Vertically sync time position for two or more 2D axis systems?

In DIAdem: VIEW,
Is it possible to vertically sync the time position for two or more 2D axis system charts placed above each other?
I have displayed several channels on one 2D chart, and one channel of particular interest on a separate chart above, which was very easy to do. It would be really useful to sync the time position on both charts, such that scrolling one chart also scrolls the second chart, or zooming one chart also zooms the second chart to the same area, which seems like a fairly basic thing to want to do, but I haven't found a way to do it yet.
Any help greatly appreciated!
Solved!
Go to Solution.

Hi Brad,
Yes, I have been using that method, which works fine up to a point.
But, say you have several curves displayed on the bottom chart, with the Y-Axis set to "n Y-axes", then the start of the x-axis will be further across to the right than the top chart which has only one curve displayed.
It is possible to add an empty area to the left of the top chart, to push the start of the x-axis across into alignment (see attached), but every time you add or remove a curve on the bottom chart, or the scale changes enough to add a digit, the start of the x-axis moves and the top chart needs aligning again.
I'm really after a method to lock both ends of both x-axes to the same vertical screen position, so everything stays aligned automatically?
Attachments:
chart - full.JPG ‏152 KB
chart - detail.JPG ‏145 KB

Similar Messages

How to configure time synchronization for two NTP servers

We have IOSXR 4.2.1 on routers CRS3 and ASR9K with all recomended SMUs; we need to configure the time synchronization for two NTP servers with the configuration below, but the routers became unstable; synchronize with one NTP servers for some time, then switch to other NTP server, and keep doing this. Anyone know why this behavior?
ntp
authentication-key 1 md5 encrypted 01070F074F0A05
authenticate
trusted-key 1
server 10.192.32.32 prefer
server 10.192.32.33
source Loopback50
update-calendar
RP/0/RP0/CPU0:DFCRSDTC1#sh log | i ntp
Wed Jul 10 09:37:04.621 BRSPO
RP/0/RP0/CPU0:Jul 4 21:29:18 : ntpd[256]: %IP-IP_NTP-5-SYNC_LOSS : Synchronization lost : 10.192.32.32 : Peer unreachable or clock selection failed
RP/0/RP0/CPU0:Jul 4 21:29:18 : ntpd[256]: %IP-IP_NTP-5-HP_CONN_LOST : High priority NTP peer connection lost - Stratum 2->15.
RP/0/RP0/CPU0:Jul 4 21:29:18 : ntpd[256]: %IP-IP_NTP-5-ALL_CONN_LOST : All NTP peer connections failed.
RP/0/RP0/CPU0:Jul 4 21:29:27 : ntpd[256]: %IP-IP_NTP-5-HP_CONN_RECOVERED : High priority NTP peer connection recovered - Stratum 15->2.
RP/0/RP0/CPU0:Jul 4 21:30:21 : ntpd[256]: %IP-IP_NTP-5-SYNC_LOSS : Synchronization lost : 10.192.32.32 : Peer unreachable or clock selection failed
RP/0/RP0/CPU0:Jul 4 21:30:21 : ntpd[256]: %IP-IP_NTP-5-HP_CONN_LOST : High priority NTP peer connection lost - Stratum 2->15.
RP/0/RP0/CPU0:Jul 4 21:30:21 : ntpd[256]: %IP-IP_NTP-5-ALL_CONN_LOST : All NTP peer connections failed.
RP/0/RP0/CPU0:Jul 4 21:31:36 : ntpd[256]: %IP-IP_NTP-5-HP_CONN_RECOVERED : High priority NTP peer connection recovered - Stratum 15->2.
RP/0/RP0/CPU0:Jul 4 21:35:56 : ntpd[256]: %IP-IP_NTP-5-SYNC_LOSS : Synchronization lost : 10.192.32.33 : Peer unreachable or clock selection failed
RP/0/RP0/CPU0:Jul 4 21:35:56 : ntpd[256]: %IP-IP_NTP-5-HP_CONN_LOST : High priority NTP peer connection lost - Stratum 2->15.
RP/0/RP0/CPU0:Jul 4 21:35:56 : ntpd[256]: %IP-IP_NTP-5-ALL_CONN_LOST : All NTP peer connections failed.
RP/0/RP0/CPU0:Jul 4 21:40:11 : ntpd[256]: %IP-IP_NTP-5-HP_CONN_RECOVERED : High priority NTP peer connection recovered - Stratum 15->2.
RP/0/RP0/CPU0:Jul 4 21:50:52 : ntpd[256]: %IP-IP_NTP-5-SYNC_LOSS : Synchronization lost : 10.192.32.33 : System clock selection failed
RP/0/RP0/CPU0:Jul 4 21:50:52 : ntpd[256]: %IP-IP_NTP-5-HP_CONN_LOST : High priority NTP peer connection lost - Stratum 2->6.
RP/0/RP0/CPU0:Jul 4 21:59:26 : ntpd[256]: %IP-IP_NTP-5-HP_CONN_RECOVERED : High priority NTP peer connection recovered - Stratum 6->2.
RP/0/RP0/CPU0:Jul 4 22:25:07 : ntpd[256]: %IP-IP_NTP-5-SYNC_LOSS : Synchronization lost : 10.192.32.33 : System clock selection failed
RP/0/RP0/CPU0:Jul 4 22:25:07 : ntpd[256]: %IP-IP_NTP-5-HP_CONN_LOST : High priority NTP peer connection lost - Stratum 2->6.
RP/0/RP0/CPU0:Jul 4 22:56:16 : ntpd[256]: %IP-IP_NTP-5-SYNC_LOSS : Synchronization lost : 10.192.32.33 : Peer unreachable or clock selection failed
RP/0/RP0/CPU0:Jul 4 22:56:16 : ntpd[256]: %IP-IP_NTP-5-ALL_CONN_LOST : All NTP peer connections failed.

Hi Claudio, that ddts is pretty generic to be honest but yes it is filed to address sync issues in the XR NTP algo.
The thing is that XR ntp clock selection is a bit different then iOS and follows the specs very closely which results in this erroneous loss behavior.
For instance, you could also see this issue with a sync loss if the update time is only 500msec off what it was before and that will result in a ntp sync loss rather then adjusting to it.
Also I wanted to mention that the ntp prefer is a bit of a misnomer in XR (since it follows the specs differently then IOS) and this knob was taken over from IOS really.
You might get some joy if you set it to one server only and see if that helps?
regards
xander

WHERE clause creating a join for two or more tables

The CS3 Dreamweaver book says that the WHERE clause can
create a join for two or more tables. The join was created, but the
data is repeating. I have searched the web and this forum and have
not found the answer.
My Master page filters the recordset by Style No and when a
customer clicks on a particular style, it sends him to the Detail
page. All the records are showing from all tables on the detail
page from the Dynamic List, except they are showing multiple times
(ex. Size table has 4 sizes and Color table has 2 colors - my Size
Drop Down list is showing 8 options and my Color Drop Down List is
showing 8 options) I have a Master Page with a recordset pointing
to a Detail Page using the same recordset.
Master page works perfectly.
Master Recordset SQL:
SELECT products.itemID, products.category, products.styleno,
products.name, products.description, products.ourprice,
products.imageTH, products.image, coloroption.color,
sizeoption.size
FROM products, coloroption, sizeoption
WHERE category = 'chefcoats' AND
products.styleno=sizeoption.styleno AND
products.styleno=coloroption.styleno
GROUP BY products.styleno
ORDER BY styleno ASC
The Detail Recordset:
SELECT products.itemID, products.category, products.styleno,
products.name, products.description, products.ourprice,
products.imageTH, products.image, sizeoption.size,
coloroption.color
FROM products, sizeoption, coloroption
WHERE itemID=colname AND products.styleno=sizeoption.styleno
AND products.styleno=coloroption.styleno
I tried using the GROUP BY on the detail page, but then it
only showed one size and color from the dynamic drop down list. I
tried changing the field name "styleno" in the other tables to be
unique, however, I was using the table identifer. I tried using the
JOIN command instead of the WHERE clause and that didn't help
either.
On the detail page, the customer is supposed to click on the
Size box and see sizes XSM - 6XL ONLY ONE TIME. and then be able to
click on the Color option and see White, Black, Red ONE TIME.
Is this possible?
Thank you for giving your time to read this.!
Evie

Do you have a link we can look at to see what you are trying
to do?
Dave
"EviePhillips" <[email protected]> wrote in
message
news:[email protected]...
> The CS3 Dreamweaver book says that the WHERE clause can
create a join for
two
> or more tables. The join was created, but the data is
repeating. I have
> searched the web and this forum and have not found the
answer.
>
> My Master page filters the recordset by Style No and
when a customer
clicks on
> a particular style, it sends him to the Detail page. All
the records are
> showing from all tables on the detail page from the
Dynamic List, except
they
> are showing multiple times (ex. Size table has 4 sizes
and Color table has
2
> colors - my Size Drop Down list is showing 8 options and
my Color Drop
Down
> List is showing 8 options) I have a Master Page with a
recordset pointing
to a
> Detail Page using the same recordset.
>
> Master page works perfectly.
> Master Recordset SQL:
> SELECT products.itemID, products.category,
products.styleno,
products.name,
> products.description, products.ourprice,
products.imageTH, products.image,
> coloroption.color, sizeoption.size
> FROM products, coloroption, sizeoption
> WHERE category = 'chefcoats' AND
products.styleno=sizeoption.styleno AND
> products.styleno=coloroption.styleno
> GROUP BY products.styleno
> ORDER BY styleno ASC
>
> The Detail Recordset:
> SELECT products.itemID, products.category,
products.styleno,
products.name,
> products.description, products.ourprice,
products.imageTH, products.image,
> sizeoption.size, coloroption.color
> FROM products, sizeoption, coloroption
> WHERE itemID=colname AND
products.styleno=sizeoption.styleno AND
> products.styleno=coloroption.styleno
>
> I tried using the GROUP BY on the detail page, but then
it only showed
one
> size and color from the dynamic drop down list. I tried
changing the
field
> name "styleno" in the other tables to be unique,
however, I was using the
table
> identifer. I tried using the JOIN command instead of the
WHERE clause and
that
> didn't help either.
>
> On the detail page, the customer is supposed to click on
the Size box and
see
> sizes XSM - 6XL ONLY ONE TIME. and then be able to click
on the Color
option
> and see White, Black, Red ONE TIME.
>
> Is this possible?
>
> Thank you for giving your time to read this.!
> Evie
>
>

I have a problem, my wife has an ipad with photos , emails etc etc, she has recently got herself a new iPad Air, has now been using that for two or more months, more photos (new) more emails and other stuff. Will send next query as running out of room to

I have a problem, my wife has an ipad with photos , emails etc etc, she has recently got herself a new iPad Air, has now been using that for two or more months, more photos (new) more emails and other stuff. What she wants to do is get all she wants from ipad 1 to new ipad without finishing up with 2 of everything which happen on previous occasion. I realise that she needs to tidy up ipad 1 first and get rid of thousands of emails etc. I need help.
Thanks kiwihdrider

Hi yes that works well when the new ipad hasn't been used. Trouble new one has been used for two months or more, has lots photos email etc etc. I am worried that these will go. When we did iPhone thru same process finished up with two of most things pics and emails. The emails alone were over 2 thousand and wife reluctant to delete them all. I would and just sort pics. Any other ideas
Ta

HT4623 I am upgrading my iPad to iOS 7 but the progress bar is at 1/4 position for two hours and not moving forward. Is there any problem with it? What should I do? Thanks.

I am upgrading my iPad to iOS 7 but the progress bar is at 1/4 position for two hours and not moving forward. Is there any problem with it? What should I do? Thanks.

This is a concern amoung many corporate users. It's going to take somekind of policy change with apple.
Enterprise support:
Call enterprise support (866) 752-7753 to create a case ID number

Reading monitor vertical sync time

I'm using Labview 5.1 in Win98. I'm writing a program for a psychology experiment where a subject responds to events on screen, and we record the response time in milliseconds. Response is recorded by a NI digital I/O card.
I'd like to synchronise graphic drawing on screen with the vertical flyback of the monitor (the vertical sync pulse), or alternatively, be able to read the millisecond counter value at the last vertical interval. Is there any way of doing this, maybe with a Windows API call?

Is there some sort of hardware signal that would accompany the vertical sync pulse? If you can get a hardware signal, synchronizing things will be much easier. I've never tried anything like this, but I can imagine several problems trying to do it through software. For one, I would bet that the type of functionality you want would be controlled by the graphics and video drivers, which means that you could not get it from a Windows API. Even if you could create a windows event for it, by the time you captured the event in your control software, you will have already lost several microseconds.

END ROUTINE to calculate time differnce for two corresponding dates

Hi All,
I have to write an END ROUTINE in which I have 2 DATE FIELDS (e.g. DATE_1, DATE_2) and corresponding TIME fields (e.g. TIME_1, TIME_2).
I have to calculate difference between the TIME fields for the two dates and populate a TIME_DIFF field.
Can someone pls help me by posting sample code as i am new to BI.
Thanks in ADVANCE!!!

End Routine:
http://help.sap.com/saphelp_nw70/helpdata/EN/e3/732c42be6fde2ce10000000a1550b0/frameset.htm
End Routine and Expert Routine
Thanks..
Shambhu

Itunes for two (or more)?

Just got my Nano today, and want to know if I can share the previously installed itunes that my daughter has been using? When she plugs her ipod into the computer, it automatically downloads her changes from itunes. How does it work with two or more units? Let's face it, I don't want her music and she doesn't want mine. Thanks.

OR you could each make separate playlists for each person and only have each individual playlists selected for each ipod. http://www.apple.com/support/ipod/tutorial/ipgettingstartedt2.html
or for more on using manual mode http://www.apple.com/support/ipod/tutorial/ipgettingstartedt3.html
Another option would be in Windows every windows account gets it's own itunes library.

How do i sync the tempos for two different tracks playing at the same time?

i am new to audition so i apologize if there is an easy answer to this question, but...
i upload two different two different songs and i want to get them to play at the same time and sound halfway decent. how do i get the tempos to match?

http://www.adobeforums.com/webx/.2cccd873/0

How do you sync iTunes library for two user accounts?

Hello
I have a MacBook with two user accounts - myself and my wife.
I have to do this because we both have iPhones and we need to keep our sync-ing separate or we would just keep overwriting each others preferences.
I have an iTunes library and so does my wife.
Problem...
I recently imported some songs using my account that my wife wants on her iTunes. When I logged out of my account and went into hers the songs I imported were not there!!
Question...
How do you marry and update the libraries of both accounts so no matter which iTunes library you access (my account or hers) you have all the available songs in both?
I have tried trawling through some of the zillion posts here, but the prospect of spending hours and hours was just too much to contemplate!!!!
So if i've asked a question that has already been asked and dealt with please forgive me - or better still if you know where the needle would be in this haystack a link would be very much appreciated!
Many Thanks in Anticipation.
Mr Totsy

Hi ffiti
I have done a bit of cleaning up on my Mac (OCD!) and made a bit of an ar*e of things - can you help?
I went into my wife's account and wiped all iTunes files and stored songs.
This was done because some songs were on my iTunes library and some were not on hers - so I just wiped the lot off and started again...I know it gets even better...
I then went into my user account and wiped off everything there too...
I went on the Apple website and downloaded the latest iTunes 11.0.4 I think and reinstalled an empty library from scratch - that way I will be only filling one library full of songs - I also took the media file out of the shared folder and reset it back to its default position
I went to sync my iPhone and now it tells me I can only sync one device with one library - so how do I sync my phone without it deleting everything and replacing it with nothing?!!!!
I doesn't matter how great Apple products are they just can't account for human idiocy !!!
Regards,
Mr Totsy

One single account for two or more devices??

I'm about to buy the new iPod Touch 4. I really liked the last version of iPod Touch 3 and I became a big fan of it. So when I knew about the new iPod 4 I start to think to "upgrade" my old iPod Touch 3.
I'm wondering if there's any way to transfer all my apps that I bought in my iPod 3 to the new iPod 4 and keep my account intact. The old one I'll give it to one of my little brothers and I'm wondering if I have to reset the iPod in order to transfer my account to the new one.
Thanks for your time and help!

I'm wondering if there's any way to transfer all my apps that I bought in my iPod 3 to the new iPod 4 and keep my account intact.
Just sync the new iPod, using the Transfer Purchases command in iTunes while the older one is connected if the purchases aren't in the iTunes library.
(54880)

CProjects - Partition for two or more groups on the same system

Hi,
Our business requirement for cProjects implementation is such that we have two groups (two companies infact) under an umbrella brand. We have already impemeneted cProjects for one of them. It's time now to have this implemented for the other group.
How can we ascertain that there's a partition in the system by which one group is completely independent of the other? One group should not see the projects/data of the other group and vice versa. Authorizations to projects helps but in a system, a user can fetch (in project search) the names of all projects in the system (irrespective of whether one has authorization). How can we take care of this?
Summary:
We are looking for the ssytem where one group of cProjects users works in the system as if it were the only group working. We intend to ensure the same for the second group as well.
Please suggest.
Regards...

Hi Zhenbo,
You get points for the "very helpful answer". Thanks.
I have not been able to make a complete breakthrough though. Please see if you can help.
There are three steps under "Structural Authorization"
1. Create Authorization Profile: I see this defined in my system (comes from HR)
2. Save user in SAP Memory (IMG has enough documentation on this.
3. Assign Autorization profile to users: Here, I assigned one of the "Auth. Profiles" to the user (myself). At this, I see that the system (cProjects front end) returns an empty list.
This means that the system expects the Business Partners, pertainig to that "Auth. Profile" (which I set in step 3 above). And because it does not find any, it returns an empty list.
What I am not looking for is:
How to bring in the Business Partners (we are using the HR Master Employees) under this "Auth. Profile" such that the system picks them when we do a resource search at cProjects front end?
So... what I am looking for is: relation between this "Auth. Profile" assigned to the user and the Business Partners corrresponding to this "Auth. Profile".
Please see if you can help.
Regards,
Bittu.

Getting iCal to sync with iCloud for two Macs, and a 3G iPhone

I currently have a Macbook and MacMini both running 10.7.2, and just started using iCloud this week to sync contacts, iCal, bookmarks, etc. I thought I initially had problems with iCal as I was getting two copies of every event showing up on my MacBook, but then realized I had two sets of calanders, ("on my mac" and "iCloud"). After I unchecked the "on my mac" calanders, everything appeared normal.
The problem I face now is with my 3G iPhone that can't run iOS5, and thus, no iCloud. My iCal on my iPhone is set to sync with my "on my mac" calanders, so with those unselected, the events are not showing up on my Macbook, and thus, aren't being synced to my MacMini.
My question is, can I have my 3G iPhone sync to my iCloud calanders everytime I connect it to my Macbook to sync via USB, instead of syncing with the "on my mac" calanders as it is currently doing without have iOS5 capabilities on my iPhone? If not, is there a way to have iCloud keep syncing with my "on my mac" calander list, so that it is always up to date, and data from my iPhone will be synced over to my iCloud calander list from the "on my mac" calander list?
I'm just trying to figure out if I'll be able to transfer new iCal dates I create on my 3G iPhone over to my iCloud calander list, and ideally, vice versa.
Thanks in advance for the help.

I understand that iCloud won't run on it or with it. I'm just trying to figure out if there is a way to sync the "on my mac" calanders (which sync to my iPhone iCal everytime I connect via USB) continually with my iCloud calandars so the two are always up to date.

Dynamic file naming for two or more files in same mappin

Hello,
I am working with Dynamic file naming on receiver files...
Here two files are coming as output files...
I am using JAva UDF to handle the two file name....
But one one file is formed and another is missing as its 505 file aleady existing error is coming in Receivr Communication channel monitoring...
How to name different dynamic names for the two differenet files

Hi Sunil,
Go thru this blog:
The specified item was not found.
Use this Variable Substitution method as an alternative option:
http://help.sap.com/saphelp_nw2004s/helpdata/en/bc/bb79d6061007419a081e58cbeaaf28/frameset.htm
SAP NetWeaver XI: Variable Substitution with Adapter-Specific Message Attributes via DynamicConfigurationBean
OR
The specified item was not found.
Regards,
Vinod.

Using Time Machine for two computers, not simultaneously.

Using a WD external HD via Firewire 800 to backup my main computer with Time Machine. I use my 13" MacBook Pro while away from home for weeks, then putting it away when home. (Note: not networking between them.) I do want each computer to be identical so that when I leave with my MacBook, my programs and data are the same. I do have MobileMe at both locations. Can I update the MacBook before going back to it by disconnecting Time Machine from my iMac, connecting Time Machine to my MacBook Pro via Firewire 800 and restoring?
Thanks for your help.

Using a WD external HD via Firewire 800 to backup my main computer with Time Machine. I use my 13" MacBook Pro while away from home for weeks, then putting it away when home. (Note: not networking between them.) I do want each computer to be identical so that when I leave with my MacBook, my programs and data are the same. I do have MobileMe at both locations. Can I update the MacBook before going back to it by disconnecting Time Machine from my iMac, connecting Time Machine to my MacBook Pro via Firewire 800 and restoring?
Thanks for your help.

Vertically sync time position for two or more 2D axis systems?

Similar Messages

Maybe you are looking for