Very disapointed, SP13 doesn't runs on SUN Cluster!!

Hello, this is the 3rd time that we tried to install a support package in our productive SAP Enterprise Portal (SP10, SP12, SP13), and fails again.
We restore the SP09 backup, and doesn't work also, and now we haven't portal!
How is possible this? We are very disapointed, SAP support can't solve the problem.
I have a published blog with more comments about this:
http://rafaelco.blogspot.com

I have succefully installed SP 9, SP 12 and SP 13 in SUN Solaris 9, with many problems as well but It worked at the end.
If you tell me what kind of problems do you are you facing, maybe I can help.
Regards

Similar Messages

  • Running a Sun Cluster on one system using containers

    Hello,
    We would like to set up a test Sun Cluster Environment on one system using containers.
    Has any one done this ? Is there documentation in the sun community on how to do this ?
    Thank you
    Bradley Duncan
    Application Support
    City University of New York

    You can not install/configure a cluster just between non-global zones on the same physical node. The cluster software always needs to be installed in the global zone.
    What you can do is install Solaris Cluster just on one physical node (a single-node cluster) and then you can configure native non-global zones and configure resource groups to failover between those non-global zones on the same node.
    The resource group has a nodelist property, where you can configure node:zonea,node:zoneb - which will allow that RG to failover between zonea and zoneb on the same node.
    A good start if your purpose is just to have a learning/development/experiment environment.
    Regards
    Thorsten

  • What are typical failover times for application X on Sun Cluster

    Our company does not yet have any hands-on experience with clustering anything on Solaris, although we do with Veritas and Miscrosoft. My experience with MS is that it is as close to seemless (instantaneous) as possible. The Veritas clustering takes a little bit longer to activate the standby's. A new application we are bringing in house soon runs on Sun cluster (it is some BEA Tuxedo/WebLogic/Oracle monster). They claim the time it takes to flip from the active node to the standby node is ~30minutes. This to us seems a bit insane since they are calling this "HA". Is this type of failover time typical in Sun land? Thanks for any numbers or reference.

    This is a hard question to answer because it depends on the cluster agent/application.
    On one hand you may have a simple Sun Cluster application that fails over in seconds because it has to do a limited amount of work (umount here, mount there, plumb network interface, etc) to actually failover.
    On the other hand these operations may, depending on the application, take longer than another application due to the very nature of that application.
    An Apache web server failover may take 10-15 seconds but an Oracle failover may take longer. There are many variables that control what happens from the time that a node failure is detected to the time that an application appears on another cluster node.
    If the failover time is 30 minutes I would ask your vendor why that is exactly.
    Not in a confrontational way but a 'I don't get how this is high availability' since the assumption is that up to 30 minutes could elapse from the time that your application goes down to it coming back on another node.
    A better solution might be a different application vendor (I know, I know) or a scalable application that can run on more than one cluster node at a time.
    The logic with the scalable approach is that if a failover takes 30 minutes or so to complete it (failover) becomes an expensive operation so I would rather that my application can use multiple nodes at once rather than eat a 30 minute failover if one node dies in a two node cluster:
    serverA > 30 minute failover > serverB
    seems to be less desirable than
    serverA, serverB, serverC, etc concurrently providing access to the application so that failover only happens when we get down to a handful of nodes
    Either one is probably more desirable than having an application outage(?)

  • SUN Cluster 2.2 behaviour when removing SCSI from A1000

    We're running a SUN Cluster 2.2 , 2 node cluster on a SUN E5500 running Solaris 5.8 and Veritas VM.
    A1000 Boxes cross connected over SCSI to each node and D1000 dual attached per node.
    What would one as cluster behaviour expect if one Node crashes, powering the crashed node off and removing the SCSI cable from the A1000 to the surviving node. Would the surviving node continue to run properly ?
    Thanks

    There is potential that the surviving node could panic when termination is lost when the cable is disconnected.

  • SUN Cluster 2.2 behaviour when remoing SCSI

    We're running a SUN Cluster 2.2 , 2 node cluster on a SUN E5500 running Solaris 5.8 and Veritas VM.
    A1000 Boxes cross connected over SCSI to each node and D1000 dual attached per node.
    What would one as cluster behaviour expect if one Node crashes, powering the crashed node off and removing the SCSI cable from the A1000 to the surviving node. Would the surviving node continue to run properly ?
    Thanks

    There is potential that the surviving node could panic when termination is lost when the cable is disconnected.

  • I don't want to stay with iOS 7 any more, i can't tolerate it to being very slow and to hand while playing games, it doesn't run properly, i have no games in my phone right now becouse of that bug, could i downgrade my ios of iphone 4s? Please help thanx

    I don't want to stay with iOS 7 any more, i can't tolerate it to being very slow and to hand while playing games, it doesn't run properly, i have no games in my phone right now becouse of that bug, could i downgrade my ios of iphone 4s? Please help thanx

    That is HANG sorry miss type

  • Applet embedded in JSP doesn't run on browser with older than JRE-1.6

    I have embeded an Applet in my JSP Page which used JDK1.6's getHardwareAddress() method to get user's physical address.
    I have embeeded this into a JAR file and used it in my JSP where this applet run on onload() event of the form --> runs the applet --> and gets physical address of user machine and prints it in one of the text boxes on the form.
    Now, the issue is that the applet doesn't run on browser that doesn't support JRE 1.6
    My concern is that how can I run this (if at all possible) in browsers that support lower versions of JRE or is it possible to check that if the browser doesn't support JRE 1.6 then load the basic version of form without running the applet. Can i actually check the version of browser JRE somehow and stop to execute the applet. Because what happens as of now is that if the applet doesn't execute, the complete form fails to load.
    The last option is that I give a message on my web page that redirects user to Sun Java site and asks them to update their browsers.

    Personally, I have no knowledge about Applet but have you checked this link?
    [http://blogs.sun.com/thejavatutorials/entry/deployment_toolkit_101|http://blogs.sun.com/thejavatutorials/entry/deployment_toolkit_101]

  • Nsswitch doesn't run PADL's nss_ldap.so

    Hi, all!
    I've really broken my brain.
    I've successfully compiled PADL's nss_ldap-253 with openldap-2.3.21 and openssl-0.9.7i. All linked static.
    /etc/nsswitch.conf reads "passwd: files ldap". nss_ldap.so copied to /usr/lib/nss_ldap.so.1.
    When I run `getent passwd` it displays content of /etc/passwd only and exits with code 0. truss shows that it opens /usr/lib/nss_ldap.so.1. But it doesn't run any functions, even nssldap_passwd_constr().
    I've downloaded ready-to-use nss_ldap.so.1 from www.symas.com and it works fine. It frustrates and encourages me. I cannot understand what is wrong with my job?
    I have Sun Fire V240, Solaris 9 9/05, GCC 3.4.2.
    openssl-0.9.7i:
    # ./config no-hw threads
    # make ; make install
    openldap-2.3.21:
    # ./configure disable-ipv6 disable-slapd disable-slurpd disable-shared --without-cyrus-sasl \
    --with-tls CPPFLAGS=-I/usr/local/ssl/include LDFLAGS=-L/usr/local/ssl/lib
    # make depend ; make ; make install
    nss_ldap-253:
    # CPPFLAGS=-I/usr/local/ssl/include LDFLAGS=-L/usr/local/ssl/lib LIBS="-lssl -lcrypto" \
    ./configure with-ldap-dir=/usr/local with-ldap-lib=openldap --enable-rfc2307bis \
    with-ldap-conf-file=/etc/ldap.conf with-ldap-secret-file=/etc/ldap.secret
    # LDADD=-L/usr/local/ssl/lib make
    # cp nss_ldap.so /usr/lib/nss_ldap.so.1
    # ln -s /etc/ldap.conf /usr/local/etc/openldap/ldap.conf

    GCC 3.4.2 was the matter. GCC 3.3.2 works fine.

  • Migrate Sun Cluster (+RACdisks to new hardware running Sun Cluster ( + RAC)

    Hello,
    We have old hardware (v490s) running Sun Cluster 3.2 + Oracle RAC 10.2.0.4.0 connected to SAN. We need to move to T4. Oracle advised against including new hardware into existing cluster, so we are planning on building a new cluster with T4's, same software (Solaris 10, Sun Cluster 3.2, RAC 10.2.0.4.0).
    When ready, we plan to shut down existing cluster, zone new cluster to existing disks and bring up everything on new hardware (simply stated).
    Will it work?
    Any gotchas - like need to clear disk ids or Sun Cluster panicking? RAC panicking? Any reference docs out there?
    Thanks
    user12961096

    Do we absolutely need that in our new setup or could we forgo that additional layer? Would Sun Cluster give us anything that the OS + RAC doesn't give us?Yes, Oracle Solaris Cluster does make things a lot easier. It looks after your device space and gives you consistent DID devices for CRS/RAC. It gives you the choice to use sQFS, raw metasets, or ASM. It has clprivnet which is a lot easier and performs better than an IPMP solution. The node failure detection time is <= 10 seconds which is quicker than CRS on it's own and it uses SCSI fencing instead of a STONITH approach. Finally, you have all the off the shelf agents that Solaris Cluster offers.
    However, if you are only doing RAC and you just want ASM and you don't need the last few seconds of failure detection that OSC gives you and you think STONITH is good enough for your fencing purposes, then CRS on its own is perfect. There are many, many deployments both with and without OSC, it's not a simple yes/no answer.
    Having worked for the Solaris Cluster group, I'm still slightly bias to including it rather than going without. Others have the alternate view! :-)
    Hope that helps,
    Tim
    ---

  • Bin doesn't run

    I evryone,
    I have download jsdk+netbeans+etcetc from sun page and I follow the instructions to install it.
    I have solaris 10 and I enter as god.. I mean root.
    When I double click .bin, or write in a terminal or use sh with the name archive it doesn't run. (It sound so stupid)
    I do has instructions saids so I supouse is there some problem with the bin association/configuration, can anyone help me?
    Thank you and sorry for my english.

    It's been a while since I had a similar problem, and it might be something totally different than whats happening to you, but I had to add the chroot name and path to /etc/dchroot.conf
    arch32  /opt/arch32

  • Oracle Forms doesn't run because it can't read a file

    I can install Oracle Developer Suite 9i but Forms Developer doesn't run because it can't read file called "frmrow.res" or something like this. The other programs work just fine. This version of Developer Suite I have is from an original CD delivered to me by Oracle and it is translated into romanian language (i'm from Romania).Please help me. Thank you very much!

    That file is the romanian resource file for the runtime - Romaninan may be available in patch 1 I can't remember but you can just copy forms90/fmrusw.res to forms90/frmrow.res in the meantime to make it work.

  • Please help -- Why the applet doesn't run with jre1.4.1_01?

    Hi,
    I have an applet embedded in a remote-server page. It can be loading from the server and running in the local computer with Jre1.3.1. After I uninstalled jre1.3.1 and installed JRE1.4.1_01. My applet doesn't run. Here is the message from Java Consol:
    java.lang.NullPointerException
    at sun.plugin.cache.CachedFileLoader.writeHeaders(Unknown Source)
    at sun.plugin.cache.CachedFileLoader.createCacheFiles(Unknown Source)
    at sun.plugin.cache.CachedFileLoader.access$200(Unknown Source)
    at sun.plugin.cache.CachedFileLoader$3.run(Unknown Source)
    at java.security.AccessController.doPrivileged(Native Method)
    at sun.plugin.cache.Cache.privileged(Unknown Source)
    at sun.plugin.cache.CachedFileLoader.download(Unknown Source)
    at sun.plugin.cache.CachedFileLoader.load(Unknown Source)
    at sun.plugin.cache.FileCache.get(Unknown Source)
    at sun.plugin.net.protocol.http.HttpURLConnection.connectWithCache(Unknown Source)
    at sun.plugin.net.protocol.http.HttpURLConnection.connect(Unknown Source)
    at sun.plugin.net.protocol.http.HttpURLConnection.getInputStream(Unknown Source)
    at sun.net.www.protocol.http.HttpURLConnection.getHeaderField(HttpURLConnection.java:1197)
    at java.net.HttpURLConnection.getResponseCode(HttpURLConnection.java:247)
    at sun.applet.AppletClassLoader.getBytes(AppletClassLoader.java:250)
    at sun.applet.AppletClassLoader.access$100(AppletClassLoader.java:42)
    at sun.applet.AppletClassLoader$1.run(AppletClassLoader.java:143)
    at java.security.AccessController.doPrivileged(Native Method)
    at sun.applet.AppletClassLoader.findClass(AppletClassLoader.java:140)
    at sun.plugin.security.PluginClassLoader.findClass(Unknown Source)
    at java.lang.ClassLoader.loadClass(ClassLoader.java:299)
    at sun.applet.AppletClassLoader.loadClass(AppletClassLoader.java:114)
    at java.lang.ClassLoader.loadClass(ClassLoader.java:255)
    at sun.applet.AppletClassLoader.loadCode(AppletClassLoader.java:501)
    at sun.applet.AppletPanel.createApplet(AppletPanel.java:566)
    at sun.plugin.AppletViewer.createApplet(Unknown Source)
    at sun.applet.AppletPanel.runLoader(AppletPanel.java:495)
    at sun.applet.AppletPanel.run(AppletPanel.java:292)
    at java.lang.Thread.run(Thread.java:536)
    I copy the my html file which has this applet built-in to my local computer. The webpage can be openned and the applet running fine even with jre1.4.1. Why it didn't run with Jre1.4.1 and it did run with jre 1.3.1 when loading remotely? Could someone tell me what the above messages mean? Is this a bug from Jre1.4.1_01?
    I have running server at 206.29.25.29. and select "read sensor". Jre1.4.1_01 will not let the applet run, but jre1.3.1 does.
    Is there any body know about this issue?
    Thanks,
    Kunlun

    In fact, I have run many tests and the only failures are when the plugin is 1.4.2 and the app server is on Unix:
    Build      Deploy      Build JDK     PlugIn JDK     App Server JDK     Result
    Win     Win     1.4.2_02     1.4.2          1.4.2          Success
    Win     Win     1.4.2          1.4.2          1.4.2          Success
    Win     Win     1.4.1_02     1.4.2          1.4.2          Success
    Win     Win     1.4.2          1.4.0          1.4.2          Success
    Win     Win     1.4.2          1.4.1          1.4.2          Success
    Win     Win     1.4.2          1.4.2          1.4.2          Success
    Unix     Win     1.4.2          1.4.2          1.4.2          Success
    Unix     Win     1.4.2          1.4.2          1.4.1_02     Success
    Unix     Win     1.4.2          1.4.2          1.4.0          Success
    Unix     Unix     1.4.2          1.4.0          1.4.0          Success
    Unix     Unix     1.4.2          1.4.1          1.4.0          Success
    Unix     Unix     1.4.2          1.4.2          1.4.0          Failure
    Win     Unix     1.4.2          1.4.0          1.4.0          Success
    Win     Unix     1.4.2          1.4.1          1.4.0          Success
    Win     Unix     1.4.2          1.4.2          1.4.0          Failure

  • BootCamp Installer doesn't run

    Hi all, I have both a Summer 2007 MacBook Pro and an Al-iMac. When trying to install BootCamp with Windows Vista SP1 (x86) using the BC package in the Apple website (v.2.1), the installer doesn't run, just as if I haven't clicked the icon or something. It happens in both computers, and it doesn't run if I install the RC of Win7 either. It only works if I use the XP32 installer under WinXP SP3 in the iMac (in the MBP it doesn't run). I can't use the Leopard Service Disk of the iMac or the Retail copy because I lost both of them, and there's no BC in the Tiger Service Disks. Both macs use OSX 10.5.7.
    Is there any way to make them run or I have to use a MSP unpacker (I have found many unpackers for the MSI format, but none compatible for MSP) to get all the drivers out of the installer? Can I install the drivers by installing the Apple Software Update and downloading the packages from there? I've tried that on Windows7 but apparently it doesn't recognize the OS's version and the BC doesn't show up.
    PS: I'm not very good with English, so sorry if there's any error :P

    Hi Rorox,
    the 2.0 drivers are only avaiable on the OSX Leopard DVDs.
    IF you really have lost them (and not only misplaced them) you can call Apple and ask for a replacement.
    Have the serial number of your Mac at hand and usually Apple will charge your with about USD 30 for the replacement.
    Since the OSX DVD can also be sometimes vital for repairing errors of OSX you really should get a set.
    Regards
    Stefan

  • I have downloaded Indesign CC2014 and installed 3-4 times but it doesn't run. I have installed on  Windows 7 64 bit ,  HP laptop i7

    I have downloaded Indesign CC2014 and installed 3-4 times but it doesn't run /work. I have installed on  Windows 7 64 bit ,  HP laptop i7.

    sign out and then sign back in to your cc desktop app.
    then install cc 2014.

  • HT204150 After having upgraded to mountain lion, the application "contacts" doesn't run. I don't see any contact and add new contacts . The application doesn't run

    After having upgraded to mountain lion, why the application "contacts" doesn't run? Why is impossible add a new contact and I don't see old contacts that I can see on my Ipad?

    I have the same problem. I would like to include this information:
    .- A message "error CoreDAVerrorDomain 1" is shown
    .- with other user, in the same MAC I do not have the problem

Maybe you are looking for

  • Problem with xsd's

    hi, my scenario is file to idoc . coming to my problem is import multiple xsd's under one external defination from sender side. please can u give approach how to handle this? thanks, durga.

  • TS3276 how to configure Mail ?

    Hi ! How to configure Mail only to fetch a specific amount of messages on its first use? I'm using Mac OS X Lion 10.7.4 with Mail v. 5.2. Thanks a lot!

  • Latest version of Risk Management

    Can somebody please tell me when is the new version of risk management supposed to launch? Regards, Deep

  • How to upgrade iphone 3gs ios3.1 to ios4.1/4.3

    I have been trying to upgrade my iphone 3gs recently.. Unfortunately Itune keeps popping up the message box and stated that "There was a problem downloading the software for the iphone. The network connection timed out", It also required me to make s

  • How can I make the font size in my address bar smaller?

    On my laptop running Windows XP, Firefox 7, suddenly the font size on my tabs and in the address bar are huge. I have no idea what happened to make them that way. It's horrible.