Using the Local Director "alias ip address" command

I believe it is possible to have real servers in a different subnet to the local director virtual address by using the "alias ip address" command. This eliminates the need to use a router between the Local Director and the real servers. Does this mean that the Local Director is routing between subnets? Do the real servers use the Local Director alias address as their default gateway? Can someone provide an example config using the "alias ip address" command?

no, the local director will not route. there are two ways to make this work.
1
the router on the front side of the local director must be configured with a secondary ip address from the real server subnet plus add the alias command
or
2
use the alias command, plus each real server must be configured with a static ARP entry. the ARP entry is for the ip address of the servers configured default gateway and the MAC address of the router interface.

Similar Messages

  • Using the Local Director static command

    A few questions:-
    1. I understand that this can be used to change the source IP address for real server oubound connections. Please confirm if this is just for connections that are initiated by the stipulated real servers.
    2. I have a group of servers already being load balanced by a virtual using port 80 and want to use the static command to change the source IP address for connections that are initiated by the real servers to port 80. Could some just provide a few lines of sample config for this. Many Thanks

    Yes, for outbound connections that the real server makes (not in response to a user accessing the virtual server), the IP address is translated to the virtual IP address identified by the static command. If the real_ip exists as a real server, then the outbound connection is counted toward the number of connections for that real server (that is, it will affect load balancing); otherwise, the connection is only translated and does not affect load balancing.
    I am not sure about the static configuration for a particular port. Anyone else would like to comment?

  • I am not able to access the sharepoint:80 site using the local IP address.

     I am able to access the Central administration using the Local LAN IP address and the port number, but, I am not able to access the sharepoint:80 site using the same local IP address without the port for the central administration. I tried adding
    the local IP address in the Alternative Access Mapping to no avail. Any ideas, where I should look, is much appreciated.

    Hi，
    By my test, I set the Alternative Access Mapping for the SharePoint 80 port web application as below and it works fine:
    Thanks,
    Eric
    Forum Support
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
    [email protected]
    Eric Tao
    TechNet Community Support

  • How to use the local storage space in OVM 3.2.1

    Hi
    We have installed OVM 3.2.1 in a server , which has 1TB HDD and 350GB RAM and we have installed the OVM manager in a seperate machine.
    I am able to identified the server in the manager console but how can i use the local storage space.
    Kindly help us to solve this issue.
    Regards
    Niranjan

    Hi,
    if you want to import an ISO image, why you mount it?
    after you complete your installation.
    1- discover server. (if your installation is finished good, then you found your server in Onglet Servers and VMs / unassigned servers)
    2- Go to Perspective / Physical Disk to verify that detect the second partition
    3- if it's good, then crearte a pool with no Clustered Server Pool.
    4- create a repository on your physical disk.
    5- Go to ISOs in your repository and click import iso image.
    Now, verify that your apache/httpd server it is working or not.
    1- after you install apache/httpd
    2- you shoud verify if it is running or not (pgrep httpd) if not start it (e.g. service httpd start )
    3- copy the ISO file under /var/www/html
    4- open your browser and verify.
    and at this point i think it is good.
    then copy the url to import the iso file with Oracle VM Manager
    the URL Look's like http://IP-Address/image-iso.iso
    you should verify that the IP-Address is reached from the Oracle VM Server.
    and that's it
    I tested it: and in my case:
    i have copied the windows iso image:
    cp ../windowsXP.iso /var/www/html/
    and now my URL is like * http://IP-Address/windowsXP.iso*
    I hope this can help you
    Best Regards

  • My husband and I both have iPads and somehow when they were setup the both we're setup using the same email I'd address. When I go to delete and rename one iPad it says all info and pictures will be erased from my iPad. Is there a way to keep the info iPa

    My husband and I both have iPads and somehow when they were setup the both we're setup using the same email I'd address. When I go to delete and rename one iPad it says all info and pictures will be erased from my iPad. Is there a way to keep the info IPad when doing this?

    You can go to Settings/iCloud and delete the account, then create a new iCloud account.  You can still use the same account for the app store though.

  • Help!!!!!! OS X wants to use the "local items" keychain. Please enter password. I have tried every password that I know of. Nothing works! I haven't even set up a password for this

    Help!!!!!! OS X wants to use the "local items" keychain. Please enter password. I have tried every password that I know of. Nothing works! I haven't even set up a password for this

  • Does the 10.5.7 update address command+f finder search issues?

    Does the 10.5.7 update address command+f finder search issues?
    Search has been horrible under 10.5 in that it does not reliably find FOLDERS on network drives, only file names.
    Even when I am looking directly at a folder and I search for it will not appear in the command+f window.
    Also the stupidity of not allowing a specific search location.
    Has this been addressed? I have, at any given time, 3-4 mounted servers.
    I do not have a choice now to search a specific hard drive.
    10.4.11 gave me the option under "OTHERS" to select a specific place to search.
    The only choice I have in 10.5.2 is "SHARED". Which searches all drives when I only want to search one. Nor do I have a choice of searching just one of my two internal drives.
    I talked with Chris in apple engineering several months ago, who acknowledged that search problems are a known issue under 10.5 and this was being addressed but have not heard any more. I don't want to download an update unless these broken search issues have been fixed. This is a production machine and I cannot have downtime in the Dept.

    Have you filed a bug report or enhancement request with Apple?
    http://bugreport.apple.com/

  • HT1529 Upon startup my iMac has a popup that says: "talagent wants to use the local items keychain."  New to me--can't get anywhere.  How do I get out of this and get things up and running again?

    Upon startup my iMac (OSX Mavericks) has a popup (that I can't get rid of!) that says: "talagent wants to use the local items keychain."  I never set this up, don't want it, and want my iMac to start up with my desktop in place and ready to work.  I'd appreciate some help please.  How do I get rid of this?  Thanks.
    Larry

    I found this and it fixed my issue..
    I was suffering with this same problem, I followed these steps and everything returned to normality:
    1.- I opened KeyChain app and run the FirstAid (from the KeyChain app Menu)with my user Password (this do work) because the problem is not with your password. If there is any trouble with your keychain file this will fix it.
    2.- Opened Disk Aid and run Fix Persmissions just in case there was left some wrong file permissions during the upgrade.
    3.- Went back to the Key Chain App and Locked and Unlocked the Keychain using the Lock in the top left corner of the app. When asked for my password I simply typed my User password.
    After this everything worked fine. These are the steps that I followed but I really think that #3 did the trick here. You could try to do only #3 directly and it might fix your problem, but fixing the Keychain and fixing OS permissions is never a bad Idea.
    Good Luck friends.

  • Is it possible to use the Internet User Alias?

    Hi,
    We are currently authenticating users against an LDAP datasource and pulling back the employee id as the SAP username in order to provide the correct authorisations. The problem with this is that we then have to create another user account for people who require R/3 access via the GUI.
    What we want to be able to do is to use the Internet user alias against their R/3 account so that we essentially only have 1 account to maintain for each user.
    Does anyone know how this can be achieved?
    Thanks in advance!
    Keith

    If you are using ABAP for your UME user store, the LDAP IDs are probably stored as aliases in the backend ABAP system. If that's the case, your users already have corresponding, automatically generated, backend R3 IDs. Trying searching by alias for one of your web users and see if there is a user master record for that user. They can log into SAPGUI using that auto-generated ID, although you may need to assign a password first. From the user perspective, it will still seem like they have two different accounts though, since the login ID will be something new for sapgui.
    http://help.sap.com/saphelp_nw70/helpdata/en/52/67119e439b11d1896f0000e8322d00/content.htm

  • Using the retouch tool, how do you make it change color? The old iPhoto one did, this one seems to be flesh-tone only, which is not how I need it to be. In old iPhoto, used the local color to blend, it was great.

    Using the retouch tool, how do you make it change color? The old iPhoto one did, this one seems to be flesh-tone only, which is not how I need it to be. In old iPhoto, used the local color to blend, it was great.

    I don't know which old version you're referring to but iPhoto 6's,  7's and 8's retouch tool works exactly the same as iPhoto 9's. The color of the enhance tool's area while applying is a light brown color but the retouch works on any color using the surrounding colors as a basis.
    During retouching:
    After retouching:
    OT

  • Using the local db in the netweaver developers workplace

    hi guys,
    is it possible to use the local db of my developers workplace?
    I am planning to create jsp-pages in the netweaver developers studio (nds) and want create some db-table for my  application (create and update statements). how can I access the local db in the nds? do I need a special jar-file like in jdbc to handle the communication with the db?
    In a later step I want to migrate this application into the local sap portal.
    thanks
    thorsten

    hi thorsten,
    the access information about your local max-db is shown in the sapmmc.
    the preferred way to access databases is by using jdbc datasources
    --> http://help.sap.com/saphelp_nw70/helpdata/en/b0/6e62f30cbe9e44977c78dbdc7a6b27/content.htm
    and the following link to get familiar with driver class and connection string:
    --> http://help.sap.com/saphelp_nw04s/helpdata/en/43/313c13198d0d26e10000000a1553f7/content.htm
    or: Can we connect from Portal to MaxDB with the trial version of SAPNetWeaver?
    hth, regards and merry x-mas to you, too
    regards, jens

  • Is there a way to give a local user permission to add a local user using the local group policy editor?

    I need to find a way to have the local administrator of a Windows Server 2012 system grant a local user (non-administrator) the ability to add a user for the machine using the local group policy editor. The machine is not part of any Active Directory environment,
    this is strictly on the one machine.  In my situation it is not an option to just make the user an administrator. The idea is to give someone the right to add a user and have no other such administrative rights. I need to accomplish this using the
    Local Group Policy editor or the Group Policy Management Console if it is possible to do this outside of an active directory environment. This is not an assignment to learn how to use these tools and I am not even sure if it would even be possible though I
    need to either find a way or find proof that it is not possible using these applications.

    Hi,
    Sorry for the delay reply.
    So did you want to non-admin user have the ability to add another user?
    As far as i know, we cannot add the user if we have no local admin permission, we will receive the error"Access denied".
    Regards.
    Vivian Wang

  • Hi, I am new to Mac and i managed to install and configure all the services. Now my issue is when i sending mail using the local server to internal, mail are not receiving. Mail queue showing Connection refused error. Please help me

    I am new to Mac and i managed to install and configure all the services. Now my issue is when i sending mail using the local server to internal, mails are not receiving. Mail queue showing Connection refused error. Please help me
    Thanks
    GIRI

    Try this -> http://support.apple.com/kb/TA38632?viewlocale=en_US

  • Project for web using the program Director 11

    I have a project, a game for kids, that want to run on a web site. I developed it, originally to use it in the computer. But now, I want to migrate it to a web site (the game´s web site), the kids will play it on line. The idea is to have a web site and in the web site an option to play it on line, by clicking that option, the game will start (in order to play it, you have to pay a fee).-
    So, I published it for web (I click the option ".html", saved it and published it). I downloaded the "Adobe shockwave Player", installed it and everything, opened the project (wich is in my computer) using a browser, and works perfectly.-
    But .... I uploaded to a hosting and doesn´t work.-
    My question is:
    What should I do in order to run perfectly the project on line (having the project in the hosting ...). The hosting should have a special requirements? Should I program the icon that opens the project in a special way?? The project should be in a different (new) window when the persons click the icon?
    I will appreciate all the information and help about it!!!!

    I have taken a quick look at you site.
    yes, I am seeing your problem
    sometimes says 'unable to find '***.dir"    not .drc?
    also some of the pathnames had capital letters in them - which might make a difference.
    an example:-
    Director Player Error
    Unable to open file "http://www.mggim.com.ar/pantallaFinal.dir"
    It seems that your site is cut into many different .dcr programs.
    I'll take a longer look at them - and get back to you...
    I normally inbed my '.dcr' files (linked - to the file stright from the web) into my main controlling program - then I do a 'preLoadNetThing' routine, to make sure it's preloaded before I jump to it.
    ( I use the file > import > internet > "File URL: http://www.mggim.com.ar/lola.dcr" )
    But their are a few different ways to control shockwave files
    I'm going to do a test and see if you can jump to another 'dcr' file without preloading it, or inbedded it first.

  • Using the equivalent of a BREAK ON command in SQL Developer SQL window

    Folks.
    In SQL*PLUS "BREAK ON Col1 ON Col2;", I can generate a report similar to the following:
    Col1Value1 Col2Value1 Col3Value1
    Col3Value2
    Col3Value3
    Col2Value2 Col3Value1
    Col3Value2
    Col3Value3
    Col1Value2 Col2Value1 Col3Value1
    Col3Value2
    Col3Value3
    Col2Value2 Col3Value1
    Col3Value2
    Col3Value3
    etc.
    I want to be able to do the same thing in my SQL Developer SQL window so that I can export the results to a spreadsheet file.
    Does anyone know if this is possible?
    I've tried using the SQL*PLUS BREAK command in my SQL Developer window but it appears to be ignored. My resultset looks something like
    Col1Value1 Col2Value1 Col3Value1
    Col1Value1 Col2Value1 Col3Value2
    Col1Value1 Col2Value1 Col3Value3
    Col1Value1 Col2Value2 Col3Value1
    Col1Value1 Col2Value2 Col3Value2
    Col1Value1 Col2Value2 Col3Value3
    Col1Value2 Col2Value1 Col3Value1
    Col1Value2 Col2Value1 Col3Value2
    Col1Value2 Col2Value1 Col3Value3
    Col1Value2 Col2Value2 Col3Value1
    Col1Value2 Col2Value2 Col3Value2
    Col1Value2 Col2Value2 Col3Value3
    .

    OK thanks.
    I did get around this by using SQL*PLUS to generate an output file with a separation character between the columns and spooling the SQL*PLUS output to a text file.
    I then open the text file with Excel and specify the same character as a column separator. Seems to load properly into Excel.

Maybe you are looking for