Variable power supply not working in virtual elvis

When i make a virtual elvis 3d schematic i cannot get any output from the variable power source, i have played with it alot and still no output. please help.

Thank you for your time to help me out,
I got it to work using the shift+P and shift+n hotkeys. A suggestion I have is to remove the shift restraint for the GUI interface P and N buttons that appear on the screen after you highlight variable power supply, as it is non-intuitive for a user to know you must hold shift then press GUI buttons as well. I suggest coding those visual buttons to alias SHIFT+P and SHIFT+N operations when you click on them for ease of user interface.

Similar Messages

G5 Power Supply not working?

Hi, while using my G5 that other day, my screen froze. I powered off, then back up again. The screen came up but froze immediately.... Now when I turn it on the power button lights for a second then nothing. Dead. Any ideas? Could it be the power supply? Is this a costly thing to fix? My G5 is 4 years old. Worth looking into a new Pro Mac?
Thanks.
Beth

I realize this is an old thread, but just in case...
{quote:title=Beth Radisek1 wrote:}should I just bite the bullet and buy a new G5? Or sink that into my 4 year old G5? {quote}
Maybe neither? How about a used G4 for $200?
Buy 3 of them, and if one fails, just save any parts you can can, junk the rest, power up the next G4, and keep right on working.
You'll spend less on three G4's than one G5, and you'll get better reliability.
This is the road I'm taking, no more new Macs for me.

HELP! 2NX Not working, No lights, Power Supply IS worki

I know that my power supply is working (tested it elsewhere). I have the 2NX connected to power source and PC via USB. Still no lights. Tried installing software; no 2NX detected.
Is there some sort of reset I can do to the device? I'm desperate for it right now. Please help!!!
Thanks,
Lisa
XP SP2
Dell Inspiron 9300
Pentium M
.86 GHz
2 GB Ram

I know that my power supply is working (tested it elsewhere). I have the 2NX connected to power source and PC via USB. Still no lights. Tried installing software; no 2NX detected.
Is there some sort of reset I can do to the device? I'm desperate for it right now. Please help!!!
Thanks,
Lisa
XP SP2
Dell Inspiron 9300
Pentium M
.86 GHz
2 GB Ram

Variable power supply Mydaq

Hello im thinking of buying a Mydaq but im not sure if I can use for what I need it.
In class IM not allowed to use the Ni-Elvis 2 board unless a TA is present and if i run out of time theres no way for me to make up the lab.
so i have a breadboard at home from radioshack(electronics learnig kit) and the volatges go up in increments of 1.5 to 9v.
but in my lab i need to test the following voltages -5v,-10v,0v,5v,10v
from my research it seems i need a variable power supply so i can control the voltages going in into the board.i know with the elvis 2 board we can switch the voltages right from the computer.
so my question is does MYDAQ havea VPS where i can control the voltages from -10 to 10V in increments of 5? and im able to specify the increments of voltage?
also is it possible to get MyDAQ just the interface without the software?
thank you

Thanks for that link Mark W, thats' a great idea for low current situations!
Looking at page 37 of the myDAQ user manual here, it say that the analog output provides up to 2mA of current.
The ELVIS prototyping board can source up to 500mA of current.
Anthony F.
Product Marketing Engineer
National Instruments

Lms 4.2 didn't notify me when a Power supply stops working

Hi Guys
i have router 7200 , one of its power supply stops working , but lms 4.2 doesn't notify me?pls help to solve this issue
thanks
ibrahim

Ibrahim,
Is the 7200 being managed by LMS? Please confirm:
1. The device is setup to be managed by fault (reference)
2. The device credentials are correct (using the tool in Device Center)
3. That you have logging and snmp server destination = LMS server on your router.
#3 is not necessary but optional. If #1 and #2 are correct, Fault management should pick up the failure.

My ipad mini is totally drain and after plug it to regain the power its not working anymore.can somebody knows how to make my ipad work again

my ipad mini is totally drain and after plug it to regain the power its not working anymore.can somebody knows how to make my ipad work again

Reset iPad
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: Data will not be affected.

Touch Panel Shared variable binding does not work.

Hi,
Is there any reason why shared variable binding is not working under Touch Panel Target?
Is there any plan for implementing or there is some trick I should know?
Andras

RebeccaFo wrote:
Hello Andras,
which version of LabVIEW are you using? As yu can see in:
http://digital.ni.com/public.nsf/websearch/04AAA6903A9456F08625715A0026BC57?OpenDocument
it should work. So what for problems do you have?
Thanks,
Just FYI, the KnowledgeBase article linked above has been revised and moved to a new location. See the new KnowledgeBase 58JFBGD2: Are Shared Variables Available For LabVIEW Mobile Module (Formerly PDA Modul...

Bind variable peeking does not work

Oracle 9.2.0.8
create table my_table (c number);
create index i on my_table(c);
declare
par varchar2(10);
begin
par:='qqq';
for rec in (select * from my_table t where c = par or par is null )loop null; end loop;
--USES FULL TABLE SCAN, works SLOW!!!
--but the same query with constat insted of bind variable :
for rec in (select * from my_table t where c = par or 'qqq' is null )loop null; end loop;
--USES INDEX i ON column c , works FAST!!!
--WHY bind variable peeking does not work ???
end;
Thank you for reply

sqlplus:
drop table my_table;
create table my_table as select object_name as c from all_objects where rownum<=1000;
insert into my_table select * from my_table;
insert into my_table select * from my_table;
insert into my_table select * from my_table;
insert into my_table select * from my_table;
insert into my_table select * from my_table;
insert into my_table select * from my_table;
commit;
select count(1) from my_table;
COUNT(1)
64000
create index my_table_idx on my_table(c);
exec dbms_stats.gather_table_stats('bogdanov','my_table',cascade=>true)
variable par varchar2(10)
exec :par := 'www'
--FIRST CASE
explain plan for select * from my_table where c=:par or 'www'='qqq';
@?\rdbms\admin\utlxpls
PLAN_TABLE_OUTPUT
| Id | Operation | Name | Rows | Bytes | Cost |
| 0 | SELECT STATEMENT | | 64 | 1792 | 3 |
|* 1 | INDEX RANGE SCAN | MY_TABLE_IDX | 64 | 1792 | 3 |
Predicate Information (identified by operation id):
1 access("MY_TABLE"."C"=:Z)
--SECOND CASE
explain plan for select * from my_table where c=:par or :par='qqq';
PLAN_TABLE_OUTPUT
| Id | Operation | Name | Rows | Bytes | Cost |
| 0 | SELECT STATEMENT | | 703 | 19684 | 95 |
|* 1 | TABLE ACCESS FULL | MY_TABLE | 703 | 19684 | 95 |
Predicate Information (identified by operation id):
1 filter("MY_TABLE"."C"=:Z OR :Z='qqq')
--THIRD CASE very strange.... COMPARE IT WITH FIRST CASE: 123456789 vs. 'qqq'
explain plan for select * from my_table where c=:par or 'www'=123456789;
@?\rdbms\admin\utlxpls
PLAN_TABLE_OUTPUT
| Id | Operation | Name | Rows | Bytes | Cost |
| 0 | SELECT STATEMENT | | 703 | 19684 | 95 |
|* 1 | TABLE ACCESS FULL | MY_TABLE | 703 | 19684 | 95 |
Predicate Information (identified by operation id):
1 filter("MY_TABLE"."C"=:Z OR TO_NUMBER(:Z)=123456789)
Edited by: user450084 on Dec 9, 2008 5:17 AM
Edited by: user450084 on Dec 9, 2008 5:27 AM

Power button not working

iPopd touch 4th generation sleep/power button not working.
Any ideas? how long is warranty?

The standard warranty is one-year. Yu can purchase, before the one-year is up and additional year. Yu can check your coverage here:
Apple - Support - Check Your Service and Support Coverage
Have you looked at the previous discussions listed on the right side of this page under the heading "More Like This"?

Power button not working with 7.1 update

Power button not working with 7.1 update

I take it your phone was still under warranty then?!
Unfortunately I was not so lucky, and my experience was rather poor service-wise. They're called Apple Geniuses but I beg to differ...
I'm not sure where in the world you are located, but my "experience" involved visiting the Leeds store and confusing everyone with this issue. I can tell you, just by the looks on their faces, they had never been faced with this problem before!
I suggested my phone was rolled back to the version it was previously to establish whether this was the underlying issue. I was asked whether my phone had been backed up and as it had the "genius" proceeded to restore the phone "as it came out of the factory" to quote him.
When this was completed the phone was still doing the same thing and I was advised "the software update must have highlighted a hardware issue." I was told it would have to be physically repaired and was told to have this done by a third party as Apple would charge approximately £160. Incidentally, I work in IT and repair PC's, laptops and mobile devices for a living and made a point of raising that a sleep/wake button ribbon cable for an iPhone 4S can be bought on eBay for as little as £3.00...if indeed it does need replacing, which I suspect it does not.
Anyway, so now I was left with a phone for the rest of the day which was blank and still the problem remained. On the train, on the way home, you can then imagine my disbelief when I actually took the time to look at my phone's configuration and realised that iOS version 7.1 was still installed, so obviously the issue would still remain. So the visit to the "genius bar" was a complete waste of time as I'm still in the very same position, and I still blame the 7.1 update for this...let's home 7.2 is released very shortly and this solves the issue...
I have downloaded the package to roll the version back to 7.0 but I'm a little reluctant to carry this out yet as I would expect Apple to so the issue they have caused. This is NOT hardware related but software.
I seriously think Android is calling me...

HT4061 i left my ipad 3 as i will go to work when i came back from work and able to used my ipad power is not working and the ipad is warm i didnt left the ipad charging.... so i tried to again and outting it on its not working now. pls do the needful

I bought new ipad3 last week yesterday I left it on bed as I will go to work. When I came back and able to used it power is not working and feel the ipad get warm and feel let it cool down and try it again its not working at all. Kindly pls do the needful. thanks a lot

I bought new ipad3 last week yesterday I left it on bed as I will go to work. When I came back and able to used it power is not working and feel the ipad get warm and feel let it cool down and try it again its not working at all. Kindly pls do the needful. thanks a lot

Dv6 power led not working

Hi everybody!
Today, I changed the fan in my Pavilion dv6-6001eh (the original stop working). After I assembly, the power led not working anymore. I check the cable, but that's ok. Otherwise the power button working. The second power led in the right side next to USB, also not working.
Why? Maybe pressed hotkey?
Thank you.

Any advice?

HT1688 Power button not working

Power button not working on iPhone 5

This is a defect on iPhone 5 power button that wears out in about 13-14 months of usage just after you go out of warranty. Apple is aware of this issue but chooses not to accept this as a defect. I asked the Genius bar guy and they told me this is a common case recently and costs $269 to replace your phone. There is no repair option. I am very mad and believe Apple needs to take action or will lose their customers. All iPhone 5 owners that I know started having this problem in the month of 13 -14.
I believe if the numbers go high, Apple may start a recall program. Please encourage anyone with this problem to post here. $700 phone should not wear out this soon. Apparently the part is defective on almost all iPhone 5 devices.
Other threads about this:
https://discussions.apple.com/message/23797113#23797113
https://discussions.apple.com/message/23258974#23258974

Bootcamp 5.1.5621 - power saving not working

I've this mac: iMac 27 - mid 2010 - 11.3 : S/N CK0390HUDNR - Boot Rom IM112.0057.B01 - EFI 1.8 SMC 1.59F2
With latest bootcamp, power saving not working !
I enable the display power off after 10 minuts
Display power off BUT there's no way to power on !
Apple... any help ?? (hoping some apple tech looking discussions..)
Regards
Mauro

look on the page
it list which macs the zip support
if yours in not on the list use
is it on the list? Boot Camp Support Software 5.1.5621
or is it on this list Boot Camp Support Software 5.1.5640

HP Z400 Workstation Power Supply not Supported

Good Day All,
I would like to seek help on the issue that i am currently facing.
Currently, I am using an HP Z400 Workstation and decided to switch to a bigger casing. I Bought a Full tower and casing and just realized that i am unable to move the power supply (425 Watts) as well due to the cables are too short to reach the CPU main Powers.
So I bought a separate Power Supply (Cooler Master M2 Silent Pro 850 Watts).The cables are perfectly enough to reach the CPU main power source. After putting everything the pc won’t turn on……
I thought my newly power supply was defective and got a replacement at the same day. I tried the new Power supply and simply does not want to turn on… this is getting frustrating as I am unable to figure out what is really causing the issue.
I also tried to just plugging the cables at the Main power and removed all the additional devices just to test but still no luck….
I started checking forums… there is only one post regarding about unable to change any other third party Power Supply for this HP Z400 Workstation. I guess it apply to all HP Branded as well as Dell.
Guys I need your help as I don’t want to make a mistake again on considering to build another machine just because this one was not working… Maybe there is one there that manages to bypass or have a resolution on how I can successfully upgrade my Power supply using the same HP Motherboard.
Here is my Current Specs..
Processor
Intel® Xeon® Quad-Core Processor W3565 (3.20 GHz, 8 MB cache, 1066 MHz memory)
Chipset Intel® X58 Express
Here is the link for the full details of the specs
http://www8.hp.com/sg/en/products/workstations/product-detail.html?oid=3718668
Here is the power supply I want to replace http://h20464.www2.hp.com/results.htm?SID=3718668&MEID=368CA2BE-30F2-40AE-8929-DBF4AF2ADC21
Will wait for your kind reply,
Thanks

The reason it won't turn on is because pins 21 and 23 are not in the standard ATX PSU configuration. Your motherboard works with an HP configured ground on pin 21 and +12 VDC instead of the ATX (ATX12V v2.01)standard unused pin and +5VDC respectively.
Z400 PSU connector
Standard ATX PSU connector
I have not seen a non HP PSU available that would work without modification.
Not all HP's are built with propietary PSU connections most newer, non-business models use the standard ATX PSU configuration.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Variable power supply not working in virtual elvis

Similar Messages

Maybe you are looking for