Using Time Capsule to extend a wireless network

I have an office in the top of my house (2nd floor roof conversion) and as a result the wireless signal from the ground floor is very weak. i would like to boost the signal using my Time Capsule, placing it on the 1st floor, shortening the distance the signal has to travel.
Is this possible? In the AirPort settings I can seen an option to 'extend a wireless network using an ethernet cable' but if that is the only option I may as well just move my wireless home hub to the 1st floor.
Can the network be extended wirelessly?
many thanks!

Thanks for the clarification.
Unfortunately, the "extend a wireless network" feature of the AirPort Express is only compatible with an Apple base station.
Therefore, you will not be able to use the TC to extend the wireless network that has been created by the BT Home Hub. You might check to see if BT offers an "extension device" or "remote" that would allow you to expand your wireless signal.
The TC will need to be configured to "Join" the wireless network that you have there.

Similar Messages

Can I use a Time Capsule to extend my wireless network.

Hi, I have just bought a 3TB time capsule as my old (flat style) 500GB TC is reaching full capacity. The old style TC will then be surplus to requirements as a data storage unit, at least for myself, though it might be useful for my son to use as his Time Capsule.
Ideally, as we have a wireless 'blind spot' out in the rear extension of the house, it would be useful to use the unit to extend my wireless network (and also use it as a separate TC if possible). Is this possible? If it is how would I go about it?
Hope someone can help . . . .
Cheers
John

Is it possible for you to consider connecting the Time Capsules together using a wired Ethernet connection?
Here is what Apple has to say in their support document about extending:
Adding Wi-Fi base stations when it is unnecessary can reduce Wi-Fi throughput because the Wi-Fi network will require more data management overhead. The network configuration also becomes more complex. In the case of a wirelessly extended network, throughput may be reduced to less than 60 percent of that of a single device. The general rule is to keep the Wi-Fi network as simple as possible. You can accomplish this by using the minimum number of Wi-Fi base stations required to service the physical network area and by using Ethernet wherever possible.
Extending the range of your Wi-Fi network by connecting Wi-Fi base stations together using Ethernet is always the best option, and will provide the best throughput.
Wi-Fi base stations: Extending the range of your wireless network by adding additional Wi-Fi base stations

When I change the setting on my third generation time capsule to "extend a wireless network", the update fails. Why?

I purchased a new router. Everything is working great except for a third-generation time capsule which will not accept a change from join a wireless network to extend a wireless network as it did before. Does anyone know how to fix that?

You cannot extend a non-apple router..
So what new router did you buy?? If it don't have an Apple Symbol on it.. it aint gonna work.

Unusual Senario: Use Time Capsule to extend Airport Express network

I have an less common senaria here. I'd like to keep the TC on my desk and hide away the ugly cable modem. This is what I want to accomplish:
- Connect my airport express (802.11n model) to the cable modem and use it as the base station, in b/g/n mode.
- Wirelessly extend the above network to my TC.
- The TC will only be connected via ethernet and N equipped computer, so I want to run it in N (5GHz) only mode.
After some research, it seems to be not feasible, can anybody please confirm? Thanks for help.

If you are asking about extending using wireless only......Yes, if your existing network is being created by another Apple wireless router.
In this case, the Time Capsule would need to be located where it can receive a strong wireless signal in order to extend it correctly.

Problems using time capsule to extend wireless network

Hi all,
For some months I had to move to Germany for work (I'm from Italy, sorry for my English).
I am sharing internet with some other people, the wi-fi router is in their apartment, so basically I don't have access.
As the signal is strong enough only in one room I would like to use my time capsule to extend it also in the other rooms.
But when I try to extend it, my macbook pro connects to the network I would like to extend and the time capsule is not seen anymore.
To see the time capsule again in the airport utility i have to reset it to factory default.
Do you have any idea?
The wireless network is WPA2 protected, the provider is the German "Unity Media".

As the signal is strong enough only in one room I would like to use my time capsule to extend it also in the other rooms.
Apple's "extend" feature will only work if the Time Capsule is "extending" the wireless signal from another Apple wireless router. In other words, the "extend" feature is not compatible with wireless routers from other manufacturers.
You will need to connect the Time Capsule to the wireless router using a wired Ethernet connection. Connect from one of the LAN <-> ports on the wireless router to the WAN "O" port on the Time Capsule. Then, you can configure the Time Capsule to provide a separate wireless network for your use.

Can I use my Time Capsule to extend a current network? If so, How?

Can I use my Time Capsule to extend a current network? If so, How?

I want to use it wirelessly to extend the range of the network. I currently have an xfinity router as the main.
You may not have understood what I was trying to say above.
If you want the Time Capsule to extend wirelessly, then you must have an Apple router as your "main" router.
You have an xfinity router. You cannot use the Time Capsule to extend the range of an xfinity router wirelessly.

I was using time capsule to extend a network. now i want it to be the primary base station. how do i convert this?

i was using time capsule to extend a network. now i want it to be the primary base station. how do i convert this?

Thanks for the info. Since this is a cable modem, you will need to fully reset it so that it will associate correctly with the Time Capsule when it is reconnected.
I don't have the manual for your Ubee model handy, but most modems will reset if you power them down completely. That means pulling the power cord from the back of the device or unplugging from the wall. Leave the modem powered off at least 30 minutes...longer will not hurt a bit.
Next, perform a Factory Default Reset on the Time Capsule per this document:
Resetting an AirPort Base Station or Time Capsule FAQ
After the modem has been powered down and Time Capsule has been reset, connect an Ethernet cable from the modem to the WAN port (circle icon) on the Time Capsule.
Power up the modem and let it run for 2-3 minutes by itself
Then power up the Time Capsule and let it run a minute or two
Next, open AirPort Utility and configure the Time Capsule to "Create a wireless network". Let us know what operating system you are using on your Mac or PC if you have additional questions or need more details on this.

Using time capsule to extend a network with security

I have a time capsule and my roommate and I use the same wireless network. I want to add my time capsule to the network we both share but want to be sure only I will be able to access data on my time capsule i.e. external hard drive, back ups etc. Is this possible?

The Time Capsule can only extend a network wirelessly if it connects to the wireless signal from another Apple router.
So, the first question here would be whether or not the existing wireless network there is being provided by another Apple router.
If yes, what model of router would this be?
If no, then the Time Capsule will need to connect to the existing wireless router using a permanent, wired Ethernet cable connection.
If you do it this way, you have the option to have the Time Capsule produce a separate wireless network, or you can turn off the wireless on the Time Capsule and use it only as a wired hard drive.
No matter how the Time Capsule is set up, you would want to set up a separate Disk Password for the Time Capsule, so only those users who had the password could access the Time Capsule hard drive.

I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help

I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help.
They said I need to change my settings to NAT settings. I haven't been able to figure out or find anything. I have also spoken to Apple Support on the phone for hours without being able to figure out how to do this ( i don't think he knew much either lol.) Please help me because I've got about 15-20 devices in my house that require to be connected to the internet and this is just making things ridiculously slow and painful for me.
Thanks!

It is on DHCP & NAT under router mode yet my isp is still the one issuing ip addresses to my devices instead of the router issuing them

How can I set up a time capsule to extend my wifi network from a non-apple Medialink MWN-WAPR300N?

I just purchased a new Medialink MWN-WAPR300N from Amazon to replace my old 2008 500 GB Time Capsule.
I was wondering if it would be possible to use my old Time Capsule to extend the network from the Medialink router to the rooms in the back of my house. Would this be possible? How about if I use the Time Capsule as the primary point, and use the Medialink router to extend the network?
Thanks!

The Time Capsule would not be compatible with a Medialink product if you are thinking of trying to use the Time Capsule to extend the Medialink network using wireless only.
The same would be true if the Time Capsule were the primary router, and you tried to use the Medialink product to extend the Time Capsule network wirelessly.
If you can connect the two devices together using a permanent wired Ethernet connection, then you should be able to accomplish your goal.

Installing Time capsule with U-Verse Wireless Network

Hi all,
I am not a techy, but I get by. I am going to install the Time Capsule and I realized that I don't think this will work with my existing U-Verse Fiber wireless network. After some thought, I believe I should just use this for wireless backup and peripheral operations rather than the internet as my current wifi also operates the televisions in the house.
I'm hoping to get some guidance from the community as to how to use this device without having to purchase more equipment or re-wiring my entire home. Can I just plug it in and use it for wireless backup or will it interfere with my internet service (which I am happy with)?
Any thoughts?

Welcome to the discussions!
You are correct to allow your existing setup handle internet connections.
The simplest setup would be to configure your Time Capsule to "Join" the wireless network created by the U-Verse router. Your computers will be able to backup via wireless assuming that you have a good connection.
If your U-Verse router provides ethernet ports for devices (it likely does), you would also have the option of connecting the Time Capsule to the U-Verse router with an ethernet cable. This would make sense if the Time Capsule will be located near the U-Verse router as ethernet is both faster and more reliable than wireless.
Not to get too technical here, but if you connect the TC this way, you will set Connection Sharing on the TC for "Off (Bridge Mode)".
If you connect the Time Capsule via ethernet, you would also have the option to setup the Time Capsule to "create" its own wireless network. So, you would have two wireless networks available...one created by the U-Verse router and the other created by the Time Capsule.
If you have computers capable of wireless connections at "n" speeds, they could connect to the Time Capsule and your other "g" devices would connect to the U-Verse. In fact, if you purchase a new dual band TC, it will be capable of creating two wireless networks on its own.
So, you have a number of options available. Just depends on how simple or complex you want things to be.

When using time capsule on a PC based network, how does it appeare on the network ? like a normal shared external HDD ??? or what ?

when using time capsule on a PC based network, how does it appeare on the network ? like a normal shared external HDD ??? or what ?

Yes, it will show you the main directory.. so if you link in windows explorer it will be..
\\TCname\data
Or \\TCipaddress\data
Data can be whatever name the main (root) directory of the TC is called.

Using Time Capsule to extend network

Hello: I have a Belkin N1 wireless modem router (ADSL) and have my Time Capsule connected the the modem via ethernet cable. I have the modem at the moment connected to my MacBook Pro via ethernet cable, and am able to connect to the Internet in that manner. My problem is that I cannot sem to extend my wireless network with my Time Capsule, which is what I want to do. Any advice or help? Thanks in advance.

I first tried connecting my new Time Capsule to my 2Wire gateway (DSL modem and router) via the ethernet cable to form a parallel network, but some incompatibility kept messing up the gateway's settings (resulting in losing Internet and phone altogether). I have since used the Time Capsule to extend the network via wireless only. This currently seems to work, although I have lost access to the Time Capsule on more than one occasion this afternoon for no apparent reason. I have not yet been successful in further extending the network using my Expresses -- which are used to connect ReplayTVs to the network.
Unfortunately, I cannot find a way to turn off the router function on the gateway (a previous DSL modem allowed me to do this -- most recently, I had my Extreme connected up via ethernet to the 2Wire gateway and forming a parallel network).
In case I need to replace the gateway to get this to work properly and in a stable fashion, does anyone know which AT&T DSL appropriate modems are most compatible with the Time Capsule?

Using time capsule to extend a 2003 airport extreme

I have a 2003 airport extreme. I have a 2011Time Capsule. How can I use the Time Capsule to extend my range wirelessly?

Unfortunately, this is not possible, since the older AirPort Extreme does not have a setting to "extend a wireless network", which was added to the AirPort Extreme models in 2007.
It might be possible to have the older AirPort provide some additional wireless coverage if it can be permanently connected back to the Time Capsule using a wired Ethernet cable connection.

Using Airport Express to extend my wireless network

I recently purchased a Time Capsule but found that I could not see the wireless signal from my bedroom. To solve this I purchased an Airport Express to extend the range. I plugged the AE into an outlet in my bed room and set it up to join my existing network. Everything looked fine from the point of view of the Airport Utility. Unfortunately my iPod Touch still can not see my wireless network from my bedroom. I new iPad can see it but the signal is very weak, even when I hold it right next to the AE. Is there a setting I missed?

Rick, welcome to the discussion area!
I plugged the AE into an outlet in my bed room and set it up to join my existing network.
You need to configure the AirPort Express to "Extend a wireless network". The AX does not provide any additional wireless coverage when it is set to "join".
First, you need to check a setting on your Time Capsule as follows:
AirPort Utility > Manual Setup > Wireless tab (below the icons)
Make sure there is a check mark next to "Allow this network to be extended"
Update to save any changes
On the AirPort Express move it close to the Time Capsule for configuration:
AirPort Utility > Manual Setup > Wireless tab
Wireless Mode = Extend a wireless network" (Hold down the option key on your Mac if you do not see this choice appear when you click the selection box).
Wireless Network Name = Same name as your Time Capsule Network
Check mark next to "Allow wireless clients"
Security = Same setting as your Time Capsule
Password = Same password as your Time Capsule
Confirm Password
Update to save settings
The AirPort Express can only "extend" what it "receives". Most users position it too far away from the main router and consequently, the Express extends a weak signal. Try a location that is about 1/2 to 2/3 the distance between the Time Capsule and the area that needs move coverage. Then experiment a bit to find the best signal.
Post back on your results.

Using Time Capsule to extend a wireless network

Similar Messages

Maybe you are looking for