Verify SCXI chassis: Configuration specifies a SCXI -1600 module but nothing was detected

Hello NI Engineer,
I am using SCXI 1001 chassis with SCXI 1600 control module, SCXI 1520 signal conditioning module and SCXI 1314 connector block to acquire data from strain gage. Once I right clicked SCXI 1001 under device and Interfaces in MAX>> test>>I found a pop up window as “Verify SCXI chassis: Configuration specifies a SCXI -1600 module but nothing was detected”.
This is what I did. I connected wires from strain gage to SCXI 1314 connector block which is then connected to SCXI 1520, placed in chassis. I connected SCXI 1600 controller module to computer using a USB 2.0 cable. As soon as I switched on chassis, I found a pop up at task bar as “SCXI 1600 is detected”. I opened MAX and right clicked NI SCXI -1001 under devices and interfaces>> Properties>>selected the accessory under module tab and got “Configuration complete” message at top of pop up window, But once I right clicked NI SCXI 1001 >> test >> I found an error as mentioned above. Also once I right clicked NI SCXI 1520, under NI SCXI 1001>> Configure TEDS>> I was not able to click scan for HW TEDS option (i.e. It’s not shown up). How to overcome these two errors? Please help me. I also attached screen shots with this. I am using windows XP.
Thanks
Dhaya.
Attachments:
Error pic 1.JPG ‏115 KB
Error pic.JPG ‏97 KB

Hi Dhaya,
You seems in the correct direction to configure the SCXI hardware. There is nothing to test on the SCXI-1001 chassis instead you can test on the individual channels inside the SCXI. SCXI 1600 will auto detect the modules inside the SCXI Chassis and display it in MAX. The next step that you may need to do is to configure the Accessories (Connector Block) that is attached to the SCXI-1520 mentioned.
Once you configure the connector block, you should be able to test SCXI-1520 channel.
In regards to TEDS, Are you using SCXI-1314T connector block (http://sine.ni.com/nips/cds/view/p/lang/en/nid/13735) which is for TEDS sensors?
I hope that this helps
- Meadow -
LabVIEW 7.0 - 2011, Vision, RT, FPGA
TestStand 3.0 - 4.5

Similar Messages

TS4006 Am trying to switch on "find my iphone" icon but cannot verify my icloud account. Tells me to see email but nothing comes thru with any instructions.

Am trying to switch on "find my iphone" icon but cannot verify my icloud account. Tells me to see email but nothing comes thru with any instructions.
Any help much appreciated as phone assistence unavailable today.

Hello Asokwah,
Sign out from your pple Id on your Device and Go to https://appleid.apple.com/cgi-bin/WebObjects/MyAppleId.woa/ and then Sign In with your Apple Id here and Under your Primary Email Address click on Resend Next to Verification Email Sent. Now Go to your Email Account and Verify your Apple Id again by clicking in the Link inside the Mail that you might have received from Apple. Now Sign In on your Device and try to make a Purchase and if it is for the first time then you will be asked to Review your Account and if you have entered your Credit/Debit card in your Account then you will have to just Enter your 3 Digits CVV Number and then click on Done. And then you can try downloading any Application from AppStore or Music from iTunes Store and check if its working.

HT4436 How about i have an apple id and it is verified but the app store says it is not still verified what can i do, i even searched on google but nothing worked

I have an Apple ID and it is verified and the App Store says it is not verified, what could I do? My cousin's said that I can download games on App Store, and I also have an Installous but it is Broken, It says API Error and API Unavailable how could I fix Installous to?

In order to properly upgrade the OS of your Mac. 10.1 Puma is really old. Your Mac has to meet the tech specs for Lion: And it would probably need to be a clean install. If you recently purchased Lion. Call Apple Care CPU and ask them to be sure. You get 90 days Free of phone support. 1-800-275-2273
Apple - OS X Lion - Technical specifications
General requirements
Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7, or Xeon processor
2GB of memory
OS X v10.6.6 or later (v10.6.8 recommended)
7GB of available space
Some features require an Apple ID; terms apply.

Can't configure a SCXI chassis (PXI-1010) with a PXI-8176 and a PXI-6052E.

I have a PXI-1010 chassis with a PXI-8176 running Windows 2000. In the rightmost PXI slot, I have a PXI-6052E. The remaining PXI slots are either empty or have misc. modules in them. I have a SCXI-1520 in the leftmost SCXI slot.
I am trying to get MAX to recognize my SCXI chassis with the SCXI-1520. When I try to add the SCXI chassis in MAX by right-clicking "Devices and Interfaces" or "NI-DAQmx", I leave the communication mode to communicate on the PXI backplane, choose SCXI slot zero, and find that the communication device field is greyed out where I want to choose the PXI-6052E. For some reason,the wizard used to add an SCXI chassis does not see my PXI-6052E pluged in to the leftmost sl
ot. Strangely, MAX does see the PXI-6052E in the "Devices and Interfaces" tree. I verified that the 6052E is working correctly. I also verified that the pxisys.ini file is in the WINNT directory. What is the problem?

I am first trying to install the SCXI chassis using the SCXI 1520 user manual. I put a PXI-6052E in the right-most PXI slot and the SCXI 1520 in a SCXI slot. On page 1-12 of the SCXI-1520 user manual, it instructs me to power up the chassis, right-click on MAX "devices and interfaces", choose the correct chassis, and click finish. The problem is, after I click finish, a window appears that forces me to choose a DAQ device. The SCXI chassis doesn't configure correctly because the wizard doesn't see the PXI-6052E.

Has anyone ever successfully done a cont double buffer acq from multiple SCXI channels AND a spare AI of the MIO that controls the SCXI chassis at the same time?

I am trying do a sanity check before I order some hardware.
What I want to do is acquire from multiple channels in a SCXI chasis and as part of the same acquisition, also read from one of the "un-used" AI channels of the MIO card.
My concern is this:
All of the channels of the SCXI chassis get multiplexed down into a single channel of the MIO card that controls the SCXI chassis. This means that channel 0 has to do multiple A/D conversions to get a reading from all of the configured SCXI channels.
Meanwhile, the other AI channel of the MIO only has to do one to get it's reading. It seems that the on-boar
d clock of the MIO would have to run at two rates to be able to read all of my SCXI channels AND the other AI channel.
What I want to do:
I want to just configure a vitual channel for all of my SCXI channels AND one more for one "odd-ball" signal that is incompatable with all of the SCXI modules.
Then I just want to list all of my virtual channels when I configure and start my continuous double buffered acquisition.
I have successfully done all SCXI channels before, but I have never tried to use one of the un-used AI on the MIO at the same time. I have used the spare DIO lines previously, but that will not work in this app.
So...
If you have done this and it worked, I would greatly appreciate hearing about any special techniques that were used, etc.
Thank you for reading this question,
Ben
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction

Jeremy answered here
http://exchange.ni.com/servlet/ProcessRequest?RHIVEID=101&RPAGEID=135&HOID=50650000000800000007C40000&UCATEGORY_0=_30_%24_12_&UCATEGORY_S=0
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction

Has anyone ever successfully done a cont double buffer acq from multiple SCXI channels AND a spare AI of the MIO that controls the SCXI chassis at the same time?

I am trying do a sanity check before I order some hardware.
What I want to do is acquire from multiple channels in a SCXI chasis and as part of the same acquisition, also read from one of the "un-used" AI channels of the MIO card.
My concern is this:
All of the channels of the SCXI chassis get multiplexed down into a single channel of the MIO card that controls the SCXI chassis. This means that channel 0 has to do multiple A/D conversions to get a reading from all of the configured SCXI channels.
Meanwhile, the other AI channel of the MIO only has to do one to get it's reading. It seems that the on-boar
d clock of the MIO would have to run at two rates to be able to read all of my SCXI channels AND the other AI channel.
What I want to do:
I want to just configure a vitual channel for all of my SCXI channels AND one more for one "odd-ball" signal that is incompatable with all of the SCXI modules.
Then I just want to list all of my virtual channels when I configure and start my continuous double buffered acquisition.
I have successfully done all SCXI channels before, but I have never tried to use one of the un-used AI on the MIO at the same time. I have used the spare DIO lines previously, but that will not work in this app.
So...
If you have done this and it worked, I would greatly appreciate hearing about any special techniques that were used, etc.
Thank you for reading this question,
Ben
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction

Jeremy answered here
http://exchange.ni.com/servlet/ProcessRequest?RHIVEID=101&RPAGEID=135&HOID=50650000000800000007C40000&UCATEGORY_0=_30_%24_12_&UCATEGORY_S=0
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction

Scxi chassis won't recognize 1163r plugin

I am using a PCI -6221 to connect to my SCXI-1000 chassis. I would like to install a SCXI 1163R plugin but the autodetect does not find it. I believe the jumpers are correct but with my limited knowledge can not be sure, they all are factory default. Card and chassis work fine with other plugins I have. Any suggestions.

Hi Cujo
Thank you for using our discussion forums.
The SCXI 1163R’s default jumper settings configures the module to be controlled with a Digital IO device. The PCI-6221 is an M Series MIO board, so you need to change three of the jumpers.
W2 should be set to M
W3 should be set to M
W4 should be set to A (Default)
W5 should be set to MIO
W6 should be set to S (Default)
Changing these jumper configurations will allow your 6221 to automatically detect your relay module.
Chris_K
National Instruments
Applications Engineer

PXI-1052 not detecting SCXI chassis

Full disclosure: I've submitted a support request on this too, but knowing that it may take some time to go through I thought I'd ping the discussion boards for any ideas people here might have as well.
I have a PXI-1052 PXI/SCXI combo chassis with a PXI-6289 card serving as the SCXI controller. Up to this point, the chassis has been controlled by a PXI-8105 embedded controller running WinXP. We are changing this. The PXI-8105 controller is being removed and instead we will use an MXI card (PXI-8360) to allow us to control the chassis via an external computer running Win7 32-bit.
With the chassis on and connected, using the Win7 computer I can see the PXI slots and the cards in them are correctly identified by model number. However, I cannot see the SCXI portion of the chassis, and when I try to manually add an SCXI chassis I am told that there is no DAQ device installed to serve as the SCXI controller. In addition, the PXI-GPIB card which is also installed is acting a little strangely. It allows me to scan for instruments, and it sees all of my GPIB instruments OK, but I don’t see a GPIB bus defined separately under Devices and Interfaces the way I did on the old controller—the instruments just show up listed under the PXI card.
I have read the Knowledgebase article on auto-detecting SCXI instruments, but it doesn’t seem to offer anything helpful. Everything works fine if I put the old controller back in and use it again, so this isn’t an issue of a bad card/chassis or the wrong card or a blown fuse or SCXI power not being on/set correctly or the DAQ being in the wrong slot. (The ONLY hardware difference is the controller being replaced by MXI; everything else is exactly the same.) All NI software on the Win7 machine is installed and up-to-date, and I even reinstalled everything just to make sure I hadn’t gotten a bad install. It seems to me like it must be either a driver or a configuration issue, but I’ve combed through the Windows Device Manager and the settings for all cards involved and can’t find any differences.
Screen shots attached. Any ideas?
Solved!
Go to Solution.
Attachments:
Win7.png ‏109 KB
winXP.PNG ‏73 KB

Hello Sara_J,
I'm going to post to the forums with my suggestions from my email so that if we find the answer it will be available to the community as well.
As long as the 6289 is showing up incorrectly you're not going to be able to use the SCXI side of the chassis. The problem looks like your 6289 is not being associated as a DAQmx device. The alias it has in MAX is showing it as a generic VISA device. You'll have to manually associate the 6289 in device driver. Normally it would show up under Data Acquisition Devices with the NI logo in Device Manager. Since its not showing up correctly it may be located elsewhere, most likely under a PCI Standard PCI-to-PCI bridge (this is how the MXI card looks in Device Manger).
Once you find it, right click and select Update Driver Software...>>Browse my computer for driver software>>Let me pick from a list of device drivers on my computer. You should then be able to pick the appropriate driver from the list.
If this does not fix the issue then I believe there may be a corruption in your installation of DAQmx. You can download the newest version (9.9) here: http://www.ni.com/download/ni-daqmx-9.9/4707/en/ .
Jonathan L.
Applications Engineer
National Instruments

HELP, SCXI Chassis Distance

Is it possible to extend the distance between the PC with the DAQ board and
the SCXI chassis from the official 10 meters to 300 feet?

The main issue with going over the 10 meter limit is signal degredataion due to the high capacitance of the SH68-68 cable. If one were to construct their own cable by only running the necessary communication and analog lines, it is possible that the 10-meter rule could be extended due to a decrease in overall capacitance. Just keep in mind that NI does not generally support this type of effort.

Configuration check request

we need test 10 pieces of thermocouples ,3 LVDT signals and 3 strain guage at one time.we both want the configuration of the signal conditioning and DAQ device meet our requirements and the low cost,so we select the following configuration:
SCXI-1000
SCXI-1520
SCXI-1330(instead of SCXI-1314)
SCXI-1540
SCXI-1330(instead of SCXI-1315)
SCXI-1102
SCXI-1330(instead of SCXI-1300)
PCI-6023E(12 bit is enough)
SSH6868
SCXI-1360,SCXI-1361
we hope these selections can make a whole DAQ system,could you check the configuration and please tell us if there is existing any mistake,and welcom better configuration. thanks

Instead of the SSH6868, you will need a shielded cable assembly to connect your 60xxE (E-series card) to the SCXI chassis. You will require the SCXI-1349 cable assembly. It has two parts 1)SH6868 cable and 2) an adapter to connect to the SCXI backplane.
As for the choice of the DAQ card,you may find the low cost approach severly limits the system bandwidth and overall accuracy. The low cost E-series boards only have 512 samples of onboard memory, as opposed to 8192 for the regular E-series. This makes controlling buffered analog input more difficult. In addition, you need to understand that the rated sampling rate for the board is based upon a single data channel. As you have 16 channels, your "best" sampling rate would be approximately 12.5 KHz per channel. The actual rate will be less. You have made no mention of the type of data you want to acquire (steady-state, dynamic, time domain, frequency domain), so, I can not give any better insight into the "best" sampling rate you could achieve.
Now, considering that you are mixing thermocouple (TC) readings with other inputs on the same DAQ call, you may find the 12-bit selection aggravates your data quality. When you acquire data using a multiplexer, the quoted accuracy for the device assumes that all of the voltage levels on the various channels are very near the same value. This allows a relatively uniform settling time for the input signal. It is quite possible that the TC inputs will be on the order of 2-10 mV while the other signals could range as high as 0.5 volts. Such a difference in input levels can lead to settling errors that are not obvious to the user, but can cause gross errors in the measured data levels. If you set the input range (only 4 for the low cost e-series) to +0.5/-0.5 volts, your resolution for the TCs will be about +/- 0.24 mV or about 6-10 degrees of error. (ouch!!). So you will be required to set different input ranges for the different input channels (0.05/-0.05 for the TC and +5/-5 or +.5/-.5 for the remaining channels. These multiple range calls can further limit your bandwidth by slowing down the "round-robin" interval between the data range changes. I know that your goal is low cost; however, you may find that the data quality is unacceptable. You will want to consider, at the very least, upgrading to the 6034E board. It is a 16-bit device (still only four input ranges); however, if you configure the board for only 1 input range, +0.5/-0.5 volts, your bandwith will improve and the TC resolution will improve by a factor of 16 times to approximately 0.015 mV (under 1 degree).

MAX detects PXI-MXI-4, but fails to detect non-NI chassis

MAX detects PXI-MXI-4, but fails to detect non-NI chassis. My system is as follow:
NI PCI-6552 (NI DAQmx device)
NI PXI-MXI-4/ PXI-8331 (PXI system)
Elma chassis, with CompactPCI backplane (chassis and cPCI)
When I run MAX, it successfully detects PCI and PXI with the model number listed. However, the chassis is unidentified. Although my chassis is made by Elma, not NI, it has been confirmed that my Elma chassis, as well as the CompactPCI backplane that comes with the chassis, is compatible with the PXI.
When I clicked on "other chassis", the chassis.ini (driver) file is asked. But I've confirmed with Elma that no driver is required for the chassis.
What might be the problem? Thank you very much.
Manson

I'm having a similar problem, and from reading the above, it's not clear what one is to do if the chassis and link vendors say "there are no driver files, and none are needed" and NI says, "you must have the appropriate files, which are provided by the vendor." Specifically, I have a Jasper Electronics PXI chassis and a Hartmann StarFabric link (PCI bridge). My NI devices in this chassis (6071E, 6533) have always worked fine, and MAX displays them correctly under Traditional Devices and under DAQmx Devices. The PXI chassis shows up as "unidentified" in MAX, but this has never caused any problems before (and I've seen the same benign error with other non-NI PXI chassis). However, now that I'm using DAQmx, I'm trying to do the following:
DAQmxConnectTerms("/Dev3/PXI_Trig0", "/Dev3/PFI5", DAQmx_Val_DoNotInvertPolarity);
where Dev3 is a PXI-6533. When I start my task, I get the error message "Driver cannot complete the route, because the only way to make the route requires a trigger bus line, and no trigger bus has been configured in MAX for this device." The documentation seems to imply that identifying the chassis will automatically create or recognize the appropriate PXI trigger lines. Since the vendors don't supply any ini files, I tried faking it out as as PXI-8150 system with a PXI-1000 chassis, using the NI ini files; this resulted in entries for both NI cards appearing under "Chassis 1 (PXI-1000)", e.g.
PXI5::11::INSTR (PXI-6533)
PXI5::12::INSTR (PXI-6017E)
although their properties (in the pane to the right of the tree view) show their chassis and slots as "unknown." When I run my code, I still get the error message about needing to configure a trigger bux in MAX. Just for grins, I tried the same thing but with RTSI0 instead of PXI_Trig0, and got the same error. I created an RTSI cable under DAQmx Devices in MAX, and that made no difference. Help!
Thanks,
Larry

It keeps having me verify my billing won't let me download apps update apps nothing I don't want to purchase anything but it insist on me putting in credit card info please help

It keeps having me verify my billing won't let me download apps update apps nothing I don't want to purchase anything but it insist on me putting in credit card info please help

If you want to use your current ID you will either have to provide a credit card or redeem an iTunes gift card. Otherwise you can create a new ID without a credit card to purchase free apps by following this exactly as written: http://support.apple.com/kb/ht2534.

The iCloud was never verified therefore never backing up anything on my iphone 4s because it was the wrong email and now I'm trying to make a new one but it says if I delete the account it will remove it's data from my phone. Will I lose everything?

The iCloud was never verified therefore never backing up anything on my iphone 4s because it was the wrong email and now I'm trying to make a new one but it says if I delete the account it will remove it's data from my phone. So if I put delete account will I lose everything on my Iphone?

This was EXACTLY what I needed about the purchases I made from my device. However, is there a way to re-download other ones you've made from a computer? Because I realized some of them were not just purchased from my device.
This is a picture of what it looks like now:
http://tinypic.com/r/107quxu/7
As you can see, the stuff circled in red doesn't give me an option to download from Cloud Beta because it already says "downloaded".
any way to get around that?

Anyconnect fails to connect with a message that it tried to set a specific MTU but it was already enabled with a different MTU - (SOLVED)

Cisco Anyconnect 3.1.05160 fails to setup the VPN tunnel, it prompts with this message:
"The VPN client driver encountered an error. Please restart your computer or device, then try again."
Authentication and everything seems to go through but it won't work.
The computer is a brand new HP with Windows 7. I have treid first with some later 2.x Anyconnect with same result.
The follow entries are printed in the event log:
Level Date and Time Source Event ID Task Category
Error 2014-05-10 16:19:28 acvpnagent 2009 None Termination reason code 13:
Unable to start VA, setup shared queue, or VA gave up on shared queue.
Error 2014-05-10 16:19:28 acvpnagent 2 Engineering Debug Details Function: CVpnMgr::main
File: .\VpnMgr.cpp
Line: 1847
Invoked Function: IHostMgr::enableHostMgr
Return Code: -23592949 (0xFE98000B)
Description: HOSTMGR_ERROR_ALREADY_ENABLED_WITH_DIFFERENT_MTU:An attempt was made to enable the tunnel's network interface with a specific MTU but it was already enabled with a different MTU.

This was caused by the good old HP mess-up-your-computer services.
Disable the service "HP Device Locking / Auditing" and the VPN will be able to connect.

The user or users have been added successfully, but there was an error in sending the e-mail message. The server may not be set up correctly to send e-mail. To verify that e-mail is configured correctly, contact your server administrator

I got this problem when I tried to configure out-going email and add an account to farm administrator group.
I configure out-going email according to this website http://technet.microsoft.com/en-us/library/cc288949.aspx
Here are the screen shots.
The SMTP server and email accounts work out OK when I use Outlook 2010 to test.
Anyone can help me about it? Thanks.
Here is the log.
09/20/2012 09:21:00.36 w3wp.exe (0x1F7C)
0x1138
SharePoint Foundation E-Mail
8gsf
High
#160008: The e-mail address 'admin3.sharepoint@domain' contains illegal
characters. df98555c-612f-4a58-9443-ab6e9a4fcc53
09/20/2012 09:21:00.36 w3wp.exe (0x1F7C)
0x1138
SharePoint Foundation General
8kh7 High
Cannot complete this action. Please try again.
df98555c-612f-4a58-9443-ab6e9a4fcc53
09/20/2012 09:21:00.36 w3wp.exe (0x1F7C)
0x1138
SharePoint Foundation E-Mail
7946 Critical
Cannot complete this action. Please try again.
df98555c-612f-4a58-9443-ab6e9a4fcc53
09/20/2012 09:21:00.36 w3wp.exe (0x1F7C)
0x1138
SharePoint Foundation Runtime
tkau Unexpected
Microsoft.SharePoint.SPException: The user or users have been added successfully, but there was an error in sending the e-mail message. The server may not be set up correctly to send e-mail. To verify that e-mail is configured correctly, contact your
server administrator. at Microsoft.SharePoint.ApplicationPages.AclInv.SendEmailInvitation(EntityEditor picker, String subject, String message) at Microsoft.SharePoint.ApplicationPages.AclInv.BtnOK_Click(Object sender, EventArgs e)
at System.Web.UI.WebControls.Button.OnClick(EventArgs e) at System.Web.UI.WebControls.Button.RaisePostBackEvent(String eventArgument) at System.Web.UI.Page.RaisePostBackEvent(IPostBackEventHandler sourceControl, String
eventArgument) at System.Web.UI.Page.ProcessRequestMain(Boolean includeStage...
df98555c-612f-4a58-9443-ab6e9a4fcc53
The e-mail address I have tested it for several times and there is no problem.
Anyone has any clue about this error?

Hi.
This I have seen before...
It can be that the SMTP relay server is configured to only allow certain IP ranges or addresses.
It can be that the firewall on the SP server does not allow for SMTP traffic (normally 25, for example for Exchange).
It can be that there is an Antivirus on the SP server(Client AV) that prohobits the Timer service to send email from this server. I have seen MacAfee do this. Needed an policy change.
If, its the builtin SMTP service you are using, check this link:
http://blog.sharepointrx.com/2010/11/18/setting-up-the-iis-smtp-server-for-sending-email-from-sharepoint-2010-on-server-2008-r2/
Check that and try again.
Regards
Thomas Balkeståhl - Technical Specialist - SharePoint -
http://blog.blksthl.com
Download the SharePoint Branding Project here
Download the SharePoint 2010 Site Settings Explained here

Verify SCXI chassis: Configurat​ion specifies a SCXI -1600 module but nothing was detected

Similar Messages

Maybe you are looking for

Verify SCXI chassis: Configuration specifies a SCXI -1600 module but nothing was detected