Using video sender with Youview box

I have just set up my new youview box.
With my previous BT box I was able to use a nikkai video sender so I could control and watch the TV/box in another room.
This doesn't seem to work with this new box. Is is incompatible for some reason?
Is that I just haven't put the "receiver" widget near enough to the infra red on the box.
Greatful for any help! Thanks

Hi Poynders,
Thanks for posting. Take a look at YouView screens not visible over AV / video sender . It’s an older thread but might help. Let us know how you get on.
Cheers
David
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

Similar Messages

How to use video conference with life messenger, how to use video conference with life messenger

how to use video conference with life messenger, how to use video conference with msn life messenger

Hi,
Do you mean Window Live Messenger or it's Mac equivalent MSN for Mac ?
Actually the app comes with Office
In the Microsoft Office X (2001 version) it was still called MSN Messenger
In Office 2008 it was called Microsoft Messenger.
The current one that can also be downloaded as a standalone app also comes with Office 2011 is also called Microsoft Messenger.
This is version 8 and this version is the only one that can Video Chat as a standalone app.
Version 7 required you were in a mixed environment (with PCs) connected to the correct sort of Windows Server.
This page may help you further.
8:20 PM Saturday; June 11, 2011
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb( 10.6.7)
 Mac OS X (10.6.7),
"Limit the Logs to the Bits above Binary Images."  No, Seriously.

Using video clips with my ipod

I am working on a project that requires me to use video clips on my ipod(I have a video ipod). I would like to divide each clip(about 10-20 seconds each) into approximately 10 categories. There would be about 100-200 clips in all. I would like to be able to view these clips on my ipod and that they be organized on my ipod into these 10 categories for easy browsing. The categories and the clips would ideally all have names attached to them. My question is: Is this possible, if it is, how do I go about doing this?
Any help would be greatly appreciated.
Thanks

Well that would explain why you cannot add them to your Nano.
Try using a program such as Handbrake or MPEG-Streamclip to convert these clips to more friendly formats. I have had the best results with these two utilties.
B-rock

Using owa_cookie.send with JSPs

Hello all... I have a procedure that I use owa_cookie.send to send a cookie in the HTTP header. How do I get it from a JSP now? If I include this cookie in my xxx.home procedure, do I need to do anything special to be able to get it when I navigate to my JSP?
Thank you all in advance.
Jonathan Coreil

-- GET_ALL returns an array of name/value pairs of all HTTP_COOKIES
-- sent from the browser. The name/value pairs appear in the order
-- that they were sent from the browser.
PROCEDURE owa_cookie.get_all
(names OUT vc_arr,
vals OUT vc_arr,
num_vals OUT INTEGER);
the number of vals is > 0 if the cookie is stored at the clients side. I implement it just.
I quest the number of cookies
if l_NumVals = 0 then
Send cookie;
redirect_URL('...');
else
get_Cookie_Content;
end if;
It may not help you. Please specify your problem if possible.
Regards Torsten

Using Video Adapter with eMac

I've searched all over and cannot find any information on this, so any help would be greatly appreciated.
I would like to send video from my eMac to my TV. I purchased the Apple Video Adapter and an RCA cable. I have the adapter plugged into the computer, and the cable plugged into the adapter and the TV. I restarted the computer. The TV (on its video setting) shows static with the adapter plugged in; if I take it out, it goes black, so clearly some signal is passing through. However, I cannot figure out how to get the eMac to recognize the new "display".
The discussions on the subject mention using a "detect display" fuction. I don't see anything called "detect display" in the display preferences. I do have it set to show the displays in the menu bar, and the drop-down menu only shows the eMac and its resolutions. The preferences, also, only gives me the info for the eMac.
Am I missing something? Is there a setting I need to change? Should I assume the adapter is defective (I gather this has happened to others)?
Thanks in advance for your help!
eMac 700 MHz Mac OS X (10.4.3)

I don't think the problem is at the TV's end, as it's clearly getting some sort of signal on the video setting I'm using (there's static when it's connected to the computer, and nothing when it's not). The problem is that the computer doesn't see that it's connected to another display.
Something I realized, comparing computers (we also have a Mini)--the Mini's display preferences window has a "detect displays" button that the eMac's doesn't. They're both running 10.4.3. Any ideas (anyone?) why the eMac's missing it?
Thanks again!

Using screen reader with check boxes.

Hello All,
I have a check box on a form. Upon tabbing to the check box the custom text is read by the screen reader. The custom text provides an explanation of the field as well as the current state (unchecked). Is there a way to have the screen reader announce the state of the check box upon changing from unchecked to checked?
If this required scripting or the use of alternate text, an example or explanation would be greatly appreciated.
Thanks,
Jelf12

Jelf12,
You should be careful about providing too much information in the CSRT, I usually recommend that people just rely on the caption text for checkboxes -- if the information is sufficient for sighted users, then in combination with the information provided to the assistive technology via our accessibility API in Adobe Reader the information should be sufficient for non-sighted users.
For example, if you have a checkbox that has a caption that is "Please send me information about new offers", that would be fine for screen reader users because when they land on the checkbox they will hear "please send me information about new offers, checkbox checked" and if they uncheck it (you can assume that how to toggle a checkbox is common knowledge so don't need to convey this information) they will hear "Unchecked". If the user tabs away and tabs back they will hear the full explanation again, except with the changed state reported.
It is tempting to overdo it, but for most checkboxes all you need to do is make sure that the screen reader precedence is set to "Caption" and move on.
AWK

Using Video CAMERA with Connect pro

We reciently purchased this product and were told that it
would work with video cameras. We have a Panasonic that we are
using with vista. this camera works with Premiere Pro, and there is
nothing wrong with it. I know that Connect is not software based it
is an Internet Application. How ever i know that the OS (vista)
"sees" the camera because it works with other programs. Sorry i am
connecting with IEEE not USB
Has anyone out there in the world has success with getting a
video camera using IEEE connection to work fully. Audio and Video
coming through the camera?
Is anyon aware of drivers for either the camera or the IEEE?
And if the Connect product does not support this... WTF?
thanks

Connect does work with IEEE1394 Firewire Cams, just not with
all Firewire Cams. (USB cams also are not all working).
I would suggest to first try out the cam from different
machines with different OSs (Vista might well be the sole issue
here), also try if you can get an ordinary USB cam to work.
If all fails, you can workaround that using a virtual camera
driver, piping the firewire cam into the virtual cam and in Connect
you can load the virtual cam with the image of the Firewire cam.
Not a nice way round, but it would work.
If you google for "Adobe Connect camera compatibility matrix"
you get a "slightly" outdated list of supported cameras.

Blurry Text When Using Video out With FX 5900U

I just got a MSI Geforce FX5900Ultra VTD256, and i was trying to play games on my TV. I used the S-Video to video (the yellow Cable) adapter and when im in the desktop, all the text is real blurry, i cant even read it. I tried lowering the resolution to see if that would make it easyer to read, but it didnt work. Can someone please help. Maybe the is somthing wronge with me TV???

Hi,
TV sets have lower resolution and bandwidth than PC monitors - the two are sort of related, but are not quite the same thing.
Resolution is often measured in "lines", meaning the number of individual vertical lines that could be displayed across the width of the TV and still be distinguishable as individual lines. A figure of 800 lines was considered pretty good, and could usually only be achieved in a TV studio, from a camera direct to a monitor. So 800 pixels is about as much as a TV (especially a smaller one) can reasonably display. (The vertical resolution depends on the TV standard, and is about 600 lines or pixels for PAL, and about 500 for NTSC)
The other factor is Bandwidth, which is measured in Megahertz (MHz). Basically, the finer the (horizontal) detail, the more bandwidth you need in the path between the source and the picture tube to display it faithfully. Broadcast TV is deliberately limited to about 5MHz, whereas a computer monitor will have several tens of MHz of bandwidth.
Also, the chrominance (colour) component of a composite or S-Video signal is limited to less than 2 MHz, so fine colour detail will be worse off (Black on white or vice-versa will give best results).
Anyway, the practical outcome of all this is that the highest resolution you can use for TV out is 800x600, and even then you need to use larger fonts (so the vertical lines are thicker, and there are a reasonable number of horizontal lines in a character). The maximum number of characters per line should be less than 60-80.
There are some scan-converters available which use fancy techniques to render a reasonable image at higher resolutions, but they are fairly expensive.
S-Video should give better results than composite, but you will still be up against bandwidth and resolution limits
Cheers

Using video splitter with Bootcamp?

I need to set up a Mac mini in my school by connecting it to a monitor and projector simultaneously, so I connect the video port to a VGA Splitter box. However it is found that nothing can be displayed on the projector through the splitter box while on the boot volume selection screen and inside Windows. The problem occurs even at the boot volume selection screen before choosing Windows, so it's not a Windows display driver problem. The same problem can be found on newer MBP and iMacs.
Is there any solution to this problem? Thanks in advance.

I'm not trying to have two different resolutions, just mirror the main display on the projector. I've tried the TB -> VGA adapter but it doesn't work either.
But my colleagues found an alternative: using the HDMI output and adding a HDMI to VGA adapter. It seems to work in our initial tests.

Using Video advantage with IP Communicator on CME 4.0

I am having issues getting video advantage to work with IP communicator. I am using VA 2.0.2.0 and IPC 2.0.2.0 and CME 4.0. I added the commands
voice service voip
h323
call start slow
telephony-service
service phone videoCapability 1
call-park system redirect
create cnf-files
and added the video command under the ephone. If you have any suggestions I would appreciate it.
Thanks,
Andrew

Paal
I am not using Call Manager. I am using Call Manager Express. There is no version 4.1 the documentation says that it should work with 4.0. that is the latest version of CME. Do you have any insight on this.
Thanks,
Andrew

Using Video IChat with Lid Closed

Using an Apple Cinema Display with my MacBook Pro, external keyboard etc. I Close the lid, attach a USB Camera (logitech Notebook Camera) fire up IChat and am told the camera is in use by another application. Can you have two cameras (internal and external) with a MacBook. I note that even with the cover open, it does not recognize the Logitech camera. I have installed macam 0.9.1
MacBook Pro Mac OS X (10.4.9) 2GB Memory

Hi Csjohn,
Is this a UVC (USB Video Class) camera ?
If not it will also need http://www.ecamm.com/mac/ichatusbcam/
9:15 PM Saturday; April 28, 2007

Can I work use videos made with 24fps for the IMovie App?

Hallo,
I was making a video with my iphone 4s and the App Filmic Pro. I choiced 24fps. Can I use this film for I Movie or only films on 30fps?

In IBooks Author choose Share:Export... iBook. Drag the YourBook.ibooks file onto iTunes, maybe directly into the Books panel. Sync your iPad with the Mac, selecting YourBook in iTunes.

Using video clip with an alfa channel??

Hello. Like I wrote above, I have a video with scrolling text that is sitting in a drop zone. It looks fine in the menu editor but when I simulate the menu(s) they have a black background instead of the transparency.
Can anyone offer some advice on how I can keep the alfa channel video?
Thanks for your time.
Cheers,
Christopher

Weirdness!! I just noticed that some buttons were overlapping the drop zone so I changed the size, saved and simulated again and voila!! working fine. I thought it might be the problem.
Hmmm...
Have a good day all!

How to use Application Designer with virtual box vm's

hi all,
I could use some help please.
I have everthing installed and working on the VMs but now I want to use Application Designer but I must be doing something wrong.
I installed the Oracle client on windows and created tnsnames.ora. I can't connect to the database from windows to vm.
I have some questions which might help me fix this.
The directory that was mentioned to put tnsnames.ora in (C:\app\Mike\product\11.2.0\client_1\network\admin\) was not there so I had to create it. Was that what I was supposed to do or did the install go bad?
For the windows host file what should the ip addresses be? I used the IP Addresses of the eth1 network interface from both guests which I created.
As far as the PeopleTools on windows I used PT 8.52 but with no patch will that work even though the VMs are PT 8.52.06? So if I need the patch in order for App Designer to work how can I get the patch I think I need an account to do that. I think it mentions in the OVM doc that they are included somewhere so should I use those instead?

<strike>With virtualbox vm's I assume that you mean the OVM templates converted to virtualbox.</strike>
Didn't notice the OVM category :)
Which Oracle Client installer did your use?
You could use the following download from MOS for Database 11.2..02 (since Peoplesoft database is also delivered at 11.2.0.2)
Patch 10098816: 11.2.0.2.0 PATCH SET FOR ORACLE DATABASE SERVER
From the patch set download only p10098816_112020_platform_4of7.zip, which is your database client. The rest you will not need to be able to use Application Designer and Datamover.
Once downloaded start the installer and choose option Runtime (do not choose Instant Client or Administrator).
Now that you have your connectivity, you can start the PIA-AppBatch vm.
switch to psadm2 user and go to $PS_HOME.
Here you will find two files
toolsclient.zip (PeopleTools 8.52, use client only)
toolspatchvcd.zip (PeopleTools patch 8.52.06, , use client only)
Copy these files to your windows workstation and install them in that order.
Copy the tnsnames from the Database vm to your oracle client install dir network\admin dir and you should be ready to start using Application Designer/Datamover.
For more detailed information see the post from Nicolas:
http://gasparotto.blogspot.nl/2012/09/psovm-fscm-91-feature-pack-2.html
http://gasparotto.blogspot.nl/2011/10/peopletools-852-client-installation.html
Regards,
Hakan
Edited by: Hakan Biroglu on Mar 9, 2013 1:23 PM
Edited by: Hakan Biroglu on Mar 9, 2013 1:30 PM

I can not use adobe send with my acrobat pro how come?

I just bought acrobat send and want to send an acrobat pro file but it keep referring back to page to buy the product which I already did.
NursePro

There is a solution (I'm running Snow Leopard on a Core2Duo iMac, but this problem arose when I was running Leopard on a G4 PowerBook too).
Problem:
You download the OS X driver for the scanner from Canon's site. I already had the CanoScan Toolbox (4.1) stored on an external drive.
You unzip the driver and run the VISE installer. After a search it finds your copy of Photoshop (and maybe even the CanoScan Toolbox), and you click to install on that/those location(s).
You get a couple of error messages, which you click through.
You restart your computer and try to run the scanner but you get an error that the driver is wrong or missing and the process will abort.
Solution:
BEFORE you restart, and with the installer package still open -
1. Copy the Into_CFMSupport_Login & Into_CMPrefs folders to
Applications : Canon Utilities
Applications : Canoscan Toolbox
and remove the prefix Into_ from each folder
2. Check whether the installer placed N067U_Library.shlb into the top level (not User level)
Library : CFMSupport
and if it didn't, move it there yourself
THEN restart, and try again. It worked for me (via Photoshop), but whether it will work for everyone, I don't know.

Using video sender with Youview box

Similar Messages

Maybe you are looking for