Version 3.6.36 not remembering connect to internet...

Hello -
Having just upgraded to 3.6.36, I find that these 'connect to internet' settings are not remembered between executions of Nokia Suite:
Phone service provider
Data usage reminder
The phone service provider has no default, so a dialogue pops up for it to be reselected.
has anyone else encountered this, and have you found a fix for it ?
Thanks.

mkarr, I recommend to use the PC Suite because it creates a modem once which can be re-used. Did that help?

Similar Messages

How do you resolve the problem of ipad not staying connected to internet. other laptops remain connected but ipad just disconnects after about 5 seconds.

how do you resolve the problem of ipad not staying connected to internet when other devices are connected. Ipad disconnects after about 5 seconds.

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
Additional things to try.
Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
On your iPad go to Settings > General > Reset > Reset network settings and see if that enables you to connect.
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
 Cheers, Tom

My ip3 stop..all i get is "Siri is not available connect to internet"

I have ip3. It has stop coming on. All that i get now is the audio message " Siri is not available connect to internet. Does anyone know how to fix this problem?

Johnrhinos1 please utilize a different web browser to implement you redemption code. Which web browser were you using? I would also recommend reviewing Redemption Code Help.

IPhone 4 does not stay connected to internet over 3G+

I have an iPhone 4 on the telus network running the latest version of the os 4.3.3. My phone will not stay connected to the Internet most of the time. It looses connection and won't reconnect until I turn on airplane mode and then turn it back off. It also looses connection if I have wifi on and it detects a network but choose not to connect to it. I have restored my phone and it fixed the problem for half a day before it started again. I only have a couple months warranty left, is this covered do you think?

I don't have another phone to try. I took out the sim to check for deffects but it looked fine. Cleaned the sim card with alcohol and cleaned the aim compartment. Phone didn't loose Internet connection all day yesterday, but this morning went to check emails and wouldn't update until I turned airplane mode on then off again.

WRT310N and WPA not allowing connection to internet

I just purchased a WRT310N, followed the setup instructions and selected WPA/WPA2 encryption. I put the key into my Belkin PCA card, model F5D7011 and my XBOX i get no connection to Internet from either device. I reinstalled the router and set the security option in the CONFIGURE ROUTER section to "no securty" and finished the re-install. Everything is fine. XBOX and my Dell PC connect to internet. WPA does not work. ANy help is appreciated.

Ok. i am working now. I deleted the wireless connection in the Belkin Utiliy and re-configured the router with WPA. I made the PCA card reconnect and a dialog box came up asking for the key. I did not use the random key provided by Linksys. I made up my own. Once i put the key into the belkin utility all was ok. XBOX works now as well.

Broken 4s screen and no display. Siri worked to make calls but now says "Siri not available connect to internet" still waiting on new phone and need to make calls. How can I get Siri to work again?

I broke my iPhone 4s screen and display. Siri worked to make calls but now says "Siri not available, connect to the internet". How do I make Siri work again till I get my new phone?

If not connected to the Internet, either through WiFi or 3G, you can't.

After having downloaded my e-book ADE gives the information that there is not a connection with internet. What is the problem? Liejaat.

After having downloaded my e-book, Adobe Digital Edition gives me the information that there is no connection with internet.Who can help me with this problem? Liejaa.Adobe Digital Editions

I've never seen this error in the context of trying to connect via ODP.NET or ODT.
If you have Oracle Dev Tools for Visual Studio installed, you can try to create a connection to the database using Server Explorer. If this works, that means your ODP.NET connection is just fine.
If you don't have VS or the tools, another thing you can try is connecting through ODP.NET using a simple OracleConnection.Open. Make sure you have your client set up to connect to the DB server.
Here's some info about connecting to the DB:
http://download.oracle.com/docs/html/B28089_01/featConnecting.htm#sthref101

Airport self assigned IP not able connect to Internet

I'm trying to connect my Mac Pro WiFi for the first time and have Airport turned on. Status says Airport hasna self-assigned IP adress and will not be able tonconnect to the Internet.
Anyone know how to get Airport to connect?
Thanks,
Steven

Thanks Linc, after clicking AirPort, Status is On and the correct network is showing in Network Name. when I click Advanced under AirPort tab the network shows in Preferred Networks the network I want to use.
In the TCP/IP tab Configuration IPv4 "Using DHCP" pulldown is selected and the IPv4 Address is the same as the previous screen where it says AirPort has the self assigned IP address and won't be able to connect to the Internet. Hmmm.
What I don't understand is that use this same network without any issues on my iPad and iPhone. Just Mac Pro AirPort is having a problem.
Thanks,
Steven

Wifi Connected but not allowing connection to internet....

Ok for starters I am by no means computer illiterate. I have several industry certifications and have worked in IT in one form or another for over 10 years. That being said I have tried all the obvious solutions to fix this issue. So please save your effort in telling me to flush dns servers, check connection settings on clients, run ipconfig with various switches, etc... all this has been done and failed. That is not to say I know everything, because I don’t, I’m just saying that I have tried all the obvious troubleshooting routes.
Now… on to my issue. I have a WRT54GS ver. 5 and it has worked flawlessly for several years now. My machine is hard wired to the access point and I have no troubles connecting to the internet via said PC. The wireless I use for my wife’s laptop and my iPhone. I use mac filtering and WPA Personal with TKIP, dhcp is disabled and IP's are assigned manually via TCP/IP settings in windows. Two days ago my wife complained that she was unable to connect to the internet despite the fact that she had a solid connection to the AP. After checking her machine and finding everything in order in terms of the connection settings I also discovered that my iPhone was also unable to connect to the internet via Wi-Fi, again despite a strong connection to the AP. This led me to believe that the issue lied with the AP since nothing had changed on the client machines and all the connection settings were correct. I am able to ping the AP from the client but it is not routing traffic to the internet.
That brings me to troubleshooting the AP. I logged in and verified that all settings were as they had always been in the router, not one thing had changed. So to make absolutely sure it was not some setting in the AP that had been changed somehow I reset the router to defaults and re-configured it EXACTLY as it had always been. Still no love. I also tried the following to further troubleshoot the issue with no luck:
Clearing WINS and TCP/IP stack in windows on the laptop.
Disabling WPA and connecting with no security save MAC filtering
(yes I made sure that MAC filtering was set to permit and that all MAC addresses were correct)
Upgraded to the latest firmware.
Unplugged wireless phones throughout the house and cycled through all 11 channels to rule out interference.
I guess what I am now trying to figure out is whether or not the routers Wi-Fi is bricked. Is it possible for the Wi-Fi to be bricked but still be able to connect to the Wi-Fi network with a strong signal and for wired to work just fine? I would think that if the Wi-Fi was kaput that one would not be able even connect to the AP via wireless. I am to the point now where I’m about to say screw it and just go buy a Wireless N router and be done with it. But to be honest I am a little leery of Linksys now if a two or three year old router is bricked without warning or any apparent cause. Even though I have used Linksys products for the entirety of my IT career, I am now having second thoughts about going with cisco products if indeed it is bricked and I have to go out and buy another AP. Any help the community here can offer would be much appreciated, I don’t mind getting a new AP as the N speeds would be a plus but I want to make sure that all hope is lost for the WRT54GS before I do.

Thanks for your reply.
Yes, as stated in the OP all clients wired or otherwise have IP's and DNS info manually entered in windows TCP/IP configuration. All of the IP info has been the same for years and it works fine on my machine (hard wired) with the only difference being the last octet of the IP, subnets and DNS settings are the same on all clients.
All 4 clients (My PC, Laptop, Iphone, and wireless printer) can all ping both ways without issue. As I mentioned before the wireless clients connect to the AP just fine and all settings are verified correct. My WLAN is still working flawlessly and I can connect to and view all clients and shares. The issue seems to lie with the WiFI routing to the internet: I can connect to the internet from the wired PC and all the clients on the local network have connectivity, the only issue I have is that the wireless clients (in spite of a working connection to the AP) cannot seem to get thorugh the internet. However I did change the RTS and Fragmentation to 2304 and the beacon to 50 as you advised and set the DNS servers to what you listed on the wireless machine and was still able to ping back and forth but had no connectivity to the internet.

Airport seems fine, but is not REALLY connecting to internet

Hi, I am using a Belkin 54G to connect my iBook G3 to internet. I am sharing the router with others in my house. However, things stopped working for me 2 days ago while it is fine for others.
I have restarted the machine, turning on and off the airport to see if anything would work. no luck. it shows that it detects the belkin and I do have a strong signal. however, nothing works when i try to use safari, mail, ichat, software update... etc.
has there been a recent update on airport cards that i don't know about? or is there someway i can re-setup the airport on the computer to take me back to 3 days ago (when the airport was running normally...)
thank you so much for your help!
_pt

Hello.
WiFi can get cranky without warning. You just have to adapt to the situation.
First, try resetting the router. There may be a button to do this; if not, unplug it for a minute. What many people don't realize is that the router is really a computer running server software, and all computers can get hung up and need to be rebooted. This may or may not solve your problem, but it's easy enough to do.
If your router is OK, then you need to check your MacOS X network preferences. Make sure that Airport has highest priority in your Network Port Configurations and that its box has been checked.
Please post back if these quick fixes don't work. Then you need to do some more technical stuff. Good luck.

Not always connecting to internet on command but can always recieve emails

I have a curve 8330 on the Altell/Verizon network and for some odd reason when I try to connect to the internet it won't always oblige, it will connect and work fine, then no more than 5 minutes later it won't connect for about another ten minutes, yet I'm always able to recieve emails, even when it won't connect to the internet. It's always 1X and not 1x, and I've tried all the simple fixes like a battery pull etc. Any help is greatly appreciated, thank you.
Solved!
Go to Solution.

Since you are only getting 1X, I would suggest you contact VZW for support...something is not right. 1X means that everything is going through the voice network...which can include internet access, but it will be slow and flaky. EV will give you the power of the data network...but VZW needs to help you figure out why you are not getting that.
Message Edited by sdgardne on 07-30-2009 12:17 PM
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Linksys WTR160N not keeping connection with internet

I just bought a Linksys WTR160N Broadband router and tried to connect with comcast modem Arris. Keep losing connection. Called linksys tech and he said it was my network card but when i connect direct to the modem it works fine. I bought a new linksys network N card for my laptop and it has the same problem. I am direct connected right now and has worked fine. HELP

Try to readjust the wireless settings on your router...
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
Reduce the MTU size to 1300 under setup..and Click on save settings.
For Wireless Settings, please do the following : -
- Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect...

Upload to FTP Host... not remembering ftp settings

Upload to FTP Host works well, but the settings are not remembered for subsequent uploads. How can I save the FTP Upload settings in Muse 2.2 for re-use?

Sachin,
Thank you for your note. My installed version of Muse version 2.3 does not remember any of the FTP settings in the Upload to FTP host… dialog box. This behavior is contrary to your report that Muse remembers FTP credentials. From my repeated experiences this function has no retention of previous dialog entries.
How can I make the Upload to FTP Host… remember the FTP site login, password, etc.?

Being notified when the connection to internet is establish

having a pc which is not permmanently connected to internet I want to know how can I construct a listener for being notified when a connection to internet is establish

That would require the following...
For your specific OS and environment in the OS you will need to determine the specific ways, via C API calls, callback or notification events, how to know this.
Then you write JNI code so your java application can talk to that code.
Alternatively you can just query yahoo every couple of minutes. If it responds then you are connected. If not then you are not.

HT1766 I'm trying to update my first Ipad (versions 4.2.1). Device is recognised by the computer. Advise to upgrade to 5.1x given but then followed by the message that device is not connected to internet. Connection with upgrade server not possible.

Whilst connected to the internet (reading news and sending messages) I cannot upgrade my Ipad with an error message that my device is not connected to internet. Update server can not be reached?
Any ideas.
Ipad 1, version 4.2.1

I tried resetting the ipad, switched off wifi, checked date and time.

Version 3.6.36 not remembering connect to internet...

Similar Messages

Maybe you are looking for