Verizon DSL and Airport Extreme

I'm going to add aniBook (oe whatever Apple will call it by then) this spring, as I want to enjoy the wi fi fun like evryone else. My ISP is Verizon DSL, and I was wondering if anyone else here in the discussion board is currently using an Ibook with Verzion DSL and Airport Extreme. I think Verizon has a modem that supports both wired and wireless networking--which is what I'll need since I won't be retiring my iMac G5 anytime soon. So any adive or info would be appreciated.

I currently have the ActionTech Modem (supplied by Verizon) as my wireless router, but would like to replace that with my Airport Extreme. Can this be done?
You will need both. Since both supply NAT, DHCP services and WiFi Access Point, you will have to turn off all three of those in one of them. This is usually called putting the device in "bridge" mode. My recommendation is to turn off those features on the Actiontech modem/router/access point, turning it into a plain DSL modem, and let the AEBSn do all the 3 features (NAT, DHCP, AP).

Similar Messages

  • Verizon DSL and Airport Extreme Setup Problem

    I have Verizon DSL (not FIOS). I am using a Westell modem, model number B90-210015-04.
    I try to go through the setup but the Airport Extreme Utility says it cannot find a valid IP address (the light keeps flashing).
    I have it setup in bridge mode since I think my modem is also a router. However, there are a lot of other inputs in the setup and I don't know if I need to put in anything for those (e.g. DNS Servers, Domain Name, etc.). I called Verizon and they said there shouldn't be any special inputs. They implied it should just work out of the box.
    The modem is working with my existing Netgear router (model number WGR614 v4).
    Any help?

    Had the same problem. Had the same setup as yours.
    If you use WPA/WPA2 and if your password is too short (less than or equal to 8 characters), the AirPort Extreme Utility will misleadingly tell you it cannot find a valid IP address. As it turns out, WPA/WPA2 requires a longer password (see http://en.wikipedia.org/wiki/Wpa2). I don't understand why a weak password would result in a confusing error message like this, but after I used a stronger and longer password, the dreadful amber light finally turned green!
    PS: I didn't enter any DNS/DHCP info nor my DSL account/password info throughout the entire setup process. I figured that if I didn't need these pieces of information with the old router before then I shouldn't need them with this new hardware.

  • Verizon DSL, Westell & Airport Extreme Base Station

    Last year I posted a desire to hook up my AEBS and AEX to a Westell wireless network. After much discussion and many suggestions I created a network that worked but was occasionally flaky.
    Since that time our family has replaced two old G3 laptops with two new Mac laptops that have poor wifi range, esp. when connecting with the Westell. I'm considering a new setup with the Westell 327W DSL wifi modem/router as a DSL modem only and letting my AEBS and AEX handle all the wifi duties in a WDS network.
    I have found instructions on the net for setting up the Westell as "modem only" but with other third party wifi routers (not Apple's). Every instruction seems specific to a particular router and the more I search the more I find "oopsies" where someone left out part of the instructions. The AEBS will also need to be connected to an 8 port switch to handle 2 printers and an older Windows PC.
    Has anyone actually set up a Westell 327 as modem only with an Airport Base station? If yes, please post details.
    Thanks,
    TW

    Connect the AEBS (or AirPort Express) to the modem via Ethernet (through the switch or not). If you want the wireless clients on the same subnet as the other devices, configure the AEBS (or AirPort Express) to not distribute IP addresses.
    Then use the information in KB 107454, AirPort Extreme and Express: Using WDS to create a network from multiple base stations to connect the other remaining AirPort device wirelessly.

  • We have dsl and apple extreme router, 2 iphones, 2 ipads a pc and a macbook. wireless speeds are terrible until the macbook is disconnected, then speeds are normal. ideas?

    we have dsl and airport extreme router, 2 iphones, 2 ipads, a pc and a macbook. wireless speeds are terrible until the macbook is disconnected, then speeds are normal. ideas?

    generalgeorge wrote:
    This is a new issue on an old setup. The mac was recently upgraded to maverick. thanks
    Say no more.. upgrading to Mavericks.. any upgrade install is prone to issues.. the Mavericks one is the worst of any recent upgrades.
    Lets just try and isolate the problem.
    In the setup of the AE, give different names to the two wireless bands.. so go into the airport utility.. click the AE, Click edit.. click the wireless tab.. and now type in a new name.
    Try AE24ghz
    Then click the wireless options and change the name for the 5ghz..
    Make it AE5ghz
    Then update the AE.
    In the computer.. select either band.. and see if your other clients are affected if they use the band that the Mac is not using.
    Alternatively turn off wireless in the macbook and use ethernet.. oh please please have a Mac with an ethernet port.. otherwise buy a Thunderbolt to Ethernet adapter.. it is well worth having. wireless is never to be trusted.

  • Power backup for dsl modem and Airport Extreme

    Does anyone here have backup power for a dsl modem and Airport Extreme that is successful? I have a name brand power backup and when the power goes off both the dsl modem and Airport Extreme remain on; however, the network connection is lost so the fact that they remain on doesn't help. I have been unable to find anything about this problem on the internet generally and consultation with a well-known squad person has not helped. Any thoughts about this will be welcome.

    Yes, I agree. But since the backup power keeps the modem powered, why doesn't the dsl connection continue? The squad person I talked with told me that the speed with which the backup power units replace power during an outage is about the same across different backup brands/units (I don't recall the speed but it was in milliseconds) and should be quick enough to retain the dsl connection. Doesn't happen.

  • Extending a network with Time Capsule and AirPort Extreme (via Belkin powerline)

    Hello -
    I've seen many topics about extending wireless networks here, but none seems to resolve the issue I'm having. I currently have a setup where a DSL cable modem is connected to a Time Capsule and I need to extend this network to another room using an AirPort Extreme.
    I live in a very old apartment in Brazil and the walls seem to block the signal from one room to another, hence the need to extend it. Since wireless signal is very weak between rooms, I bought a Belkin powerline AV500 so I could connect both Time Capsule and AirPort using the electrical power at home (just installing a regular Ethernet cable between rooms is not an option).
    I started with the basics: configure the Time Capsule + DSL as a standalone network, and it works perfectly within it's range. Then I connected the Belking powerline, plugged a MacBook via Ethernet on the other end and still got very good results (actually better speed than expected). Used it for a while with streaming and other network intensive tasks to make sure it could sustain the connection.
    Finally, pluggned the AirPort Extreme on the Belking powerline and this is where the problems started. AirPort Utility 6.3.1 only gives me the option of extending a network wirelessly - it doesn't seem to give me the option of extending it via Etherenet (roaming), which is not good in my case. Luckly I had a copy of AirPort Utility 5.6 which seems to do the job (or I thought so), but it's still not working well.
    Although I managed to configure both with the same name, it doesn't seem reliable and some devices (the iPhone 5, for example) are unable to connect and end up with a self-asigned IP address. I'm almost sure I'm doing something wrong on the setup, as I've seen a similar setup working before, so if anyone out there has any clue of what can be done, it will be much appreciated.
    Attached the screenshots of both Time Capsule and AirPort Extreme configurations.
    Thanks a lot,
    -TM
    AirPort Exteme:
    Time Capsule:

    Hello JuliaApple. Welcome to the Apple Discussions!
    You have several ways to configure both base stations for what you are trying to do.
    The simplest would be to configure the Time Capsule (TC) to "join" (AirPort Utility > Manual Setup > Wireless tab > Wireless Mode = Join a wireless network) your existing 802.11n AirPort Extreme Base Station (AEBSn). In this type of configuration the TC would perform as any other wireless client and not perform as a router. It will; however, still allow for both backups and sharing USB devices attached to it.

  • Combine Timecapsule and Airport Extreme

    Hello,
    I want to use a Time Capsule and Airport Extreme to create a wireless network in the house. Both are in different rooms, and connected by physical cable to the router.
    Can they create a single wireless network in this configuration? I want to ensure they both connect to the internet through their respective cables, and avoid that they connect to each other through the wireless connection to avoid too much signal loss (several thick walls between them)
    Thanks for feedback,
    Tom

    Thanks,
    Where do I see connection type Ethernet? Using airport utility 6
    And how to connect the ethernet cables?
    Have a dsl model from my internet provider. Do I connect both time capsule and airport extreme to a port on the dsl router, or do i connect one of them (eg time capsule) to the dsl router, and the other one (e.g airport extreme) to the time capsule?
    Cheers,
    Tom

  • How to connect my iPad, Brother printer, and AirPort Extreme?

    How to connect my iPad, Brother printer, and AirPort Extreme?

    I don't believe any of the Brother printers are AirPrint-enabled. Is your Brother printer network-ready? That is, does is support either/both a wired or wireless connection or just uses USB to connect?

  • Can a time machine usb drive backup the data from an external usb drive connected to and airport extreme*

    can a time machine usb drive conected to my mac book backup the data from an external usb drive connected to and airport extreme ?

    Hi Adam, if you think yoiur HD may be failing you could do a TM restore onto the new disk. I would rather see you do a clone either SuperDuper or CarbonCopy Cloner.Of your internal drive. That way you have a bootable backup in case it does fail.
    btw - what are the symptoms of your failing drive?
    -mj
    Message was edited by: macjack

  • Macbook pro and airport extreme don't work

    A friend (and all those tv commercials) say everything just works with Macs. Well, not exactly. New Macbook Pro and Airport Extreme can't connect me to the internet. I still have PC connected via ethernet cable to my cable modem and router which is in the basement where the cable enters the house. I've tried the different options in Airport Extreme setup and nothing works. It doesn't help Apple assumes I know everything about DHP PPPOE NAT or whatever all those silly things are.
    Can anyone explain in +very simple+ terms how I get this expensive piece of aluminum connected to the internet?
    Thanks.

    Hello sofarapplesux. Welcome to the Apple Discussions!
    I assume that you will continue to use the modem and router in the basement to get your Internet access ... correct? What is the make/model of this router?
    If that's the case, I will also assume that you have the 802.11n AirPort Extreme Base Station (AEBSn) connected by Ethernet to this router ... correct?
    So your overall network configuration should look something like the following:
    Cable modem > (Ethernet cable) > \[Internet port] router \[LAN port] > (Ethernet cable) > \[WAN port] AEBSn ... close?

  • Is anyone using NETGEAR Push2TV with a MacBook Pro and AirPort Extreme and does it work well for you?

    I am interested in buying a NETGEAR Push2TV display TV streamer to use with my MacBook Pro and AirPort Extreme.
    I saw on the Netgear site that a Intel Wireless Display/WIFI driver software is required for PC's; do we have this software installed already on our MacBook Pro's? Is any one using this box and does it work well for you, any problems or setup issues?

    trying to find out same thing , store said works with new intel processor, My mini dont finding.....

  • MacBook pro and airport extreme router. How to print wirelessly to an old HP wireless photosmart all in one printer

    With MacBook pro and airport extreme router, how can I print wirelessly to an old HP wireless photosmart all in one printer?  What is needed or what process?

    You need to make sure that the HP has an updated printer driver that works with 10.6 for that printer. You can check here:
    http://www8.hp.com/us/en/support-drivers.html

  • I am trying to hook up my Airport Express to my current network and AirPort Extreme but keep getting the same error message: "This version of AirPort Utility doesn't support this base station. Go to AirPort Service and Support for more information."

    I am trying to hook up my Airport Express to my current network and AirPort Extreme but keep getting the same error message: "This version of AirPort Utility doesn’t support this base station. Go to AirPort Service and Support for more information." Any thoughts?

    This sounds as if you have an older AirPort Express that is no longer supported by the newer Mavericks operating system.
    To check and see if  that might be the case, locate the model number on the side of the AirPort Express. It will start with an "A" followed by four numbers. Hard to see in the faint print.....so you may need reading glasses or a magnifying class to see the model number clearly.
    Model numbers A1084 and A1088 of the AirPort Express are no longer supported by AirPort Utility in Mavericks.
    You will need to use a Mac running Leopard, Snow Leopard, or a PC to be able to administer the older AirPort Express.

  • Are there any compatibility issues with Sonos and Airport extreme??

    are there any compatibility issues with Sonos and Airport extreme??

    Sonos uses its own priopietory wireless protocol SonosNet to distribute audio data among all its products, thus it should not affect other network devices which use standard WiFi 802.11a/b/g/n protocol at all though they may share the same radio channel for wirless signaling.
    On my dual-band (5 GHz / 2.4 GHz) Airport Extreme staion, I select the option "802.11n Only (5GHz) - 802.11n (2.4GHz)" and turn on "Use wide channels" in Wireless configuration in order to use only 802.11n protocol and more radio channels to achieve maximum wireless bandwidth of 400 Mbps. This bandwidth is necessary for quick Time Machine backup to NAS connected to the Airport Extreme station through Ethernet cable. So my iMac and MacBook Pro always connected to the Airport Extreme through 5 GHz radio channel with 802.11n protocol whereas my iPhone 4S always connected through 2.4 GHz radio channel with the same protocol.
    In my living room Sonos ZP-90 (same as new CONNECT model) zone player is connected to Airport Extreme directly through Ethernet cable (recommended by Sonos) and Sonos S5 (same as new PLAY:5 model) zone player in bedroom is connected wirelessly through SonosNet protocol to the ZP-90 zone player in living room.
    These devices are in operation simutaneouly most of the time. Music is playing through the Sonos ZP90/S5 zone players througout the day, I am streaming viedo through Internet (fibre broadband 25 Mbps) on my MacBook Pro in bedroom or iMac in living room or reading news on my iPhone. So far so good and have no encounter any interference problem for about three years. Further more bandwidth for 802.11n protocol does not seem to be affected at all.
    In fact with a low power Fujitsu USB drive (2.5" / 500 GB, designed for notebook) plug into USB port of Airport Extreme, it can be used as NAS drive for Sonos music distribution system without any problem. Just transfer all files from Music folder in my home directory on iMac into this NAS drive and set it up as music source in "Manage > Music Library Settings" in Sonos Controller for Mac application will do. Though the same drive can be served as Time Machine's backup disk as well, an independent full-fledged NAS drive for Sonos and Time Machine backup is better long-term solution for reliability and performance. With the NAS configured as sole music source, you do not need to keep any computer powered on all the time in order to play music through the Sonos system.

  • Difference between Airport Extreme 2011 and Airport Extreme Model

    Is there a difference between Airport Extreme MD031LL/A and Airport Extreme MC340LL/A?

    To get a detailed review of the 5G AirPort Extreme please check out this SmallNetBuilder article.

Maybe you are looking for