V240 and ALOM network card

Hi everyone,
Well, we got a problem with that network ALOM card ... :-/
We defined it quite well, IP adress and all the easy stuffs but we can't ping it !
We tried to connect by the serial port and it was ok. Our cables are good and the switch is a 10Mb one. Btw, it happens on 4 of our servers and 6 other SUN V240 servers (connected on the same switch) works good !
We simply don't understand what goes wrong ... what did we missed ?
Tx for any help =)

Ok, we got it ! :-/
That was trivious ... the 4 servers were connected to a separate hub ! and a $%*�� just took the network cable relaying the two hubs <img src="images/smiley_icons/icon_sad.gif" border=0 alt="Sad">
Anyway, the problem is solved and if you got the same trick : have a GOOD look of your cables before posting like me ! <img src="images/smiley_icons/icon_wink.gif" border=0 alt="Wink">
Silly me.
@+, Burzuum

Similar Messages

Problems with SRW224G4 switch and Bridged Network Cards

Hello,
We have recently installed a SRW224G4 switch and have discovered that when we plug our DELL PowerEdge 2900 server into the switch, the switch loses all network connectivity and all of the LED's on the switch start flashing.
The server works perfectly well plugged into another switch, but as soon as we introduce the SRW224G4 into the network, either with the server plugged into that switch or any other, the problem re-occurs.
The only way we found we could eliminate this issue was if we disabled the Bridged Network connection on the two network cards on the server. If we do that, everything is fine, except the network performance of the server has dropped significantly.
The server is plugged into the 1GB ports on the switch, although we tried it on the 100MB ports and received the same problems. The switch reports that the ports are running at full-duplex.
Has anyone noticed this behavior before, and more importantly been able to rectify it.
Thanks in advance for your assistance,
Paul

I had this problem as well with any Linksys 2024 or rackmountable switch.. The trick is, you need to use the network cards management software to "team" or bridged the 2 NIC's otherwise the switch detects a loop and the whole thing locks up. So lame... Windows built in bridge mode stinks dont use it. When you use the Intel management software or Dell or HP's NIc management software you have the option to actually choose "redundant mode" where you can pick a Nic to be the primary, or you can choose Load Balancing where you can essentially double your throughput by joining the 2 nics.
In Windows 2008 Server, you actually do this by going to the Properties on the NIC in Device Manger. the software controls are now built right into the driver. pretty neat. 2003 you can check Device Manager the same way but not sure if it's the same as 2008, you might need to run the actual NIC management app.
Hope this helps
fdigi

I believe iMac is freezing because of interference between my Wifi/router combo unit and my Network Card. What should I do?

My mid-2010 iMac (Snow Leopard) has been freezing with a spinning wheel within 10 minutes of startup for about a week. I can only force it to shut down by holding the power button - nothing else functions at that point.
I've been to the Genius Bar 3 times, with no findings. They did an overnight diagnostic, and found nothing wrong. They reinstalled Mac OS X, and before I even restored, it was still misbehaving. I can't recreate it at the Apple Store, but it does it without fail at home. At length, I believe I've narrowed it down to the Wifi/router combo unit and the iMac network card. When I turn off the router (entirely or just "turn off" the wifi), it oeprates normally. If I turn off the ethernet (BOTH en 0 and en 1 - if either of them is on, I have problems), it operates normally. If I have them both on, it will freeze. What on earth?
It doesn't matter whether the iMac is actually CONNECTED by wifi or ethernet. Merely having them both TURNED ON is enough to cause the freezing. Has anyone heard of this? I can't seem to find anything on it. My only recourse seems to be asking my DSL provider for a new router and seeing if that helps.
Any other suggestions? Thanks!

I can't recreate it at the Apple Store, but it does it without fail at home.
That's because when troubleshooting no devices should be connected except for the keyboard.
You seem to have narrowed it down to your router. Suggest that you call the router manufacturer to find out what the problem is. If the router came from your ISP, call their tech support dept.

Sleep and Wireless network card

After waking from sleep the MacBook Pro is unable to connect to the internet. Network card is unable to get a signal and results in 169 address. Its ironic that to remidy this requires a reboot. So basicly sleep is not an option.
The router is a linksys wireless N. OS is Leopard. Other wireless devices do not suffer this problem.
Does anyone else experience this or is it something to do with the network card?
Message was edited by: rebelyell_

Hi and welcome check Fn-F5 Menu softswitch ...
regards KalvinKlein
Thinkies 2x X200s/X301 8GB 256GB SSD @ Win 7 64
Ideas Centre A520 ,Yoga 2 256GB SSD,Yoga 2 tablet @ Win 8.1

Beginner setting up solaris 10 container and having network card problems

Hi I am just learning about solaris containers and am having an issue of getting my new zone to be seen on the network.
I have installed the global zone server name GPSAPP02 network address of 192.168.200.45 works fine.
I created :-
a pool called "ellipse-pool" using pooladm/poolcfg
a zone called "ellipse-zone" using zoneadm/zonecfg
I used the followijng commands...
zoneadm list -cv
zonecfg -z ellipse-zone
create               --
set zonepath=/zfspool/zones/ellipse-zone
set autoboot=true
     add net
set address=192.168.200.46/24
set physical=eri0
set defrouter=192.168.200.254
end
set pool=ellipse-pool
verify
commit
exit
The output from the "zonecfg -z ellipse-zone info" command is below:-
zonename: ellipse-zone
zonepath: /zfspool/zones/ellipse-zone
brand: native
autoboot: true
bootargs:
pool: ellipse-pool
limitpriv:
scheduling-class:
ip-type: shared
inherit-pkg-dir:
dir: /lib
inherit-pkg-dir:
dir: /platform
inherit-pkg-dir:
dir: /sbin
inherit-pkg-dir:
dir: /usr
net:
address: 192.168.200.46/24
physical: eri0
defrouter not specified
I then installed the zone and rebooted using zoneadm.
I can login to the zone and setup the timezone and terminal etc.
I gave this a hostname of GPSEL01 as this is what I want it to be known as on the network.
So far so good but from the network I cannot ping the IP address I assigned to the zone 192.168.200.46
What have I missed or what should I check to troubleshoot this?
I ran a ifconfig -a and received the following information...
ifconfig -a
lo0:1: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
# ifconfig lo0:1 192.168.200.46 netmask 255.255.255.0 up
ifconfig: SIOCSLIFNETMASK: lo0:1: permission denied

Hi
I notice in your output from ifconfig -a in the global zone that the NIC card is nge1.
However in your zoneconfig you have set the NIC card to eri0 (physical = eri0). I cannot see this NIC card in your ifconfig -a.
When a zones is of IP-type shared-ip it needs to use a network interface that is already plumbed into the global zone. In your case you need to change the NIC in your zone config to nge1 :
zonecfg -z ellipse-zone
select net address=192.168.200.46
set physical=nge1
end
exit
Then reboot your zone.
A couple of other minor comments.
1) As it appears the zone is on the same subnet as the global zone, if the global zone already has the default route of 192.168.200.254 setup you don't need to specify it in the zone config. You are most likely to use the defrouter parameter if the zone was on a different subnet to the global zone (but shared the same physical NIC).
2) You have specified the netmask in the address field which is fine. But again this should not be necessary as long as your /etc/netmasks file is correct in the global zone.
Hope this helps

How to web filtering via two network cards?

I have Installed Server 2008 and two network cards
on my pc. One LAN card for clients access and one for internet router. I need to share internet connection to my client computers with
web filtering. So how to do that? I need to block some sites to client access.

Hi,
According to your description, my understanding is that you want to use the WS 2008 to share Internet connection and provide web filtering function for internal clients.
Internal clients –(NIC1) WS 2008(NIC2) – Internet router – Internet network
Manually assign IP address, default gateway, DNS server, etc. on NIC2. Manually assign IP address, DNS server, etc. on NIC1.
Install Network Policy and Access Services – Routing and Remote Access Services. Detailed steps reference:
Install and Enable the Routing and Remote Access Service
https://technet.microsoft.com/en-us/library/cc770798(v=ws.10).aspx
Then open Routing and Remote Access and start configuration. Enable NAT on NIC2 to transfer IP address. Detailed steps reference:
Enable and Configure NAT
https://technet.microsoft.com/en-us/library/dd469812.aspx
Windows Server itself does not support web-based filter, third-party tools with application-layer firewall might be needed to realize this function. Configure WS as a router, it supports IP packet filtering, which specifies which type of traffic is allowed
into and out of the router. Reference：
https://technet.microsoft.com/en-us/library/cc732746(v=ws.10).aspx
Best Regards,
Eve Wang
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Udev, two network cards

Hi!
I installed ARCH again. I didn't configure Xorg7 yet because I play with udev and my network cards. I have one integrated on the motherboard (3Com) which I use for Internet and I have D-Link card which I did use with my wifes computer and I live this card in for future. During installation was okay but after update I have a problem. Now I use a wifes computer and at this momemnt after sixt reboot network works.
How can i save this problem, please?
Mitja

lumiwa wrote:
Hi!
I installed ARCH again. I didn't configure Xorg7 yet because I play with udev and my network cards. I have one integrated on the motherboard (3Com) which I use for Internet and I have D-Link card which I did use with my wifes computer and I live this card in for future. During installation was okay but after update I have a problem. Now I use a wifes computer and at this momemnt after sixt reboot network works.
How can i save this problem, please?
Mitja
Some information more:
lsmod show me now when network works skge and sk98lin.
dmesg | grep etho:
skge eth0: addr....skge eth0: enabling interfaces
skge eth0: Link is up to 100 Mbps...
and on the end:
eth0: no IPv6 routers present

Installation CDs : which network card drivers are included ?

Hello,
I intend to install Arch on a laptop with Broadcom and Atheros network cards (LAN and Wifi).
I would like to check which network card drivers are present on the Arch installation CDs to check compliance with this laptop.
Where can grab this info ?
Thanks.
Bye,
Bruno

Thanks for attention.
The network cards present on my laptop (Acer Aspire 4750) are :
Network controller: Atheros Communications Inc. AR9287 Wireless Network Adapter (PC-Express) (rev 01)
Ethernet controller: Broadcom Corporation NetLink BCM57785 Gigabit Ethernet PCIe (rev 10)
I would like to check if the needed drivers (one or both) are included in the installations CDs (netinstall / core).
Bye,
Bruno

Network Card Configuration

Hi,
Could anybody tell me the command for configuring network card in Solaris 10. I installed Solaris 10 and my network card does not work any more. Thank you
OC.

The commands (logged in as root) are:
ifconfig network_card_name plumb
(Add the network card to the system if it has not been added to the system yet.)
ifconfig network_card_name ip_addr up
(Start the network card)
The configuration gets lost after re-booting the system.
To permanently add a network card to the system create the file
/etc/hostname.network_card_name
for example:
/etc/hostname.hme0
This file contains just one line. This line is a host name from /etc/hosts that corresponds to the IP address of the card.
The use of DHCP is a bit more complex:
Use DHCP once:
ifconfig network_card_name plumb
ifconfig network_card_name dhcp up
Use DHCP after re-boot:
Create /etc/hostname.network_card_name
Create /etc/dhcp.network_card_name
Leave both files empty.
Martin

Network card name switching.

Hello. I have a problem with NICs switching names. I followed Wiki and added 10-network.rules in /etc/udev/rules.d but it seems there is no effect.
/etc/udev/rules.d/10-network.rules
SUBSYSTEM=="net", ATTR{address}=="11:11:11:11:11:11", name="eth0"
SUBSYSTEM=="net", ATTR{address}=="00:11:11:11:11:11", name="eth1"
SUBSYSTEM=="net", ATTR{address}=="00:00:11:11:11:11", name="eth2"
MAC addresses have been hidden but the one in my config are correct.
I have 1 NIC onboard (eth0) and one network card with dual port (eth1,eth2).
Also what is the difference beteen ATTR{address} and ATTRS{address}?
Wiki mentions something about:
With a recent version of udev, this problem should be solved automatically thanks to the /usr/lib/udev/write_net_rules program which runs the 75-persistent-net-generator.rules script which produces a 70-persistent-net.rules.
I can't find any of those files.
Last edited by verb0ss (2012-06-14 17:09:16)

alphaniner wrote:
In my 10-network.rules, "name" is in all caps. Maybe that's your problem.
SUBSYSTEM=="net", ATTR{address}=="##:##:##:##:##:##", NAME="eth0"
SUBSYSTEM=="net", ATTR{address}=="##:##:##:##:##:##", NAME="eth1"
SUBSYSTEM=="net", ATTR{address}=="##:##:##:##:##:##", NAME="eth2"
SUBSYSTEM=="net", ATTR{address}=="##:##:##:##:##:##", NAME="eth3"
I haven't noticed such an obvious thing. I have corrected the config now and i will give it a few days to test it. Thx a lot mate.

Updated bios via Live Update and now my Network card isn't detected

I have an msi Z87-GD65 Gaming Motherboard and I updated some drivers and the bios via msi Live Update 6 last night and now my computer refuses to recognize my network adapter. The adapter is a TRENDnet N600, plugs into PCIe if I'm not mistaken. Wifi if my only option with this computer, I can't use ethernet, so it's really important I get the network card working again. I have had zero issues with it until this.
The reason I was updating was to try to get my third monitor to work when plugged into the mobo, while my other two were plugged into the graphics card (which I also installed yesterday, but it's working fine). Note that it still was not working, but I had enabled the IGD Multi-Monitor from bios.
Any suggestions would be appreciated. I did try uninstalling the drivers but it still won't detect the network card. I also tried disconnecting and reconnecting the network card (and I cleaned the port for good measure).
I've only been using Windows computers for a year, so bear with me if there's stuff I don't know. Thanks in advance. I can try to get a full list of what was installed later tonight, but all of it that I can find has been uninstalled at this point.
Note: I did not flash the bios when I installed, which I have now heard is a bad idea, apparently. l:

what OS you are running?
Quote
Note: I did not flash the bios when I installed, which I have now heard is a bad idea, apparently. l:
you said you've updated drivers & BIOS:
Quote
I updated some drivers and the bios via msi Live Update 6 last night and now my computer refuses to recognize my network adapter.
can you clarify is you update BIOS too or not?
and what is your current bios version?
Quote
and I updated some drivers
what kind of drivers?
Quote
I did try uninstalling the drivers but it still won't detect the network card. I also tried disconnecting and reconnecting the network card (and I cleaned the port for good measure).
have you tried to load last good known configuration or the last windows restore point?
or to reinstall OS?

HT3986 Where can i download the driver for my network card? i have a macbook pro mid 2012, and are using windows 7 ultimate

Where can i download the driver for my network card? i have a macbook pro mid 2012, and are using windows 7 ultimate

uhm hey guys,
idk where else to get help so ima try here,
i got windows 8 installed with bootcamp on my macbook pro late 2010 (5, 5) and theres no sound coming out of it, so i installed an nvidia audio driver (idk, it could be the incorrect one) but i have nvidia GeForce 320 on my macbook.
do you know what i should install ?
but when i go onto my osx the sound is fine, so i figured im missing something on windows 8
Orrrr could i just go out and get parallels and hope it doesn't get the same problems?

A question about Routers and network cards

I have a question, Can Hardware confict with internet speed problems with the routers like one having a gigabit etherenet network card and 1/100 intel etherent card?

Ethernet components are generally compatible across brand names, and speeds. So you can connect gigabit cards to 10/100 networks. You can connect 10/100 cards to gigabit networks.
When you mix speeds, you will be limited to the fastest speed that all components can do, so if you connect a gigabit card to a 10/100 network, you will be limited to a 100 Mbps connection.

Do i need a network card to install and run a local java web server

Friends,
Do i need a network card in my computer to install and run a local Java Web Server or any Web Server.

network cards are only for connecting equipment together... you can set up a webserver without any more equipment than you have already! Indeed Tomcat... BUT you would be better off with apache for production stuff. It depends what you need to serve... if its mainly static pages (i guess it probably isn't) then apache will be enough by itself; but if you need to serve dynamic pages (JSP, Servlet blah blah) then you will need tomcat. Tomcat has it's own webserver and its perfectly ok for testing or low-load stuff, but you can integrate with Apache (a moderately compex task, but do-able, see tomcat-user forum off of apache site) for greater stability, and you don't have to show the port in the URL... Don't set up a webserver on any pc that contains stuff you don't want hacked into... it becomes very succeptible when the service is up...

My network card goes to sleep and requires a reboot

I recently upgrade my MAC-Pro to OSX 10.9.
When my computer goes to sleep it seems my network card goes to sleep as well.
The computer comes back, but I have to restart to get my network card to work again.

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, or by corruption of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

V240 and ALOM network card

Similar Messages

Maybe you are looking for