UWL COnfiguration(Connecters is not successfully connected)

Hi,
We are configuring UWL on portal.
Folowing are the steps we followed for UWL configuration in terms for Portal as well as Backend.
Backend:-
1)SWU3 configuration is done.
2)created UWL_Server with all the authorization.
SAP_BC_BMT_WFM_UWL_END_USER
SAP_BC_UWL_END_USER
SAP_BC_UWL_SERVICE
Portal:-
1)Created one RFC through Visual Administrator
2)Deployed one .SDA sonic connectors
2)Created one system with SAP_R3_Workflow alias name but
getting an error while testing connectors
Test Connection with Connector
Test Details:
The test consists of the following steps:
1. Retrieve the default alias of the system
2. Check the connection to the backend application using the connector defined in this system object
Results
Retrieval of default alias successful
Connection failed. Make sure that Single Sign-On is configured correctly
I believe by the time we donot configure the connectors sucessfully until we
will not be able to register service in System_administration->system Configuration
->Universal Worklist.
Please give you input that how we can manage to acivate the test connection of connectors.

Hi Rishav,
Please post this thread in portal related forum so that you will get appropriate replies..
Rgds,
Bharath

Similar Messages

Reading of configuration of AEBS not successful...?

I'm quite surprised - first time no "plug&play", most likely a user problem...
Just tried to start configuring my new AEBS, connected BS to DSL modem and power - connected to iMac via WLAN, detected by software, started reading configuration of the base ....
But the reading of the configuration is never ending... what may be wrong? It just continues reading.... never giving any chance to set anything.
It tries to read the current configuration and never succeeds in showing the configuration, not to speak of a chance to set the configuration to my provider values etc.
Who may help?
Thanks a lot!

I have the same problem, but it doesn't work if I try an ethernet cable either. The first time I encountered this problem (only a day or two after purchase) , I did a hard reset, but a day later I am in the same situation. Any suggestions?
MacBook Core2 Duo 2.0 Mac OS X (10.4.8) 1 Gb SDRAM

Wireless Network Does Not Always Connect Successfully on HP ENVY 5644

Just purchased a new HP ENVY 5644 device to replace an existing my HP Photosmart C4380. Powered the new device on for the first time and ran through the initial setup using the integrated touchscreen. Everything seemed to go both easily and smoothly, without any errors and even connected to my home wireless network on the first attempt.
I next tested both printing and scanning features, each of which provided extremely pleasing results and good performance over the wireless network.
Unfortunately, this is where my happy story ends and the trouble begins!
Having initially setup the device in a temporary location, I correctly powered down in preparation of relocating it to its final resting position. Although this was to be in a different room of the house, it was in fact closer to the wireless network router itself. In reality, we are talking a very negligible distance as the 2 rooms are actually back to back to one another. So now with it in the new position and connected to a power outlet, I switched the device on once again. The device powers up and the blue LED indicator which signifies the wireless connection status, continuously flashes blue rather than a steady solid blue. The flashing blue indicates that the device cannot establish a wireless network connection. If I use the touchscreen to investigate the issue I find that there appears to be an Authentication Problem and the message details are Incorrect wireless password (WPA) entered.
Why has this happened? Nothing has changed, all I did is move the printer into another room!
Believing what the touchscreen tells me, I decided to run the Wireless Setup Wizard once more to affirm the wireless network settings. As expected, it manages to find my home wireless network without any issues and then requests that the password key is entered. I therefore enter this correctly and press apply. It is at this point that the device attempts to make a connection to the network, which unfortunately fails, returning the above error message. However, I know that I entered the password correctly, in fact there is an option to show the password you have entered prior to attempting the connection, which upon checking confirms that the password I entered is the correct one!
So why does it not connect?
I have tried switching the wireless feature on and off several times via the touchscreen interface but this did not resolve the issue. The only way to get the wireless connection back online is to keep switching the device on and off again until the wireless LED indicator stays on solid blue. For no apparent reason, the wireless connection seems to have a mind of its own, only successfully connecting to my wireless network when it wishes to!
I do not have any issues with the numerous other wireless network devices I have in my home, from multiple manufacturers and even located in other multiple rooms of the home. I know my wireless network is good and I know my wireless password like the back of my own hand, so there is no chance of this being incorrect. This is purely a problem for the HP ENVY 5644 device itself, which can be confirmed by the fact that if I switch it off and on again, it might decide to make a successful connection even though I did nothing to its own network configuration nor to my own wireless network configuration itself.
Wondering whether or not it might be some obscure incompatibility between my wireless router and the HP ENVY 5644, I tested the device with another spare router that I have, which was also from a different manufacturer but sadly the result was the same, the HP ENVY 5644 only connected when it wanted to and would only establish the connection to the wireless network upon switching on the device. If the connection fails, it will never connect to the network unless you switch it off and then back on again, which might even require to be attempted several times before successful. Once connected, it appears to remain connected and then functions really well.
This behaviour is not acceptable and I’m sure this can’t be too healthy for the device itself to be switched on and off again in such short cycles. Otherwise, on the whole, as I said earlier, I am very happy with the product.
Can someone at HP tell me why this is happening or suggest what else I need to look for or consider.

Spoke with HP engineer the other day. I explained what was happening and they suggested doing a factory reset and then setting the IP address manually rather than using the DHCP of my home wireless router.
I wasn't too happy about that as everything was setup nicely and working, with the exception of the WiFi not reconnecting on every power on. I had also gone one better in fact, by adding a DHCP reservation within my router using the MAC address of the printer. This in effect is the best of both worlds as the printer will be given the same IP address by the router every time it requests one.
We agreed to leave things as they stand rather than factory reset the printer and that I would now power off the printer everyday. For the past 4 days, the printer has reconnected to the WiFi upon every power on. This is great news.
I have a call scheduled with HP in a few days time to discuss how things have been going. If all continues as is, it would appear than specifying a DHCP reservation in the wireless router resolves the issue. Whilst I await the next call with HP, I am continuing to power on and off the printer on a daily basis.
Watch this space!

Configuration data download to FPGA was not successful.

I have designed a board with the Spartan 6 LX9 TQFP144 Package.
I am able to load a bitstream to the device with the digilent HS-2. However the fpga can not selfconfigure from
the attached SPI Flash.
Here is the console output from iMPACT:
GUI --- Auto connect to cable...
INFO:iMPACT - Digilent Plugin: Plugin Version: 2.4.4
INFO:iMPACT - Digilent Plugin: found 1 device(s).
INFO:iMPACT - Digilent Plugin: opening device: "JtagHs2", SN:210249983579
INFO:iMPACT - Digilent Plugin: User Name: JtagHs2
INFO:iMPACT - Digilent Plugin: Product Name: Digilent JTAG-HS2
INFO:iMPACT - Digilent Plugin: Serial Number: 210249983579
INFO:iMPACT - Digilent Plugin: Product ID: 30900152
INFO:iMPACT - Digilent Plugin: Firmware Version: 0109
INFO:iMPACT - Digilent Plugin: JTAG Port Number: 0
INFO:iMPACT - Digilent Plugin: JTAG Clock Frequency: 10000000 Hz
Attempting to identify devices in the boundary-scan chain configuration...
INFO:iMPACT - Current time: 27.07.2015 16:19:26
PROGRESS_START - Starting Operation.
Identifying chain contents...'0': : Manufacturer's ID = Xilinx xc6slx9, Version : 2
INFO:iMPACT:1777 -
Reading C:/Xilinx/ISE/14.7/ISE_DS/ISE/spartan6/data/xc6slx9.bsd...
INFO:iMPACT:501 - '1': Added Device xc6slx9 successfully.
done.
PROGRESS_END - End Operation.
Elapsed time = 0 sec.
Selected part: N25Q128
Unprotect sectors: FALSE
INFO:iMPACT - Current time: 27.07.2015 16:20:19
PROGRESS_START - Starting Operation.
Maximum TCK operating frequency for this device chain: 25000000.
Validating chain...
Boundary-scan chain validated successfully.
'1': SPI access core not detected. SPI access core will be downloaded to the device to enable operations.
INFO:iMPACT - Downloading core file C:/Xilinx/ISE/14.7/ISE_DS/ISE/spartan6/data/xc6slx9_spi.cor.
'1': Downloading core...
LCK_cycle = NoWait.
LCK cycle: NoWait
done.
'1': Reading status register contents...
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0011 1100 1110 1100
INFO:iMPACT:2492 - '1': Completed downloading core to device.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
'1': Erasing Device.
'1': Using Sector Erase.
'1': Programming Flash.
'1': Reading device contents...
done.
'1': Verification completed.
'1':Programming in x4 mode.
'1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
INFO:iMPACT - '1': Flash was not programmed successfully.
PROGRESS_END - End Operation.
Elapsed time = 78 sec.
If i read that correctly Data was written to the Flash but the fpga was not able to configure from that data.
Done-pin is connected to 3.3V via a 470 Ohms Resisor.
The Flash is a N25Q128A13ESE40G, Datasheet here: http://www.farnell.com/datasheets/1674445.pdf
I can perform a readback, checksum and an erase.
If i do a read device status this is the console output:
INFO:iMPACT - Current time: 27.07.2015 16:36:27
Maximum TCK operating frequency for this device chain: 25000000.
Validating chain...
Boundary-scan chain validated successfully.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
INFO:iMPACT - '1': Reloading FPGA configuration data stored in flash...
INFO:iMPACT:182 - done.
On the Flash side I have pulled s# and Hold up to 3.3V with 100k Resistors.
Can someone help me to find the problem?

So does the FPGA try to read the SPI flash when it boots ?
out with scope, probe the clock and the data , see if you can see it streamig out when you boot.
If so, then one other thing I see wrong a few times is data path of the SPI, single bit or 4 bits of data.
you have to make certain the bit file was created in the same width as the fgpa is expecting,
In ISE I think its in Impact where you make the SPI flash file and specify this .

My wireless keyboard no longer connects with my iMac since changing the batteries. It now shows as not connected, not paired and not configured. A friend recently connected his iPad to the iMac and since then the problem started. Any ideas to resolve this

My wireless keyboard no longer connects with my iMac since changing the batteries. It now shows as not connected, not paired and not configured. A friend recently connected his iPad to the iMac and since then the problem started. Any ideas to resolve this?

a friend told me that he wants my os x cd for my macbook pro to upgrade his imac.
The discs that come with your Mac are "machine specfic" and cannot be used on another Mac.

Blackberry passport cannot connect to win 7 pro device driver software was not successfully installed

I cannot get my passport to connect to eather of my PC's, one is running Win 7 Pro 64bit, and one is running Win 7 pro 32bit. both pc's give me the same driver error-"device driver software was not successfully installed" i have latest versions of Link and Blend installed on the pc's, and 10.3.0.908 on my pasport madel SQW100-1

same issue here for a z2, only windows 7 pro on virtualbox in ubuntu (linux)
very good service from sony that they reply instantly..
whats the point in a exceptional good phone with poor support??
if this poor service continues, this would be definatly my last sony device..
and build a linux version of your crappy software!! android IS linux so you have plenty developers..

I just downloaded a new software update to my ipod touch and now my ipod is frozen with a screen picture of music round blue symbol and an arrow displaying a cable connection. I received a message saying that the download was not successful.

I just downloaded a new software update to my ipod touch and now the ipod and screen are frozen. I received a message that the download was not successful and now my screen is showing the blue round itunes symbol with an arrow pointing to the symbol and shows a cable below it. I have tried the restart of pushing the two buttons together and waiting 10 seconds for the apple symbol which appears and then go backs to the same stuck symbol. My computer is not recognizing the ipod either and will not connect. What needs to be done? Thanks.

Try manually placin the iPod in Recovery Mode and restore via iTunes.
Next try DFU mode and restore
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings

Virtex6:Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings

Hello，everyone.
I am using virtex6 FPGA and trying to download mcs file to PROM and have failed.
I download .bit file to FPGA and succeed.
When i try to download .mcs file to PROM XCF128X-FTG64C(BPI Flash) and choose Slave SelectMAP Mode
and the process is about 68% it fails.
The message below the IMapct is as belows:
done.
PROGRESS_END - End Operation.
Elapsed time =      0 sec.
// *** BATCH CMD : identifyMPM
// *** BATCH CMD : assignFile -p 1 -file "C:/Users/Administrator/Desktop/TEST/LED/led.bit"
'1': Loading file 'C:/Users/Administrator/Desktop/TEST/LED/led.bit' ...
done.
INFO:iMPACT:2257 - Startup Clock has been changed to 'JtagClk' in the bitstream stored in memory,
but the original bitstream file remains unchanged.
UserID read from the bitstream file = 0xFFFFFFFF.
INFO:iMPACT:501 - '1': Added Device xc6vlx240t successfully.
INFO:iMPACT - Current time: 2014/3/13 8:48:14
// *** BATCH CMD : Program -p 1
PROGRESS_START - Starting Operation.
Maximum TCK operating frequency for this device chain: 66000000.
Validating chain...
Boundary-scan chain validated successfully.
INFO:iMPACT - 1: Over-temperature condition detected! [ 230.52C > 120.00C]
1: Device Temperature: Current Reading: 230.52 C, Max. Reading: 230.52 C
1: VCCINT Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
1: VCCAUX Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
'1': Programming device...
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
done.
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0011 1111 0111 1110 0100 1011 1100 0000
INFO:iMPACT:579 - '1': Completed downloading bit file to device.
INFO:iMPACT:188 - '1': Programming completed successfully.
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
INFO:iMPACT - '1': Checking done pin....done.
'1': Programmed successfully.
PROGRESS_END - End Operation.
Elapsed time =     23 sec.
Selected part: XCF128X
// *** BATCH CMD : attachflash -position 1 -bpi "XCF128X"
// *** BATCH CMD : assignfiletoattachedflash -position 1 -file "C:/Users/Administrator/Desktop/TEST/LED/leda.mcs"
INFO:iMPACT - Current time: 2014/3/13 8:49:32
// *** BATCH CMD : Program -p 1 -dataWidth 16 -rs1 NONE -rs0 NONE -bpionly -e -v -loadfpga
PROGRESS_START - Starting Operation.
Maximum TCK operating frequency for this device chain: 66000000.
Validating chain...
Boundary-scan chain validated successfully.
INFO:iMPACT - 1: Over-temperature condition detected! [ 230.52C > 120.00C]
1: Device Temperature: Current Reading: 230.52 C, Max. Reading: 230.52 C
1: VCCINT Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
1: VCCAUX Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
'1': BPI access core not detected. BPI access core will be downloaded to the device to enable operations.
INFO:iMPACT - Downloading core file D:/Xilinx/14.3/ISE_DS/ISE/virtex6/data/xc6vlx240t_jbpi.cor.
'1': Downloading core...
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
done.
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0011 1111 0111 1110 0100 1011 1100 0000
INFO:iMPACT:2492 - '1': Completed downloading core to device.
Current cable speed is set to 6.000 Mhz.
Cable speed is default to 3Mhz or lower for BPI operations.
Current cable speed is set to 3.000 Mhz.
Setting Flash Control Pins ...
Setting Configuration Register ...
Populating BPI common flash interface ...
Common Flash Interface Information Query completed successfully.
INFO:iMPACT - Common Flash Interface Information from Device:
INFO:iMPACT - Verification string: 51 52 59
INFO:iMPACT - Manufacturer ID:        49
INFO:iMPACT - Vendor ID:             01
INFO:iMPACT - Device Code:           18
Setting Flash Control Pins ...
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
'1': Erasing device...
'1': Start address = 0x00000000, End address = 0x008CE03B.
done.
'1': Erasure completed successfully.
Setting Flash Control Pins ...
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
INFO:iMPACT - Using Word Programming.
'1': Programming Flash.
done.
Setting Flash Control Pins ...
'1': Flash Programming completed successfully.
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
'1': Reading device contents...
done.
'1': Verification completed.
Setting Flash Control Pins ...
Current cable speed is resumed to 6.000 Mhz.
'1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
`Elapsed time =    814 sec.
and i find many people have met the same thing. But they are spartan series FPGA and i try to low the Resistances of Mode pins,M0 M1 and M2, but the problem does not been solved.
I have read the status Registers and find there is an over-temperature state
and in Impact i could not readback the registers. It is strange.
I am anxious about this problem and have not solved it yet
What reasons may it be?
Hope for your answer, thank you

Hi~I want to know if you solve the configuration problem for virtex-6?
As I encounter the  same configuration problem, I want to consult  you with some question.
Can I have your email?
gszakacs wrote:
I have measured the VCCINT and find it is 1.0V, not 2.997V;
That is not at all surprising. I always assumed the problem is with reading the XADC (system monitor) block and not with the voltage or temperature.
my Reference board is ML605
That would have been nice to know at the beginning...
It seems that you have selected the correct mode, assuming your jumpers are set as required in the ML605 Hardware User's Guide. See table 1-27, table 1-33 and the note below it about switch S1.
I'm not that familiar with the details of this reference design, but it may be that the slave SelectMap circuitry requires a reset or power cycle to actually configure the FPGA. Have you tried power-cycling to see if the FPGA boots from the flash?
I'd also suggest that you select the V6 in the JTAG chain view, then go to the debug menu of Impact and select Read Device Status (this is from memory, but it's something like that). That will not only show the bits of the configuration status register, but also describe what each bit means. Among other things you can check the state of the FPGA's configuration logic and the Mode pins.

When plugging in an iPad in Apple Configurator, it is not being read under USB Connected so I can't update it. Any ideas on how to get the system to read the iPad?

When plugging in an iPad in Apple Configurator, it is not being read under USB Connected so I can't update it. The iPhoto window opens up and reads the photos on the iPad, so it is connecting to the computer. Earlier today I wasn't having any problems. I have shut down the iPad and the computer and started over, but that didn't help. Any ideas on how to get the system to read the iPad so I can update the apps on it?

Hi, is the problem just to update your apps on your iPad? Here is what you should check. Is the iTunes on your computer updated to the latest version? Does your iPad needs to be updated? Do you have enough storage on your iPad to do the update? On your device is your iCloud back up checked?
Go to Settings - iCloud - Backup/Storage - see if its checked, and try unchecking it before connecting it to the computer.
Please let me know if you need any further assistance.

V5 in BPI Mode " Configuration data download to FPGA was not successful. DONE did not go high,"

Hello，everyone.
I am using virtex5 XC5VLX155 FPGA and trying to download mcs file to BPI flash and have failed.
The flash is JS28F512P30E. The iMpact version is 14.7.
FPGA's VCCINT is 1.0V, VCCAUX is 2.5V. VCCO is 3.3V.
M[2:0] is 010 in Master BPI. Ican program FPGA through JTAG. The FPGA_DONE pin 's LED can always flash.
The error is shown as below. the full IMPACT console log and the SCHEMATIC_ FLASH are in the attachment.
Using x16 mode ...
Setting Flash Control Pins ...
'1': Erasing device...
'1': Start address = 0x00000000, End address = 0x004E4AFF.
done.
'1': Erasure completed successfully.
Using x16 mode ...
Setting Flash Control Pins ...
INFO:iMPACT - Using Word Programming.
'1': Programming Flash.
done.
'1': Flash Programming completed successfully.
'1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
PROGRESS_END - End Operation.
Elapsed time = 692 sec.
Hope everyone give more advices. Thank you.

Thank you very much!
I can read ack the mcs file, but the file is much bigger than the original mcs file.
The flash datasheet is in the attachment.
I want to use the Master BPI mode. In BPI_UP, the address starts at 0 and increments by 1 until the DONE pin is
asserted. I do not know the difference between the BPI_UP and BPI_DOWN.
ps: The R61,R62 and R63 are not weld on the board. The ADV pin is tie to VSS .

Error in UWL configuration for MSS in portal..

HI,
I want to configure UWL in portal so that I can see/approve leave in UWL in MSS. Please let me know how to configure the same.
When I am trying to configure the UWL in system admin> system configuration> Univerasal Worklist Administration, under that i clicked in new button to add my R/3 system, in that popup i mentioned my system alias name of R/3 system and connector as Webflow connector and remaining field i kept as empty and i clicked on save button after that when i click on Register button OR Register item type for all system than I am getting the following error, please let me know what the issue is ?
Error is:
Errors:
System SandBoxCLNT300: Wed Mar 16 09:18:38 IST 2011
(Connector) :com.sap.netweaver.bc.uwl.connect.ConnectorException:Wed Mar 16 09:18:38 IST 2011
(Connector) :com.sap.portal.connectivity.destinations.PortalDestinationsServiceException:User is missing credentials for connecting to alias SandBoxCLNT300. Contact your system administrator.
SandBoxCLNT300 is the system alias of system I have created for R/3. in that system object I am using logon ticket.
Also when i try to test that system , SAP Web AS Connection AND ITS Connection connection are tested properly with green tick but the third parameter Test Connection with Connector is failing and the error is
Test Details:
The test consists of the following steps:
1. Retrieve the default alias of the system
2. Check the connection to the backend application using the connector defined in this system object
Results
Retrieval of default alias successful
Connection failed. Make sure that Single Sign-On is configured correctly
Also the transaction iview i created using this system object is coming absolutely proper, than why Test Connection with Connector is failing , please let me know , might be UWL issue is related to this one..
Thanks

Please first let us know if you have done the configuration as per
the Note 779075, Please do this and re register the work items and
let us know.
Make
Check the configuration of SAP_WebDynpro_XSS
Here is the help documentation:
http://help.sap.com/saphelp_nw70/helpdata/en/92
/a88931f2dd4631b9e8d530697d89c9/content.htm
in regards to this parameter.
IF the LeaveRequestApprover application is deployed on the SAP_Local
System, you needed the system alias of SAP_LocalSystem in the
Webdynpro Launch System value. With this setting when the user
manager clicks on the item, it will work fine.
the system SAP_Webdynrpo_XSS should have maintained the WAS properties
with the port of the portal. This is for normal working for
Leave request
"Mapping Logical Systems" in the following documentation:
http://help.sap.com/SAPHELP_NW04S/helpdata/EN/2a/7a754297fdd142e10000000
a1550b0/content.htm
and the "sap-wd-arfc-useSys" bullet point in the following
documentation:
http://help.sap.com/saphelp_sm32/helpdata/en/f4/651741f163f023e10000000a
155106/content.htm
See in bold where it mentions that "The prerequisite for this is that,
in addition to the default JCo connections, you created the new logical
system name with the Web Dynpro Content Administrator and configured it
for the required SAP system." Meaning that there needs to be a JCO
Connection for "SAP_R3_SelfServiceGenerics_MetaData" since these are
the default JCo connections. In this case I kindly ask that you create
the default metadata and model JCO connections for
SAP_R3_SelfServiceGenerics and see if that resolves the issue.

How to configure ASA to allow activesync connections ?

To allow Activesync connections (between smartphones and an internal Exchange server) thru an ASA, I think about 3 or 4 potential solutions :
1) do a NAT on the Exchange server and allow activesync TCP connections from any IP to the Exchange server : I tested that and this works, but it is not the most secure solution we can imagine;
2) use a Clienless VPN SSL ASA configuration : I tried it, but got problems certaintly related to the fact that the Activesync client, installed on my Android/Samsung smartphone, does not seem to be able vto pass properly thru the ASA Portal to reach the Exchange server;
3) use an Anyconnect VPN ASA configuration : I tried it , but did not manage to install or use any of the Samsung Anyconnect client available on Android Market; by the way, I saw, in the Anyconnect VPN Client Admin Guide 2.4, that an ActiveSync MSI is available from CISCO (
anyconnect-wince-ARMv4I-activesync-AnyConnectRelease_Number-k9.msi), but I don't see any details about how it is supposed to be used except that it is for Windows environment only, so, not for an Android phone, but I have Windows Mobile smartphones to integrate too, so, maybe it can help me in this case ;
4) if Clientless nor Anyconnect solutions can't work, it might be better to use the ASA Cut-Through proxy function to get a more secure solution than the first one listed above; but I was not successful either with this cut-through proxy function
Any ideas or examples about how to allow activesync connections thru ASA would be welcomed
thanks in advance

Hi,
Generally ASA with CSC will support HTTP,FTP,SMTP,POP3 Scaning and Filtering.
From version ASA IOS 8.4.2 and CSC 6.6.1125.0, it will support HTTPS filtering also.
But here one limitation is that Https filtering will not support earlier versions of internet explorer 9, i.e if you want HTTPS filtering you must use Internet explorer 9 or after versions( As you know that Windows XP machines won't support internet explorer 9). But with firefox HTTPS filtering will support from versions 4.
For your reference use below 8.4.2 release guide
http://www.cisco.com/en/US/docs/security/asa/asa84/release/notes/asarn84.html
Release notes for CSC version 6.6.1125
http://www.cisco.com/en/US/docs/security/csc/csc66/release/notes/cscrn66.pdf
Basic configuration of the CSC
http://www.cisco.com/en/US/docs/security/csc/csc6.1.1569.0/administration/guide/cscappa.pdf
Sending traffic to the CSC module (using ASDM and CLI)
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00808dea62.shtml
The troubleshooting guide:
http://www.cisco.com/en/US/docs/security/csc/csc63/administration/guide/csc8.html#wp1147829
Hope this will help you...
Do rate help ful posts..
Regards,
Janardhan

Anyone have any success connecting a generic PS3 controller through Mavericks on my macbook pro

Hi
I am able to connect the above controllers and play supported games via USB connection. However, bluetooth does not seemingly support these devices of which I have 2.
I have followed connection guidance for earlier versions of OSX and connect via USB to recognise the device and then remove the usb cable, press the PS button and the device is prompted to pair via bluetooth. I am using a password of "0000" to pair and key this in to my macbook but then nothing happens. The device is shown as not connected, nor paired and the "connect" option has no effect.
In system information this is what presents under bluuetooth device is configured but neither paired nor connected
ps controller orange:
Address:    00-32-00-DE-90-A1
Major Type:    Peripheral
Minor Type:    Peripheral
Services:
Paired:    No
Configured:    Yes
Connected:    No
Vendor ID:    0x054C
Product ID:    0x0268
Class of Device:    0x05 0x02 0x0508
When successfully connected via USB this is what presents:
PLAYSTATION(R)3Conteroller:
Product ID:    0x0268
Vendor ID:    0x054c (Sony Corporation)
Version:     1.00
Speed:    Up to 12 Mb/sec
Manufacturer:    SHENGHIC 2009/0708ZXW-V1Inc.
Location ID:    0x14300000 / 1
Current Available (mA):    500
Current Required (mA):    500
Anybody have any success with such a bluetooth connection .....so much better without cables after all ?
I did read one forum post indicating that one user had cloned a working PS3 controller and copying and pasting configuration data in terminal. As I don't currently have a controller that will pair that's a step too far for me.
Thanks in anticipation

Click App Store from your Apple menu  drop down menu then select Updates from the App Store menu bar.

Configuring Device - Device not reachable

My new Envy 4500 _IS_ on my network.
My new MacBook Pro _IS_ on my network.
I get to the configuration step and all looks good until I get the response below:
"Configuring Device
0 Select Device
0 Confirm Wreless Settings
O Select Network
Configuring Device
Configuration Results
Device Not Reachable
Th) wireless network settings were successfully downloaded to your device. However, your Mac
was unable to locate the device on the network.
Please make sure that:
• Your Mac is connected to a wired or wireless network that has access to your device.
• Your device is connected to the wireless network "AC Network".
Fomore information online, visithftp://www.hp.com/o/wirelessprinting"
This is the second HP printer that I am trying to configure that is doing the same darn thing. I thought the first one was faulty, so I exchanged for a slightly different printer. This one has a control screen, so I KNOW that it's on the network. And I KNOW my computer is on the network, or I wouldn't be able to write this.
But they refuse to talk with each other. SO frustrating. I'm ready to give up on HP.
Joe
This question was solved.
View Solution.

Found the problem. HP printers don't support AC Wifi. That would have been nice to know before I wasted 4 hours on 2 printers......

Does not automatically connect to recently used WIFI networks

Recently purchased 13" Macbook Air, with Lion installed. All's well, except upon start-up or waking up from sleep mode, it does not automatically re-connect to the WIFI network it was just connected to. Instead, I'd have to manually find the network to select it. (Incidentally, some of my friends who also use Macbook Air and Macbook Pros have also experienced this periodically.)
Another strange thing, is that there is this one particular WIFI network at work, that I've successfully connected to before, upon return the next time, all of a sudden, the network isn't even visible anymore. My OS5 iPhone sees it fine, and never has a problem, but repeatedly this happens. Other people at work who also use Macbook Pro and Macbook Air also encounter the same problem. People who are using PCs don't have the same experience.
Is there a setting somewhere? I have "Remember networks this computer has joined" checked, and I see the particular network listed as ones I've joined.
Any light that can be shed on this would be greatly appreciated. It's very frustrating, especially Airs don't have a built-in ethernet port. I hate using the adapter, it steals one of my USB slots.
Thank you in advance!

Hi sashton,
When troubleshooting Wi-Fi connectivity issues, I find the following resource has the most relevant information:
Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6
http://support.apple.com/kb/HT4628
Furthermore, you may want to avoid giving your network a common name. While the following article (and excerpt) refer to iOS devices, the same applies for your Mac:
Avoid giving your wireless network a common name (SSID)
http://support.apple.com/kb/HT4450
If you were to give your wireless network a common name (SSID), users of your network who use iOS devices [sic] and are away from your network would run the risk of joining a different network with the same name. Having joined the unexpected network, they would be exposed to potential data theft.
Because of this security issue, Apple maintains a list of common or ambiguous SSIDs, including the default SSID for many commercially available access points, as well as the SSIDs "wireless" and "default". If your network's name is on the list, any iOS device [sic] that joins the network stores the access point's BSSID and associates it with the network's SSID. Subsequently, it will only auto-join the network if the access point's BSSID matches the information the device has stored. This avoids joining a different network with the same name.
Therefore, you may want to refer to the following article when configuring your Wi-Fi router:
iOS and OS X: Recommended settings for Wi-Fi routers and access points
http://support.apple.com/kb/HT4199
Thanks,
Matt M.

UWL COnfiguration(Connecters is not successfully connected)

Similar Messages

Maybe you are looking for