Very bad broadband speed for the last 4 days...

Hi all,
for the last 4 days, I am experiencing some big difficulties with my broadband connection.
Half the day it is fine (morning), half the day is it terribly slow, to the point I cannot connect to any website.
This affect not just my computer but all my other devices connected to the internet : second pc, Xbox 360, PSP. Thay use all wired connection, exept the PSP.
Here are 2 speed test carried one when it works fine,and one not so well:
I have done the 2 first Speedtest, the third one does not woks.
What I have tried to fix the problem :
change router
change noise filter plugs
reset
nothing works.
I have visited the BT Major Service Outages, but nothing is reported in my area.
Can you help me find out what is wrong please?
Thank you for your help

I'm now back on the website....
Love to know what is going on here...
ADSL Line Status
Connection Information
Line state:
Connected
Connection time:
0 days, 02:48:06
Downstream:
7.938 Mbps
Upstream:
448 Kbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.1 Annex A
Latency type:
Fast
Noise margin (Down/Up):
8.2 dB / 22.0 dB
Line attenuation (Down/Up):
32.1 dB / 20.0 dB
Output power (Down/Up):
19.8 dBm / 11.9 dBm
FEC Events (Down/Up):
0 / 0
CRC Events (Down/Up):
66 / 1
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
95 / 0
Error Seconds (Local/Remote):
64 / 1

Similar Messages

Very slow internet speed for the last few days

I don't know what happened but I'm experiencing low speeds when browsing the internet, to navigate this page it took me ages , this is my line status, anything wrong with it?
ADSL line status<script type="text/javascript"></script>
Connection information<script type="text/javascript"></script>
Line state
Connected
Connection time
0 days, 1:24:31
Downstream
575 Kbps
Upstream
828 Kbps
ADSL settings<script type="text/javascript"></script>
VPI/VCI
0/38
Type
PPPoA
Modulation
ITU-T G.992.5
Latency type
Interleaved
Noise margin (Down/Up)
35.5 dB / 9.6 dB
Line attenuation (Down/Up)
17.5 dB / 9.6 dB
Output power (Down/Up)
19.2 dBm / 12.4 dBm
Loss of Framing (Local)
0
Loss of Signal (Local)
0
Loss of Power (Local)
0
FEC Errors (Down/Up)
0 / 44
CRC Errors (Down/Up)
0 / 2147480000
HEC Errors (Down/Up)
nil / 721
Error Seconds (Local)
0

my speed keeps going down.
I had to swap my v2 hub to my old v1 hub because I've noticed the v2 keeps rebooting itself for no reason and it's really frustrating if I need to keep it on all the time as advised to get better profile
my questions are:
Why my old hub is more stable than the new one?
why my speed keeps dropping when my line is capable of 20mb and I achieved it after the engineer's visit last week but a couple of days after started to go down?
isn't it my upload speed to low?
this are my statistics:
Uptime:
0 days, 0:38:47
Modulation:
G.992.5 annex A
Bandwidth (Up/Down) [kbps/kbps]:
1,106 / 6,654
Data Transferred (Sent/Received) [MB/MB]:
9.08 / 55.28
Output Power (Up/Down) [dBm]:
12.5 / 20.0
Line Attenuation (Up/Down) [dB]:
9.0 / 21.5
SN Margin (Up/Down) [dB]:
5.5 / 27.0
Vendor ID (Local/Remote):
TMMB / TSTC
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
Loss of Link (Remote):
0
Error Seconds (Local/Remote):
0 / 0
FEC Errors (Up/Down):
0 / 0
CRC Errors (Up/Down):
0 / 0
HEC Errors (Up/Down):
0 / 0
Line Profile:
Fast
this morning the speedtester said my Ip profile was 5500, a couple days ago was 13000, before that 19000
this is my last speedtest http://www.speedtest.net/result/955401239.png

How do I set a reminder for the last day of every month

Have I missed something? But how do you set a reminder for the last day of every month to recurr indefinatley in iOS6? Sorry if this is really simple but I just can't seem to work it out. Any help gratefully received.

Hey Mattye88 not sure if you have seen but actully you can do this, but for some reason you have to use Siri. If you bring up Siri and say "set a reminder ever 4 weeks from next wednesday to check the gas meter" it will set one and it will work just fine, I have reminders to water a Bonsai every three days and it works fine it just shows as custom repeat on the user interface. Alas it seems you can not use Siri to set one for the end of the month though which is why I am in this threed. Still hope it helps you to know how to sort this problem atleast.

How do I set a recurring event for the last day of the month on iphone 4s calendar?

I want to set a recurring event for the last day of every month - regardless of the date/number of days in the month. I'd prefer not to have to use an app to do this.

Hi,
You can do this using the custom repeat in iCal. You'll need two events to cover the second and fourth Mondays.
Create the event on the second Monday of the month. In Repeat select Custom... > Frequency: Monthly > On the: second Monday.
Do the same for the Fourth Monday.
Best wishes
John M

How to get the date for the last day of a week?

Is there a easy way to get the date for the last day of week?
eg a week starts on monday and end on sunday
January 11, 2005 is the start date for the week
January 17, 2005 is the end date for the week
or
say
February 26, 2003 is the start date for the week
March 5, 2003 is the end date for the week
I just need a simple way of figuring that out....
I figured out how to get the start date for the week but just can't get the latter..
formatting of the date is not of a concern.. that I know how to do
thanks in advance

How about something like the following?
     Calendar someDay = new GregorianCalendar(2005,0,11);//2005 Jan, 11
     //Note above that January is 0, not 1, as counting starts from 0.
      someDay.add(Calendar.DAY_OF_MONTH,6); //add 6 days
     java.util.Date lastDayOfWeek = someDay.getTime();
     //If someDay was the start of a week, lastDayOfWeek should now be
     //the last day of that week.
     System.out.println(lastDayOfWeek.toString() );

I need help in Downloading Adobe Elements for my Mac & Adobe Acrobat for my laptop...I have been battling for the last day.

I need help in Downloading Adobe Elements for my Mac & Adobe Acrobat for my laptop...I have been battling for the last day.

~graffiti wrote:
PjonesCET wrote:
I know if you attempt to download and exe file to Mac from a Mac Partition you'll get something like. Cannot not understand file format octet-stream. This means it does not recognize MS execute files.
Not necesarily. I've done it a few times.
PjonesCET wrote:
I'm not sure you can download a PC copy of Acrobat 9 unless you operating from bootcamp or other such application and running the PC partition.
Yes. You can.
I've learned something. New. This must be recently changed. That last time I clicked on a Link I though was a dmg file and turned out it was and exe file my Macs wouldn't allow me to do so. But haven't tried recently everytime and exe file comes up I cancel. I gues I am used to the time everytime a Virus or some other nasty was downloaded it was packaged in and exe file and Macs owuldn't allow it. I suppose with the INtel guts now they can no longer refuse to download.

I am Greek. I downloaded a film from ipad but for the last days it has not been downloaded and the status is "waiting".the charge has been made to my credit card. Does any body knows?

I am Greek. I purchased a film from ipad but for the last days it has not been downloaded and the status is "waiting".the charge has been made to my credit card. Does any body knows?

something other is dowloading somewhere on ipad

My macbook has Itunes and I am trying to download some songs that I bought on my Ipad onto the macbook. It has worked in the past, but one song has been downloading for the last day. No more will download it seems stuck downloading.

My macbook has Itunes and I am trying to download some songs that I bought on my Ipad onto the macbook. It has worked in the past, but one song has been downloading for the last day. No more will download it seems stuck downloading. I don't need the song. But I want the others to download.

Hi there,
You may find the information in the articles below helpful.
Downloading past purchases from the iTunes Store, App Store, and iBooks Store
http://support.apple.com/kb/ht2519
iTunes: How to resume interrupted iTunes Store downloads
http://support.apple.com/kb/ht1725
-Griff W.

Very Slow Broadband Speed for 2 months, and very U...

Hi
I know exactly how you feel (Giza). I took out BT Total Broadband and had it installed on 02/12/2010. Day one I have 6.75 mbps, which was great as my previous provider only gave me 5 mbps max. So I was well please.
Then day two it dropped to 4.35 mbps, not much to worry about, just though as it was Friday the network would be busy. Then on day 3, I was getting 0.65 mbps, and I have battling with BT ever since.
I have had the usual c**p from BT in India about moving the router due to interference etc, but of course non of them worked. Finally they advised I needed an engineer to come out, so I booked it for next working day between8am and 1pm, he arrived at 12.45, so a good job I took the day off work.
All he did was re-wire by master socket, called a help desk and told them to reset my IP profile, and was going in 30 minutes. He just told me to keep and eye on my speed as it should get faster within 5 hours. 48 hours later still at 0.65 mbps. So once again called BT to be told they are still working on the problem and will contact me when it is fixed. Two week later, still no increase in speed.
So I called them and they apologise for not getting back to but they were very busy. Their solution was that I needed another engineer to visit. So again I book the next available slot, but this time for afternoon slot 13.00 to 18.00 hours, so I only need half a day off work (obviously BT don't realise people work).
He arrived at 13.45, and he seem very knowledgeable to the other guy, and he even advised he had worked for BT for over 28 years. He check the line coming into the house first then the same test at my socket, and advised there was not problems there and my line was above average quality and I was on a ADSL2 21C exchange (whatever that means), so he decided to go to the cabinet at the end of the my street, he was gone about 45 mins. He came back to advise it appeared I was cross-communicating with another circuit. He did another line test, but had to call the help desk to reset my line again as it was not giving his little box of tricks access to my full capacity.
Buy the time he was done it was 17.45, and had got me up to 10.9 mbps hand-shake with the exchange (I was so please I could have kissed him), and rang through to another help desk to reset my IP profile again to increase my speed, but as it finished at 18.00 he waited to see if it was done, but did say it can take anywhere from 5 minutes to 5 hours for the request to be processed.
So left the computer on, and did some chores. Now when he left my router had been connected for over an hour and a half and he advised there should be no reason for it reset. At 18.15 the router crashed, when it came back the hand-shake had gone down to 9.6 mbps, but my speed was still at 0.65 mbps. Then at 6.30 the router crashed again, then again, and again. Finally came back on at about 19.00. The hand-shake had come back at only 4.55 mbps.
Then at 19.30 I got a call from BT to say they were calling to see if I was happy with the service and had the engineer fixed the problem. Funnily enough just as they called the router crashed again. So I advised them of the above, and was told to do a hard reset on the router (use a paper click to press the reset button). Waited till I was re-connected. I was then told to test my speed at speedtest.net. Which I did, and I was getting, wait for it 2.35 mbps. The woman on the end of the phone advised, there you go it is fixed.
To which I clearly advised was not the case, and I should be getting 8.5 mbps as per the engineers advised. She all she could say was she needed to speak to the technical team and call me back. Which I was surprised she did at 20.20. Next action is to have another engineer come out and check the fault.
So now I am on my 3rd engineers visit, booked for this Friday afternoon. I did call the help desk, and asked for my service to be cancelled as I was that mad and upset about the service, but was told that as it was not BT's fault over my speed (god know's who's fault it is) I would need to pay for the remaining 15 months of my 18 month contract, but if I got the engineer to note on my account on Friday that it was their fault, I could cancel free of charge.
So been at work all day today, and though I would check my speed. Hand-shake now at 1.15 mbps, and my speed is at 0.65 mbps once again.
While writing this, I did not notice my Hub has once again crashed, and is just sat on yellow for Broadband. Of course if you are reading this I got it re-connected.

Good fun isn't it
After all that I would (including your other topic )
1 ask for a new hub or try another router if possible
2 Contact Mods at
[email protected]
include a link to this topic account number and phone number
If any post helps tick the star box on the left
Just cause Im paranoid dont mean they are not out to get me

Customer exit variable for date range for the last day

Hi,
If user enters date ranges in variable
suppose user enters 9/1/2010 to 9/15/2010 and we have to calculate currency conversion based on last day i..e 9/15/2010 . 08
2)User input is date range 08/01/2010 to 08/30/2010
I need from the customer exit 08/30/2010 (on last day) to calculate currency conversion.
Can anyone help me with ABAP code to achieve this customer exit?And please tell me how to proceed step by step
Sridhar

create a variable to enter date range (ZDATE1)
create a key date variable(ZDATE2) with processing type customer exit, should not be ready for input.
In the exit ZXRSRU01 write below code.
DATA: l_s_range TYPE rsr_s_rangesid,
      loc_var_range LIKE rrrangeexit.
WHEN 'ZDATE2'.
    IF i_step = 2.
       read table i_t_var_range INTO loc_var_range
                with key vnam = 'ZDATE1'.
        CLEAR l_s_range.
        l_s_range-low = loc_var_range-high.
        l_s_range-sign = 'I'.
        l_s_range-opt = 'EQ'.
        APPEND l_s_range TO e_t_range.
    ENDIF.

Day and Month date format - Calculating a measure only for the last day date format

Good evening all,
I'm really struggling with a MDX query and so would greatly appreciate your help ..
Here is a simplified representation of my data:
Id
Tenor
VarX
1
10-Jan-14
10
2
10-Jan-14
10
3
10-Jan-14
10
4
11-Jan-14
10
5
12-Jan-14
10
6
13-Jan-14
10
7
Feb-14
10
8
Mar-14
10
9
Apr-14
10
And here is the MDX result I’m trying to get:
Tenor
VarX
VarY
10-Jan-14
30
0
11-Jan-14
10
0
12-Jan-14
10
0
13-Jan-14
10
90
Feb-14
10
0
Mar-14
10
0
Apr-14
10
0
Where: if tenor is the last tenor in day format (i.e. dd-mmm-yy) VarY = total sum of VarX else VarY = 0
Here is a first try below which hopefully will help you understand my problem.
MEMBER [Measures].[VarY] AS
IIF (
ISEMPTY([Measures].[VarX])
OR vbamdx!Len([Tenor].CURRENTMEMBER.Name) <= 6
OR TAIL(
FILTER(
{[Tenor].[ALL].CHILDREN},
NOT (ISEMPTY([Measures].[VarX])) AND vbamdx!Len([Tenor].CURRENTMEMBER.Name) > 6
).ITEM(0).Name <> [Tenor].CURRENTMEMBER.Name,
NULL,
SUM ( [Tenor Group].[Tenor Group].[all], [Measures].[Delta] ) )
Please let me know if you have any ideas and/or advice.
Thanks in advance! Kevin

Hey Aleksandr
Tenor is a string. The tenor table is used by other reports too and contains tenors in day, month, etc format (e.g. 01-Jan-14, 02-Jan-14, 03-Jan-14, ..., Jan-14, Feb-14, ...).
This is why I was trying to differentiate the 2 "groups" of tenor using length.
Something like:
MEMBER [MEASURES].[MOUT] AS
iif(
isempty([Measures].[VarX]),
null,
iif(
(Len([Tenor].CURRENTMEMBER.NEXTMEMBER.Name) =
Len([Tenor].CURRENTMEMBER.Name)
null,
SUM ( [Tenor].[all], [Measures].[VarX])))

(South wales) Very bad Broadband Speed, please he...

Hi there guys. First off i tryed reading the stickies and didnt find anything that helped me.
Ill explain whats going on. Ive only been with Bt for about 2 months, the told me that i can get 3.Mbps on my Line, so ofc i have 2.5 but only 0.5 of a meg wasnt a big deal to me. 3 days ago there was a problem in our living area and was confrimed by the Bt BB service status that i phoned and they said that the problem would be resovled in 2 hours, after about 4 hours we phoned again and said there were no further problems.
BUT since then (3 days) broadband has be so very very slow its honestly unbelieveable, last time i did a speed test at speedtest.net, i was 0.16 Download (page took 2 mins to load literally) and its been between 0.16 - 0.43 the fastest ive seen it go. Ive also not changed anything in my home.
Ive got the 2.0 hub pluged directly into the master socket, i dont have sky tv or other phones around the house to interfere. My router is siting on a small table on its own, no where near cheap cordless phones(only got the hub phone) no speakers or anything. this is also my 2nd hub
heres a copy paste job from the hub manager.
Line state
Connected
Connection time
0 days, 0:13:31
Downstream
283 Kbps
Upstream
546 Kbps
VPI/VCI
0/38
Type
PPPoA
Modulation
ITU-T G.992.5
Latency type
Interleaved
Noise margin (Down/Up)
20.8 dB / 8.8 dB
Line attenuation (Down/Up)
56.5 dB / 31.4 dB
Output power (Down/Up)
17.8 dBm / 12.2 dBm

Hi,
First thing your router has not been on long 13 mins on your post, 3 days it will take to get up to speed, however you should see a increase in 24 hrs if no other issues but I have feeling you do have a problem, run a speed test do it three times every hour or so. Your first test shows it is slow and at that point it will not get any faster really. Have you tried the noise line test.
Try this link this will give you some idea on the speed you will get, if all was perfect, you should also take perhaps 1mbps off, to have a reasonable estimate.http://www.kitz.co.uk/adsl/max_speed_calc.php.
Just enter your line annuation it is 56.5.
Also give the mods a post here with a link to this thread, they will need your name and number, [email protected]
Mortgage Advisor 2000-2008
Green Energy Advisor 2008-2010
Charity Health Care Provider Advisor 2010-
I'm alright Jack....

Was anybody else's broadband down for the last 10-...

Mine was down since yesterday evening. It's just come back on though. I turned the power button on the hub off then back on, tried the reset button on both the hub and the modem but in each case the light settled back on orange. Was this problem specific to my line or did others experience similar? I am on Infinity 2 if that matters.

I suggest you try a factory reset of the hub
http://bt.custhelp.com/app/answers/detail/a_id/11386/~/how-do-i-reset-my-bt-home-hub-to-its-factory-...
If you found this post helpful, please click on the star on the left
If not, I'll try again

Recomended Broadband Speeds for new Apple TV

I was about to purchase an Apple Tv earlier today, but wanted to check the recommended broadband speeds for the service.
We suffer from speeds of 2.5mbps; probably not a problem with Apple TV - being able to download to the HDD for viewing later. However, streaming only is a little concerning - especially as we'd be looking at HD stuff.
Have Apple said what speeds are required? Is contents buffered to some sort of memory until it is ready to be viewed.

The avatar HD film was 5.8gb in size from the itunes store. My internet speed is usually around 9.8mbps but can drop down to 7mbps in busy times. I rent HD films a lot and it usually takes about 20 seconds to 1 minute from pressing rent to being able to play the HD movies. Only once have I had an issue with the film freezing up half way through, it turned out the internet went down on my ISP side of things.
As apposed to having 2.5mbps I am not to sure on times but it would just be a case of waiting longer at the beginning before pressing play, for the film to build up in the buffer so you don't catch up to where the film has got to in downloading. That is if my understanding of the apple tv downloads and plays at same time is right! If I am wrong I would be very interested in knowing exactly how it works.
But to answer the question at the beginning I have not seen an official minimum download speed for the apple tv but looks like from other peoples experiences you can't go wrong with something bigger than 6/7mbps.

Define event to repeat on the last day of each month?

(I've searched the forum and can't find this question addressed)
I want to create a repeating event for the last day of each month. Is this possible?

Unfortunately Apple does not have an option available that allows you to add an event repeating on the last day of the month. An "OK" way around this would be to repeat on the 1st of every month and send a reminder a day earlier. I know this is less then perfect but the only option currently available. If you happen to find a 3rd party program that allows such integration please don't hesitate to mention it here as I have been looking for this sort of option for quite some time now!

Very bad broadband speed for the last 4 days...

Similar Messages

Maybe you are looking for