Using Two Extremes of different generations

I have a 5th Gen AEBS (AESB-1) hooked up to a 2Wire. Then I got a 4th Gen AEBS (AESB-2) given to me and I setup it up to extend the wifi network. I need to run G too. Both running 7.6.
No possibility to run additional ethernet cable between the AEBSs.
However the 4th Gen AEBS (bridge) goes yellow, after awhile. Need to reboot AESB-2 & launch AP Utility to see it. Then turn wifi on/off to connect to AESB-2 where I can get a transmit rate greater than 130 on mac mini 2010.
If I shutdown the Mini AEBS goes yellow and wind up repeating process all over if I restart Mini.
Any suggestions to keep AESB-2 in the "green"
TIA
Devices on Network wirelessly - G5 Imac, Iphone 4 &4S, Ipad (1st gen), 2010 Mini

What is the approximate distance and the number of walls/ceilings/floors between the two AirPort? What is the basic construction material in the walls/ceilings/floors?

Similar Messages

Using two or four different antennas on a 1242AG

Hello I have a little doubt, I need to cover two diferentes areas with AG, is possible to use only one 1242 with:
1-A: AIR-ANT5160V-R (Patch)
2-A: AIR-ANT5160V-R (Patch)
3-G: AIR-ANT2410Y-R (YAGI)
4-G: AIR-ANT2410Y-R (YAGI)
Or
1-A: AIR-ANT5160V-R (Patch)
2-A: AIR-ANT5195P-R (Omnidireccional)
3-G: AIR-ANT5160V-R (Omnidireccional)
4-G: AIR-ANT2410Y-R (YAGI)
Thanks in advanced.

I'm just curious as to exactly why it would not be a good idea to use two different types of antennas with diversity enabled on the same radio (1242). I thought the client made a decision on which antenna to connect to by RSSI. If that was the case, the client would see the signal and be able to communicate with both antennas ( assuming you mounted them correctly) and the client would not get disconnected. Is there a limitation on the AP for how it trades the clients off from primary and secondary antennas? I can understand if you went with an extreme like a yagi and an omni, but what about the attached image? I don't practice using different antennas, primarily because I know two of the same antennas on one radio will definitely work fine, but I don't see an obvious reason why it wouldn't work with some antenna combinations. Has anyone actually tried this to see if it causes problems? Does the client have to connect to both antennas at the same time for diversity to work? If that was the case then I can see how a directional antenna would cause a problem with an omni. Just curious...

HT201079 Purchase using two credit cards, different billing addresses.

I made a purchase using two credit cards, one is mine and the other is my mother's. We each have different billing addresses, but it is all under my billing address. Is there going to be a problem with the order?

For any order (free or paid), once it has been submitted and processed successfully, you may not need to worry about this order any more.
If you worry about this, wait for the receipt sent to your email address.
I don't use multiple credit card to make purchase so I cannot duplicate your issue. Sorry.

Using two Macs with differing OSs.   Password refused on one for purchases/updates

I'm running an old MacPro with OS10.5.8 and a 27" i7 iMac withOS10.9.5 which I use for working in FCPX.   The older MacPro still had FCP6 in use.    For a little while now Apple refuses to recognise my password for their store downloads and updates.    As I don't gain in any way by using these two differing OSs, is there a way to get Apple to accept my circumstances -and allow my excess to their Store and iTunes from either machine, please?

Anyone . . . ?    Please.

How can I use two sequences w/ different frame rates

I shot wedding (on Sony Z5) initially (1st tape) in DV widescreen (29.97/ 30 fps) but tapes 2, 3 & 4 were shot 1080p24 fps Big mistake; now obvious.
Edited all in FCP 6. On trying to cut & paste sequences together I get " cannot nest sequences with different editing timebases".
I have 23 min.intro/ ceremony sequence as stand alone QT mov now. How can I best convert that and/or merge it w/ the rest ( 62 min. 24 fps sequences), or perform other action to unite the diff frame rates into one, w/ best looking quality for the DVD/ bride & groom? Trying to beat Xmas deadline...
Thanks in advance! Happy Holidays to all.
3 Ghz Intel Core 2 Duo / 8 GB / OS 10.6.8 FCP 6.0.6

I went back and forth on this.
Ordinarily, I'd conform to the format that the majority of the footage was shot in. But if you're going to DVD, and it's going to be compressed to 480 anyway, then why not down convert the 1080 footage to 480?. At the same time, I would imagine re-timing the 24 (23.98?) to 29.97 would look reasonably consistent with the 29.97 SD.
This could be done in FCP, but I think Compressor will produce a better result. The adjustments you need are in the Settings menu in the Encoder (with Audio set to pass through), Geometry (720x480 16:9 Anamorphic), and Frame Controls (Resize Filter set to Best).
This will not be a short encode, so I would first test a short section to double check your settings and sound sync are right, and to compare against the quality of tape 1.
Good luck.
Russ

Can I do an Insert using two selects from different tables?

Hi,
I have three tables, Course (CID, NAME, TIME)
Teacher (TID, NAME, DESCRIPTION) and OfferedBy(CID, TID) to match a course to a teacher.
After I do an insert on Course, I want to be able to do an insert on OfferedBy using the CID of the course I inserted, and the TID of the teacher that's offering it.
I tried this after doing inserts on Course and Teacher:
INSERT INTO OfferedBy values (SELECT CID FROM Course where courseName = 'name' , SELECT TID FROM Teacher WHERE LastName = 'teacherName').
I get an ORA 00907 error.
What am I doing wrong? Can this actually be done?
Thank you
I

Hi,
How would you relate the TID with CID?
I tried this after doing inserts on Course and Teacher:
INSERT INTO OfferedBy values (SELECT CID FROM Course where courseName >= 'name' , SELECT TID FROM Teacher WHERE LastName = 'teacherName').
I get an ORA 00907 error.You can use the query in this way:
SQL> SELECT ( ( SELECT dummy FROM DUAL), (SELECT DUMMY FROM DUAL)) FROM DUAL;
SELECT ( ( SELECT dummy FROM DUAL), (SELECT DUMMY FROM DUAL)) FROM DUAL
ERROR at line 1:
ORA-00907: missing right parenthesis
SQL> SELECT 'AA',(SELECT dummy FROM DUAL) FROM DUAL;
'A (
AA X
SQL>Regards

Using two Nike+ Nanos and one iTunes Library

Hi,
I have a Nike+ account and a nano. I am considering buying my wife a Nike+ kit to go with her nano.
We share a single iTunes library.
Can we use two nanos with different Nike+ accounts from the same iTunes account? And both upload our runs to our own accounts without confusion?

You can always setup seperate accounts on your Mac for you & your wife & place the library in /Users/Shared/ as an alternative. However, as others have posted, the settings for Nike+ are per iPod.

Two sequences with different settings?

In Premier Pro CS6, is it OK to use two sequences with different settings?

Yes, no problem.
You can make as many sequences with differents settings as you want.

Universal OS download for different generation Phone and Touch?

I have an iPhone 3g and 3gs as well as two Touches both different generations. They are all synched to the same Macbook Pro and I try to keep the OS's on the same release as it keeps it easier... What I would like to find is a universal download for all platforms.
Each time I connect a different device there is a new 200mb+ download. I have to assume that much of that code is duplicated. If iTunes can distinguish which device is connected, why can't it identify the right pieces of the OS to install on each device? Give me a choice to download on 400mb+(random guess on universal size) file as opposed to 4 200mb+ files...

This is the way that Apple does it.
We are iphone users like you and are not privy to Apples decision making process.

SLI - Can I use two different video card versions for SLI?

Hello,
Can I use two different generations of MSI video cards that implement the same GPU for SLI?
The two video cards are:
MSI N260GTX-T2D896-OCv2 GeForce GTX 260 896MB <-- What I currently have
MSI N260GTX-T2D896-OCv3 GeForce GTX 260 896MB
MSI N260GTX-T2D896-OCv4 GeForce GTX 260 896MB
The main difference between these three seems to be that the OCv3 has two fans and a different heatsink than the OCv2. The OCv4 has one fan like the OCv2 and but it is located in a different location and some weird spikey heatsink thing going on. I already have the OCv2 but I am looking to get another card for SLI and newegg doesn't sell the OCv2 anymore. The important thing is that I am looking for is stability and it seems that the most ideal setup would be to get identical cards.
By the way, why are there so many versions (updates?) to this card? Have there been issues related to the card that necessitate a revision?
Thanks

Different coolers(HS and fans) and possibly different makers of vRAM. But, you should be able to run SLI without issues regardless of the versions.

USING TWO AIRPORT EXTREMES (802.11N) INTERNET IS VERY SLOW

I live in a 5000sq ranch in arizona and have our internet set up in one end of the house. We have an airport extreme 802.11n and it wasnt putting out a good signal to the other end of the house so we got another airport extreme and airport express to expand out network. By the way both are 802.11n and the internet is still not even usable because it is so slow. The only computer that has some sort of speed is the mac tower that is hardwired to the airport. PLEASE HELP!!!!!!!!!!!!!!!!

If you could ethernet the two Extreme N routers(try to place the second further into the house) and set the second in bridge mode and set to create its own wireless networrk. Use the manual configuration. The third can join the second, signal should reach and be strong. This must be in bridge mode also.
there are many different ways to set the configuration for wireless but the bridge mode is a must do.

Uprezzing film timeline which uses two different codecs

So I have my final film edit in FCP 6 which uses two different codecs...DVCPROHD 720p60 at 23.98fps and HDV 1080p24 at 23.98fps. There are only about 15 clips which are the HDV codec. My next step is to color correct in apple Color. So I did a quick test where I sent a couple clips of each codec, on the same timeline, into Color and back out into FCP, which seemed to roundtrip without any hitches...the only difference is that the DVCPRO clips came back as ProRes 422HQ 1280x720 and the HDV clips came back as 1920x1080...which is all fine. However, I do want 1080p (1920x1080) as my final output...for Bluray as well as DCP if my film gets picked up by a festival. So what I plan to do for my final output is export my completed Colored timeline to compressor and use ProRes 422 HQ at 1080p. My question is...since there isn't a specific 1080p ProRes HQ codec (like there is for DVCPROHD) but simply the "Geometry" tab in Compressor where you can change the 'Dimensions' to 1920x1080...is this how I "Uprez" my DVCPRO 720p clips to match my HDV 1080p clips?
I just want to make sure NOW, that my workflow will be good all the way up to finishing, before I start sending sections of my timeline to Color...
Thanks!
David

OK...you wanted a 1080p final, right? So why shrink the HDV down to 720p, and then blow it back up to 1080p? That's the point of doing both formats separately, and upscaling only the 720p...keeping the HDV at full size. How noticeable will it be? Test to find out. Personally, I'd do it my way.
And yes, upscale AFTER you color correct. As for re-color correcting down the line...why? Color correcting is the final process...do it until it's right...why would you go back? And if you did adjust a couple shots, then just render those back out, and only upscale those and put into that final sequence again. It's a small patch.
>why is it better to send the DVCPRO 720p stuff for upscale BEFORE marrying it with the HDV 1080p stuff.
because the HDV is already 1080. Scaling it down to 720, then back up will be TWO generation losses. Why do that?
>my method of upscaling the 720p with the 1080p stuff at the same time seemed logical to me (the 720p is upscaled while the 1080p stays the same)
But it doesn't...you first will be shrinking it to 720p...then blowing up to 1080p. And HDV is a GOP format without real frames, so the compression really pops when you upscale.
>just want to know WHY your method is better??
Because I tested this out..mixing 720p DVCPRO HD and HDV...and my method gave the best results. Call it "experience."

Can I use two airport extreme base station on the same network

Can I use two airport extreme base station on the same network

Here is my network setup:
D-Link DCM-202 simple cable modem (DOCSIS 2.0 compliant)
attached via ethernet to
5th generation AirPort Extreme Base Station - Main (Bought last week)
attached via ethernet to
4th generation AirPort Extreme Base Station - Remote (Bought about 11 months ago)
The main AEBS is set to:
AirPort Section:
Base Station Tab -> Allow setup over WAN is CHECKED
Wireless Tab -> Wireless Mode: Creat a Wireless Network, Radio Mode: 802.11a/n - 802.11b/g, Radio Channel Selection: Automatic, Wireless Security: WPA2 Personal
Internet Section:
Internet Connection Tab -> Connect Using: Ethernet, Ethernet WAN Port: Automatic (Default), Connection Sharing: Share a public IP address
TCP/IP Tab -> Configure IPv4: Using DHCP
DHCP Tab -> DHCP Beginning Address: 10.0.1.2, DHCP Ending Address: 10.0.1.200, DHCP Lease: 24 hrs
NAT Tab -> The box following 10.0.1. is left blank, Enable NAT Port Mapping Protocol box is CHECKED.
The remote AEBS is set to:
AirPort Section:
Base Station Tab -> Allow setup over WAN is CHECKED
Wireless Tab -> Wireless Mode: Creat a Wireless Network, Radio Mode: 802.11a/n - 802.11b/g, Radio Channel Selection: Automatic, Wireless Security: WPA2 Personal
Internet Section:
Internet Connection Tab -> Connect Using: Ethernet, Ethernet WAN Port: Automatic (Default), Connection Sharing: Off (Bridge Mode)
TCP/IP Tab -> Configure IPv4: Using DHCP, IP Address: 10.0.1.2, Subnet Mask: 255.255.255.0, Router Address: 10.0.1.1, DNS Server(s): 10.0.1.1 (Everything else under this tab is blank)
Hope this helps with info needed.

How can I send email using two different email address that both link back to my one exchange account on my Ipad mini

How can I send email using two different email address that both link back to my one exchange account on my Ipad mini?
On my PC I simply have a master return email address and use a POP for the secondary address. Both are through the one exchange account without a problem. I need to be able to do the same on my Ipad.

Ah, I should have made that clear. My domain didn't come from google. It was purchased at and is hosted at dreamhost, but I haven't used their email servers in years - I just route everything through gmail. I actually have a bunch of domains (with websites).
Gmail has an option that lets someone with custom domains send (and receive) email through gmail using the custom domain once Google confirms proper ownership of the domain (to prevent spammers and such). Gmail has a setting for "send email as" which allows gmail to be sent using a custom domain as the sender. I'm pretty sure Apple's old mobileme had this feature too, but I didn't use it.

Using two facts of two different star schemas and conformed dimensions

Hi,
I've been working as developer and database designer for years and I'm new to Business Objects. Some people says you can not use two facts of two different star schemas in the same query because of conformed dimensions and loop problems in BO.
For example I have a CUSTOMER_SALE_fACT table containing customer_id and date_id as FK, and some other business metrics about sales. And there is another fact table CUSTOMER_CAMPAIGN_FACT which also contains customer_id and date_id as FK, and some other business metrics about customer campaigns. SO I have two stars like below:
DIM_TIME -- SALE_FACT -- DIM_CUSTOMER
DIM_TIME -- CAMPAIGN_FACT -- DIM_CUSTOMER
Business metrics are loaded into fact tables and facts can be used together along conformed dimensions . This is one of the fundamentals of the dimensional modeling. Is it really impossible to use SALE_FACT and CAMPAIGN_FACT together? If the answer is No, what is the solution?
Saying "you cannot do that because of loops" is very interesting.
Thank you..

When you join two facts together with a common dimension you have created what is called a "chasm trap" which leads to invalid results because of the way SQL is processed. The query rows are first retrieved and then aggregated. Since sales fact and campaign fact have no direct relationship, the rows coming from either side can end up as a product join.
Suppose a customer has 3 sales fact rows and 2 campaign fact rows. The result set will have six rows before any aggregation is performed. That would mean that sales measures are doubled and campaign measures are tripled.
You can report on them together, using multiple SQL passes, but you can't query them together. Does that distinction make sense?

Using Two Extremes of different generations

Similar Messages

Maybe you are looking for