Version 03.03.00.XO - MLS QOS not supported

Question

Hi All,
Anyone face the same problem with the following IOS Version?
MLS QOS is not supported in global command.
Switch#sh ver
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500es8-UNIVERSALK9-M), Version 03.03.00.XO RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Wed 14-Aug-13 07:26 by prod_rel_team
Cisco IOS-XE software, Copyright (c) 2005-2013 by cisco Systems, Inc.
All rights reserved.  Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0.  The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY.  You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0.  For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: 15.1(1r)SG2
Switch uptime is 6 minutes
System returned to ROM by power-on
Running default software
Jawa Revision 3, RadTrooper Revision 0x0.0x41, Conan Revision 0x1449
Last reload reason: power-on
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
License Information for 'WS-X45-SUP8-E'
    License Level: entservices   Type: Permanent
    Next reboot license Level: entservices
cisco WS-C4506-E (P5040) processor (revision 2) with 4194304K bytes of physical memory.
Processor board ID FXS1812Q346
P5040 CPU at 2.2GHz, Supervisor 8-E
Last reset from PowerUp
1 Virtual Ethernet interface
20 Ten Gigabit Ethernet interfaces
511K bytes of non-volatile configuration memory.
Configuration register is 0x2101
SWITCH(config)#mls qos
                     ^
% Invalid input detected at '^' marker.
SWITCH(config)#
SWITCH(config)#?
Configure commands:
  aaa                         Authentication, Authorization and Accounting.
  access-list                 Add an access list entry
  access-session              Access Sesion Global Configuration Commands
  agent-server                Modify DNS server properties
  alias                       Create command alias
  ancp                        Configure ANCP
  archive                     Archive the configuration
  arp                         Set a static ARP entry
  async-bootp                 Modify system bootp parameters
  audit                       Router Audit
  authentication              Auth Manager Global Configuration Commands
  auto                        Configure Automation
  banner                      Define a login banner
  beep                        Configure BEEP (Blocks Extensible Exchange
                              Protocol)
  bfd                         BFD configuration commands
  bfd-template                BFD template configuration
  boot                        Modify system boot parameters
  bridge                      Bridge Group.
  buffers                     Adjust system buffer pool parameters
  bulkstat                    Bulkstat Application
  call-home                   Enter call-home configuration mode
  cdp                         Global CDP configuration subcommands
  cef                         Cisco Express Forwarding
  cisp                        Set CISP parameters
  class-map                   Configure CPL Class Map
  clns                        Global CLNS configuration subcommands
  clock                       Configure time-of-day clock
  cluster                     Cluster configuration commands
  cns                         CNS agents
  comet-server                Configure comet-server properties
  config-register             Define the configuration register
  configuration               Configuration access
  control-plane               Configure control plane services
  crypto                      Encryption module
  cts                         Cisco Trusted Security commands
  default                     Set a command to its defaults
  default-value               Default character-bits values
  define                      interface range macro definition
  device-sensor               IOS Sensor Commands
  diagnostic                  Configure diagnostic information
  dns-server                  Modify DNS server properties
  dnsix-dmdp                  Provide DMDP service for DNSIX
  dnsix-nat                   Provide DNSIX service for audit trails
  do-exec                     To run exec commands in config mode
  dot1x                       IEEE 802.1X Global Configuration Commands
  downward-compatible-config  Generate a configuration compatible with older
                              software
  eap                         EAP Global Configuration Commands
  emm                         Specify pre-loading of MDF
  enable                      Modify enable password parameters
  end                         Exit from configure mode
  energywise                  EnergyWise Global Configuration Commands
  epm                         EPM Global Configuration Commands
  errdisable                  Error disable
  ethernet                    Ethernet configuration
  event                       Event related configuration commands
  exception                   Exception handling
  exit                        Exit from configure mode
  fallback                    Fallback configuration commands
  fhrp                        Configure First Hop Redundancy Protocols
  file                        Adjust file system parameters
  fips                        FIPS mode after next reload
  flow                        Global Flow configuration subcommands
  format                      Format the output
  global-address-family       Enter address-family base routing topology mode
  help                        Description of the interactive help system
  hostname                    Set system's network name
  hw-module                   Apply command (e.g. shutdown) to specified
                              hardware target
  hw-module                   Control of individual components in the system
  hw-switch                   Control of individual components in the switch
  id-manager                  ID Pool Manager
  identity                    Identity Configuration Commands
  infra-test                  Configure end2end properties
  interface                   Select an interface to configure
  ip                          Global IP configuration subcommands
  ipc                         Configure IPC system
  ipv6                        Global IPv6 configuration commands
  isis                        Global ISIS configuration subcommands
  issu                        no description
  key                         Key management
  kron                        Kron interval Facility
  l2                          Layer 2
  l2protocol-tunnel           Tunnel Layer2 protocols
  lacp                        LACP configuration
  li-view                     LI View
  license                     Configure License
  line                        Configure a terminal line
  link                        Enable Link State Tracking feature
  lldp                        Global LLDP configuration subcommands
  location                    Global location configuration commands
  logging                     Modify message logging facilities
  login                       Enable secure login checking
  mab                         MAC Authentication Bypass Global Configuration
                              Commands
  mac                         Global MAC configuration subcommands
  macro                       Macro configuration
  media-proxy                 Global media proxy configuration
  mediatrace                  Mediatrace Application
  memory                      Configure memory management
  metadata                    Metadata Application
  mka                         MACsec Key Agreement (MKA) configuration
  module                      Module
  monitor                     Monitoring different system events
  mvr                         Enable/Disable MVR on the switch
  netconf                     Configure NETCONF
Thank you.

Answer 1

Hi,
QOS implementation has radically changed since the advent of
sup-7 & later
You no longer set mls qos as qos is on the engine by default.
Please see the following links
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-4500-series-switches/white_paper_c11-539588.html
"Ingress QoS: Default Actions
First and foremost, QoS does not need to be enabled on the Supervisor Engine, it is on by default in compliance with the MQC construct.
When a packet arrives at an interface, there are two options to take into consideration: is there a policy attached or not? If the packet arrives with or without a marking and there is not a policy attached to the interface, packets will flow through the switch untouched. There are no questions as to where the packet came from or if it has a valid marking. If the packet arrives with or without a marking, and a policy is attached to the interface, the packet will only then be subject to the policy classification."
And the config guide
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/15-1/XE_330SG/configuration/guide/config/qos_mrg.html#wp1461453
Hope this helps
Regards
Alex