine as well.
Applications like games and Photoshop that switch to the dedicated video card on startup automatically crashes, the OS freezes then a blue screen appears.
What could be causing the problem? This problem just recently appeared. Two weeks ago.

boogs wrote:
I tried installing the drivers for my laptop from HP's support site. Still the same result.
This problem only appeared a few weeks ago. Before that, the same drivers from the HP site installed and functioned normally.
Could this be a problem with the graphics card itself?
Note sure but if we can know the system P/N others can look to see what drivers it has for the graphics to know what is there.
I am a Volunteer to help others on here-not a HP employee.
Replies aren't online 24/7 because of Time Zone differences.
Remember in this Day and Age of Computing the Internet is Knowledge at your fingertips if you choose understand it. -2015-

Does the ipod video work with the original ihome?

does the ipod video work with the original ihome?

Welcome to Apple Discussions!
If you mean this one...
http://www.ihomeaudio.com/products.asp?productid=10015&deptid=1003
Them yes. I am using one myself. You may want to purcahse these if it does not come with them (depending on how old it is)
http://www.ihomeaudio.com/products.asp?productid=10016&deptid=1000
btabz

I am unable to view the full content of various web pages after purchasing Advanced System Care Pro. I was using the free version before with no problems. I cannot figure out if or which setting was changed. Please help

I am unable to view the full content of various web sites after purchasing Advanced System Care Pro. I was using the free version before with no problems. I cannot figure out if or which setting was changed. I tried doing a system restore but that did not work. I tried turning off all features of ASC pro but that did not work. Javascript is enabled. Please help.
Brian

Many thanks.
With those symptoms, I'd try the following document:
Apple software on Windows: May see performance issues and blank iTunes Store
(If there's a SpeedBit LSP showing up in Autoruns, it's usually best to just uninstall your SpeedBit Video Accelerator.)

Using the New Video Features in Photoshop CS6 | Photoshop CS6 Feature Tour | Adobe TV

Adobe Digital Imaging Evangelist Julieanne Kost shows how to use the new video features in Photoshop CS6.
http://adobe.ly/I5cUF2

I am removing a dust spot from video clips taken during an aerial shoot. I have discovered that the only effective way to remove these spots effectively is to use PS6 and go frame by frame using the paint brush, clone stamp, and spot healing brush. It is very time consuming and mind numbing but the only thing that works with all tha movement of the aircraft and the ground below.
My question:
Right now to advance the clip one frame at a time - I must magnify the time line so to see the frame by frame lables. To advance to the next frame I must remove my cursor from the work area and go down to the time line and click on the next frame.
How can I advance to the next frame with a keyboard stroke and not move my cursor out of the work area?
Thank you in advance for any help.
Tony

Using the 5g ipod together with itunes 6?

Hi there,
i was wondering if its possible to use the new ipod along with itunes 6? without using the video or game options? just the music..
gr. &thx!

Sure. You don't have to have iTunes 7 to use the 5g iPod.

Can I use Elgato VHS Video Capture with my Macbook pro?

Can I use Elgato VHS Video Capture with my Macbook Pro? It comes with a CD on which is the software. My Macbook pro does not have a CD drive. how do i get the software?

Elgato provides a download link to their latest Video Capture software v1.1.5. Supposedly runs on Snow Leopard and later. They recommend Yosemite.

How can I use the old Apple TV with new iTunes? It tells me to input a code in iTunes but iTunes no longer has a spot to input this code to allow sync. I can access the iTunes Store fine, just none of my Library

How can I use the old Apple TV with new iTunes? It tells me to input a code in iTunes but iTunes no longer has a spot to input this code to allow sync. I can access the iTunes Store fine, just none of my Library

read this
https://discussions.apple.com/message/20429789#20429789

Issues with using the output redirection character with newer NXOS versions?

Has anyone seen any issues with using the output redirection character with newer NXOS versions?
Am receiving "Error 0x40870004 while copying."
Simply copying a file from bootflash to tftp is ok.
This occurs for both 3CDaemon and Tftpd32 softwares.
Have tried it on multiple switches - same issue.
Any known bugs?
thanks!
The following is an example of bad (NXOS4.1.1b) and good (SANOS3.2.1a)
MDS2# sho ver | inc system
system:    version 4.1(1b)
system image file is:    bootflash:///m9200-s2ek9-mz.4.1.1b.bin
system compile time:     10/7/2008 13:00:00 [10/11/2008 09:52:55]
MDS2# sh int br > tftp://10.73.54.194
Trying to connect to tftp server......
Connection to server Established. Copying Started.....
TFTP put operation failed:Access violation
Error 0x40870004 while copying tftp://10.73.54.194/
MDS2# copy bootflash:cpu_logfile tftp://10.73.54.194
Trying to connect to tftp server......
Connection to server Established. Copying Started.....
|
TFTP put operation was successful
MDS2#
ck-ci9216-001# sho ver | inc system
system:    version 3.2(1a)
system image file is:    bootflash:/m9200-ek9-mz.3.2.1a.bin
system compile time:     9/25/2007 18:00:00 [10/06/2007 06:46:51]
ck-ci9216-001# sh int br > tftp://10.73.54.194
Trying to connect to tftp server......
|
TFTP put operation was successful

Please check with new version of TFTPD 32 server. The error may be due to older version of TFPT server, the new version available solved this error. Files are getting uploaded with no issues.
1. Download tftpd32b.zip from:
http://tftpd32.jounin.net/tftpd32_download.html
2. Copy the tftpd32b.zip file into an empty directory and extract it.
3. Copy the file you want to transver into the directory containing tftpd32.exe.
4. Run tftpd32.exe from that directory. The "Base Directory" field should show the path to the directory containing the file you want to transfer.
At this point, the tftpserver is ready to begin serving files. As devices request files, the main tftpd32 window will log the requests.
Best Regards...

I am using the "G Web Server" with Bridgeview 2.1. The problem I am having is that I have to

restart the web server once every 2 to 3 days, or the web pages don't show the vi (images). Any ideas to trouble shoot - I dont know if the problem is related to my workstation hardware or a setting that needs to be tweaked on the G Web Server. Thank you.I am using a Pentium 233 machine/ Win 95. The PLC I am collecting info from is a GE Fanuc Series 9030 (?). Ethernet connection.

restart the web server once every 2 to 3 days, or the web pages don't show the vi (images). Any ideas to trouble shoot - I dont know if the problem is related to my workstation hardware or a setting that needs to be tweaked on the G Web Server. Thank you.Hi,
we are using the G Web Server with LabVIEW on a WinNT 4 machine. Up to now these works fine. Therefore I would recommend you to choose a more stable OS.
Maybe you can try to programmatically restart the server every 2 days. Within LabVIEW you would do this by running "HTTP Server Control.vi". Unfortunatly all connections will be closed, thus be aware of that!
Hope that helps
chris

How to use the same OC4j server with different port number

How to use the same OC4j server with different port numbers..?
I have to OC4J installed on my machine on different hard disk drives....
I want to be able to run both the server simultaneously..?
is it possible ..it yes then how..?
for that i have changed the port number of one server...
but when i am trying to start the other server with different port number..it says that JVM -Bind already...
Is there any clues...?
Nilesh G

In the config directory:
default-web-site.xml: Change the port the HTTP listener listens on
jms.xml: Change the port the JMS service listens on
rmi.xml: Change the port the ORMI listener listens on.
Or, you can add another web-site.xml file, and deploy your applications to 1 server, and bind the web applications to the different web sites. This way you only have to deploy your applications to 1 place.
Rob
Oracle

Using the iChat video conferencing with a PC user

Similar Messages

Maybe you are looking for