Using two or four different antennas on a 1242AG

Hello I have a little doubt, I need to cover two diferentes areas with AG, is possible to use only one 1242 with:
1-A: AIR-ANT5160V-R (Patch)
2-A: AIR-ANT5160V-R (Patch)
3-G: AIR-ANT2410Y-R (YAGI)
4-G: AIR-ANT2410Y-R (YAGI)
Or
1-A: AIR-ANT5160V-R (Patch)
2-A: AIR-ANT5195P-R (Omnidireccional)
3-G: AIR-ANT5160V-R (Omnidireccional)
4-G: AIR-ANT2410Y-R (YAGI)
Thanks in advanced.

I'm just curious as to exactly why it would not be a good idea to use two different types of antennas with diversity enabled on the same radio (1242). I thought the client made a decision on which antenna to connect to by RSSI. If that was the case, the client would see the signal and be able to communicate with both antennas ( assuming you mounted them correctly) and the client would not get disconnected. Is there a limitation on the AP for how it trades the clients off from primary and secondary antennas? I can understand if you went with an extreme like a yagi and an omni, but what about the attached image? I don't practice using different antennas, primarily because I know two of the same antennas on one radio will definitely work fine, but I don't see an obvious reason why it wouldn't work with some antenna combinations. Has anyone actually tried this to see if it causes problems? Does the client have to connect to both antennas at the same time for diversity to work? If that was the case then I can see how a directional antenna would cause a problem with an omni. Just curious...

Similar Messages

HT201079 Purchase using two credit cards, different billing addresses.

I made a purchase using two credit cards, one is mine and the other is my mother's. We each have different billing addresses, but it is all under my billing address. Is there going to be a problem with the order?

For any order (free or paid), once it has been submitted and processed successfully, you may not need to worry about this order any more.
If you worry about this, wait for the receipt sent to your email address.
I don't use multiple credit card to make purchase so I cannot duplicate your issue. Sorry.

Using two Macs with differing OSs.   Password refused on one for purchases/updates

I'm running an old MacPro with OS10.5.8 and a 27" i7 iMac withOS10.9.5 which I use for working in FCPX.   The older MacPro still had FCP6 in use.    For a little while now Apple refuses to recognise my password for their store downloads and updates.    As I don't gain in any way by using these two differing OSs, is there a way to get Apple to accept my circumstances -and allow my excess to their Store and iTunes from either machine, please?

Anyone . . . ?    Please.

How can I use two sequences w/ different frame rates

I shot wedding (on Sony Z5) initially (1st tape) in DV widescreen (29.97/ 30 fps) but tapes 2, 3 & 4 were shot 1080p24 fps Big mistake; now obvious.
Edited all in FCP 6. On trying to cut & paste sequences together I get " cannot nest sequences with different editing timebases".
I have 23 min.intro/ ceremony sequence as stand alone QT mov now. How can I best convert that and/or merge it w/ the rest ( 62 min. 24 fps sequences), or perform other action to unite the diff frame rates into one, w/ best looking quality for the DVD/ bride & groom? Trying to beat Xmas deadline...
Thanks in advance! Happy Holidays to all.
3 Ghz Intel Core 2 Duo / 8 GB / OS 10.6.8 FCP 6.0.6

I went back and forth on this.
Ordinarily, I'd conform to the format that the majority of the footage was shot in. But if you're going to DVD, and it's going to be compressed to 480 anyway, then why not down convert the 1080 footage to 480?. At the same time, I would imagine re-timing the 24 (23.98?) to 29.97 would look reasonably consistent with the 29.97 SD.
This could be done in FCP, but I think Compressor will produce a better result. The adjustments you need are in the Settings menu in the Encoder (with Audio set to pass through), Geometry (720x480 16:9 Anamorphic), and Frame Controls (Resize Filter set to Best).
This will not be a short encode, so I would first test a short section to double check your settings and sound sync are right, and to compare against the quality of tape 1.
Good luck.
Russ

Can I do an Insert using two selects from different tables?

Hi,
I have three tables, Course (CID, NAME, TIME)
Teacher (TID, NAME, DESCRIPTION) and OfferedBy(CID, TID) to match a course to a teacher.
After I do an insert on Course, I want to be able to do an insert on OfferedBy using the CID of the course I inserted, and the TID of the teacher that's offering it.
I tried this after doing inserts on Course and Teacher:
INSERT INTO OfferedBy values (SELECT CID FROM Course where courseName = 'name' , SELECT TID FROM Teacher WHERE LastName = 'teacherName').
I get an ORA 00907 error.
What am I doing wrong? Can this actually be done?
Thank you
I

Hi,
How would you relate the TID with CID?
I tried this after doing inserts on Course and Teacher:
INSERT INTO OfferedBy values (SELECT CID FROM Course where courseName >= 'name' , SELECT TID FROM Teacher WHERE LastName = 'teacherName').
I get an ORA 00907 error.You can use the query in this way:
SQL> SELECT ( ( SELECT dummy FROM DUAL), (SELECT DUMMY FROM DUAL)) FROM DUAL;
SELECT ( ( SELECT dummy FROM DUAL), (SELECT DUMMY FROM DUAL)) FROM DUAL
ERROR at line 1:
ORA-00907: missing right parenthesis
SQL> SELECT 'AA',(SELECT dummy FROM DUAL) FROM DUAL;
'A (
AA X
SQL>Regards

Using Two Extremes of different generations

I have a 5th Gen AEBS (AESB-1) hooked up to a 2Wire. Then I got a 4th Gen AEBS (AESB-2) given to me and I setup it up to extend the wifi network. I need to run G too. Both running 7.6.
No possibility to run additional ethernet cable between the AEBSs.
However the 4th Gen AEBS (bridge) goes yellow, after awhile. Need to reboot AESB-2 & launch AP Utility to see it. Then turn wifi on/off to connect to AESB-2 where I can get a transmit rate greater than 130 on mac mini 2010.
If I shutdown the Mini AEBS goes yellow and wind up repeating process all over if I restart Mini.
Any suggestions to keep AESB-2 in the "green"
TIA
Devices on Network wirelessly - G5 Imac, Iphone 4 &4S, Ipad (1st gen), 2010 Mini

What is the approximate distance and the number of walls/ceilings/floors between the two AirPort? What is the basic construction material in the walls/ceilings/floors?

Using two Nike+ Nanos and one iTunes Library

Hi,
I have a Nike+ account and a nano. I am considering buying my wife a Nike+ kit to go with her nano.
We share a single iTunes library.
Can we use two nanos with different Nike+ accounts from the same iTunes account? And both upload our runs to our own accounts without confusion?

You can always setup seperate accounts on your Mac for you & your wife & place the library in /Users/Shared/ as an alternative. However, as others have posted, the settings for Nike+ are per iPod.

Two sequences with different settings?

In Premier Pro CS6, is it OK to use two sequences with different settings?

Yes, no problem.
You can make as many sequences with differents settings as you want.

Auto Setup a four channel oscilloscope using two NI 5112 boards

I have two NI 5112 boards and want to design a four channel oscilloscope supporting auto setup.
I refer to the "niScope EX Getting Started.vi". I have studied the "niScope Initialize" and "niScope Auto Setup" in the "NI SCOPE VI Reference Help".
The "niScope Auto Setup" generates no trigger output. Would it still be possible to auto setup a four channel synchronized display using two NI 5112 boards?
How can I using property nodes or by other means find out:
1. If there is a signal present on ch0 and what vertical range "niScope Auto Setup" has setup?
2. If there is a signal present on ch1 and what vertical range "niScope Auto Setup" has setup?
3. If there is no signal on a certain channel?
I
intend to use and modify the �niScope EX 5112 Synchronization.vi�

There are no NI-SCOPE functions to automatically do an autosetup on two synchronized 5112s. However, you can use niScope Auto Setup.vi on each of the 5112s individually, then reset the slave trigger parameters back to digital with the proper source. The other synch parameters (clock out/in, synch pulse, trigger out) should not be effected by the auto setup.
If the autosetup routine cannot find a signal on either channel, it will return a warning. If autosetup cannot detect a signal on a particular channel, it will set the lowest possible vertical range. To find out if there is a signal on a particular channel, take a short data set and look at it. NI-SCOPE does not provide a way to get this information any other way. If you know your signals wi
ll always produce a range greater than the smallest range of the 5112, you can use the vertical range as the way of telling that no signal was detected.
You can query almost any current parameter from the driver using property nodes. The vertical range is channel specific, so first set the Active Channel, then query for Vertical->Vertical Range. A word of warning when querying parameters. NI-SCOPE is IVI compliant, so the values you get from querying the property nodes are based on the IVI specification, not the NI-SCOPE LabVIEW API. Sources will always be strings and some properties have the same format, but different mappings. For example, the trigger slope in the LabVIEW API is mapped 0-positive, 1-negative. If queried from the property node, 0 is negative and 1 is positive due to the IVI spec. There are not many of these. You can easily find them by looking in the block diagram of the set VIs for look-up tables (array constants).
Good luck! If you
still need more help, post a reply
This account is no longer active. Contact ShadesOfGray for current posts and information.

How can I send email using two different email address that both link back to my one exchange account on my Ipad mini

How can I send email using two different email address that both link back to my one exchange account on my Ipad mini?
On my PC I simply have a master return email address and use a POP for the secondary address. Both are through the one exchange account without a problem. I need to be able to do the same on my Ipad.

Ah, I should have made that clear. My domain didn't come from google. It was purchased at and is hosted at dreamhost, but I haven't used their email servers in years - I just route everything through gmail. I actually have a bunch of domains (with websites).
Gmail has an option that lets someone with custom domains send (and receive) email through gmail using the custom domain once Google confirms proper ownership of the domain (to prevent spammers and such). Gmail has a setting for "send email as" which allows gmail to be sent using a custom domain as the sender. I'm pretty sure Apple's old mobileme had this feature too, but I didn't use it.

Using two facts of two different star schemas and conformed dimensions

Hi,
I've been working as developer and database designer for years and I'm new to Business Objects. Some people says you can not use two facts of two different star schemas in the same query because of conformed dimensions and loop problems in BO.
For example I have a CUSTOMER_SALE_fACT table containing customer_id and date_id as FK, and some other business metrics about sales. And there is another fact table CUSTOMER_CAMPAIGN_FACT which also contains customer_id and date_id as FK, and some other business metrics about customer campaigns. SO I have two stars like below:
DIM_TIME -- SALE_FACT -- DIM_CUSTOMER
DIM_TIME -- CAMPAIGN_FACT -- DIM_CUSTOMER
Business metrics are loaded into fact tables and facts can be used together along conformed dimensions . This is one of the fundamentals of the dimensional modeling. Is it really impossible to use SALE_FACT and CAMPAIGN_FACT together? If the answer is No, what is the solution?
Saying "you cannot do that because of loops" is very interesting.
Thank you..

When you join two facts together with a common dimension you have created what is called a "chasm trap" which leads to invalid results because of the way SQL is processed. The query rows are first retrieved and then aggregated. Since sales fact and campaign fact have no direct relationship, the rows coming from either side can end up as a product join.
Suppose a customer has 3 sales fact rows and 2 campaign fact rows. The result set will have six rows before any aggregation is performed. That would mean that sales measures are doubled and campaign measures are tripled.
You can report on them together, using multiple SQL passes, but you can't query them together. Does that distinction make sense?

I have two users with different music on each itunes and i can only use one library, how do i use both for one iTouch?

i have two users with different music on each itunes and i can only use one library, how do i use both for one iTouch?

Chris, I believe this link may have the information you're looking for. Welcome to discussions!
http://docs.info.apple.com/article.html?artnum=300432

Use two different printer services in one web template?

Hi!
Is it possible to use two different help services for printing in the same web template (for the same table item)?
Print1:
<param name="HELP_SERVICE" value="HELP_SERVICE_PRINT"/>
<param name="HELP_SERVICE_CLASS" value="ZCL_RSR_XLS_HELP_WINDOW_PRINT"/>
Print 2:
<param name="HELP_SERVICE" value="ZPRINTING"/>
<param name="HELP_SERVICE_CLASS" value="ZBW_PRINT_HELP_SERVICE"/>
I was thinking that you maybe could change the param name values for the "Help_service" and the "help_service_class" at runtime using the properties for the table item, so that you could choose which one to use, but I havne't been able to do that so far.
Does anyone have an idea?

This is not a problem. Just put the print service for the print to excel on an object other than the table web item. As long as these print services exist on any web item, you should be able to invoke them. I've tested this with putting the "Print with Excel" service on the Navigation Block Web Item and the other print service on the table web item. Hope that helps!
Prakash

How to use two different network cards on RT?

Hi everyone... I'm currently working on a project where I have to deal with the issue mentioned in the thread's topic: I have a PC with RT LabVIEW that has to be able to establish network connections using two different network cards. One will be used to connect via TCP/IP with a host computer that will show the data transmitted through shared variables; the other will communicate with another PC through Modbus protocol. The key is that each communication is done through a separate network card.
So far I haven't been able to figure out how to configure both things to happen. Does anyone know how to do this? Any tips will help.
For the RT communication I'm using a standard RT project, with the RT PC being given one of the IPs, and for the Modbus part, I created an I/O server with a master and a slave. Separately everything works fine, but when I get them together it simply won't work.
Thanks for your help!
Solved!
Go to Solution.

Sorry it took me so long to answer, I've been busy lately....I've found a solution to the problem I mentioned, and just in case anyone has similar problems in the future, I'll shortly describe what happened.
As Caseyw suggested, it was necessary to enable both network cards through the Measurement and Automation Explorer. The cause of the connections malfunction was actually that I wasn't using the "right" protocol for the Modbus communication, which ran on the secondary adapter. The solution was to use the URL protocol with the correct path on the field, addressing the right IP address. To avoid making this post a mixture of topics, I won't elaborate futher, but I got the gist of it, so if anyone is having similar problems whether it is working with several network cards or with Modbus communication protocols, feel free to contact me, I'll be glad to help.
Thanks

How to use two different versions of Firefox at the same time on Snow Leopard?

I recently upgraded to Firefox 4.0 on my 27" iMac running Snow Leopard 10.6.7.
Previously, I was using Google's "Page Speed" along with Firebug in Firefox 3.6.15 to optimize images in my web pages, and to find other areas to optimize.
Page Speed is not yet compatible with Firefox 4.0. I wrote to Google about this some time ago -- no answer yet.
If I run Firefox 3.6.15 in order to use Page Speed, I run into a few problems afterward when I start using Firefox 4.0 again, since they both use the same "Firefox" folder in my "Application Support" folder.
How can I set it up so that I can have two separate "Firefox" folders in my "Application Support" folder?
Or is there an easier way to use two different versions of Firefox simultaneously, even if one has extensions and/or plug-ins installed which are not compatible with the other version?
Thanks for a great browser!

Please disregard my question. I just conducted more web search and learned how to use Firefox's profile manager in order to make a separate profile for Firefox 3.6.15.
You can find instructions on this page:
http://support.mozilla.com/en-US/kb/Managing%20profiles#os=mac&browser=fx35
'''A small tip:'''
If your Firefox app is named anything other than "Firefox" -- say for example "Firefox 3.6.15" -- when you follow the instructions at the above link, make sure you escape the blank space that is before the version number by adding a backward slash before it, when you type the command string in the Terminal. In other words, in that string, you should use this:
Firefox\ 3.6.15
I hope that helps someone.
WW

Using two or four different antennas on a 1242AG

Similar Messages

Maybe you are looking for