V880 CPU timneout / dump errors
We have a V880 with 8x1.2GHz CPU's we just purchased.
And we are having some CPU problems.
On arrival CPU's 7 & 8 failed due to timeouts. We received a new RMA from Sun for a 2x1.2GHx mem/board.
Last night we had the same problem occur:
Complained about cpu3 and dumped���(panic[cpu3]/thread=3001b87d760: panic sync timeout
dumping to /dev/dsk/c1t0d0s1, offset 1718222848I) pulled that cpu module and the system was fine after that
Then overnight we had another problem:
Looks like our system rebooted last night due to a failure on cpu 5.
Dec 13 01:57:23 gandalf unix: [ID 836849 kern.notice]
Dec 13 01:57:23 gandalf ^Mpanic[cpu5]/thread=30015443080:
Dec 13 01:57:23 gandalf unix: [ID 127206 kern.notice] alloccgblk: can't find blk in cyl, pos:10, i:1985, fs:/ bno: b49
Dec 13 01:57:23 gandalf unix: [ID 100000 kern.notice]
Dec 13 01:57:23 gandalf genunix: [ID 723222 kern.notice] 000002a1008f0f50 ufs:real_panic_v+70 (0, 1047c140, 2a1008f11f0, 0
, 0, 0)
Dec 13 01:57:23 gandalf genunix: [ID 179002 kern.notice] %l0-3: 00000000101ffa24 0000000000000000 0000000000002000 00000
2a1008f1a00
Dec 13 01:57:23 gandalf %l4-7: 00000300159e92d8 0000030002c8cd88 0000000000002000 00000000ff23c008
Dec 13 01:57:23 gandalf genunix: [ID 723222 kern.notice] 000002a1008f1000 ufs:ufs_fault_v+c8 (3000017d230, 0, 2a1008f11f0,
300031e9e18, 5b, 0)
Dec 13 01:57:23 gandalf genunix: [ID 179002 kern.notice] %l0-3: 000003000017d180 000000001047c140 00000300159e9480 00000
300159e9420
Please advise if this may be due to a patch or hardware?
thanks
This is the diagnostic output from the test 880. This system only has 1 cpu module in it. This is the one that was sent as an rma replacement.
��
<*>
Hardware Power On
@(#)OBP 4.15.1 2004/06/02 16:06 Sun Fire 8XX
Front Panel Keyswitch is in Diagnostic position.
System is initializing in Service Mode.
Online: CPU0 CPU2*
Validating JTAG integrity...Done
Disabling DAR error circuitry...Done
Clearing DCS error circuitry state...Done
Initializing DTL circuitry state...Done
Initializing MDR via JTAG...Done
Enabling DAR error circuitry...Done
Probing core system FRUs..
Probing Motherboard....part# 501-6771-02 serial# 000406
Safari min 100MHz, cumulative 100MHz; max 150MHz, cumulative 150MHz
'STICK' clock 10MHz; BootBus timing 014f.99fd.a7e6.3f29
Probing I/O Board......part# 501-5142-17 serial# 035061
Probing System RSC.....part# 501-5856-06 serial# 267275
Probing PwrDistBoard...part# 375-0071-03 serial# N59035
Probing PowerSupply0...part# 300-1353-03 serial# M82973
Probing PowerSupply1...part# 300-1353-03 serial# M82974
Probing PowerSupply2...part# 300-1353-03 serial# M82971
Probing GPTwo Slot A...part# 501-6164-02 serial# 007739
Safari min 100MHz, cumulative 100MHz; max 150MHz, cumulative 150MHz
CPU rated speed 1200MHz; ECache 8MB 3.3ns
Probing GPTwo Slot B...No module detected
Probing GPTwo Slot C...No module detected
Probing GPTwo Slot D...No module detected Done
Desired Safari Bus speed 150MHz, selecting 150MHz
Configuring CPUs..........
... CPU0 Rated Speed 1200MHz, Safari 150MHz, want 8:1, got 8:1 ==> CPU 1200MHz
Ecache 8MB 3.3ns mode=5-4-4 2-way ECCR: 0000.0000.0343.4c00
... CPU2 Rated Speed 1200MHz, Safari 150MHz, want 8:1, got 8:1 ==> CPU 1200MHz
Ecache 8MB 3.3ns mode=5-4-4 2-way ECCR: 0000.0000.0343.4c00 Done
Setting system speed (and resetting)...
<*>
Set Speed Reset
@(#)OBP 4.15.1 2004/06/02 16:06 Sun Fire 8XX
Front Panel Keyswitch is in Diagnostic position.
System is initializing in Service Mode.
Online: CPU0 UltraSPARC III+ (v11.1) 8:1 1200MHz 8MB 4:1 ECache
Online: CPU2 UltraSPARC III+ (v11.1) 8:1 1200MHz 8MB 4:1 ECache <br />Executing POST w/%o0 = 0000.1000.0101.4043<br />0:0><br />0:0>@(#) Sun Fire[TM] V880/V890 POST 4.15.0 2004/05/27 13:23 <br /> /dat/fw/common-source/firmware_re/post/post-build-4.15.0/Cam elot/daktari/<br />integrated (firmware_re) <br />0:0>Copyright �� 2004 Sun Microsystems, Inc. All rights reserved<br /> SUN PROPRIETARY/CONFIDENTIAL.<br /> Use is subject to license terms.<br />0:0>Jump from OBP->POST.<br />0:0>diag-switch? configuration variable set TRUE.<br />0:0>Keyswitch in DIAGNOSTIC POSITION.<br />0:0>Diag level set to MAX.<br />0:0>Verbosity level set to MAX.<br />0:0>MFG scrpt mode set NORM <br />0:0>I/O port set to serial TTYA.<br />0:0><br />0:0>Start selftest...<br />0:0>CPUs present in system: 0:0 2:0<br />0:0>Test CPU(s).....<br />0:0>Init CPU<br />0:0> UltraSparc_III_plus Version 11.1<br />0:0>DMMU Registers Access<br />0:0>DMMU TLB DATA RAM Access<br />0:0>DMMU TLB TAGS Access<br />0:0>IMMU Registers Access<br />0:0>IMMU TLB DATA RAM Access<br />0:0>IMMU TLB TAGS Access<br />0:0>Probe Ecache<br />0:0> Size = 00000000.00800000...<br />0:0>Ecache Data Bitwalk<br />0:0>Ecache Address Bitwalk<br />0:0>Scrub and Setup Ecache<br />0:0>Setup and Enable DMMU<br />0:0>Setup DMMU Miss Handler<br />0:0>Test and Init Temp Mailbox<br />2:0>Init CPU<br />2:0> UltraSparc_III_plus Version 11.1<br />2:0>DMMU Registers Access<br />2:0>DMMU TLB DATA RAM Access<br />2:0>DMMU TLB TAGS Access<br />2:0>IMMU Registers Access<br />2:0>IMMU TLB DATA RAM Access<br />2:0>IMMU TLB TAGS Access<br />2:0>Probe Ecache<br />2:0> Size = 00000000.00800000...<br />2:0>Ecache Data Bitwalk<br />2:0>Ecache Address Bitwalk<br />2:0>Scrub and Setup Ecache<br />2:0>Setup and Enable DMMU<br />2:0>Setup DMMU Miss Handler<br />2:0>Test and Init Temp Mailbox<br />0:0>Init Scan/I2C.....<br />0:0>Initializing Scan Database<br />0:0>Mask DAR errors off<br />0:0>Init MDR DTL<br />0:0>Init DAR DTL<br />0:0>Enable Partial DAR error<br />0:0>Init DCS DTL<br />0:0>Init I2C<br />0:0>Unquiesce Safari<br />0:0>Margin all voltages to nominal<br />0:0>Scan ring integrity<br />0:0><br />0:0>INFO: H/W under test = CPU Board Slot B (Cheetah 1, DCDS [0-7], SRAMs) Scan <br />Ring NOT Present or Shut OFF <br />0:0><br />0:0>INFO: H/W under test = CPU Board Slot B (Cheetah 3, SRAMs) Scan Ring NOT Pre<br />sent or Shut OFF <br />0:0><br />0:0>INFO: H/W under test = CPU Board Slot C (Cheetah 4, DCDS [0-7], SRAMs) Scan <br />Ring NOT Present or Shut OFF <br />0:0><br />0:0>INFO: H/W under test = CPU Board Slot D (Cheetah 5, DCDS [0-7], SRAMs) Scan <br />Ring NOT Present or Shut OFF <br />0:0><br />0:0>INFO: H/W under test = CPU Board Slot C (Cheetah 6, SRAMs) Scan Ring NOT Pre<br />sent or Shut OFF <br />0:0><br />0:0>INFO: H/W under test = CPU Board Slot D (Cheetah 7, SRAMs) Scan Ring NOT Pre<br />sent or Shut OFF <br />0:0>Set Trip Temp CPU 0 to 110C<br />0:0>Set Trip Temp CPU 2 to 110C<br />0:0>TUES DEC 13 11:48:56 GMT 5<br />0:0>Safari quick check<br />0:0> to IO-bridge_0 <br />0:0> to IO-bridge_1 <br />0:0>Safari full check<br />0:0> to IO-bridge_0 <br />0:0> to IO-bridge_1 <br />0:0>Disable CPU 0 error checking<br />0:0>Disable CPU 2 error checking<br />0:0>Basic Memory Test.....<br />0:0>Probe and Setup Memory<br />0:0>INFO: 512MB Bank 0<br />0:0>INFO: 512MB Bank 1<br />0:0>INFO: 512MB Bank 2<br />0:0>INFO: 512MB Bank 3<br />0:0><br />0:0>Data Bitwalk on Master<br />0:0> Test Bank 0.<br />0:0> Test Bank 1.<br />0:0> Test Bank 2.<br />0:0> Test Bank 3.<br />0:0>Address Bitwalk on Master<br />0:0><br />0:0>INFO: Addr walk mem test on CPU 0:0 Bank 0: 00000000.00000000 to 00000000.20<br />000000.<br />0:0><br />0:0>INFO: Addr walk mem test on CPU 0:0 Bank 1: 00000001.00000000 to 00000001.20<br />000000.<br />0:0><br />0:0>INFO: Addr walk mem test on CPU 0:0 Bank 2: 00000002.00000000 to 00000002.20<br />000000.<br />0:0><br />0:0>INFO: Addr walk mem test on CPU 0:0 Bank 3: 00000003.00000000 to 00000003.20<br />000000.<br />0:0>Set Mailbox<br />0:0>Setup Final DMMU Entries<br />0:0>Post Image Region Scrub<br />0:0>Run POST from Memory<br />0:0>Verifying checksum on copied image.<br />0:0>The Memory's CHECKSUM value is 2a78.<br />0:0>The Memory's Content Size value is a0654.<br />0:0>Success... Checksum on Memory Validated.<br />2:0>Safari quick check<br />2:0> to IO-bridge_0 <br />2:0> to IO-bridge_1 <br />2:0>Safari full check<br />2:0> to IO-bridge_0 <br />2:0> to IO-bridge_1 <br />2:0>Probe and Setup Memory<br />2:0>INFO: 512MB Bank 0<br />2:0>INFO: 512MB Bank 1<br />2:0>INFO: 512MB Bank 2<br />2:0>INFO: 512MB Bank 3<br />2:0><br />2:0>Set Mailbox<br />0:0>Data Bitwalk on Slave 2<br />0:0> Test Bank 0.<br />0:0> Test Bank 1.<br />0:0> Test Bank 2.<br />0:0> Test Bank 3.<br />0:0>Address Bitwalk on Slave 2<br />0:0><br />0:0>INFO: Addr walk mem test on CPU 2:0 Bank 0: 00000020.00000000 to 00000020.20<br />000000.<br />0:0><br />0:0>INFO: Addr walk mem test on CPU 2:0 Bank 1: 00000021.00000000 to 00000021.20<br />000000.<br />0:0><br />0:0>INFO: Addr walk mem test on CPU 2:0 Bank 2: 00000022.00000000 to 00000022.20<br />000000.<br />0:0><br />0:0>INFO: Addr walk mem test on CPU 2:0 Bank 3: 00000023.00000000 to 00000023.20<br />000000.<br />2:0>Setup Final DMMU Entries<br />2:0>Map Slave POST to master memory<br />2:0>8k DMMU TLB 0 Data<br />0:0>Full CPU Test.....<br />0:0>8k DMMU TLB 0 Data<br />2:0>8k DMMU TLB 1 Data<br />0:0>8k DMMU TLB 1 Data<br />2:0>8k DMMU TLB 0 Tags<br />0:0>8k DMMU TLB 0 Tags<br />2:0>8k DMMU TLB 1 Tags<br />0:0>8k DMMU TLB 1 Tags<br />2:0>8k IMMU TLB Data<br />0:0>8k IMMU TLB Data<br />2:0>8k IMMU TLB Tags<br />0:0>8k IMMU TLB Tags<br />2:0>Instruction Cache Tag RAM<br />0:0>Instruction Cache Tag RAM<br />2:0>Instruction Cache RAM<br />0:0>Instruction Cache RAM<br />2:0>I-Cache Valid/Predict TAGS Test<br />0:0>I-Cache Valid/Predict TAGS Test<br />2:0>I-Cache Branch Predict Array Test<br />0:0>I-Cache Branch Predict Array Test<br />2:0>Instruction Cache Snoop Tag Field<br />0:0>Instruction Cache Snoop Tag Field<br />2:0>Flush D/W caches<br />0:0>Flush D/W caches<br />2:0>Data Cache RAM<br />0:0>Data Cache RAM<br />2:0>Data Cache Tags<br />0:0>Data Cache Tags<br />2:0>Data Micro Tags<br />0:0>Data Micro Tags<br />2:0>D-Cache SnoopTags Test<br />0:0>D-Cache SnoopTags Test<br />2:0>WCache RAM<br />0:0>WCache RAM<br />2:0>WCache Tags<br />0:0>WCache Tags<br />2:0>W-Cache Valid bit Test<br />0:0>W-Cache Valid bit Test<br />2:0>W-Cache Bank valid bit Test<br />0:0>W-Cache Bank valid bit Test<br />2:0>W-Cache SnoopTAGS Test<br />0:0>W-Cache SnoopTAGS Test<br />2:0>Prefetch Cache RAM<br />0:0>Prefetch Cache RAM<br />2:0>Prefetch Cache Tags<br />0:0>Prefetch Cache Tags<br />2:0>P-Cache SnoopTags Test<br />0:0>P-Cache SnoopTags Test<br />2:0>P-Cache Status Data Test<br />0:0>P-Cache Status Data Test<br />2:0>Branch Prediction Initialization<br />0:0>Branch Prediction Initialization<br />2:0>Print Mem Config<br />2:0>Caches : Icache is ON, Dcache is ON, Wcache is ON, Pcache is ON.<br />2:0>Memory in non-interleave config:<br />2:0> Bank 0 512MB : 00000020.00000000 -> 00000020.20000000.<br />2:0> Bank 1 512MB : 00000021.00000000 -> 00000021.20000000.<br />2:0> Bank 2 512MB : 00000022.00000000 -> 00000022.20000000.<br />2:0> Bank 3 512MB : 00000023.00000000 -> 00000023.20000000.<br />0:0>Memory Block.....<br />0:0>Print Mem Config<br />0:0>Caches : Icache is ON, Dcache is ON, Wcache is ON, Pcache is ON.<br />0:0>Memory in non-interleave config:<br />0:0> Bank 0 512MB : 00000000.00000000 -> 00000000.20000000.<br />0:0> Bank 1 512MB : 00000001.00000000 -> 00000001.20000000.<br />0:0> Bank 2 512MB : 00000002.00000000 -> 00000002.20000000.<br />0:0> Bank 3 512MB : 00000003.00000000 -> 00000003.20000000.<br />2:0>Scrub Memory<br />0:0>Scrub Memory<br />2:0>Quick Block Mem Test<br />2:0>Quick Test 16777216 bytes at 00000020.00000000<br />0:0>Quick Block Mem Test<br />0:0>Quick Test 16777216 bytes at 00000000.00600000<br />0:0>40% Done...<br />2:0>Flush Caches<br />0:0>Flush Caches<br />2:0>Get code in ecache.<br />0:0>Get code in ecache.<br />0:0>IO-Bridge Tests.....<br />0:0>IO-Bridge unit 0 init test <br />0:0>IO-Bridge unit 1 init test <br />0:0>IO-Bridge unit 0 reg test <br />0:0>IO-Bridge unit 0 mem test <br />0:0>IO-Bridge unit 0 PCI DMA A test <br />0:0>IO-Bridge unit 0 PCI DMA B test <br />0:0>IO-Bridge unit 0 PCI merg test <br />0:0>IO-Bridge unit 0 PCI iommu test <br />0:0>IO-Bridge unit 0 PCI stc test <br />0:0>IO-Bridge unit 0 interrupt test <br />0:0>IO-Bridge unit 1 reg test <br />0:0>IO-Bridge unit 1 mem test <br />0:0>IO-Bridge unit 1 PCI DMA C test <br />0:0>IO-Bridge unit 1 PCI DMA D test <br />0:0>IO-Bridge unit 1 PCI merg test <br />0:0>IO-Bridge unit 1 PCI iommu test <br />0:0>IO-Bridge unit 1 PCI stc test <br />0:0>IO-Bridge unit 1 interrupt test <br />2:0>IO-Bridge unit 0 init test <br />2:0>IO-Bridge unit 0 reg test <br />2:0>IO-Bridge unit 0 mem test <br />2:0>IO-Bridge unit 0 PCI DMA test <br />2:0>IO-Bridge unit 0 PCI merg test <br />2:0>IO-Bridge unit 0 PCI iommu test <br />2:0>IO-Bridge unit 0 PCI stc test <br />2:0>IO-Bridge unit 0 interrupt test <br />2:0>IO-Bridge unit 1 init test <br />2:0>IO-Bridge unit 1 reg test <br />2:0>IO-Bridge unit 1 mem test <br />2:0>IO-Bridge unit 1 PCI DMA test <br />2:0>IO-Bridge unit 1 PCI merg test <br />2:0>IO-Bridge unit 1 PCI iommu test <br />2:0>IO-Bridge unit 1 PCI stc test <br />2:0>IO-Bridge unit 1 interrupt test <br />2:0>FPU Registers and Data Path<br />0:0>FPU Registers and Data Path<br />2:0>FPU Move Registers<br />0:0>FPU Move Registers<br />2:0>FSR Read/Write<br />0:0>FSR Read/Write<br />2:0>FPU Branch Instructions<br />0:0>FPU Branch Instructions<br />2:0>FPU Functional Test<br />0:0>FPU Functional Test<br />2:0>FPU BLOCK REG TEST<br />0:0>FPU BLOCK REG TEST<br />2:0>Calculating memory test time<br />0:0>Full Memory Test.....<br />2:0><br />2:0>INFO: The expected TIMEOUT for the block memory tests can exceed 2 minutes.<br />0:0>Calculating memory test time<br />2:0><br />2:0>INFO: The expected TIMEOUT for the MOVI memory tests can exceed 112 minutes.<br />0:0><br />0:0>INFO: The expected TIMEOUT for the block memory tests can exceed 2 minutes.<br />0:0><br />0:0>INFO: The expected TIMEOUT for the MOVI memory tests can exceed 112 minutes.<br />2:0>Block Memory<br />0:0>Block Memory<br />2:0>Test 536870912 bytes on bank 0....<br />0:0>Test 530579456 bytes on bank 0....<br />0:0>1% Done...<br />0:0>4% Done...<br />0:0>6% Done...<br />0:0>9% Done...<br />0:0>12% Done...<br />0:0>15% Done...<br />0:0>18% Done...<br />0:0>20% Done...<br />0:0>23% Done...<br />0:0>26% Done...<br />0:0>29% Done...<br />0:0>32% Done...<br />0:0>35% Done...<br />0:0>37% Done...<br />0:0>40% Done...<br />0:0>43% Done...<br />0:0>46% Done...<br />0:0>49% Done...<br />0:0>51% Done...<br />0:0>54% Done...<br />0:0>57% Done...<br />0:0>60% Done...<br />0:0>63% Done...<br />0:0>65% Done...<br />0:0>68% Done...<br />0:0>71% Done...<br />0:0>74% Done...<br />0:0>77% Done...<br />0:0>79% Done...<br />0:0>82% Done...<br />0:0>85% Done...<br />0:0>88% Done...<br />0:0>91% Done...<br />0:0>94% Done...<br />2:0>Test 536870912 bytes on bank 1....<br />0:0>96% Done...<br />0:0>99% Done...<br />0:0>Test 536870912 bytes on bank 1....<br />0:0>1% Done...<br />0:0>4% Done...<br />0:0>6% Done...<br />0:0>9% Done...<br />0:0>12% Done...<br />0:0>15% Done...<br />0:0>18% Done...<br />0:0>20% Done...<br />0:0>23% Done...<br />0:0>26% Done...<br />0:0>29% Done...<br />0:0>31% Done...<br />0:0>34% Done...<br />0:0>37% Done...<br />0:0>40% Done...<br />0:0>43% Done...<br />0:0>45% Done...<br />0:0>48% Done...<br />0:0>51% Done...<br />0:0>54% Done...<br />0:0>56% Done...<br />0:0>59% Done...<br />0:0>62% Done...<br />0:0>65% Done...<br />0:0>68% Done...<br />0:0>70% Done...<br />0:0>73% Done...<br />0:0>76% Done...<br />0:0>79% Done...<br />0:0>81% Done...<br />0:0>84% Done...<br />2:0>Test 536870912 bytes on bank 2....<br />0:0>87% Done...<br />0:0>90% Done...<br />2:0><br />2:0>WARNING: TEST = Block Memory<br />2:0>H/W under test = CPU0, All CPU0 Memory<br />2:0>MSG = Data or Instruction Access Error,<br /> Trap Type 00000000.00000063<br /> Trap PC ffffffff.f01213d0<br /> Trap Level 00000000.00000001<br /> AFSR 00000002.00000147<br /> AFAR 00000022.06330020<br />2:0>END_WARNING<br /><br />0:0>93% Done...<br />2:0> CE bit: Correctable system data ECC error<br />2:0><br /> Failed cache line data:<br />2:0> Address 00000022.06330000=00000000.00000000.<br />2:0> Address 00000022.06330008=00000000.00000000.<br />2:0> Address 00000022.06330010=00000000.00000000.<br />2:0> Address 00000022.06330018=00000000.00000000.<br />2:0> Address 00000022.06330020=00000000.00000000.<br />2:0> Address 00000022.06330028=00000000.00000000.<br />2:0> Address 00000022.06330030=00000000.00000000.<br />2:0> Address 00000022.06330038=00000000.00000000.<br />2:0> AFSR check after re-reading data:<br />2:0> No Errors in afsr reg<br />0:0>95% Done...<br />2:0><br />2:0>ERROR: TEST = Block Memory<br />2:0>H/W under test = CPU2 Bank 2 Dimm 0, J7900 side 2<br />2:0>Repair Instructions: Replace items in order listed by 'H/W under test' above<br />.<br />2:0>MSG = DIMM failure Bank 2 DIMM 0 Pin 87<br />2:0>END_ERROR<br /><br />0:0>98% Done...<br />2:0>Test 536870912 bytes on bank 3....<br />0:0>Test 536870912 bytes on bank 2....<br />0:0>1% Done...<br />0:0>4% Done...<br />0:0>6% Done...<br />0:0>9% Done...<br />0:0>12% Done...<br />0:0>15% Done...<br />0:0>18% Done...<br />0:0>20% Done...<br />0:0>23% Done...<br />0:0>26% Done...<br />0:0>29% Done...<br />0:0>31% Done...<br />0:0>34% Done...<br />0:0>37% Done...<br />0:0>40% Done...<br />0:0>43% Done...<br />0:0>45% Done...<br />0:0>48% Done...<br />0:0>51% Done...<br />0:0>54% Done...<br />0:0>56% Done...<br />0:0>59% Done...<br />0:0>62% Done...<br />0:0>65% Done...<br />0:0>68% Done...<br />0:0>70% Done...<br />0:0>73% Done...<br />0:0>76% Done...<br />0:0>79% Done...<br />0:0>81% Done...<br />0:0>84% Done...<br />0:0>87% Done...<br />0:0>90% Done...<br />0:0>93% Done...<br />0:0>95% Done...<br />0:0>98% Done...<br />0:0>Test 536870912 bytes on bank 3....<br />0:0>1% Done...<br />0:0>4% Done...<br />0:0>6% Done...<br />0:0>9% Done...<br />0:0>12% Done...<br />0:0>15% Done...<br />0:0>18% Done...<br />0:0>20% Done...<br />0:0>23% Done...<br />0:0>26% Done...<br />0:0>29% Done...<br />0:0>31% Done...<br />0:0>34% Done...<br />0:0>37% Done...<br />0:0>40% Done...<br />0:0>43% Done...<br />0:0>45% Done...<br />0:0>48% Done...<br />0:0>51% Done...<br />0:0>54% Done...<br />0:0>56% Done...<br />0:0>59% Done...<br />0:0>62% Done...<br />0:0>65% Done...<br />0:0>68% Done...<br />0:0>70% Done...<br />0:0>73% Done...<br />0:0>76% Done...<br />0:0>79% Done...<br />0:0>81% Done...<br />0:0>84% Done...<br />0:0>87% Done...<br />0:0>90% Done...<br />0:0>93% Done...<br />0:0>95% Done...<br />0:0>98% Done...<br />0:0><br />0:0>Motherboard/Centerplane Board Part Number: <br />0:0> 5016771-02-50<br />0:0>IO/Riser Board Part Number: <br />0:0> 5015142-17-50<br />0:0>CPUA Board Part Number: <br />0:0> 5016164-02-50<br />0:0>CPUB Board Part Number: <br />0:0><br />0:0>INFO: Unpopulated Slot <br />0:0>CPUC Board Part Number: <br />0:0><br />0:0>INFO: Unpopulated Slot <br />0:0>CPUD Board Part Number: <br />0:0><br />0:0>INFO: Unpopulated Slot <br />0:0>Enable Errors.....<br />0:0>Turn IO-Bridge 0 errors on<br />0:0>Turn IO-Bridge 1 errors on<br />0:0>Turn CPU 0 errors on<br />0:0>Turn CPU 2 errors on<br />0:0>Turn Module A DCDS errors on<br />0:0>Turn DCS errors on<br />0:0>Turn DAR errors on<br />0:0>Turn error traps on<br />0:0>ERROR:<br />0:0> POST toplevel status has the following failures:<br />0:0> CPU2 Memory Bank 2<br />0:0> POST failed the following devices on CPU 2:<br />0:0> Mem Bank2 DIMM0<br />0:0>END_ERROR<br /><br />0:0>POST: Return to OBP.<br /><br /><br />CPU0: System POST Completed<br /> Pass/Fail Status = ffff.ffff.ffff.ffff<br /> ESB Overall Status = ffff.fbff.ffff.ffff<br /><br /><br /><>
POST Reset
@(#)OBP 4.15.1 2004/06/02 16:06 Sun Fire 8XX
Front Panel Keyswitch is in Diagnostic position.
System is initializing in Service Mode.
Online: CPU0 UltraSPARC III+ (v11.1) 8:1 1200MHz 8MB 4:1 ECache
Online: CPU2 UltraSPARC III+ (v11.1) 8:1 1200MHz 8MB 4:1 ECache <br />Configuring CPUs..........<br />... CPU0 Rated Speed 1200MHz, Safari 150MHz, want 8:1, got 8:1 ==> CPU 1200MHz<br /> Ecache 8MB 3.3ns mode=5-4-4 2-way ECCR: 0000.0000.0343.4c00<br />... CPU2 Rated Speed 1200MHz, Safari 150MHz, want 8:1, got 8:1 ==> CPU 1200MHz<br /> Ecache 8MB 3.3ns mode=5-4-4 2-way ECCR: 0000.0000.0343.4c00 Done<br /><>
CPU Configuration Reset
@(#)OBP 4.15.1 2004/06/02 16:06 Sun Fire 8XX
Front Panel Keyswitch is in Diagnostic position.
System is initializing in Service Mode.
Online: CPU0 UltraSPARC III+ (v11.1) 8:1 1200MHz 8MB 4:1 ECache
Online: *CPU2 UltraSPARC III+ (v11.1) 8:1 1200MHz 8MB 4:1 ECache <br />Enabling system bus....... CPU0 CPU2 Done<br />Probing Memory............<br />Probing CPU0 memory configuration<br /> NGDIMM#0 part# 501-5401-02 serial# 239775, 128MB + 128MB, SC#0<br /> NGDIMM#1 part# 501-5401-02 serial# 210339, 128MB + 128MB, SC#0<br /> NGDIMM#2 part# 501-5401-02 serial# 269977, 128MB + 128MB, SC#0<br /> NGDIMM#3 part# 501-5401-02 serial# 259281, 128MB + 128MB, SC#0<br /> NGDIMM#4 part# 501-5401-02 serial# 285460, 128MB + 128MB, SC#0<br /> NGDIMM#5 part# 501-5401-02 serial# 241197, 128MB + 128MB, SC#0<br /> NGDIMM#6 part# 501-5401-02 serial# 239762, 128MB + 128MB, SC#0<br /> NGDIMM#7 part# 501-5401-02 serial# 207368, 128MB + 128MB, SC#0<br />Probing CPU2 memory configuration<br /> NGDIMM#0 part# 501-5401-02 serial# 306155, 128MB + 128MB, SC#0<br /> NGDIMM#1 part# 501-5401-02 serial# 241926, 128MB + 128MB, SC#0<br /> NGDIMM#2 part# 501-5401-02 serial# 236717, 128MB + 128MB, SC#0<br /> NGDIMM#3 part# 501-5401-02 serial# 277929, 128MB + 128MB, SC#0<br /> NGDIMM#4 part# 501-5401-02 serial# 267633, 128MB + 128MB, SC#0<br /> NGDIMM#5 part# 501-5401-02 serial# 266643, 128MB + 128MB, SC#0<br /> NGDIMM#6 part# 501-5401-02 serial# 210277, 128MB + 128MB, SC#0<br /> NGDIMM#7 part# 501-5401-02 serial# 284702, 128MB + 128MB, SC#0 Done<br />Initializing CPUs.........<br />Mungeing Memory...........Done<br />HiMem: 0000.00a0.8000.0000, size: 0000.0000.4000.0000<br />Configuring Memory........ CPU0 CPU2 Done<br />Init ICache/etc........... CPU0 CPU2 Done<br />Init ECache Tags.......... CPU0 CPU2 Done<br />Clearing TLBs............. CPU0 CPU2 Done<br />Setup I/DTLBs............. CPU0 CPU2 Done<br />Enabling Cache/MMUs....... CPU0 CPU2 Done<br />Init ECache Data.......... CPU0 CPU2 Done<br />Initializing boot memory..<br />Zeroing memory...Done<br />Copying FLASHRAM to memory...Verifying base 128KB...Done<br />Jumping into RAM (leaving slave CPUs in ROM)<br />RAM CRC = 0000.0000.64d5.d449; ROM CRC = 0000.0000.64d5.d449<br />Dropping in...<br />Find dropin, Decompressing Done, Size 0000.0000.0007.a830 (491KB)<br />Slave CPUs starting Forth at 0000.0000.f000.00e0 Done<br /><br />Boot CPU2 starting Forth at 0000.0000.f000.00e0<br /><br />Diagnostic console initialized<br />Probing gptwo at 0,0 SUNW,UltraSPARC-III+ (1200 MHz @ 8:1, 8 MB)<br /> memory-controller <br />Probing gptwo at 1,0 Nothing there<br />Probing gptwo at 2,0 SUNW,UltraSPARC-III+ (1200 MHz @ 8:1, 8 MB)<br /> memory-controller <br />Probing gptwo at 3,0 Nothing there<br />Probing gptwo at 4,0 Nothing there<br />Probing gptwo at 5,0 Nothing there<br />Probing gptwo at 6,0 Nothing there<br />Probing gptwo at 7,0 Nothing there<br />Probing gptwo at 8,0 pci pci <br />Probing gptwo at 9,0 pci pci <br />Probing gptwo at 10,0 Nothing there<br />Probing gptwo at 11,0 Nothing there<br />Probing gptwo at 12,0 Nothing there<br />Probing gptwo at 13,0 Nothing there<br />Probing gptwo at 14,0 Nothing there<br />Probing gptwo at 15,0 Nothing there<br />Probing gptwo at 16,0 Nothing there<br />Probing gptwo at 17,0 Nothing there<br />Loading Support Packages: kbd-translator obp-tftp SUNW,i2c-ram-device <br /> SUNW,fru-device <br />Loading onboard drivers: ebus flashprom bbc power i2c fru fru fru fru <br /> fru fru fru fru fru fru fru fru fru fru fru fru fru fru fru i2c <br /> controller smbus-ara controller temperature temperature ioexp adio <br /> adio ioexp ioexp ioexp ioexp ioexp ioexp ioexp adio adio adio adio <br /> temperature-sensor fru fru fru fru fru fru rscrtc hotplug-controller <br /> hotplug-controller hotplug-controller hotplug-controller bbc i2c i2c <br /> nvram idprom rtc gpio pmc rsc-control rsc-console serial <br />Setting NVRAM parameters to default values.<br />Memory Configuration: <br />CPU0 Bank0 128 + 128 + 128 + 128 : 512MB @ a080000000 2-way #0<br />CPU0 Bank1 128 + 128 + 128 + 128 : 512MB @ a000000000 4-way #0<br />CPU0 Bank2 128 + 128 + 128 + 128 : 512MB @ a080000000 2-way #1<br />CPU0 Bank3 128 + 128 + 128 + 128 : 512MB @ a000000000 4-way #2<br />CPU2 Bank0 128 + 128 + 128 + 128 : Not in Use <br />CPU2 Bank1 128 + 128 + 128 + 128 : 512MB @ a000000000 4-way #1<br />CPU2 Bank2 128 + 128 + 128 + 128 : Not in Use [Failed POST diagnostics]<br />CPU2 Bank3 128 + 128 + 128 + 128 : 512MB @ a000000000 4-way #3<br />Probing /<a href="mailto:pci@8" target="_blank">pci@8</a>,600000 Device 1 network <br />Probing /<a href="mailto:pci@8" target="_blank">pci@8</a>,600000 Device 2 SUNW,qlc fp disk <br />Probing /<a href="mailto:pci@8" target="_blank">pci@8</a>,700000 Device 1 scsi disk tape <br />Probing /<a href="mailto:pci@8" target="_blank">pci@8</a>,700000 Device 2 Nothing there <br />Probing /<a href="mailto:pci@8" target="_blank">pci@8</a>,700000 Device 3 Nothing there <br />Probing /<a href="mailto:pci@8" target="_blank">pci@8</a>,700000 Device 4 Nothing there <br />Probing /<a href="mailto:pci@8" target="_blank">pci@8</a>,700000 Device 5 Nothing there <br />Probing /<a href="mailto:pci@9" target="_blank">pci@9</a>,600000 Device 1 Nothing there <br />Probing /<a href="mailto:pci@9" target="_blank">pci@9</a>,600000 Device 2 Nothing there <br />Probing /<a href="mailto:pci@9" target="_blank">pci@9</a>,700000 Device 1 network usb <br />Probing /<a href="mailto:pci@9" target="_blank">pci@9</a>,700000 Device 2 Nothing there <br />Probing /<a href="mailto:pci@9" target="_blank">pci@9</a>,700000 Device 3 Nothing there <br />Probing /<a href="mailto:pci@9" target="_blank">pci@9</a>,700000 Device 4 Nothing there <br /><br />screen not found.<br />keyboard not found.<br />Keyboard not present. Using ttya for input and output.<br />Probing gptwo at 0,0 SUNW,UltraSPARC-III+ (1200 MHz @ 8:1, 8 MB)<br /> memory-controller <br />Probing gptwo at 1,0 Nothing there<br />Probing gptwo at 2,0 SUNW,UltraSPARC-III+ (1200 MHz @ 8:1, 8 MB)<br /> memory-controller <br />Probing gptwo at 3,0 Nothing there<br />Probing gptwo at 4,0 Nothing there<br />Probing gptwo at 5,0 Nothing there<br />Probing gptwo at 6,0 Nothing there<br />Probing gptwo at 7,0 Nothing there<br />Probing gptwo at 8,0 pci pci <br />Probing gptwo at 9,0 pci pci <br />Probing gptwo at 10,0 Nothing there<br />Probing gptwo at 11,0 Nothing there<br />Probing gptwo at 12,0 Nothing there<br />Probing gptwo at 13,0 Nothing there<br />Probing gptwo at 14,0 Nothing there<br />Probing gptwo at 15,0 Nothing there<br />Probing gptwo at 16,0 Nothing there<br />Probing gptwo at 17,0 Nothing there<br />Loading Support Packages: kbd-translator obp-tftp SUNW,i2c-ram-device <br /> SUNW,fru-device <br />Loading onboard drivers: ebus flashprom bbc power i2c fru fru fru fru <br /> fru fru fru fru fru fru fru fru fru fru fru fru fru fru fru i2c <br /> controller smbus-ara controller temperature temperature ioexp adio <br /> adio ioexp ioexp ioexp ioexp ioexp ioexp ioexp adio adio adio adio <br /> temperature-sensor fru fru fru fru fru fru rscrtc hotplug-controller <br /> hotplug-controller hotplug-controller hotplug-controller bbc i2c i2c <br /> nvram idprom rtc gpio pmc rsc-control rsc-console serial <br />Setting NVRAM parameters to default values.<br />Memory Configuration: <br />CPU0 Bank0 128 + 128 + 128 + 128 : 512MB @ a080000000 2-way #0<br />CPU0 Bank1 128 + 128 + 128 + 128 : 512MB @ a000000000 4-way #0<br />CPU0 Bank2 128 + 128 + 128 + 128 : 512MB @ a080000000 2-way #1<br />CPU0 Bank3 128 + 128 + 128 + 128 : 512MB @ a000000000 4-way #2<br />CPU2 Bank0 128 + 128 + 128 + 128 : Not in Use <br />CPU2 Bank1 128 + 128 + 128 + 128 : 512MB @ a000000000 4-way #1<br />CPU2 Bank2 128 + 128 + 128 + 128 : Not in Use [Failed POST diagnostics]<br />CPU2 Bank3 128 + 128 + 128 + 128 : 512MB @ a000000000 4-way #3<br />Probing /<a href="mailto:pci@8" target="_blank">pci@8</a>,600000 Device 1 network <br />Probing /<a href="mailto:pci@8" target="_blank">pci@8</a>,600000 Device 2 SUNW,qlc fp disk <br />Probing /<a href="mailto:pci@8" target="_blank">pci@8</a>,700000 Device 1 scsi disk tape <br />Probing /<a href="mailto:pci@8" target="_blank">pci@8</a>,700000 Device 2 Nothing there <br />Probing /<a href="mailto:pci@8" target="_blank">pci@8</a>,700000 Device 3 Nothing there <br />Probing /<a href="mailto:pci@8" target="_blank">pci@8</a>,700000 Device 4 Nothing there <br />Probing /<a href="mailto:pci@8" target="_blank">pci@8</a>,700000 Device 5 Nothing there <br />Probing /<a href="mailto:pci@9" target="_blank">pci@9</a>,600000 Device 1 Nothing there <br />Probing /<a href="mailto:pci@9" target="_blank">pci@9</a>,600000 Device 2 Nothing there <br />Probing /<a href="mailto:pci@9" target="_blank">pci@9</a>,700000 Device 1 network usb <br />Probing /<a href="mailto:pci@9" target="_blank">pci@9</a>,700000 Device 2 Nothing there <br />Probing /<a href="mailto:pci@9" target="_blank">pci@9</a>,700000 Device 3 Nothing there <br />Probing /<a href="mailto:pci@9" target="_blank">pci@9</a>,700000 Device 4 Nothing there <br /><br /><br />Sun Fire 880, No Keyboard<br />Copyright 1998-2004 Sun Microsystems, Inc. All rights reserved.<br />OpenBoot 4.15.1, 3072 MB memory installed, Serial #53196234.<br />Ethernet address 0:3:ba:2b:b5:ca, Host ID: 832bb5ca.<br /><br /><br /><br />Creating CPU memory layout properties.<br /><br /><br />Running diagnostic script obdiag/normal<br /><br />Testing /<a href="mailto:pci@8" target="_blank">pci@8</a>,600000/<a href="mailto:network@1" target="_blank">network@1</a><br />Subtest pci-config-reg-test<br />Subtest gem-enet-soft-reset-test<br />Subtest gem-txmc-soft-reset-test<br />Subtest gem-rxmc-soft-reset-test<br />Subtest global-config-reg-test<br />Subtest global-int-mask-reg-walk1-test<br />Subtest gem-txmc-soft-reset-test<br />Subtest tx-configuration-reg-read-test<br />Subtest tx-fifo-wr-ptr-reg-read-test<br />Subtest tx-fifo-rd-ptr-reg-read-test<br />Subtest tx-fifo-pkt-cntr-reg-read-test<br />Subtest tx-data-ptrl-reg-read-test<br />Subtest tx-data-ptrh-reg-rea
Similar Messages
-
Dump error while creating a new page in smartforms URGENT pls!!!
while creating a new page it is showing me a dump error , that the superior program execption was not intercepted , i have even given the next page field also correctly, i have attached a mainwindow to that page and a text element to that . .
thanks
sridharHi Deena,
This error:
"[2012-07-10T14:50:30.005+05:30] [wls_ods1] [ERROR] [] [oracle.adfinternal.view.faces.config.rich.RegistrationConfigurator] [tid: [ACTIVE].ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning)'] [userId: <anonymous>] [ecid: 0000JXkC9dU3FClqwsJb6G1FyhO000003D,0] [APP: odsm#11.1.1.2.0] Server Exception during PPR, #7[[
javax.servlet.ServletException: Could not initialize class com.octetstring.vde.admin.services.client.VDEAdminServiceSoapBindingStub"
is known issue
Go to metalink, article: Unable To Connect To OVD 11g Webinterface Using ODSM. [ID 1282757.1]
You need to apply that patch.
I hope this helps,
Thiago Leoncio. -
What is the purpose of short dump error report generated by the system? What r the major parts/section of this report?
hi please look through this:
Whenever any transaction or any process is executed it hits an ABAP code.
If there is any issue in executing the code the situation is called "ABAP DUMP" or 'Short Dump'
Transaction ST22 is used to check any ABAP Dump within a given duration.
U can also fix the issue with the help of ABAP editor (Transaction Code SE38) if u r good with ABAP.
you can select back to the last 14 days if you are
running the SAP_REORG_ABAPDUMPS job (program RSSNAPDL) which deletes te
old ABAP dumps every day, possibly further if you run it weekly or
monthly.
sap-basis sap-basisAll Groups Ignore this text box. It is used to detect spammers.If you enter anything into this text box, no search results will be displayed.
SAP Groups > Technical-functional > sap-basis > Message
About This Group | Invite peers to join this group
<< Prev thread < Prev msg Next msg > Next thread >>
short dump----urgent
Reply from Keith Lewis on 5/2/2003 3:22:00 AM
Good explanation Joy, but it is not only limited to the current day and
yesterday. If you click on the Selection button you can select previous
days as well. In fact you can select back to the last 14 days if you are
running the SAP_REORG_ABAPDUMPS job (program RSSNAPDL) which deletes te
old ABAP dumps every day, possibly further if you run it weekly or
monthly.
Cheers
Keith
SAP R/3 Support Specialist
Information Services International
Tel +44 1664 41 6178 Mobile +44 7887 627818
E-mail email@removed
Archive Page - http://www.ittoolbox.com//I/sap-r3-basis.asp
Dear sreenivas
If you receive an error message in the R/3 System log (SM21), or if you
see
a terminated update in the update service analysis transaction (SM13), or
DB
realated error ,check for dumps using the dump analysis transaction
(transaction ST22), or choose Tools -> Administration -> Monitoring ->
Dump
analysis.
Transaction ST22 enables you to analyze short dumps from the current and
previous day.
The dump analysis function shows you:
What happened
What you can do
How to correct the error
The dump analysis function also provides an error ID and keywords that you
can use to search in SAPNet, as well as information about:
The system environment
Users and transactions
Transaction ST22 enables you to analyze the following data:
Date, time, user, client
Contents of system and data fields
Contents of internal tables and application tables
ST22 is a very nice feature in SAP. This is where all the system errors
and users mistakes showed up. If there is a problem that you cannot
solve and you contact SAP support, they look at this area to analyze it.
This gives us lead where to handle the problems.
Error analysis
How to correct the error
System environment
User, transaction...
Information on where termination occurred
Contents of system fields
Chosen variables
Active calls / events
Internal notes
Active calls in SAP kernel
List of ABAP programs affected
List of internal tables
Directory of application tables (contents)
Directory of data areas (administration information)
Directory of data areas (contents)
ABAP control blocks CONT
End of runtime analysis
i think this would be helpful
regards
sravani -
Hi Everyone,
I'm loading 690k odd records to cube
I am facing short dump error while data request is processed to cube.
In ST22 i'm getting Timeout Error.
Buffer time is set for 10mins to process
Can anyone guide me in this issue.
Thanks in advanceHi,
Due to data volume your load took more than 7hrs. in general time out time is 7hrs. so in your case its may exceeded.
Try to increase time out time for your info package.
Go to your info pack--> menu scheduler --> time out time--> increase 7 hrs to 14hrs and trigger your load again. if its full load delete failed load and retrigger.
Thanks -
Short dump error when using count(*)
Hi Experts
I am getting a short dump error when selecting the records >= current date - 30 see the coding and comment please correct the coding I want to know the ztable records it is important for command interface.
I have 1402345 records available after deleting the records but as the memory is not enough it is giving short dump error
select count(*) from ZINT_TABLE
select count(*) from ZINT_MSGS
select * from zint_data
nto table izint_d2 . "PACKAGE SIZE 20000
where STATUS = 'OK' AND CREATED_ON >= w_date1. " VALUE
endselect.**
report z_eslp_command_records.
data: cnt type i.
data: cnt2 type i.
data: cnt3 type i.
data: cnt4 type i.
DATA:
w_date1 like sy-datum .
DATA:
w_date2 like sy-datum.
data: izint_msgs type table of zint_msgs.
data: izint_data type table of zint_data.
data: izint_m2 type table of zint_msgs.
data: izint_d2 type table of zint_data.
INITIALIZATION.
w_date1 = sy-datum - 30.
w_date2 = sy-datum - 30.
select * from zint_data
into table izint_data PACKAGE SIZE 3000
where STATUS = 'OK' AND CREATED_ON <= w_date1. " ZERO
endselect.
select * from zint_msgs
into table izint_msgs PACKAGE SIZE 3000
where CREATED_ON <= w_date2. " ZERO
endselect.
select * from zint_data
into table izint_d2 PACKAGE SIZE 20000
where STATUS = 'OK' AND CREATED_ON >= w_date1. " VALUE
endselect.
select * from zint_msgs
into table izint_m2 PACKAGE SIZE 20000
where CREATED_ON >= w_date2. " VALUE
endselect.
select * from zint_data
into table izint_data2
where STATUS = 'OK' AND CREATED_ON >= CONVERT(CHAR(8), GETDATE() - 30, 112)).
ENDSELECT.
select * from zint_msgs
into table izint_msgs2
where CREATED_ON >= CONVERT(CHAR(8), GETDATE() - 30, 112)).
ENDSELECT.
sort izint_data by created_on ascending.
sort izint_msgs by created_on ascending.
sort izint_d2 by created_on ascending.
sort izint_m2 by created_on ascending.
describe table izint_data lines cnt.
describe table izint_msgs lines cnt2.
describe table izint_d2 lines cnt3.
describe table izint_m2 lines cnt4.
write:/ ' Note: THE RECORDS COUNTED SHOULD SHOW ZERO ELSE THE SCRIPT FAILED TO RUN' color 3.
skip.
write:/ '1. Records counted in ZINT_DATA <=current date - 30 :' color 2, cnt color 4.
write:/ '2. Records available in ZINT_DATA >=current date - 30 'color 4, cnt3 color 4 .
skip.
write:/ '2. Records counted in ZINT_MSGS <=current date - 30 :' color 2 , cnt2 color 4.
write:/ '4. Records available in ZINT_MSGS >=current date - 30 'color 4 , cnt4 color 4 .
TOP-OF-PAGE.
WRITE:/55(60) ' WAGNERS INVESTMENT LIMITED '.
WRITE:/50(40) ' Command Interface Data' CENTERED .
WRITE:/50(40) '----
' CENTERED .
FORMAT INTENSIFIED ON.
SKIP.
"FORMAT COLOR COL_HEADING.
ULINE.
FORMAT COLOR 1.
END-OF-PAGE.Answer
-
Getting a program Dump Error in Herarchial ALV
Hello All,
I am getting a dump error when I am executing the below program. Kindly help as I am not getting the output. However all the subroutines are getting properly populated with data. Getting a dump error while calling the function : REUSE_ALV_HIERSEQ_LIST_DISPLAY
Pasted below are both the question and solution. Copy the solution in SE38 and execute it to check out the dump error.
Kindly help.
Thanks,
Vinod.
QUESTION :-
Objective
Hierarchical ALV for displaying Sales documents per customer
Design
Create a program that will allow the user to display all customers that have placed Sales Orders in the given date range. The user will have an ability to drill-down to see the sales order items per customer.
Selection screen fields
Sales order creation date (range)
Customer number (range)
Output
Header
Customer Number
Customer Name
Total Order value (sum of order values from items below)
Details
Sales order number
Material number
Order quantity
Order value
Reference
Tables: KNA1, VBAK, VBAP
Transaction VA03 (Sales order)
SOLUTION :-
*& Report Z_HALV_32722 *
REPORT Z_HALV_32722 .
TYPE-POOLS: slis.
TABLES : kna1,
vbak.
SELECT-OPTIONS: s_cst_no FOR kna1-kunnr.
SELECT-OPTIONS: s_cr_dt FOR vbak-erdat.
DATA : BEGIN of ty_hdr,
kunnr TYPE vbak-kunnr,
name1 TYPE kna1-name1,
netwr TYPE vbak-netwr,
END of ty_hdr,
gt_hdr LIKE TABLE OF ty_hdr,
gs_hdr LIKE LINE OF gt_hdr.
DATA : BEGIN of ty_ln,
kunnr TYPE vbak-kunnr,
vbeln TYPE vbap-vbeln,
matnr TYPE vbap-matnr,
kwmeng TYPE vbap-kwmeng,
netwr TYPE vbap-netwr,
END of ty_ln,
gt_ln LIKE TABLE OF ty_ln,
gs_ln LIKE LINE OF gt_ln.
DATA : BEGIN of ty_hdr1,
kunnr TYPE vbak-kunnr,
END of ty_hdr1,
gt_hdr1 LIKE TABLE OF ty_hdr1,
gs_hdr1 LIKE LINE OF gt_hdr1.
DATA : gt_fc TYPE slis_t_fieldcat_alv,
gs_fc LIKE LINE OF gt_fc,
gs_k_fld TYPE slis_keyinfo_alv,
gt_layout TYPE slis_layout_alv,
gv_repid TYPE sy-repid.
START-OF-SELECTION.
gv_repid = sy-repid.
perform fetch_data.
perform prepare_fc.
perform prepare_layout.
perform show_output.
*& Form fetch_data
text
--> p1 text
<-- p2 text
form fetch_data .
SELECT kunnr
INTO CORRESPONDING FIELDS OF TABLE gt_hdr1
FROM vbak
WHERE vbak~kunnr IN s_cst_no
AND vbak~erdat IN s_cr_dt.
DELETE ADJACENT DUPLICATES FROM gt_hdr1 COMPARING kunnr.
LOOP AT gt_hdr1 INTO gs_hdr1.
SELECT SINGLE vbakkunnr kna1name1 SUM( vbak~netwr )
INTO (gs_hdr-kunnr, gs_hdr-name1, gs_hdr-netwr)
FROM vbak INNER JOIN kna1
ON vbakkunnr = kna1kunnr
WHERE vbak~kunnr = gs_hdr1-kunnr
GROUP BY vbakkunnr kna1name1.
APPEND gs_hdr TO gt_hdr.
SELECT vbakkunnr vbapvbeln vbapmatnr vbapkwmeng vbap~netwr
INTO CORRESPONDING FIELDS OF TABLE gt_ln
FROM vbap INNER JOIN vbak
ON vbapvbeln = vbakvbeln
WHERE vbak~kunnr = gs_hdr1-kunnr.
ENDLOOP.
endform. " fetch_data
*& Form prepare_fc
text
--> p1 text
<-- p2 text
form prepare_fc .
CLEAR gs_k_fld.
gs_k_fld-header01 = 'KUNNR'.
gs_k_fld-item01 = 'KUNNR'.
CLEAR gs_fc.
gs_fc-fieldname = 'KUNNR'.
gs_fc-tabname = 'GT_HDR'.
gs_fc-seltext_l = text-001.
APPEND gs_fc TO gt_fc.
CLEAR gs_fc.
gs_fc-fieldname = 'NAME1'.
gs_fc-tabname = 'GT_HDR'.
gs_fc-seltext_l = text-002.
APPEND gs_fc TO gt_fc.
CLEAR gs_fc.
gs_fc-fieldname = 'NETWR'.
gs_fc-tabname = 'GT_HDR'.
gs_fc-seltext_l = text-003.
APPEND gs_fc TO gt_fc.
CLEAR gs_fc.
gs_fc-fieldname = 'VBELN'.
gs_fc-tabname = 'GT_LN'.
gs_fc-seltext_l = text-004.
APPEND gs_fc TO gt_fc.
CLEAR gs_fc.
gs_fc-fieldname = 'MATNR'.
gs_fc-tabname = 'GT_LN'.
gs_fc-seltext_l = text-005.
APPEND gs_fc TO gt_fc.
CLEAR gs_fc.
gs_fc-fieldname = 'KWMENG'.
gs_fc-tabname = 'GT_LN'.
gs_fc-seltext_l = text-006.
APPEND gs_fc TO gt_fc.
CLEAR gs_fc.
gs_fc-fieldname = 'NETWR'.
gs_fc-tabname = 'GT_LN'.
gs_fc-seltext_l = text-007.
APPEND gs_fc TO gt_fc.
endform. " prepare_fc
*& Form prepare_layout
text
--> p1 text
<-- p2 text
form prepare_layout .
gt_layout-colwidth_optimize = 'X'.
gt_layout-expand_fieldname = 'TST'.
endform. " prepare_layout
*& Form show_output
text
--> p1 text
<-- p2 text
form show_output .
CALL FUNCTION 'REUSE_ALV_HIERSEQ_LIST_DISPLAY'
EXPORTING
I_INTERFACE_CHECK = ' '
I_CALLBACK_PROGRAM = gv_repid
I_CALLBACK_PF_STATUS_SET = ' '
I_CALLBACK_USER_COMMAND = ' '
IS_LAYOUT = gt_layout
IT_FIELDCAT = gt_fc
IT_EXCLUDING =
IT_SPECIAL_GROUPS =
IT_SORT =
IT_FILTER =
IS_SEL_HIDE =
I_SCREEN_START_COLUMN = 0
I_SCREEN_START_LINE = 0
I_SCREEN_END_COLUMN = 0
I_SCREEN_END_LINE = 0
I_DEFAULT = 'X'
I_SAVE = ' '
IS_VARIANT =
IT_EVENTS =
IT_EVENT_EXIT =
i_tabname_header = 'GT_HDR'
i_tabname_item = 'GT_LN'
I_STRUCTURE_NAME_HEADER =
I_STRUCTURE_NAME_ITEM =
is_keyinfo = gs_k_fld
IS_PRINT =
IS_REPREP_ID =
I_BYPASSING_BUFFER =
I_BUFFER_ACTIVE =
IMPORTING
E_EXIT_CAUSED_BY_CALLER =
ES_EXIT_CAUSED_BY_USER =
tables
t_outtab_header = GT_HDR[]
t_outtab_item = GT_LN[]
EXCEPTIONS
PROGRAM_ERROR = 1
OTHERS = 2
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
endform. " show_outputEverything looks fine with the gt_layout, it is not an internal table, so no need to append to it, it is simply a structure, but you do tell it that TST is the expand field, but there is no field of this name in your internal for the header, so add it like this.
DATA : BEGIN of ty_hdr,
kunnr TYPE vbak-kunnr,
name1 TYPE kna1-name1,
netwr TYPE vbak-netwr,
<b>TST type c,</b>
END of ty_hdr,
Doing so should make you program work correctly.
Regards,
Rich Heilman
Message was edited by:
Rich Heilman -
Dump error when clicked on text elements in SAP Script window
Hi All,
There is an inclusion in SAP Script. I have written the code in driver program. I need to pass the value to SAP Script in the requested position. But when I go to SE71 > Form Name > Change or Display > MAIN Window > Text Elements > I get a dump error.
Category ABAP Programming Error
Runtime Errors DATA_LENGTH_TOO_LARGE
Except. CX_SY_RANGE_OUT_OF_BOUNDS
ABAP Program SAPLSTXK
Application Component BC-SRV-SCR
Date and Time 30.04.2014 20:00:08
Short text
Invalid partial field access: Length is too large
What happened?
Error in the ABAP Application Program
The current ABAP program "SAPLSTXK" had to be terminated because it has
come across a statement that unfortunately cannot be executed.
What can you do?
Note down which actions and inputs caused the error.
To process the problem further, contact you SAP system
administrator.
Using Transaction ST22 for ABAP Dump Analysis, you can look
at and manage termination messages, and you can also
keep them for a long time.
Error analysis
An exception occurred that is explained in detail below.
The exception, which is assigned to class 'CX_SY_RANGE_OUT_OF_BOUNDS', was not
caught in
procedure "TOKEN_COMMENT" "(FORM)", nor was it propagated by a RAISING clause.
Since the caller of the procedure could not have anticipated that the
exception would occur, the current program is terminated.
The reason for the exception is:
In the executed program "SAPLSTXK", the system attempted to access the field
"ITF_TOKEN" of the type "C" and with the length 255 using the length 272.
However, a partial field access with a length specification that is
larger than the field length is not allowed.
How to correct the error
Reduce the length used to access the field.
If the error occures in a non-modified SAP program, you may be able to
find an interim solution in an SAP Note.
If you have access to SAP Notes, carry out a search with the following
keywords:
"DATA_LENGTH_TOO_LARGE" "CX_SY_RANGE_OUT_OF_BOUNDS"
"SAPLSTXK" or "LSTXKFRN"
"TOKEN_COMMENT"
If you cannot solve the problem yourself and want to send an error
notification to SAP, include the following information:
1. The description of the current problem (short dump)
To save the description, choose "System->List->Save->Local File
(Unconverted)".
2. Corresponding system log
Display the system log by calling transaction SM21.
Restrict the time interval to 10 minutes before and five minutes
after the short dump. Then choose "System->List->Save->Local File
2937 * todo empty comment ???
2938 if g_tm_open eq true or " Section
2939 g_tm_b_close eq true.
2940 l_token = '\chcbpat0'.
2941 l_len = strlen( l_token ).
2942 token_control = true.
2943 assign l_token to <itf1>.
2944 perform put_itf1_new using l_len.
2945 perform token_line_begin changing l_next_token.
2946 else. " without section
2947 concatenate '\chcbpat0\line' g_cf_string l_cbpat_token into l_token.
2948 l_len = strlen( l_token ).
2949 token_control = true.
2950 assign l_token to <itf1>.
2951 perform put_itf1_new using l_len.
2952 endif.
2953 elseif l_next_token-code eq ')L'. " \par
2954 l_token = '\par'.
2955 l_len = strlen( l_token ).
2956 token_control = true.
2957 assign l_token to <itf1>.
2958 perform put_itf1_new using l_len.
2959 elseif l_next_token-code eq '(C' or " \par + format
2960 l_next_token-code eq ')C' or
2961 l_next_token-code eq '(&' or
2962 l_next_token-code eq 'TA' or
2963 l_next_token-code eq 'SC' or
2964 l_next_token-code eq 'ST'.
2965 concatenate '\chcbpat0\par' g_pf_string g_cf_string l_cbpat_token into l_token.
2966 l_len = strlen( l_token ).
>>>>> itf_token(l_len) = l_token.
2968 token_control = true.
2969 assign l_token to <itf1>.
2970 perform put_itf1_new using l_len.
2971 endif.
2972
2973 * Step 7: (L to disarm
2974 if g_compose eq true and
2975 l_next_token-code eq '(L'.
2976 perform read_next_itf_token(rstxscan) using p_token.
2977 endif.
2978
2979 ENDFORM. " token_comment
2980 *&---------------------------------------------------------------------*
2981 *& Form create_lang_info
2982 *&---------------------------------------------------------------------*
2983 * add default language to rtf
2984 *----------------------------------------------------------------------*
2985 * -->P_HEADER text
2986 * <--P_RESULT text
How do I open the text elements? I need to pass the variable inside SAP Script.
Please Help. The requirement is pending from very long. Not able to rectify this issue.
Regards,
RekhaHi,
There is a SAP Note about this problem
566794 - Runtime error: STRING_OFFSET_TOO_LARGE during conversion
Correction Instructions
Correction Instructions
Software Component
Valid from
Valid to
Number
SAP_BASIS
46B
46D
473267
SAP_BASIS
610
620
473185
Support Packages & Patches
Support Packages
Software Component
Release
Support Package
SAP_BASIS
46B
SAPKB46B48
46C
SAPKB46C39
46D
SAPKB46D28
610
SAPKB61027
620
SAPKB62014
Regards
Miguel -
Dump error while creating Invoicing document
Moderator note - this is the same problem as identified in thread Error is generated in Print workbench function ISU_INV_BILL_PREPARE. Thread locked and poster notified of rules violation.
Hi Experts,
I am new to ISU application.Please provide solution for below mentioned dump error.
The error is generated in Print workbench function ISU_INV_BILL_PREPARE which is called from application form IS_U_BILL (/1PWB/SAPL20020100218092657) when I'm trying to generate invoice for the bill in EASIBI.
Error analysis
Short text of error message:
Unexpected ELSE case: field sy-subrc with value 0 (/1PWB/200201002180926
57 )
Long text of error message:
Something has occurred in a CASE or IF construct which the
developer did not expect, or which is not permissible here.
System Response
Procedure
Note the field name and field value from the message as well as the
data pattern which lead to the error. Create a problem message.
Technical information about the message:
Message class....... "E9"
Number.............. 898
Variable 1.......... "sy-subrc"
Variable 2.......... 0
Variable 3.......... "/1PWB/20020100218092657"
| Variable 4.......... " "
Thanks in Advance.
Vaseem
Edited by: William Eastman on Mar 9, 2010 2:34 PM
Edited by: William Eastman on Mar 9, 2010 2:36 PMHi Experts,
Please reply..... It's very important.
Thanks
Vaseem
Moderator note: DO NOT beg for answers, or suggest that you need an immediate reply. Read the rules of engagement here Research Resources and Rules of Engagement
Edited by: William Eastman on Mar 9, 2010 2:24 PM -
I am getting dump error while running one report in one select query
Hi,
While running a report program, I am getting a dump error in one select query. So could you please correct the select query so that I can't face the dump error.
SELECT vbeln parvw kunnr INTO CORRESPONDING FIELDS OF TABLE l_t_vbpa
FROM vbpa
FOR ALL ENTRIES IN l_t_backorder_item
WHERE vbeln = l_t_backorder_item-vbeln AND
( ( parvw = c_we AND kunnr IN rng_shipto ) OR ( parvw = c_ag AND
kunnr IN rng_soldto ) ) .
<removed by moderator>
Best Regards,
BDP
Edited by: Thomas Zloch on Apr 30, 2010 12:31 PMHi Bansidhar,
It would be helpful if you could tell what type of dump it is.
If it is a timeout you should check whether l_t_backorder_item is empty - in this case ALL document numbers are selected. f you get the timeout with a populated table consider converting the l_t_backorder_item table into one ore more ranges tables - the select with ranges tables is way quicker than 'for all entries'. But take care the ranges table has not to many entries - the SAP SQL converter puts this into one huge SQL statement and this might become too big to be handled by the database (depends on the actual underlying database).
I would also consider splitting the SELECT into two (2nd one with 'appending into table') to make the code easier to understand It also helps the database system determining a strategy for the select.
Regards,
Gerd Rother -
Dump error while creating or double click the info package
Hello experts,
I have actived infocube 0FIAR_C03 in BI content. Ago, The creation infopackage have been deleted in the past , today, I created a infopackage, while I update mode selected u2018initialize delta processu2019, then click save button , the system prompt u2018Deltas already loaded for request REQU_D64R47LDUSZHY9CBIB86WMLFJ init.selection; no 2. initu2019, I canoti save it for my setting. Why is this?
Then I have search cause in SDN, and I have reference OSS Note 852443 to do .
Note 852443 have mention some table: RSSELDONE、RSSDLINIT、RSSDLINITSEL、ROOSPRMSC、ROOSPRMSF.
I have to delete that request of record using se16 in these tables: RSSELDONE、RSSDLINIT、RSSDLINITSEL.
in my BI 7.0 system, ROOSPRMSC、ROOSPRMSF is no any data.
I was no found delta queue in RSA7.
Now . Dump error while creating or double click the info package, how can I change this?
Please let me know the solution.
Thanks for your help.
Best Regards
SteveHere are some links which deals with same issue.
Re: Dump In Infopackage
Re: Getting into Short dump at the time of selecting InfoPackage to execute for
Short dump while performing init in infopackage
Re: Infopackage going into short dump
Thanks. -
Dump error after calling a global class from se24
this is the small code i did so far.
parameters: X type i,
Y type i.
data: Z type i.
data: con1 type ref to ZTEST1.
CALL METHOD con1->zm1
EXPORTING
a = x
b = y
IMPORTING
c = z.
write:/ z.
after executing iam getting a dump error-
An exception occurred that is explained in detail below.
The exception, which is assigned to class 'CX_SY_REF_IS_INITIAL', was not
caught and
therefore caused a runtime error.
The reason for the exception is:
You attempted to use a 'NULL' object reference (points to 'nothing')
access a component (variable: "CON1").
An object reference must point to an object (an instance of a class)
before it can be used to access components.
Either the reference was never set or it was set to 'NULL' using the
CLEAR statement.Hi, Could you please tell me how to solve this issue?
-
Short Dump error while loading data from R/3 to ODS
Hello,
while trying to load data into the ODS from R/3 I get the following short dump error message. How do I carry out step 1 in the below procedure. Where do i find the Activate Function. And idea?
Thanks,
SD
Diagnosis
Form routine CONVERT_ITAB_RFC is incorrect in transfer program
GP4C0LOLZ6OQ70V8JR365GWNW3K .
System Response
The IDoc processing was terminated and indicated as incorrect. The IDoc
can be reimported at any time.
Procedure
1. Go to the transfer rule maintenance for your InfoSource
ZFIN_TR_FLQITEM_FI and the source system DA_M_10 and regenerate the
transfer program using the function Activate. Remove possible syntax
errors on the basis of your conversion routines.
2. Restart the processing of this IDoc.
3. If the error occurs again search for SAPNet R/3 notes, and create a
problem message if necessary.
Edited by: Sebastian D'Souza on Jan 13, 2009 3:22 PMHi.......
Goto RSA1>> then to source system tab (on left side) >> double click on the desired source system...........Then on the right side you have the Datasource tree..........there search the datasource and activate.......Also u can Replicate the datasource again.......and activate the Transfer rules using the program : RS_TRANSTRU_ACTIVATE_ALL
After this operation when come back to source system (R/3).........I think the error log line will be disappeared from SM58......... Then repeat the load.........
Also u can try to Activate the infosource once...........in RSA1.........before repeating the load....
Hope this helps......
Regards,
Debjani.... -
ABAP dump error while updating product master in APO
Hi All,
Greetings from Vijay!
I need to your help to resolve below issue ;
I am getting error '
No simulation parameters could be set for the
active version'
While i am updating and trying to assign active version to my product master in APO which are created in APO for regression testing
and also sometimes system throwing dump error'
Error in the ABAP Application Program
The current ABAP program "/SAPAPO/SAPLDM_LC_SQL" had to be terminated because
it has
come across a statement that unfortunately cannot be executed.;
I appreciate your help
Thanks
Vijay JobHi Vijay,
Can you check note 1465462 ?
The same problem is mentioned in the note with correction .
Regards,
Mukesh pandey -
Dump error while filling the Setup table
Hi All,
I am trying to fill the setup table.While filling the stup table for 2lis_03_BF datasource, i got the Dump error after some time. I have checked the data in Setup table and found 9000 records.
Shall i proceed further by pulling the data from R/3 to BW.I have checked the data in RSA3 and got some data.
Shall i schedule the data from BW side.
Pls help on this issue.
Thanks,
Siva.Thanks Reddy and JS.
I have checked the TCODE SM37 and found no jobs are available. I have checked the TCODE : NPRT and found some logs.In this, it is not showing any errors.
I have checked in SM21 and found some errors.
Time_______________Text
17:08:10____________Transaction Canceled M2 630 ( )
17:23:47____________Run-time error "TIME_OUT" occurred
17:23:47____________> Short dump "090302 172347 sand1_W2 2_00 " generated
17:30:08____________Status: 80% of IL00.DAT is in use
17:30:17____________Status: 90% of IL00.DAT is in use
17:30:18____________Overflow of Paging File (032768 Blocks)
17:30:18____________Run-time error "MEMORY_NO_MORE_PAGING" occurred
17:30:19____________> Short dump "090302 173018 sand1_W2 2_00 " generated
Shall i execute filling the setup table again. Do i need to give termination time More ( 2 Hrs difference)
Any issue on refilling the setup table again.
Pls suggest.
Thanks,
Siva. -
Short dump error while filling setup tables for 2LIS_06_INV
Hi All,
I am trying to fill the setup table.While filling the stup table for 2lis_06_inv datasource, i got the Dump error after some time.
Error
Runtime Errors DBIF_RSQL_SQL_ERROR
Exception CX_SY_OPEN_SQL_DB
Short text
SQL error in the database when accessing a table.
plz can anyone help me out...Dear friends,
I tried it by giving the selection on fiscal year,but again same problem.If i give 1 0r 2 document numbers in selection then extractor works fine.
error:in detail.
Runtime Errors DBIF_RSQL_SQL_ERROR
Exception CX_SY_OPEN_SQL_DB
Short text
SQL error in the database when accessing a table.
Information on where terminated
Termination occurred in the ABAP program "SAPLMRMBW" - in "BW_RETRIEVE_DB_CO".
The main program was "RMCENEUR ".
In the source code you have the termination point in line 827
of the (Include) program "LMRMBWF01".
The program "SAPLMRMBW" was started as a background job.
Job Name....... "RMCENEUR"
Job Number..... 10524100
The termination is caused because exception "CX_SY_OPEN_SQL_DB" occurred in
procedure "BW_RETRIEVE_DB_CO" "(FORM)", but it was neither handled locally nor
declared
in the RAISING clause of its signature.
The procedure is in program "SAPLMRMBW "; its source code begins in line
806 of the (Include program "LMRMBWF01 ".
806 FORM bw_retrieve_db_co USING t_mcrbkey_bv TYPE mcrbkey_t
807 t_mcrbkey_nbv TYPE mcrbkey_t
808 t_ekbe_acc TYPE t_ekbe
809 CHANGING t_mcrbco TYPE mcrbco_t.
810
811 TYPES: BEGIN OF s_target.
812 TYPES: table_left LIKE rbco.
813 TYPES: table_right TYPE rbex.
814 TYPES: END OF s_target.
815 TYPES: t_target TYPE TABLE OF s_target.
816
817
818 DATA: t_rbco_nbv TYPE t_target,
819 t_rbco_bv TYPE t_target,
820 s_rbco TYPE s_target,
821 s_ekbe LIKE ekbe,
822 s_mcrbco TYPE mcrbco,
823 l_index LIKE sy-tabix.
824
825 * Data source: invoice item non-background
826 IF NOT t_mcrbkey_nbv[] IS INITIAL.
*>>>>> SELECT * FROM rbco AS r LEFT OUTER JOIN rbex AS i*
828 ON ( rmandt = imandt AND
829 rbelnr = ibelnr AND
830 rbuzei = ibuzei AND
831 rcobl_nr = icobl_nr )
832 INTO TABLE t_rbco_nbv
833 FOR ALL ENTRIES IN t_mcrbkey_nbv
834 WHERE r~gjahr = t_mcrbkey_nbv-gjahr AND
835 r~belnr = t_mcrbkey_nbv-belnr.
836 ENDIF.
837 * Data source: invoice item background
838 IF NOT t_mcrbkey_bv[] IS INITIAL.
839 SELECT * FROM rbco AS r LEFT OUTER JOIN rbex AS i
840 ON ( rmandt = imandt AND
841 rbelnr = ibelnr AND
842 rbuzei = ibuzei AND
843 rcobl_nr = icobl_nr )
844 INTO TABLE t_rbco_bv
845 FOR ALL ENTRIES IN t_mcrbkey_bv
846 WHERE r~gjahr = t_mcrbkey_bv-gjahr AND
Thnks in advance
Maybe you are looking for
-
Warning about bizarre eMac Tiger installation problem due to memory
I'm a fairly proficient user. I've upgraded the OS on my 800MHz eMac (original version with NVIDIA GeForce2 MX graphics) many times. This time, while upgrading to Tiger, I blew almost an entire weekend trouble-shooting the machine. I'm posting this s
-
When working in a Table can you have it add numbers in a column?
I know it can be done on a spreedsheet, but can it be done in a Table and if yes how?
-
Not sure where else to ask this, but i have some simple javascript as shown below that pops up applets. The problem is that I cannot figure out how to popup simultaneous ones. When one is clicked it replaces the other. Is there some Windows resource
-
Hello, i have some Problems with WebServices. When I call my function how makes the request (get_frob), it goes back to the main program and make a print! After that my request starts! I want that the request finished first and then make a print! I n
-
Breadcumbs don't work online: '404 - File or directory not found'
Breadcrumbs all work fine when testing my AirHelp application offline on my Windows 7 pc, (or if I access it as online browser based help). However, when I try to test the online Airhelp most of the breadcrumbs return a '404 - File or directory not f