Using WRT610N router with Westell 327W modem/router on Centurytel

I have DSL with Centurytel and have a Westell 327W modem/router installed. Can I install and use a WRT610N router with this setup to get a faster wireless connection?

Both the wireless router can work together...You need to cascade both the router.

Similar Messages

Verizon DSL, Westell 6100 modem/router, and Airport Extreme

Useful info so you won't have to go through what I did.
Verizon ISP using the Westell 6100 modem/router & Airport Extreme.
The Westell 6100 was configured during installation as a modem and router with a direct connection to the Mac. You can actually connect Airport Extreme at this point with an ethernet connection to the Westell and it will work, but you can't do any of the sharing things (remote login, personal web sharing, etc.) To do those things the Westell needs to be in the Bridge mode. In a nutshell, you have to edit the Westell's VC configuration to establish Bridge mode, and disable its DHCP server. Then you have to set up the Airport to connect using PPPoE using the Account Name and Password from Verizon.
1. With the Westell connected directly to the Mac, access the device at 192.168.1.1.
a. Under VC Configuration the first of seven configurations should already be enabled as VPI 0, VCI 35 using PPPoE. Edit that one and change it to Bridge mode.
b. Under DHCP configuration, disable the DHCP server. You can also do this under the Private LAN Configuration page. If at the latter, do not attempt to disable the Private LAN (it won't let you anyway). Verizon tech support kept insisting I had to disable the Private LAN, which caused a great amount of anguish!
c. Before leaving 192.168.1.1 (you won't be able to access it again once the Airport is connected and configured) make sure you know your ISP account name and password. This was assigned during my setup procedure with Verizon, a random selection of letters and numbers.
2. Now hook up the Airport WAN to the Westell's ethernet port and the Mac to the Airport LAN. Fire up Airport Admin Utility.
a. Under the Internet tab, select Connect Using PPPoE.
b. Configure PPPoE using the Verizon Account Name.
c. Change password to the Verizon account password.
3. Restart and that's it.

Thank you for your post. When I moved to another home, Verizon sent me the Westell 6100 and I had been having trouble staying connected to the Internet with my Airport. Last night, I loss wireless access and the Airport status in the menu bar read "Looking for a PPPoE connection". Verizon customer support was able to get me back online, albeit with only a direct Ethernet connection between my iBook and the 6100.
I found your post and followed your instructions. Now all the iBooks in our household are back online via the Airport. Thank you very much!
iBook G4 933Mhz Mac OS X (10.4.7)

Is Westell 327W modem supported by Verizon?

I purchased Westell 327W modem - it does not work with my DSL line. I connected it through a cable to my laptop - no internet. Other modem is working, so the is no problem with dsl line.
Tech support told me this modem is not supported, but I saw some messages of people who use this modem.
Thanks,
Zalek

The Westell 327w is supported, but is considered Obselete by Verizon. Just make sure the problem with the Westell 327w isn't because the Westell is in bridge mode, the Westell has the wrong PPPoE information, or you're in a DHCP Area and need to allow your connection a few hours for the lease on the IP address to expire.
Check the settings of your working modem and see if you can match them as close as possible to the Westell 327w. If you have to, factory reset the 327w using the pinhole in the back. From this point, if the 327w is a Verizon modem, once the modem auto-detects the correct settings for the line you will need to disable the walled garden at http://192.168.1.1/verizon/redirect.htm .
If you need more info on any of this, just ask.
========
The first to bring me 1Gbps Fiber for $30/m wins!

I recently replaced my dead airport router with a netgear91-5g router and synced it successfully to my Lexmark Pro 915 printer and my computer and yet when I try to print wirelessly I get the message: "printer not connected; printer offline".

I recently replaced my dead airport router with a Netgear91-5g router and synced it successfully to my Lexmark Pro 915 printer and my computer; yet when I try to print wirelessly I get the message: "printer not connected; printer offline". Lexmark support verified that my printer was connected to the new router and the problem was with the computer's printer configuration and they could reconfigure it online if I paid for their "Premium Support" services ($119 for one year, 3 fixes). I declined, feeling sure that this is something I could do if I knew how. Could it be an incompatability issue with OS 10.8.3?

You saved me $$$ that I can ill afford on my fixed income. I was very unhappy with the "support" from Lexmark... what a rip off! Thank you dwb!

Linksys router no longer works with Westell 6100 modem

Hi all,
I came back after a 3 month work absence (and many days power outages, according to the neighbors), to find that my system can no longer connect to the internet using the Verizon Westell 6100 modem to a Linksys wrt54G router to 2 PCs!
I reset the Westell modem and directly connected the PC to it and THAT works okay, but put the router back in the mix (so I can connect my other PC) and nothing works!
I have read on this forum about 'Bridgeing" the Westell modem but nothing about setting up the router.
Can someone PLEASE give me explicit instructions on how to:
    1.) set up the Westell modem in this "Bridge" mode,
    2.) Set up the Linksys router to work with the modem again??
    3.) Tell me why the old setup no longer works, did verizon change something for this modem?
Thank you VERY much for your help in this matter!
SUE ;>)

the router has two connections. one is called a WAN and that is a wide area network, and it means the internet in your case. and one is called a LAN, local area network.
what you saw means - that the way you connect to your internet is through PPPoE, a username and a password.
and then way your LAN connects is DHCP, how all of your local computers connect. This is important, because after you bridge the westell, you will be setting your Linksys up for PPPoE connection, and NOT DHCP. if you don't do this step, then you will never connect.
that is fine, and normal. if you follow the instructions at the link provided - you will be able to connect real easily.
you will want to bridge the westell just follow the instructions for "If your Westell uses the red and black Verizon firmware:"

I am FRUSTRATED! My goal is to create a wireless network using an iMac, a Westell 2100 modem (and router)

I started with a PC, the Westell 2100 modem (also a router) and the Linksys WRT54G. I set it up according to instructions I found on the Internet, and it worked fine for YEARS!!! Then, I switched to an iMac. After problems with the setup, I found help on the Internet, and got it working. It has been a long time since then, and I have had to disconnect things, and I do not remember how to set it up. I have searched the Internet, but cannot find a solution. I have searched the community, and followed some instructions here, but I have had no success. I know the following:
The Westell 2100 works as it should. I can connect directly to my computer and access the Internet.
The Linksys WRT54G has not been damaged.
At one point, I had set the SSID and had a WEP/WAP key that is HIDEOUSLY long. Here are some more tidbits: WPAPSK TKIP.
Please help! My new iPhone 4S(teve) needs it's wireless connection to Wi-Fi .

Pleeeze help???

Connecting my WRT610N with my other Modem\Router (Philips ADSL Modem\Router)

Hi, I recently purchased a WRT610N Dual Band router and I have some questions to ask. I plugged the UTP cable (blue one) from my modem's\router's (Philips) ethernet port 4 to "Internet" port of the WRT610N router. In "Basic" Setup I chose "PPPoE Connection" (my ISP here in Greece working in PPPoE) and everything gone fine. WRT610N seems to log to Internet and everything is OK....but... In those 2-3 days that I'm working on it, I am curious in How this works.. and if my setup is 100% ok because I one bizzare problem.. the problem is that I run a DynDNS.com Client application, cause I wanna have Remote access from my work. this client has logs, I reviewed the log and I see that every 10 or 20 minutes (exactly 10 or exactly 20) my IP is different.. (I use dynamic IP from my ISP)...and I ask : What I have to do to the MODEM\ROUTER from one side and WRT610N on the other side? What setup? What exactly I must do to be 100% sure that everything is working fine? NAT ? firewalls from the two routers? DHCP ? In general I mean... Thanks and.. sorry for my English.. (I'm from Greece so.. )
Life Is Painless.. (for the brainless)

Forget it and.. SORRY.. (If a moderator can delete this thread..please do it..) I found the right answer in this thread :
http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&message.id=26177
Life Is Painless.. (for the brainless)

Using Airport Extreme (802.11n) with Netgear Wireless Modem Router

I have a quick question, can I use the Airport Extreme in a wireless modem router?(http://www.netgear.co.uk/wirelessadslrouterdg834g.php)
By plugging the Airport into the Netgear router would I be able to by pass and run a network this way. I have a 802.11n enabled MacBook and Apple TV, the Netgear is the weakest link!!!
Many thanks.

neptune2000's post was implying that you connect the AirPort Extreme base station (AEBS) to the Netgear.
The AEBS does NOT contain a modem. Therefore you will need a modem, either the Netgear or another.

WRT54G & Westell DSL Modem/Router

I want to use the WRT54G as a WAP or signal repeater to extend the range of my Westell 327W DSL modem/wireless router. Is there a way to do that? I'd like to put it halfway between my wireless router and another wireless computer in my house.
Message Edited by rweintra on 08-08-2007 05:13 AM

That router can not be used as a repeater. You can turn it into a wireless access point but it will not repeat the signal from another wireless router with the linksys firmware. You can try to look for a third party firmware that may give you that option but if you do install a third party firmware it will void any warrenty you have on that router.
Check this LINK for other firmware.
Richard Aichner (Ikester)

Do you have to set up AE inBridge mode with existing wireless modem router?

Hi
I've just bought the AE and Apple TV. My plan was to basically use my existing Netgear wireless modem router for the internet only and set up the AE as the wireless router. I also bought the AE to boost the strength, print wirelessly and I thought it might work better with the Apple TV. The other things I use on my home network are ipad, iphone 4, HP DV6 Notebook, Toshiba Notebook and PS3.
I've plugged the Netgear into the AE with an Ethernet cable. I initially started with the "replace existing access point with AE", as I thought I was replacing the Netgear with the AE. This option left me with internet working and a blinking amber light on the AE.
I then did a hard reset and started again. I diabled the wireless on my old modem/router and chose the "create wireless network" option in airport utility. I think it worked because I have internet and a green light but to be honest I have no idea what I did. I know it's in bridge mode but only because I didn't know how to set up the other options.
Also, I've ended up with three networks out of this process. The default network for the AE (but it has one of those yellow error icons next to it in the available network list), the one I set up and a 5ghz of the one I set up. Neither the default network of the 5ghz network show up in the Internet and Networking control panel, which is where I delete them. I just thought this was odd.
What I'd like to know:
Do you have to set it up in bridge mode when you have an existing wireless modem/router?
If not, is there any benefit to setting the AE up as the router instead of using the Netgear?
If I create a new network should the default network still be showing up in my list of available networks or have I done something wrong?
If I have a 5ghz network, does that mean that the other network I created is only 2.4ghz or is it still dual band?
Considering the devices I have would it be beneficial for me to have a 5ghz network for certain devices only like the Apple TV?
As you can probably tell I have no idea what I am doing. I'm basically just clicking stuff and seeing if it works.
Any help/advice is much appreciated
Thanks
Jo

Hello Jo Sugden. Welcome to the Apple Discussions!
Do you have to set it up in bridge mode when you have an existing wireless modem/router?
You don't have to but, most likely, it will be the best configuration choice when you have the 802.11n AirPort Extreme Base Station (AEBSn) connected to your main Internet router by Ethernet. In this configuration, all NAT & DHCP services will continue to be provided by the Netgear router. This will allow all wired or wireless clients connected to the AEBSn to get their IP address (and be on the same subnet) from the Netgear ... and this would allow clients connected to either router to "see" each other.
If not, is there any benefit to setting the AE up as the router instead of using the Netgear?
If, for some reason, you wanted to create a separate subnet, configuring the AEBSn as a router would allow for this.
If I create a new network should the default network still be showing up in my list of available networks or have I done something wrong?
By default, your AEBSn will create two wireless networks with the same Network Name; one broadcasting in the 5 GHz band, and the other in the 2.4 GHz band. The default name for both of these will be Apple Network NNNNNN. You have the option, within the AirPort Utility, to change the names of each network.
When connected by Ethernet, and in bridge mode, it would be beneficial to name your AEBSn's networks the same as that provided by the Netgear. This would create what is called a "roaming" network ... where you literally can roam with a laptop from one router to the other and still be on the "same" network. This also is a way to extend the wireless range of the Netgear.
If I have a 5ghz network, does that mean that the other network I created is only 2.4ghz or is it still dual band?
As a minimum, you will have three wireless networks: one provided by the Netgear and two provided by the AEBSn. By giving them all the same Network Name, they will appear as one to any wireless client. However, they will all show up in a utility like iStumbler or AirRadar.
Considering the devices I have would it be beneficial for me to have a 5ghz network for certain devices only like the Apple TV?
Yes. Operating a wireless network in the 802.11n Radio Mode in the 5 GHz Radio Band offers the best potential bandwidth ... around 300+ Mbps. The only real drawback of the higher frequency band is that the signal strength drops off more rapidly with distance than in the lower frequency band. Also higher frequencies cannot penetrate objects (like walls) as well.
Ideally, you would want to place your Apple TV or other streaming devices in the same room as the 5 GHz network ... or connect them to the router by Ethernet.

AX as client with third party modem/router

Like others, I'm having trouble getting my AX to join an existing network from my third party modem/router (in this case a Siemens SE 515 dsl). After 2 days of sifting posts, changing settings and reset after reset, I'm about to take the thing back or just toss it out the window. I really only want to use the AX for AirTunes but do want to be able to surf at the same time.
My modem/router is set as PPPoE with login details and PPPoE pass-through is enabled, as is NAT. The modem is set to get IP address automatically. WEP-128 is on and I've activated MAC access control (and am sure it's the correct id for the Airport). It's set for DHCP in the range 192.168.1.xx. WDS is activated and the router detects other devices around the place.
In Network settings on my Powerbook I've selected PPPoE and also entered the login details here. In the TCP/IP tab, IPv4 is automatically set to PPP and the computer gets an IP address but it's in 84.xxx... range. Internet access works fine when I use these settings.
Now, reset the AX, in Airport Admin I set it to client (I don't need to extend the network), entered the WEP key and selected the router network name from the pop-up menu. In the Internet tab I select DHCP, in music tab AirTunes is on and I've entered a speaker name. Click update, then...
Nothing happens.
Well, not quite. The orange light on the AX is flashing. When I go into iTunes, the Airport is listed in the pop-up at bottom right but when I select it, iTunes says it is trying to connect and, after a while, fails. Airport Admin can no longer find the AX either.
My hunch is that this is something to do with IP addresses but I really have no idea. Any hints gratefully received.

1. your modem/router should not have "PPPoE pass-through" enabled. The PPPoE connection with your ISP must be handled by the modem/router itself - not by your Mac. The modem/router should be functioning as a NAT router, and all the wireless clients (like your Mac and the Airport Express) of the modem/router should be connecting to it using DHCP.
2. I don't know why you activated WDS on the modem/router. It isn't necessary, and whatever WDS flavor is supported by this modem/router won't be supported by the Airport Express. Turn it off.
3. On the Powerbook, in System Preferences->Network->Show Airport - (a) under the PPPoE tab the box to "connect using PPPoE should NOT be checked and (b) under the TCP/IP tab the only selection should be to configure using DHCP.
Before proceeding to the next steps, you must now make sure your Mac is still able to access the internet wirelessly.
4. Do a factory default reset of the Airport Express. Temporarily switch wireless network connections on the Mac from your modem/router to that of the Airport Express. Run the Airport Admin Utility. In the Airport Admin Utility, select the mode to be "join an existing wireless network". Below that, type in the SSID of your modem/router. Enter the same WEP type and WEP key as used on your modem/router. Make any other configuration changes required under the Music tab, then update settings to the Airport Express. When finished, switch the wireless network connection on the Mac back to that of your modem/router.
5. If you still have trouble, remove all security (MAC address filtering and WEP) from your modem/router and see if you can then get the Airport Express to connect as a client.

877 using fe as WAN (ISP provider modem/router) - VPN won't come up!

Hi,
Due some changes with our ISP, the atm interface on the 877 router won't support stable connections anymore. The fix I'm having to do is to use our ISP provided modem/router, and have the 877 use an fe port as a WAN port and instigate the VPN from there.
I've had issues with getting the WAN port to work correctly that I got fixed here:
https://supportforums.cisco.com/message/4090973
Now I've got to get this bit going then I'm all good!
Basic set up is:
Remote firewall <-> internet <-> local ISP (modem/router) <-> Cisco 877 <-> laptop/switch etc
172.20.0.0/16                             192.168.1.254       192.168.1.139    172.30.99.1     172.30.99.0/24
Current config is:
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug uptime
service timestamps log uptime
service password-encryption
hostname ITTEST
boot-start-marker
boot system flash:c870-advipservicesk9-mz.124-24.T6.bin
boot-end-marker
logging message-counter syslog
logging buffered 10240
enable secret
enable password
no aaa new-model
clock timezone GMT 0
clock summer-time BST recurring last Sun Mar 1:00 last Sun Oct 2:00
dot11 syslog
no ip source-route
ip dhcp excluded-address 172.30.99.1 172.30.99.100
ip dhcp pool dhcppool
   import all
   network 172.30.99.0 255.255.255.0
   default-router 172.30.99.1
   dns-server 172.30.99.1 172.20.0.120 172.20.0.121
   domain-name gratte.com
   update arp
ip cef
ip domain name gratte.com
ip name-server 192.168.1.254
ip name-server 172.20.0.120
ip name-server 172.20.0.121
no ipv6 cef
multilink bundle-name authenticated
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp key <presharedkey> address xxx.xxx.xxx.xxx no-xauth
crypto ipsec transform-set 3DESSHA esp-3des esp-sha-hmac
crypto ipsec profile IPSEC-VPN
set transform-set 3DESSHA
archive
log config
hidekeys
interface Tunnel0
description --- IPSec Tunnel to KX ---
ip address 172.30.99.10 255.255.255.252
ip ospf mtu-ignore
load-interval 30
tunnel source Vlan1
tunnel destination xxx.xxx.xxx.xxx
tunnel mode ipsec ipv4
tunnel protection ipsec profile IPSEC-VPN
interface ATM0
no ip address
shutdown
no atm ilmi-keepalive
interface FastEthernet0
description DATA
spanning-tree portfast
interface FastEthernet1
description VOICE
switchport access vlan 100
switchport voice vlan 100
spanning-tree portfast
interface FastEthernet2
shutdown
interface FastEthernet3
switchport access vlan 666
no cdp enable
spanning-tree portfast
interface Vlan1
ip address 172.30.99.1 255.255.255.252
ip nat inside
ip virtual-reassembly
interface Vlan666
ip address 192.168.1.139 255.255.255.0
ip nat outside
ip virtual-reassembly
interface Dialer0
no ip address
ip default-gateway 192.168.1.254
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 192.168.1.254
ip route 10.20.0.0 255.255.0.0 Tunnel0
ip route 10.21.0.0 255.255.0.0 Tunnel0
ip route 64.156.192.220 255.255.255.255 Tunnel0
ip route 64.156.192.245 255.255.255.255 Tunnel0
ip route 74.50.50.16 255.255.255.255 Tunnel0
ip route 74.50.63.14 255.255.255.255 Tunnel0
ip route 172.16.0.0 255.240.0.0 Tunnel0
ip route 172.30.99.0 255.255.255.0 Vlan1
no ip http server
no ip http secure-server
ip dns server
ip nat inside source list 100 interface Vlan666 overload
access-list 100 permit ip 172.30.99.0 0.0.0.255 any
access-list 199 permit icmp any any
snmp-server community public RO
snmp-server community blobby RW
control-plane
line con 0
password
login
no modem enable
line aux 0
line vty 0 4
password
login
scheduler max-task-time 5000
ntp server 72.8.140.222
ntp server 172.20.0.120
ntp server 172.20.0.121
end
Hope someone can help!

And pretty much an hour to the time of when it dropped out, it's kicked back in:
02:00:40: ISAKMP (0): received packet from dport 500 sport 500 Global (N) NEW SA
02:00:40: %CRYPTO-4-IKMP_NO_SA: IKE message from has no SA and is not an initialization offer
02:00:42: ISAKMP (0): received packet from dport 500 sport 500 Global (N) NEW SA
02:00:45: ISAKMP (0): received packet from dport 500 sport 500 Global (N) NEW SA
02:00:45: ISAKMP (0): received packet from dport 500 sport 500 Global (N) NEW SA
02:00:50: ISAKMP (0): received packet from dport 500 sport 500 Global (N) NEW SA
02:00:50: ISAKMP (0): received packet from dport 500 sport 500 Global (N) NEW SA
02:00:55: ISAKMP (0): received packet from dport 500 sport 500 Global (N) NEW SA
02:00:57: IPSEC(sa_request): ,
(key eng. msg.) OUTBOUND local= 172.30.99.1, remote= ,
    local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
    remote_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
    protocol= ESP, transform= esp-3des esp-sha-hmac (Tunnel),
    lifedur= 3600s and 4608000kb,
    spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x0
02:00:57: IPSEC(lifetime_expiry): SA lifetime threshold reached, expiring in 68 seconds
02:00:57: ISAKMP: set new node 0 to QM_IDLE
02:00:57: SA has outstanding requests (local 132.76.193.228 port 500, remote 132.76.193.200 port 500)
02:00:57: ISAKMP:(2002): sitting IDLE. Starting QM immediately (QM_IDLE      )
02:00:57: ISAKMP:(2002):beginning Quick Mode exchange, M-ID of 1560671909
02:00:57: ISAKMP:(2002):QM Initiator gets spi
02:00:57: ISAKMP:(2002): sending packet to my_port 500 peer_port 500 (I) QM_IDLE
02:00:57: ISAKMP:(2002):Sending an IKE IPv4 Packet.
02:00:57: ISAKMP:(2002):Node 1560671909, Input = IKE_MESG_INTERNAL, IKE_INIT_QM
02:00:57: ISAKMP:(2002):Old State = IKE_QM_READY New State = IKE_QM_I_QM1
02:00:58: ISAKMP (2002): received packet from dport 500 sport 500 Global (I) QM_IDLE
02:00:58: ISAKMP: set new node 1105416027 to QM_IDLE
02:00:58: ISAKMP:(2002): processing HASH payload. message ID = 1105416027
02:00:58: ISAKMP:(2002): processing SA payload. message ID = 1105416027
02:00:58: ISAKMP:(2002):Checking IPSec proposal 1
02:00:58: ISAKMP: transform 1, ESP_3DES
02:00:58: ISAKMP:   attributes in transform:
02:00:58: ISAKMP:      SA life type in seconds
02:00:58: ISAKMP:      SA life duration (basic) of 3600
02:00:58: ISAKMP:      encaps is 1 (Tunnel)
02:00:58: ISAKMP:      key length is 192
02:00:58: ISAKMP:      authenticator is HMAC-SHA
02:00:58: ISAKMP:(2002):atts are acceptable.
02:00:58: ISAKMP:(2002):Checking IPSec proposal 1
02:00:58: ISAKMP: transform 2, ESP_3DES
02:00:58: ISAKMP:   attributes in transform:
02:00:58: ISAKMP:      SA life type in seconds
02:00:58: ISAKMP:      SA life duration (basic) of 3600
02:00:58: ISAKMP:      encaps is 1 (Tunnel)
02:00:58: ISAKMP:      authenticator is HMAC-SHA
02:00:58: ISAKMP:(2002):atts are acceptable.
02:00:58: IPSEC(validate_proposal_request): proposal part #1
02:00:58: IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) INBOUND local= 172.30.99.1, remote= ,
    local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
    remote_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
    protocol= ESP, transform= NONE (Tunnel),
    lifedur= 0s and 0kb,
    spi= 0x0(0), conn_id= 0, keysize= 192, flags= 0x0
02:00:58: Crypto mapdb : proxy_match
        src addr     : 0.0.0.0
        dst addr     : 0.0.0.0
        protocol     : 0
        src port     : 0
        dst port     : 0
02:00:58: ISAKMP:(2002): processing NONCE payload. message ID = 1105416027
02:00:58: ISAKMP:(2002): processing ID payload. message ID = 1105416027
02:00:58: ISAKMP:(2002): processing ID payload. message ID = 1105416027
02:00:58: ISAKMP:(2002):QM Responder gets spi
02:00:58: ISAKMP:(2002):Node 1105416027, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
02:00:58: ISAKMP:(2002):Old State = IKE_QM_READY New State = IKE_QM_SPI_STARVE
02:00:58: ISAKMP:(2002): Creating IPSec SAs
02:00:58:         inbound SA from to 172.30.99.1 (f/i) 0/ 0
        (proxy 0.0.0.0 to 0.0.0.0)
02:00:58:         has spi 0x48E03F51 and conn_id 0
02:00:58:         lifetime of 3600 seconds
02:00:58:         outbound SA from 172.30.99.1 to (f/i) 0/0
        (proxy 0.0.0.0 to 0.0.0.0)
02:00:58:         has spi 0xD4AF8B3C and conn_id 0
02:00:58:         lifetime of 3600 seconds
02:00:58: ISAKMP:(2002): sending packet to my_port 500 peer_port 500 (I) QM_IDLE
02:00:58: ISAKMP:(2002):Sending an IKE IPv4 Packet.
02:00:58: ISAKMP:(2002):Node 1105416027, Input = IKE_MESG_INTERNAL, IKE_GOT_SPI
02:00:58: ISAKMP:(2002):Old State = IKE_QM_SPI_STARVE New State = IKE_QM_R_QM2
02:00:58: IPSEC(key_engine): got a queue event with 1 KMI message(s)
02:00:58: Crypto mapdb : proxy_match
        src addr     : 0.0.0.0
        dst addr     : 0.0.0.0
        protocol     : 0
        src port     : 0
        dst port     : 0
02:00:58: IPSEC(crypto_ipsec_sa_find_ident_head): reconnecting with the same proxies and peer
02:00:58: IPSEC(create_sa): sa created,
(sa) sa_dest= 172.30.99.1, sa_proto= 50,
    sa_spi= 0x48E03F51(1222655825),
    sa_trans= esp-3des esp-sha-hmac , sa_conn_id= 5
    sa_lifetime(k/sec)= (4450631/3600)
02:00:58: IPSEC(create_sa): sa created,
(sa) sa_dest= , sa_proto= 50,
    sa_spi= 0xD4AF8B3C(3568274236),
    sa_trans= esp-3des esp-sha-hmac , sa_conn_id= 6
    sa_lifetime(k/sec)= (4450631/3600)
02:00:58: ISAKMP (2002): received packet from dport 500 sport 500 Global (I) QM_IDLE
02:00:58: ISAKMP:(2002):deleting node 1105416027 error FALSE reason "QM done (await)"
02:00:58: ISAKMP:(2002):Node 1105416027, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
02:00:58: ISAKMP:(2002):Old State = IKE_QM_R_QM2 New State = IKE_QM_PHASE2_COMPLETE
02:00:58: IPSEC(key_engine): got a queue event with 1 KMI message(s)
02:00:58: IPSEC(key_engine_enable_outbound): rec'd enable notify from ISAKMP
02:00:58: IPSEC(key_engine_enable_outbound): enable SA with spi 3568274236/50
02:00:58: IPSEC(update_current_outbound_sa): updated peer current outbound sa to SPI D4AF8B3C
02:00:59: ISAKMP (2002): received packet from dport 500 sport 500 Global (I) QM_IDLE
02:00:59: ISAKMP: set new node -1124267365 to QM_IDLE
02:00:59: ISAKMP:(2002): processing HASH payload. message ID = -1124267365
02:00:59: ISAKMP:(2002): processing DELETE payload. message ID = -1124267365
02:00:59: ISAKMP:(2002):peer does not do paranoid keepalives.
02:00:59: ISAKMP:(2002):deleting node -1124267365 error FALSE reason "Informational (in) state 1"
02:00:59: IPSEC(key_engine): got a queue event with 1 KMI message(s)
02:00:59: IPSEC(key_engine_delete_sas): rec'd delete notify from ISAKMP
02:00:59: IPSEC(key_engine_delete_sas): delete SA with spi 0xBDD33AB1 proto 50 for
02:00:59: IPSEC(delete_sa): deleting SA,
(sa) sa_dest= 172.30.99.1, sa_proto= 50,
    sa_spi= 0x539777E6(1402435558),
    sa_trans= esp-3des esp-sha-hmac , sa_conn_id= 3
    sa_lifetime(k/sec)= (4412467/3600),
(identity) local= 172.30.99.1, remote= ,
    local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
    remote_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4)
02:00:59: IPSEC(delete_sa): deleting SA,
(sa) sa_dest= , sa_proto= 50,
    sa_spi= 0xBDD33AB1(3184736945),
    sa_trans= esp-3des esp-sha-hmac , sa_conn_id= 4
    sa_lifetime(k/sec)= (4412467/3600),
(identity) local= 172.30.99.1, remote= ,
    local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
    remote_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4)
02:01:00: ISAKMP (2002): received packet from dport 500 sport 500 Global (I) QM_IDLE
02:01:00: ISAKMP: set new node -2105526428 to QM_IDLE
02:01:00: ISAKMP:(2002): processing HASH payload. message ID = -2105526428
02:01:00: ISAKMP:(2002): processing NOTIFY DPD/R_U_THERE protocol 1
        spi 0, message ID = -2105526428, sa = 844CC060
02:01:00: ISAKMP:(2002):deleting node -2105526428 error FALSE reason "Informational (in) state 1"
02:01:00: ISAKMP:(2002):Input = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY
02:01:00: ISAKMP:(2002):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
02:01:00: ISAKMP:(2002):DPD/R_U_THERE received from peer , sequence 0x22D
02:01:00: ISAKMP: set new node 971443288 to QM_IDLE
02:01:00: ISAKMP:(2002):Sending NOTIFY DPD/R_U_THERE_ACK protocol 1
        spi 2220478360, message ID = 971443288
02:01:00: ISAKMP:(2002): seq. no 0x22D
02:01:00: ISAKMP:(2002): sending packet to my_port 500 peer_port 500 (I) QM_IDLE
02:01:00: ISAKMP:(2002):Sending an IKE IPv4 Packet.
02:01:00: ISAKMP:(2002):purging node 971443288
02:01:00: ISAKMP:(2002):Input = IKE_MESG_FROM_PEER, IKE_MESG_KEEP_ALIVE
02:01:00: ISAKMP:(2002):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
02:01:02: ISAKMP (2002): received packet from dport 500 sport 500 Global (I) QM_IDLE
02:01:02: ISAKMP:(2002): processing HASH payload. message ID = 1560671909
02:01:02: ISAKMP:(2002): processing SA payload. message ID = 1560671909
02:01:02: ISAKMP:(2002):Checking IPSec proposal 1
02:01:02: ISAKMP: transform 1, ESP_3DES
02:01:02: ISAKMP:   attributes in transform:
02:01:02: ISAKMP:      encaps is 1 (Tunnel)
02:01:02: ISAKMP:      SA life type in seconds
02:01:02: ISAKMP:      SA life duration (basic) of 3600
02:01:02: ISAKMP:      SA life type in kilobytes
02:01:02: ISAKMP:      SA life duration (VPI) of 0x0 0x46 0x50 0x0
02:01:02: ISAKMP:      authenticator is HMAC-SHA
02:01:02: ISAKMP:(2002):atts are acceptable.
02:01:02: IPSEC(validate_proposal_request): proposal part #1
02:01:02: IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) INBOUND local= 172.30.99.1, remote= ,
    local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
    remote_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
    protocol= ESP, transform= NONE (Tunnel),
    lifedur= 0s and 0kb,
    spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x0
02:01:02: Crypto mapdb : proxy_match
        src addr     : 0.0.0.0
        dst addr     : 0.0.0.0
        protocol     : 0
        src port     : 0
        dst port     : 0
02:01:02: ISAKMP:(2002): processing NONCE payload. message ID = 1560671909
02:01:02: ISAKMP:(2002): processing ID payload. message ID = 1560671909
02:01:02: ISAKMP:(2002): processing ID payload. message ID = 1560671909
02:01:02: ISAKMP:(2002): Creating IPSec SAs
02:01:02:         inbound SA from to 172.30.99.1 (f/i) 0/ 0
        (proxy 0.0.0.0 to 0.0.0.0)
02:01:02:         has spi 0x84F77E7D and conn_id 0
02:01:02:         lifetime of 3600 seconds
02:01:02:         lifetime of 4608000 kilobytes
02:01:02:         outbound SA from 172.30.99.1 to (f/i) 0/0
        (proxy 0.0.0.0 to 0.0.0.0)
02:01:02:         has spi 0xCA486707 and conn_id 0
02:01:02:         lifetime of 3600 seconds
02:01:02:         lifetime of 4608000 kilobytes
02:01:02: ISAKMP:(2002): sending packet to my_port 500 peer_port 500 (I) QM_IDLE
02:01:02: ISAKMP:(2002):Sending an IKE IPv4 Packet.
02:01:02: ISAKMP:(2002):deleting node 1560671909 error FALSE reason "No Error"
02:01:02: ISAKMP:(2002):Node 1560671909, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
02:01:02: ISAKMP:(2002):Old State = IKE_QM_I_QM1 New State = IKE_QM_PHASE2_COMPLETE
02:01:02: IPSEC(key_engine): got a queue event with 1 KMI message(s)
02:01:02: Crypto mapdb : proxy_match
        src addr     : 0.0.0.0
        dst addr     : 0.0.0.0
        protocol     : 0
        src port     : 0
        dst port     : 0
02:01:02: IPSEC(crypto_ipsec_sa_find_ident_head): reconnecting with the same proxies and peer
02:01:02: IPSEC(create_sa): sa created,
(sa) sa_dest= 172.30.99.1, sa_proto= 50,
    sa_spi= 0x84F77E7D(2230812285),
    sa_trans= esp-3des esp-sha-hmac , sa_conn_id= 7
    sa_lifetime(k/sec)= (4550947/3600)
02:01:02: IPSEC(create_sa): sa created,
(sa) sa_dest= , sa_proto= 50,
    sa_spi= 0xCA486707(3393742599),
    sa_trans= esp-3des esp-sha-hmac , sa_conn_id= 8
    sa_lifetime(k/sec)= (4550947/3600)
02:01:02: IPSEC(update_current_outbound_sa): updated peer current outbound sa to SPI CA486707
02:01:02: IPSEC(check_delete_duplicate_sa_bundle): found duplicated fresh SA bundle, aging it out. min_spi=48E03F51
02:01:02: IPSEC(early_age_out_sibling): sibling outbound SPI D4AF8B3C expiring in 30 seconds due to it's a duplicate SA bundle.
02:01:03: ISAKMP (2002): received packet from dport 500 sport 500 Global (I) QM_IDLE
02:01:03: ISAKMP: set new node 2041302203 to QM_IDLE
02:01:03: ISAKMP:(2002): processing HASH payload. message ID = 2041302203
02:01:03: ISAKMP:(2002): processing DELETE payload. message ID = 2041302203
02:01:03: ISAKMP:(2002):peer does not do paranoid keepalives.
02:01:03: ISAKMP:(2002):deleting node 2041302203 error FALSE reason "Informational (in) state 1"
02:01:03: IPSEC(key_engine): got a queue event with 1 KMI message(s)
02:01:03: IPSEC(key_engine_delete_sas): rec'd delete notify from ISAKMP
02:01:03: IPSEC(key_engine_delete_sas): delete SA with spi 0xD4AF8B3C proto 50 for
02:01:03: IPSEC(delete_sa): deleting SA,
(sa) sa_dest= 172.30.99.1, sa_proto= 50,
    sa_spi= 0x48E03F51(1222655825),
    sa_trans= esp-3des esp-sha-hmac , sa_conn_id= 5
    sa_lifetime(k/sec)= (4450631/3600),
(identity) local= 172.30.99.1, remote= ,
    local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
    remote_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4)
02:01:03: IPSEC(delete_sa): deleting SA,
(sa) sa_dest= , sa_proto= 50,
    sa_spi= 0xD4AF8B3C(3568274236),
    sa_trans= esp-3des esp-sha-hmac , sa_conn_id= 6
    sa_lifetime(k/sec)= (4450631/3600),
(identity) local= 172.30.99.1, remote= ,
    local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
    remote_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4)
02:01:48: ISAKMP:(2002):purging node 1105416027
02:01:49: ISAKMP:(2002):purging node -1124267365
02:01:50: ISAKMP:(2002):purging node -2105526428
02:01:52: ISAKMP:(2002):purging node 1560671909
02:01:53: ISAKMP:(2002):purging node 2041302203

Old printer with new wireless modem/router

i just installed a new wireless modem/router and need to get my printer to work with my comps....i think i need to reassign the IP address and enter the wep...but dont know how

Hi dduve,
Set up a static IP address for your printer, click here and follow the steps in this document to set one up. Let me know if you need more help.
I worked on behalf of HP.

Using Airport Extreme with a Netopia Wireless Router 2247NWG

Hi, I'm trying to set up an airport extreme base station (AEBS) with a netopia wireless router and my XP SP3 Laptop. I have the extreme plugged into the router and the set up of the AEBS went fine. I have a solid green light on the AEBS and it appears to be working OK. When I move to another room in the house, I have two wireless networks available - the netopia wireless router and the AEBS. Whichever of the networks I connect to, the signal strength is extremely poor and the other is showing available with 5 bars. When I connect to the strong network, the signal goes weak and the original network is available with 5 bars. I've tried disabling the wireless on the router but this doesn't help. The router network is still showing as available with 5 bars but I can't connect to it.
First day with my MAC gear (haven't even opened the MacBook box yet) and I need help!!!!!!!!!!!

So, today I finally broke down and plugged them both into the two available ports in the back of the AEBSn via ethernet cables. My question is: Do I have to "turn off" the airport connection in order to make the ethernet connection the default connection?
That might help but it isn't necessary. You can simply rearrange the order of items in the Network preference pane.
Search on the internet and you will find many ways to check the speed. One is http://us.mcafee.com/root/speedometer/default.asp

Problems with Westell 327w

With my own laptop I have no problems with a wireless connection. However, when someone else comes over and we try to connect a different wireless laptop we are able to connect to the westell using a WEP key but we cant get on the internet. 4x is disabled. Authentication is open. WEP enabled. MAC filtering and hide SSID are disabled. Can you please help? This has happened with both XP and Vista machines.

I, too, have the Westell 327. I get good download speeds to my desktop, but very weak signal to my laptop and downstairs devices, so after a hired tech tried to get it to work better, he suggested a range extender. Now,$100 later, it seemed to work for about a week, so I made my first of tho on-line chats with online support. After three hours, I made the mistake of allowing a remote access to my setup. Ater changing some settings on my Westell 327, he ignored that little "you're about to lose wireless connectivity, and promptly dropped the session. Two hours later, no call back despite his having both my home (dsl) and cell numbers. So I logged on again the next day. Three more hours, and no result. They seem always to assume it's something wrong with my laptop, and ignore repeated requests for a better modem/router. The tech mentioned the Westell 7500 and an "Action Tech", but refused to provide information and just kept saying I'd have to talk to billing. I don't want to buy a router to replace the deffective one they sent me. But, if that's the only thing that will work, please let us know what kind to buy, where and how much it cost. I can't wait for FIOS to come to town! Thanks.

Using WRT610N router with Westell 327W modem/router on Centurytel

Similar Messages

Maybe you are looking for