Very high temp, but no problems at all!!!
Ok I got this k7n2-l last month. When I installed it with my 1800 xp, the temps would hover about 60 to 75 c. So I went and bought a new cpu cooler( therm vol 7) adn applied some artic silver 2. no change in temps. this cpu ran like 30 to 40c in my old k7s5a board with retail cpu fan. So I went and bought a xp 2200. and had them install it pro installed with retail cpu fan and thermal pad. now my temp hover between 70 and 100 c. the funny thing is I have never had a crash or any system problems what so ever. And I play counter-strike everyday. I ordered a ther volc 9 with some artic silver 3. But doesnt this seem weird. that I get these high temps and my system is very stable. I even oc'd the 2200 to a 2400 and get the same temp readings. I think the temp is wrong. Oh and I'm reading it from the bios and pc alert 4. what do you guys think?
With a Duron 800 and a Thermalright SK-5 and a 60 MM fan blowing about 12 CFM i was sitting around 120 F. I installed a Valcano 9 and the temp whent up to 131 F. I thougth i installed it wrong so i took it off, cleaned it and re aplied some Arctic Alumnia and the temp was stilla round 130 F. I took it off, put the SK-5 back on and it dropped to around 124 F. I took the 80 MM fan off the Valcano 9 and placed it on the SK-5. The temp whent down to around 118 F. Needless to say the Valcano 9 heatsink is a peice of . Or my first generation old ass SK-5 is badder asser. But i dought that seeing the I was getting the same temps with a $8 CoolerMaster.
Now with my Athlon 1700+ @ 195x10 I hover around 127 - 131 F with the Thermaltake fan from the Valcano 9 at its lowest setting, compleatly silent, spinning about 2500 RPM's.
I attached the sensor from the Valcano 9 to the bottem of the Proc whith some thermal tape. With a little re-wiring i ran it into my Vantec NXP 201. What ever it reports is usally around 3 - 5 C lower then the Bios. Usually around 48 C. I thought the Bios temps where way off. But now lookign at it i'm not so sure they are. If the temp in the Bios is being taken fromthe core of the Proc and the temp on the Vantec Nesus is being taken from the bottom of the proc, and theres only a free degrees difrence, i'm not sure the Bios is wrong.
This is on an ILSR BTW..
Similar Messages
-
Hello, i have a problem with my MSI GNB MAX motherboard and my p4 3,06 ghz
My cpu temperatures are very high, with a maximum of 85/86c,,, is this normal??
Anyone else having a similar problem like this?
MSI GNB MAX (ms-6565) motherboard
P4 3,06 ghz processor with standaard p4 cooler
1024 mb DDR 266 mhz (dual) memory
Geforce 4 mx videocard
60Gb Maxtor ATA133 HD
Promedium Mars case with a total of 6 fans
(not overclocked)If Vcor is 1.4 (I'm running 1.525 but reads 1.47 in PCAlert), AND fsb is set for 134, AND your HSF is running AND has good contact, there is no way for it to be that hot. The stock HSF is a pretty good part. I would suggest getting a temperature probe and touching it to the base edge of the HSF to see if you are really that hot. In Bios, I have the cut off threshold at 65C and alarm at 63C. I dont know the exact conversion but 86C is near hot enough to boil water. The laquer from the chip would probably begin to melt and create an odor.
-
Ipod classic won't sync to itunes on PC but no problem at all with MAC
Hi,
i have this problem for almost a year now. i have tried restoring my ipod (using both itunes & ipod restore option) i have uninstalled and reinstalled itunes, checked it with different computers and different operating systems (XP and windows 7) and the problem is still not solved.
Here is the problem:
if i'm connecting my ipod to mac, i can restore it and sync it with no problem at all. but when i'm connecting the same ipod to a PC, i than need to restore my ipod, which is fine, but after restoring, my ipod will not sync to itunes either on a PC or mac. but if again i'n restoring my ipod on mac, i can than sync again with no problem at all (but than i need to restore it on PC and again it can't be synced). any suggestion as to why is it happening? i'm using the latest version of itunes.
Thanks,
FloraOne question; was there any music on the iPod before now, and if so, what happened to it?
Check to make sure that Sync Music is selected on the Device/Music pane and that you have selected music to be added to the iPod. -
Do all the PowerBooks get to very high temps?
My PowerBook G4 gets to 185 (85 celsius)
My PowerBook G4 gets to 185 (85 celsius)
Hello Victor,
85°C? Wow! That's way too hot, at least for the 12" model. The fan is supposed to activate at 60°C. Recently my 12" PowerBook's fan has not activated - and my PB is overheating too, up to 72°C after 10-15 minutes of 100% CPU load running Folding@Home.
Let's try to help each other since no one else is answering our questions.
- Do you hear fan noise from your PB when it gets very hot?
- How are you monitoring the temperature? (I use X-Resource-Graph)
- What application(s) were you running when your PB heated to 85°C? Do you know the %CPU utilization? (as you may know already, you can see this in Activity Monitor)
- What was the last software update you installed on your PB?
- What did you do when you noticed how hot your PB was? Did you shut it off, or did it go to sleep by itself?
Thanks Victor - I'm sure that if we get a good thread going here, we can figure out these overheating problems.
Best wishes,
Jean
PowerBook G4 DVI 867 MHz Mac OS X (10.3.9) 640 Mb RAM, original 37+ Gb hard drive. Usually running Folding@Home (cpu-intensive) -
GT60 0NE new EC getting very high temps
Hi , i have a GT60 0ne with gtx680m. I just update the firmware n bios but the new EC which i download (16F3EMS1.413.zip) from the msi site is making my gpu pretty hot. Temps used to be 79-80 on full load and
now my highs are like getting onto 90s and it seems the fan doesnt scale very well with the temps. It is much more quiet in fact after the new EC update but its making my gpu running like an oven.
Any advice or help would be appreciated.
Thank youQuote from: trigger25sg on 24-November-12, 05:20:18
Hi flobelix and thanks for the clarification. I just flashed back the old EC from msi china as most msi sites have been updated with the new EC. Yup its loud but i think i have more peace of mind.
Thank you.
which old version is this? -
GeForce NX8600GTS-T2D256EZ, Very High Temp; should I be concerned?
Hello,
I have the MSI GeForce 8600 GTS NX8600GTS-T2D256EZ-HD. I just opened the case and realized it runs really hot; I can barely touch the copper pipes or the aluminum heat sink. I have a Silenex Fan right under it and some air flows over the surfaces. For reference, the 975X chips/heat sinks are near room temp.
Anyone notice this issue? Should I be concerned about a video card in the computer that run this hot? If so, any suggestions for cooling? I have P182 case and 5 fans.
ScottQuote from: jsmartin22 on 15-July-07, 13:41:39
Had no idea what these were, but searched/read. Downloaded & installed Nvidia Ntune, which added features to the control panel, including temp monitoring. GPU Temp is 48c, and I can't imagine that is an issue, right?
Thx for the good suggestion; I appreciate it!
Scott
nop, GPU can running very hot without to worry about. 80-90C underload temp can be expected.
if you don't have real issues don't worry about the temp. -
Over the last few months my Mac has developed a worrying habit.
Within the first few minutes of starting it up (perhaps on average about 50% of the time) it will completely lock up. This may happen at the Log In screen (if I start up the Mac & then leave it for a while) or during normal use.
Often the first symptom is a very high pitched (but quiet) whining noise that seems to come from the loud speaker on the front of the Mac. The pointer may freeze at this point, or it may still be moveable for 5 or 10 seconds before it freezes. It sometimes turns into the spinning beach ball during this. Once locked up the only way I can restart the Mac is to hold down the power button on the front for a few seconds to completely reboot the machine.
Once the Mac has restarted, it usually behaves normally, almost always for the rest of the day. The initial lock up & resulting restart only normally seem to happen the first time I use the Mac that day.
The only peripherals attached to the Mac (apart from the display, keyboard & mouse) are an ADSL modem, a USB printer and a pair of Apple Pro speakers, and this setup hasn't changed since long before the problems started, so I'm confident that I can discount the peripherals causing problems. I doubt that unplugging the speakers, for example, would have any effect.
I've run Disc Utility, OnyX and DiscWarrior without anything major cropping up. My instincts (I've been troubleshooting Mac problems for 16 years) tell me that I have a fundamental hardware problem, possibly with one of the 4 RAM DIMMs installed.
The RAM configuration is shown in the attached screen grab.
I'm considering removing one DIMM, running with 1.5GB of RAM rather than 2GB for a while, and repeating with a different DIMM removed each time until I can hopefully isolate the dodgy DIMM.
Do people feel this is a sensible approach, or should I try something else first?
Many thanks.Sometimes visual inpection will show bulging tops/sides., my guess is if it is it's most likely in the PSU.
Possible cheap fix, You can convert an ATX PSU for use on a G4...
http://atxg4.com/mdd.html
http://atxg4.com/ -
P7N SLi, Very High NB / SB / PCI Express cooler.
I noticed that i have very high temps on my mobo, when i have my finger on the NB / PCI express cooler over 1 sec i i feels like a have in in fire?
This cant be good!
what shall i do?did you install the right one it has 32 and 64 bits ?? please double check
http://s240.photobucket.com/albums/ff177/kourosh22/?action=view¤t=ScreenShot041-1.jpg
mine is ok -
firefox is working my system too hard and the system is revving very high.
== This happened ==
Every time Firefox opened
== today ==
== User Agent ==
Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10_5_8; en-us) AppleWebKit/531.22.7 (KHTML, like Gecko) Version/4.0.5 Safari/531.22.7Does this start right when you start firefox or after you've loaded some pages? Are there specific pages that cause this problem?
-
I am trying to do a full Time Machine Backup to a new external disk. The backup starts, and it says "Time remaining about 4 days." That seems like a very long time, but the real problem is that the computer "logs off" after a few hours, and the backup stops. The system preferences are set to "Never" for Computer sleep and Display sleep. The computer does not ordinarily log off automatically, but it has done this twice since I started the Time Machine backup.
If you have more than one user account, these instructions must be carried out as an administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Enter the word "Starting" (without the quotes) in the String Matching text field. You should now see log messages with the words "Starting * backup," where * represents any of the words "automatic," "manual," or "standard." Note the timestamp of the last such message. Clear the text field and scroll back in the log to that time. Select the messages timestamped from then until the end of the backup, or the end of the log if that's not clear. Copy them (command-C) to the Clipboard. Paste (command-V) into a reply to this message.
If all you see are messages that contain the word "Starting," you didn't clear the search box.
If there are runs of repeated messages, post only one example of each. Don't post many repetitions of the same message.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Some personal information, such as the names of your files, may be included — anonymize before posting. -
Apple has a problem and the cant solve it. I had some very important call but this new iphone just shut down on me and wont turn on i tried everything u can find in apple support nothing works for me. Anyone know what i can do?
I would instead say you have a problem since nearly all IPs work as advertised. IF you do have a bad phone, take it into an Apple store and get a replacement. Hope you didn't jailbreak your phone though as Apple probably will tell you, you broke it, you fix it.
-
My iMac is less than one year old. Without warning, the screen suddenly goes black. It used to happen ocasionally, but now it happens all the time. Numerous people have posted about this issue. Why hasn't Apple solved the issue. For what I paid my computer, I expected more from the product than I have gotten. I was a PC person for years and most of my associates told me that I needed to get a mac...I am starting to regret having taken their advice.
Sorry you're having this problem.
A few years ago we had a similar issue on one of our machines, it was an early MacBook. Ended up being a cracked circuit connection on the motherboard. Changes in temperature caused the crack to expand and contract resulting in a shut-down followed by an automatic reboot. Sometimes over-and-over. I understood from AppleCare at the time that those symptoms could have also been any number of things including a intermittent issue with a powersupply.
If you take it back to the Apple Store at some point, I would ask them to have it run some CPU intensive tasks that closely resemble what you are doing when the screen goes black. It took us several try's to find the problem. Calling AppleCare each time to discuss it and troubleshoot before making the trips to the Apple Store really moved things along. In fact, it wasn't until the Apple Store had cracked the case from the inside that things kicked into a higher gear and AppleCare phone support sent out a pre-paid FedX package to send it to a refurbishing facility. Never a problem since and I know the people who have the machine today.
PS Can identify with the trip to the Apple Store, our closest one is in Knoxville, 2hrs from us. -
What is best all in one printer for my new MacBook Pro ? Needs to make very high quality photos.
What is best all in one printer for my new MacBook Pro ? Needs to make very high quality photos. Using USB connection.
That's a difficult one but I'd always go for HP as they make so many excellent models that you'll always be able to buy the cartridges from almost anyone. Theyre darn good printer too. I have four in the office here and one of them is a very neat flatbed with exceptionally high tonal qualities. One of their cheaper models is the HP 5520 A4 inkjet all-in-one - CMYK. Good value at £70 and 4800 x 1200 DPI.
-
sir i have given lot of effort but i am not able to solve my problem either with notifiers or with occurence fn,probably i do not know how to use these synchronisation tools.
sir i am using datasocket read ,i am communicating with java but my problem is that bcz im using while loop to see if value has changed my labview consumes all the processors time ,sir i want a event like thing so that while loop is not in continuous loopHi Sam,
I want to pass along a couple of tips that will get you more and better response on this list.
1) There is an un-written rule that says more "stars" is better than just one star. Giving a one star rating will probably eliminate that responder from individuals that are willing to anser your question.
2) If someone gives you an answer that meets your needs, reply to that answer and say that it worked.
3) If someone suggests that you look at an example, DO IT! LV comes with a wonderful set of examples that demonstate almost all of the core functionality of LV. Familiarity with all of the LV examples will get you through about 80% of the Certified LabVIEW Developer exam.
4) If you have a question first search the examples for something tha
t may help you. If you can not find an example that is exactly what you want, find one that is close and post a question along the lines of "I want to do something similar to example X, how can I modify it to do Y".
5) Some of the greatest LabVIEW minds offer there services and advice for free on this exchange. If you treat them good, they can get you through almost every challenge that can be encountered in LV.
6) If English is not your native language, post your question in the language you favor. There is probably someone around that can help. "We're big, we're bad, we're international!"
Trying to help,
Welcome to the forum!
Ben
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction -
I have just updated to Yosemite, but now I can't get the custom short-keys to work.
In Mavericks I had no problem whatsoever, but now even after googeling and restart no solution.
Does anyone have the problem? All the other shortcuts work!Hi Thomas,
I can confirm the problem you are hitting. The XML test trace does not get recognized at all, and it defaults to Eclipse's basic Open File behaviour. I am not sure if it's because the format definition is missing, or if it's because something prevents the trace type from being recognized. I will open a bug about it.
Thanks for identifying this issue!
In the meantime, if you'd like to experiment with XML analyses, you can also take a look at the example at https://github.com/tracecompass/xml-analysis-example .
Cheers,
Alex
Maybe you are looking for
-
Bapi or function module for Tcode F-54
Hi, I need Bapi or Function moudle for tcode F-54. I am developing interfaces. I have to clear the the advance amount against an invoice. Regards, Dhanunjaya Reddy.
-
How can I get my HD video to work on my computer?
I shoot HD video on a JVC camera. I'm on a new computer at a new job. The computer won't play the video in anything but VLC Player. VLC says the video codec is Mpeg-1/2 Video (xdv1). What do I need to do to play the video in Quicktime and Final Cut?
-
Competitor in customer search tab in CIC0
Hi, In CIC0 we have customer search tab which contains the details of customer search. I want to add a field of competitor in that screen. This field will indicate wheather this customer is competitor or not. Please help. Regards, Dhanraj Dange Messa
-
How to make the text displayed on JLabel verticaly
As the Titile! thanks a lot
-
Hi, i just updated to the latest aperture, i have projects previously saved on a drive (in the old version) that now won't load... how do i update them?