Using the "silicon controller" on the MSI NEO4 PLAT SLI, quick question!

I have a stable OC w/ my FX55 (261x11) 2.87GHz, but now I want to use the Silicon Controller, and not just my NVIDIA controller. Does the MSI NEO4 PLAT SLI "LOCK" the silicon controller, so since my FSB is OC'ed, I dont want any problems.... By not using all 4 ports on the NVIDIA controller, will this maybe "relax" the nvidia controller, and not let it work so hard, or does it not matter. (overall speed wise)

Quote from: newls1 on 12-April-05, 08:06:00
I have a stable OC w/ my FX55 (261x11) 2.87GHz, but now I want to use the Silicon Controller, and not just my NVIDIA controller. Does the MSI NEO4 PLAT SLI "LOCK" the silicon controller, so since my FSB is OC'ed, I dont want any problems.... By not using all 4 ports on the NVIDIA controller, will this maybe "relax" the nvidia controller, and not let it work so hard, or does it not matter. (overall speed wise)
All of the PCI-E devices are locked, so that includes the SiI3132 controller and the Marvell Gigabit NIC. One note, it's best to use the SiI3132 "last". AnandTech did a benchmark of the two controllers, and the onboard nVIDIA controller was faster, although the 3132 PCI-E controller was much faster than the competitions use of PCI based SiI3112 controllers. If you've already used your nVIDIA controller for 4 SATA or SATA II devices, then by all means use the SiI3132 without overclocking fear.

Similar Messages

Cant go above 235fsb with MSI neo4 plat SLI

I have started OCing my rig and it seemed to be going very well until 235fsb, now i have reached 2.35gig on the 3200+venice and DDR470 2.5-3-3-7 timings, and this is @Vcore1.45, 1.6chipset voltage and 2.7 RAM voltage, i tested for stability with SuperPI 16mb test and it finished successfully.
the problem is that whenever i try to go beyond these speeds SuperPI never completes the 4mb or higher tests, i upped the Vcore to 1.51 and lowered the RAM to DDR200, but it seems like no matter what i do i can never finish the test not even at 2.37gig,
any ideas??
::EDIT:: i have come across something on hardocp review for this mobo:
"It seems that the board is limited to a 235MHz FSB with the Aggressive timing option in the BIOS Cell Menu screen enabled. Anything above that FSB and the system will not post. However, it is a vastly different story with the Aggressive timing option disabled."
now i am sure that i have disabled agressive timings, but i still have the same problem.
pls help.

I suggest you read the sticky above about overclocking a neo4 board, disabling a couple of bios settings is required, including cpu spectrum among others, you need to do some research before you make a statement like " I can't or it won't", you havent done your homework on this, and it kind of sounds like you have posted here to get some quick and easy answer..... you are going about this backwards in my opinion, if you would have researched you would have already known about this disabling of bios settings....before you go ahead any further I suggest that you take some time to get the basics down first or else you are going to hit a lot of unecessary brick walls and you might end up doing damage to your system, upping voltage is to be used with caution and not as a quick fix, your bios settings and lack of knowledge are the only thing holding you back right now, and btw expect for it to take a couple of days to get it down right, ocing is about careful and caculated trial and error and it usually isn't something you can do off the top of your head, different boards over clock differently, then throw in the variable of which speed of ram you are using, what type of ram, your cpu cooling solution, your power supply, lots of variable to work through...get my drift.
Good luck and have a good day.

MSI Neo4 Plat/SLI missing Creative Audio Enable/Disable in BIOS

Alright I thought I was having some driver issues, but apparently it is a bit more in depth than that. I recently just updated my BIOS thinking I may get a resolution that way but i guess not. I was browsing the large thread about this board and noticed that someone made mention of just disabling the sound in the BIOS and using an external solution. Well there isn't an option in the BIOS. I know where to look...looked there before seeing the thread...I don't have a creative labs audio option in my BIOS. Didn't have one in the original BIOS either...I did spend some time in it before flashing it.
What could be causing it not to show up in the BIOS.
The board has been a bit squirrely...I can't get the onboard 1394 to actually find some available resources...I have seen posts where someone was having the same problem with the PCI Express Bridge (or something to that effect). I would be willing to just pop in another sound card, but I have my suspicions that something worse is going on, and the sound and 1394 are just symptoms of a larger problem.
I have seen the issues of usinga non -5v PS with this board. Although the problems seems to be functionality, not availability as is my case.
Any ideas before I make a phone call to MSI, I would hate to RMA this board as it has all of my condensation measures already in place.

We've had reports of missing bios items b4, they've been the 1394 & gigabit options.
Some have been solved by slackening mobo srews by 1/4 - 1/2 turn, or checking & finding surplus mobo risers which were causing shorts. Bios items missing
After eliminating that think it's get in touch with MSI time - sorry
luck

MSI Neo4 Plat SLI. Help with sli setup (rma time)

Hi everyone.
I'm new to the sli world. I am having an issue with setting up the second video card. Runs great with one card as soon as I install the second card and try to play a game or run 3dmark03 the screen goes blank and the system reboots. I reversed the sli card made sure it was seated good, enabled the nvidia settings to dual cards.
Is there a bios setting? I might be missing or something. Please help this newbe, I'm getting frustrated.
Thanks.

Anyone?????? I am going to RMA this sucker.....Updated to 3.30 and now it doesnt see the other video card. try to shut down and it reboots....aaaahhhhhhgggg .......Can not get a hold of MSI tech support (Non existant).....Hmmmm should tell me something.
Sorry for venting

Neo4 plat SLI raid configuration

I made a striped raid config from my 2 160gig SATA drives in SATA 1 and 2. but when i tried to install windows on it, it didnt recognize the raid config and saw it as 2 seperate hard drives. I tried SATA ports 3 and 4. and it made no difference. then i tried 5 and 6. but it uses an old raid controller and it worked fine and i installed windows on it. BUT, im about to reformat and i want to use the newer raid controller. I have the MSI neo4 plat SLI mobo. But i saw that my mobo came with 2 floppys and i only installed 1 of the floppys during windows install... do i need to install both of them? I guess that might be why it didnt work... but can anyone assure me thats the problem? I didnt think i needed both of them...

Quote from: lupolian on 13-February-05, 06:09:50
I made a striped raid config from my 2 160gig SATA drives in SATA 1 and 2. but when i tried to install windows on it, it didnt recognize the raid config and saw it as 2 seperate hard drives. I tried SATA ports 3 and 4. and it made no difference. then i tried 5 and 6. but it uses an old raid controller and it worked fine and i installed windows on it. BUT, im about to reformat and i want to use the newer raid controller. I have the MSI neo4 plat SLI mobo. But i saw that my mobo came with 2 floppys and i only installed 1 of the floppys during windows install... do i need to install both of them? I guess that might be why it didnt work... but can anyone assure me thats the problem? I didnt think i needed both of them...
YOU HAVE TO INSTALL BoTH DRIVERS ON THE NVIDIA FLOPPY,THE RAID DRIVER AND THE MASS STORAGE DRIVER. HIT S TWICE TO DO IT. The other floppy is for the silicon image drivers,dont use it unless you use ports 5 and 6.

I'm trying to use a madcatz controller on the mac but it turns on for 2 seconds and turns off. the system profiler picks it up as a xbox 360 gamepad but says its not been configured. how can i allow my self use this with my games.

i'm trying to use a madcatz controller on the mac but it turns on for 2 seconds and turns off. the system profiler picks it up as a xbox 360 gamepad but says its not been configured. how can i allow my self use this with my games!

I have exactly the same problem.
I'm a little peed-off with Microsoft on this. The original wireless controller I have doesn't work either since the cable I'm using is 'just' the charge and play cable, so a direct connection to my Mac won't work with this cable. It's a cable for god's sake. Why on EARTH put any limitations on this!?!?
Next I learn I need an additional USB wireless receiver from Microsoft to get my original 360 controller to talk to my Mac. As I certainly don't want to fork any more microsoft dollars on this, this is not an option.
Next I think, yes! I have a MadCatz 360 wired USB controller. This should surely do the trick just plugging it in and the way I go. But oh no, for some reason I plug my MadCatz Xbox360 controller in, it flashes a few times then switches off and can't be turned on again.
The System Profiles recognizes it as a MadCatz 360 device controller but that is about it, but the ontroller software I download for the System Prefs (360Controller, USBOverdrive etc) don't even recognize the controller as being plugged in.
What the **** Is The Microsoft Deal with all of this!?!?
PS: Oh, and I forgot to mention, there are No drivers for device 4716 that I can find on the MadCatz website, or am I going blind?
If anyone has a link, it would be appreciated.
Message was edited by: nostrawaggus

The box indicating that this domain controller is the last controller for the domain is unchecked. However, no other Active Directory domain controllers for that domain can be contacted

I have 2 domain controllers running 2003 server, server1 and server2. I ran dcpromo on server1 and removed AD and removed him from the domain and disconnected from network. I then added a 2012 server
with the same name and IP address server1 with no problem. Replication from sites and services work fine on both controllers.
The new 2012 server1 is GC. I transferred all FSMO roles to server1. Again no problem and replicating using sites and services. AD on server1 is populated correctly.
Now what I had intended on doing was a dcpromo to remove server2 from the domain so I can then add another 2012 server. That is when I get the: "The box indicating that this domain controller is the last controller for the domain
is unchecked. However, no other Active Directory domain controllers for that domain can be contacted.
I have DNS installed on both servers and both look good with replicating there. Strange thing is when on the 2012 server within DNS if I right click and connect to another DNS server I can add server2 just fine but from server2 adding server1 it tells me it
is not available.
Help please!

Hi,
As there is server 2012 DC (SERVER1) DC is operational in a domain then "This domain controller is the last controller for the domain" should be remain unchecked when you demote SERVER2 DC.
If you are getting error "Active Directory domain controllers for that domain can be contacted" while demoting SERVER2 DC then check the DNS pointing on both as per below article, disable windows firewall on all DC, less possiblities but worth to check if both
are different site then check the ports are open on firewall.
http://abhijitw.wordpress.com/2012/03/03/best-practices-for-dns-client-settings-on-domain-controller/
http://technet.microsoft.com/en-us/library/cc766337(v=ws.10).aspx
http://social.technet.microsoft.com/wiki/contents/articles/584.active-directory-replication-over-firewalls.aspx
run “ipconfig /flushdns & ipconfig /registerdns“, restart DNS server and NETLOGON service on each DC and try to demote server2 DC.
If issue reoccurs, post dcdiag /q result.
NOTE: If initial replication was completed between both DC (new 2012 and old DC) then you may remove the server2 DC from Active Directory forcefully (DCPROMO /FORCEREMOVAL) and perform metadata cleanup.
Active Directory Metadata Cleanup
http://abhijitw.wordpress.com/2012/03/03/active-directory-metadata-cleanup/
Best regards,
Abhijit Waikar.
MCSA | MCSA:Messaging | MCITP:SA | MCC:2012
Blog: http://abhijitw.wordpress.com
Disclaimer: This posting is provided "AS IS" with no warranties or guarantees and confers no rights.

Reference to the component controller in the window

Hello All,
Can we get the reference of the component controller in the method of the window..
Warm Regards,
Smita

Vinod..hard luck ...!!!...
This is what i get..!!!...The interface IF_POWL_TABLE has no such method to retrieve the reference for the component controller...:-(....
Web Dynpro Comp. / Intf. POWL_TABLE_COMP,Web Dynpro Window POWL_TABLE
Pre-Exit PST46K50FS40BKOKLYAGE0SR3P6M for HANDLEDEFAULT
Method "GET_COMPONENTCONTROLLER_CTR" is unknown or PROTECTED or
PRIVATE.
Web Dynpro Comp. / Intf. POWL_TABLE_COMP,Web Dynpro Window POWL_TABLE
Pre-Exit PST46K50FS40BKOKLYAGE0SR3P6M for HANDLEDEFAULT
Method "GET_COMPONENTCONTROLLER" is unknown or PROTECTED or
PRIVATE.
Web Dynpro Comp. / Intf. POWL_TABLE_COMP,Web Dynpro Window POWL_TABLE
Pre-Exit PST46K50FS40BKOKLYAGE0SR3P6M for HANDLEDEFAULT
Method "GET_COMPONENTCONTROLLE_CTR" is unknown or PROTECTED or
PRIVATE.

Helo, anybody knows what the chipset controller of the firewire port's mac book pro 13 i5 i7, please thanks

helo, anybody knows what the chipset controller of the firewire port's mac book pro 13 i5 i7, please, thanks!

Try the notebook forums, not the workstation community.
http://www.apple.com/support/macbookpro
or Google

Memory not recognized on MSI Neo4 Platinum SLI

I just installed another 512mb of RAM on this system:
MSI Neo4 Platinum SLI
2 x 512mb Corsair XMS XL PRO
1 x 512mb Corsair XMS XL (the one that doesnt work)
IDE HDD
Windows XP PRO
BIOS, and every program i run that can see system specs shows that the infact all 3 Sticks
are recognizable. Though...Windows and a program that shows me my physical memory max both
point out i have only 1 gig of RAM!?
It's there, just not being used?
Now the only difference with the XL version and the XL PRO version is the heatspreader,
everything else is the same....so nothing should be conflicting.
Since the computer somehow knows all my part's details..im thinking just because
the new ram doesnt have PRO that it may not be recognized to work together.
Even so...ram should downclock etc with this motherboard...so this stupid little name
issue shouldnt cause the computer to ignore the ram!
I tried switching DIMM slots, no luck.
Any ideas?

It's a AMD64 dual memory channel system motherboard/CPU.
Valid memory populations are
1.stick in one of the channels .(single mode 64bits)
1.stick in each channel .(dual mode 128bits)
2. sticks in one of the channels.(single mode 64bits)
4.sticks ,2 in each channel.(dual mode 128bits)
3 sticks is n/a.
The population on memory controller , it's initialization and modeselection , single/dual mode is chosen by the A64 cpu.
It's been said that later rev.E cpus can autoselect unmatched population between channels (of e.g 3.sticks) and
set the whole memory pool in single mode.
But i have never seen anyone successfully test/run it .

Newbie with MSI neo4 Plat

hey there,
my 1st post here.
MOBO: MSI Neo4 Plat
Graphic: MSI 7600GS
CPU : AMD X2 3800+
power supply: 500W
recently i got this problem. Randomly my display goes blank, like the PC is on standby. The pc seems to be running but the monitor seems to be set to standby.
after i restart the PC(only able to do by the reset button, cannot Ctrl+Alt+del) everything seems to be ok.
the problem seems to occur randomly.
anyone have any idea what's going on here?
thanx for reading.
cheers!

Quote from: okta on 02-June-06, 00:35:16
hey there,
my 1st post here.
MOBO: MSI Neo4 Plat
Graphic: MSI 7600GS
CPU : AMD X2 3800+
power supply: 500W
recently i got this problem. Randomly my display goes blank, like the PC is on standby. The pc seems to be running but the monitor seems to be set to standby.
after i restart the PC(only able to do by the reset button, cannot Ctrl+Alt+del) everything seems to be ok.
the problem seems to occur randomly.
What kind of monitor, how is it connected and does it use calibration software. I've seen this with Samsung (and some OEM brands made by Samsung) monitors, which use Magictune, connected to the DVI port. Basically Magictune is crap ands clobbers the monitor's EDID info so that it switches to the VGA port - you can check this by plugging in the VGA cable. Depending on the monitor, it can cause permanent damage to the monitor's firmware which requires a firmware re-burn... or as apparently in your case, temporary damage which is fixed with a reboot. The only solution is to get a newer version of Magictune.. or dump it completely.

MSI Neo4 Plat. SLI

MSI Neo4 Plat. SLI
FX-55
Antec 550 True Power
NEC DVD Rom
2GB OCZ Platinum Ram
and a single 7900 GTX
I was browsing some forums last night, and suddenly heard a loud *CRACK* from my computer. ???
The computer froze, but did not turn off.
Attempted a hard boot, and nothing not even a POST responds.
Popped open the content's, to see what might have happened.
And under the edge of my video card I notice that the SLI Switch Card has come loose. The little black plastic thing that was supposed to keep it in place had popped out. I attempted to place it back in to see if this would correct the problem (afraid it will not), but it will not stay securly lodged into place.
Any suggestion's on how to get the SLI Swicth Card Black Pin thing to work, or a work around to it, in order to test the system and see what, if anything else might have blown before I go for an RMA?
Thank you for any help or suggestions.

With regards to the small black pin that holds the SLI card in place, I have to admit that its a very poor design from MSI. I can think of two ways to fix it, and both would require you to strip the mobo down and remove it from the case.
1: would be to build up the "small ball" part of the pin with a blob of glue,(epoxy) so that it cant pop thru the small hole in the mobo.
2: Same idea as the first but using a hot knife or a soldering iron tip to flatten out the "small ball" part of the pin. (BE VERY careful not to over do it).
Best option tho would be to RMA the board.
Its the loud crack that you heard that worries me tho. Was it the physical sound of the SLI bridge card coming out or was it more of an electrical type crack that you heard?
Best thing to do would be to strip back to bare basics and try to go on from there, ie one video card, one memory stick and one H/Drive, Reset the BIOS, and set BIOS to boot from cd and see what happens.
As for getting a new pin from them, I would drop them an email, depending on where you live they might be able to post one to you.

MOVED: Neo4 Plat/SLI + Winnie.. Is MSI a respectable company? How can I trust them now?

This topic has been moved to Overclockers & Modding Corner.
Neo4 Plat/SLI + Winnie.. Is MSI a respectable company? How can I trust them now?

It seems strange that after you simply swapped a heatsink that your mobo blanked out.
Fiirst, you should check to see if your power supply is still working.
Second, if you psu is working, you need to go to the simpliest setup....1 vid card, 1 hard drive, 1 floppy, 1 stick of ram, etc and see if you can boot...just my 2 cents.

MOVED: K89 NEO4 PLAT/SLI Do I have to send it back?

This topic has been moved to AMD64 nVidia Based board.
K89 NEO4 PLAT/SLI Do I have to send it back?

No worries.
As for the Bios flash all you need to do with a newer core top get it to come up for posting or Bios Adjustments/Flashing is to use a single Stick of RAM. That forces the CPU's Memory Controller into single channel and that will get it done. If you try to post in dual channel with older Bios's that do not fully support a newer chip it will lock and you need then just to remove all RAM except from Slot 1 and reset the Bios as per your user manual.
No worries as it is not as hard as it sounds.

Can anyone explain this bizarre Neo4 plat/sli circumstance?

Just had mobo upgraded to Neo4 plat/sli. I only have IDE drives in the system currently. They are PHYSICALLY connected in this way:
IDE socket 1 cable
master - 80GB HDD, empty drive
slave - DVD burner
IDE socket 2 cable
master - 120GB HDD, OS installed here (WIN XP PRO SP2)
slave - 120GB HDD, data resides on this disk.
HOWEVER...
The drives are being recognized at bootup in this way:
Primary Master - 120GB HDD with OS (physically on IDE socket 2 as master)
Primary Slave - DVD Burner (physically on IDE socket 1 as slave)
Secondary Master - 80GB HDD (physically on IDE socket 1 as master)
Secondary Slave - 120GB HDD with data (physically on IDE socket 2 as slave)
Further, the WIN XP disk management utility shows the drives in a similar manner:
Disk 0 - 120GB w/ OS (drive C:)
Disk 1 - 80GB (no drive letter)
Disk 2 - 120GB w/ data (drive E:)
DVD burner - (drive D:)
How can this be? I thought that to show as primary master, a drive must be connected to IDE socket 1 as master? And how in the world can the Primary master and slave drives reside on two different IDE cables?
I didn't do this installation and cannot talk to the tech who did until Monday. FWIW, everything is working just fine. And it all appears to be jumpered properly. But before I go about the process of loading up all my software, etc., I feel a need to understand why this is happening. Is this a function of a bios setting that I can't find?
Can anyone help?
Thanks so much!

Well, in the first place welcome to the forum, secondly what you present it's correct, the system drive (OS drive) it has to always be the drive C: that's not a question of Master and Slave because if you go to the system properties you will see those drives as they are configured in the BIOS.
But for me that is a strange configuration....
Be well....

Using the "silicon controller" on the MSI NEO4 PLAT SLI, quick question!

Similar Messages

Maybe you are looking for