Very low signal with new WRT54G (V7.2) comparing with my old BEF1W1154

I bought myself a new WRT54G router to replace my old (but good working) b-router. With the old router I have a great signal in/outdoors.
With the new g-router I experience a low signal , even in the room were I installed the router. In other rooms or outdoors I don't have a signal at all.
Please advice

There are many causes for poor wireless connections, and many solutions:
First of all, give your network a unique SSID. Do not use "linksys". If you are using "linksys" you may be trying to connect to your neighbor's router. Also set "SSID Broadcast" to "enabled". This will help your computer find and lock on to your router's signal.
Poor wireless connections are often caused by radio interference from other 2.4 GHz devices. This includes wireless phones, wireless baby monitors, microwave ovens, wireless mice and keyboards, wireless speakers, and your neighbor's wireless network. In rare cases, Bluetooth devices can interfere. Even some 5+ GHz phones also use the 2.4 Ghz band. Unplug these devices, and see if that corrects your problem.
In your router, try a different channel. There are 11 channels in the 2.4 GHz band. Usually channel 1, 6, or 11 works best. Check out your neighbors, and see what channel they are using. Because the channels overlap one another, try to stay at least +5 or -5 channels from your strongest neighbors. For example, if you have a strong neighbor on channel 9, try any channel 1 through 4.
Also, try to locate the router about 4 to 6 feet above the floor, in an open area. Do not locate it behind your monitor or near other computer equipment or speakers. The antenna should be vertical.
Also, in the computer, go to your wireless software, and go to "Preferred Networks" (sometimes called "Profiles" ). There are probably a few networks listed. Delete any network named "linksys". Also delete any network that you do not recognize, or that you no longer use. If your current network is not listed, enter its info (SSID, encryption (if any), and key (if any) ). Then select your current network and make it your default network, and set it to automatic login. You may need to go to "settings" to do this, or you may need to right click on your network and select "Properties" or "settings".
If the above does not fix your problem, download and install the latest driver for your wireless card.
Some users have reported improved wireless performance by switching to WPA encryption.
If you continue to have problems, try the following:
For wireless g routers, try setting the "Transmission Rate" to 54 Mbps.
If you still have trouble, download and install the latest firmware for your router. After a firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.
Hope this helps.

Similar Messages

Very low signal strength when using DLINK 2640t with mac mini

i have a mac mini and i have been using it fine with a 2wire wireless modem. However i have just switched to a Dlink 2640t (54Mbps (802.11g) Wireless ADSL 2/2+ Router with Built-in Modem, 4-port 10/100Mbps Switch) and have been getting very low signal strengths on my mac mini, resulting in me not being able to surf the internet. The modem+ router is located in the next room. Does anyone know whether its the problem with the modem router or mac mini's airport wireless problems with the router itself. It worked perfectly fine with my previous 2wire wireless modem
please help!

Did you reset the router after you updated router's firmware? Its always recommended to perform a reset after firmware upgrade on the router.
Please refer to the link http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=eaa3127db5f4402584c959a7251e754c_4008.xml&pid=80&r...
For wireless range and signal issues, try changing the channel on the router to either 1,6,9 or 11.
Please refer to this link on changing wireless channel and SSID (network name)
http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=a0fb6c64337e47eb9e3e1027f364e70c_154.xml&pid=80&re...

Orig iPhone call drops & very low signal w/ latest update since 3GS release

For those who have the original iPhone...have any of you been experiencing A LOT of dropped calls and also VERY LOW signal, like 1 & 2 bars? Not just in certain areas either but EVERYWHERE.
After the 3GS release an update of iPhone software was released some time later for the older phones. After I updated my original iPhone to the latest software release through iTunes after the 3GS release my original iPhone now has very poor signal and a lot of dropped calls. I've visited several AT&T stores for resolution. There insufficient answer, perform a network reset. I do this several times a day and it has no positive effect. I still drop calls, some calls don't connect and extremely poor signal.
I also noticed that the internet is working slower, both using the Edge network and the wireless in my own home.
Moreover, I've been researching the internet and finding a lot of other people experiencing the same issues. Mostly becuase the new 3G & 3GS are media hogs eating up the resources & capacity of AT&Ts network capabilities. I've even found that there are 2 class action lawsuits against Apple & AT&T about the poor network operation, tethering limitation and Apple not allowing Google to post an app on iTunes store.
I think the orginal iPhone updated to the latest software release from iTunes that is meant for 3G & 3GS is causing the poor performance to the original iPhone. I know dropped calls & poor signal is AT&T's responsibility but I feel that Apple has an obligation to it's customers to make sure all models, including the original iPhone, are up to par or above average performance when releasing new software, firmware & hardware. I think at this time Apple & AT&T have not completely verified and validated that the original iPhone still performs well with the 3G & 3GS updates.
If Apple or AT&T or both don't remedy my phone network issues to prevent dropped calls and improve the very poor signal then I will be selling the iPhone and switching to a Blackberry with Verizon service. I had Verizon before and ONLY dropped calls in 2 deadspots. I could bet my life I would drop a call driving through that zone, but so does T-Mobile & AT&T. Other than that, Verizon is without a doubt the best cellular service I have had.
Get with the program Apple & AT&T, make your customers happy and fix the network issues so original iPhone users won't leave AT&T to other services. Note, I was thinking of spending $300 and upgrading to the new 3GS but now I'm thinking of spending less and switching to a Blackberry with a more reliable cellular service, Verizon.
So, is Apple & AT&T going to lose another valuable customer?
P.S.
Yes, I paid $600 for my 8GB original iPhone. Loved it til now. Geez, I'm ashamed to say Apply may have finally made a bad product that does not stand the test of time.
Best Regards,
Greg Light

Please excuse some of the typos. It's late and the browser shut down on a me a few times.

ADAT into Logic Express, VERY low signals recorded

I tried Garageband, same problem, so now I am trying Logic Express.
When transferring tracks from an ADAT, through Alesis io/14, into Logic, the resulting sound files captured are VERY low signal. This should be a digitally ACCURATE TRANSFER. The Alesis montoring software on the mac senses the correct signal, the signal meters show correct levels (and sounds great), but Logic hears and records very low signals.
I note the Sound midi pref window only shows 6 channel 32 bit. It won't allow me to change to 8 channel 16 bit. Possible problem or am I chasing ghosts? I exhausted all my ideas.
Any thoughts?
T

Ropher wrote:
Discovering I was unable to import a ".au" file into Logic Express (or Garage Band) I read it into Sound Studio and exported it in a variety of formats. I can now successfully drag to Garage Band files in formats .aif .aifc .sd2 and .wav and get the expected result.
Unfortunately however, I only get the expected result importing these into Logic Express for the .aifc format which plays back at the expected speed with a low-pitched sound (but which doesn't display an uncompressed waveform). Importing the .aif .sd2 or .wav format files however results in the imported file being squeezed into a very short duration with a correspondingly undesirable very high pitch.
Is there some setting or magic incantation I need for reading in audio files to Logic Express without it getting squeezed?
Thanks!
--Roph
Yes. you need to ascend to level 5 before we give that secret incantation.
Really, you need to use a third party converter software, if you are going to use .au files.
Logic is happiest with .aiff, .wav files, but not much else.
Cheers

I'm getting a very low signal from my Blackbird interface. The fire wire connection is selected properly and track recording sliders set. However the recording level slider in the lower right corner is grayed out. How can I get better signal?

I'm getting a very low signal from my Blackbird interface. The fire wire connection is selected properly and track recording sliders set. However the recording level slider in the lower right corner is grayed out. How can I get better signal?

If it's slow on startup it would be extensions loading or LaunchDaemons starting up.
You should have a look in:
/Library/LaunchDaemons
/Library/Extensions
You can count out anything in your home folder and it shouldn't put anything in /System as that's reserved for Apple.

When opening my Outlook 2010 with new added e-mail account with Exchange Server, I have to click manually on my standard e-mail account for checking mail

When opening my Outlook 2010 with new added e-mail account with Exchange Server supplied by my employer, I have to click manually on my standard e-mail account for checking mail. Do I have to upgrade my Microsoft Office 2010 or how can I make my Outlook
2010 check all my four e-mail accounts without manually click on my accounts?
Sincerely
Ketil Hothorp

Hello Ketil,
Good Day...
Seems to be the Issue is Syncing emails, now I would recommend you to Remove and Add the Account and try and check if the emails are getting synced automatically.
Hope this is with Single User. If it is with Multiple Users then we need to check the permissions assigned.
Regards,
Praveen

Why does iMessages does not work properly ? Please help me ! Its works better with the previous version if compared with the latest iOS

Why does iMessages does not work properly ? Please help me ! Its works better with the previous version if compared with the latest iOS

Many, many thanks for both of you Todd and Rick.
to Rick:
I suppose you mean the Color Settings in Project Settings as follows:
- Working Space: None
- Match Legacy ... Gamma Adjustments checked ON
But it does not correct the colors in effects. And checking or unchecking Make Movie/Output Module Settings/Color Management/Profile/Preserve RGB does not make any difference.
to both of you:
Those parts of the video image that does not have color effects are just fine. In these parts the color is preserved when reimporting to FCP. However, those parts having color effects (except Levels, as decribed earlier) have altered color results. So, only the parts having effects affecting color are misinterpreted in the image area. The mismatch is of course seen in AE, before making the movie.
What I ment with "Color Management not working properly" is that (instead of "disabling" it) Color Management does not seem to be able to correct this "misinterpretation" or difference in effect handling between AE 6 and 10.
So, would you have any solution for this problem?
Again, many thanks for your fast replies!

M-Audio FastTrack USB - very low signal level (line/guitar)

I've used FastTrack USB for a couple of years with a microphone through the XLR input with no problems. Now I am trying to connect a line output of a synthesizer to the line input of the FastTrack and the signal level is very low. There is no noise, it's just quiet, even with the track volume all the way up it's still no match for the rest of the tracks.
Any suggestions, except for trying all the knobs and switches on the face and back of the unit (tried that already)? Anybody has similar setup?
I use FastTrack for audio input, and built-in audio for output, it's connected through a hub (no problems for two years). In GB microphone is going to the Channel 1 (mono), and still works fine. Synthesizer goes to Channel 2 (mono) and is really quiet. I tried the syn with two different 1/4 cables with no difference. The headphones jack on the front of the FastTrack works fine with the normal level adjustment range, and if I plug in the headphones directly into the line out of my syn, I have sound, quiet (like you would get by connecting headphones to any line out, turntable even) but steady, so the syn must be fine.
Any thoughts?

No takers. Hm. OK. After some more research on the Net it appears to be that all the Fast Tracks suffer from the same problem, which makes me believe that it's not a bug, but a feature of an unexplainable kind. Oh, well, back to my old iMic noisemaker (this one works, it's just screened very poorly, so it picks up all the possible interference, and also makes its own little nasty hiss--this is why I switched to the Fast Track a while ago--so I will need to cut it out with an EQ, again). Hopefully, the EQ surgery will not affect the synthesizer's sound consistency as severely as it use to do with a microphone.

HT204405 The ringing voluom is very low on my new iPhone 5s

THe ringing voluom is very low on my phone , is it the phone or the soft wear , I just bought the phone 2 days ago

Hi Nouraldeen,
Welcome to the Support Communities!
As a first step, I would suggest restarting and/or resetting the iPhone:
iOS: Turning off and on (restarting) and resetting
http://support.apple.com/kb/HT1430
Here are some additional troubleshooting steps for sound on your iPhone:
iPhone: Can't hear through the receiver or speakers
http://support.apple.com/kb/TS1630
Cheers,
- Judy

Hello.With new browser I can't see saved old browser page

With new firefox 4.0 i can't open, with old version 3.6 saved pages. If I try to open saved site, browser 4.0 show wite page.
== This happened ==
Every time Firefox opened

Start Firefox in [[Safe Mode]] to check if one of your add-ons is causing your problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
See [[Troubleshooting extensions and themes]] and [[Troubleshooting plugins]]

Itunes very slow in Middle East region recently.(compare with first of Oct.)

I am in Middle East region, and i feeling that the itunes speed became too slow compare with one month before...Maybe IOS6 downloading effect?

I am in Middle East region, and i feeling that the itunes speed became too slow compare with one month before...Maybe IOS6 downloading effect?

Booted off Broadband connection with new WRT54g Wireless Router

I recently moved to a new place with Comcast Broadband. My boyfriend and I both want to access the Internet so we got a Linksys Wireless Router to connect our computers to the broadband connection. It's not going very well, however, because almost daily we are booted off the Internet. I called Comcast and they said the Modem is working fine, which just leaves the Router. Does anyone have any suggestions on what might be causing this?
Thanks,
Patricia

How did Comcast determined that your modem is working fine? When you are connected directly to modem , do you have the same problem? because if you do, then it would have the same problem with the router, no matter what you do with the router. Try isolating problem by checking if the connection would drop when you are connected directly to modem.
If through isolation process you found out that modem is stable, there might be a problem with router itself or that the router isn't properly configured, is your computer wired or wireless? how about your boyfriend's?
" I can do all things through Christ which strengthens me. "

Very low signal reaching Apple TV

Is there a way to boost the Apple TV antenna? I only have a one bar signal, but I can't move the router (d-link 802.11n) from it's location downstairs, and can't move the Apple TV from it's location upstairs. (An ipod or laptop, when used in the same room as the Apple TV location, have no problems with the WiFi.)

The Apple TV quite likely has more equipment near to or around it that might cause some level if interference. You might consider connecting it by Ethernet or power line adapters.

Swapping HDs with new MBP: What to do with OS X?

I purchased a new MacBook Pro 2.3GHz i7 quad-core from the Apple Store Thursday morning with the 750GB 5400RPM hard drive. I now have time to set up the new machine but I am hung up on how best to deal with swapping hard drives. My current MBP has a 640GB 7200RPM hard drive with OS X 10.6.6 installed. I am a photographer so the faster drive makes a big difference with large photo catalogs. I had planned on swapping out the new 750GB 5400RPM drive for my current 640GB 7200RPM hard drive and then get back to work, however, I am concerned that the OS X installed on the 640GB 7200RPM hard drive will not be compatible with the new machine's processor. Should I do the swap and then boot up from the new laptop's OS X install disks and do a OS X only install? I have never done a OS X only install/update, will any other data be altered, any suggestions on how to proceed? Should I just swap, start up and then run Apple Software Update?
I would prefer avoiding an erase and install, cloning, migration, Adobe registration issues, etc and going the HD swap and OS X disk update route if it can work.
Thanks for your input,
Chad

I found this discussing looking to do the same thing-ish.
I just bought a new i7 quad MacBook Pro (delivered today). Less than 4 weeks ago, I had picked up an i5 MacBook Pro. Since I'm still in my return window, I decided the buy the new one, do the hard drive shuffle and return the less new one.
I have a 500gb 7200rpm drive AND a 120gb SSD in the drive bay. I really never considered just swapping the drives into the new machine, but I thought I'd search and see if anyone had any success.
I had a couple thoughts on how I'm going to do the shuffle:
1) Superduper clone the SSD back onto my 500gb. I the system as it is now started life on the 500gb. Superduper (registered) will do a backup only updating the changed files which shouldn't be too bad. I have my user directories (separate from the startup disk) on the 500gb so SD won't have to copy any of those files. Then I figured I could use the migration software to copy all my 'stuff' (minus user directory) back onto the newly reformatted SSD with 10.6 installed onto the new MBP.
2) I was noticing that migration assistant can work from Time Machine, so I'll probably do that since my SSD time machine backup doesn't contain my gigantic user directory. I'll still do a SuperDuper backup just to be safe.
I'm tempted to throw my hard drive into an external usb to see if it boots just for the heck of it.

Old computer was stolen. Replaced with new. Reestablished I-tunes account. Old downloads are still in Cloud how do I get them back without having to repurchase

My computer was stolen and I have replaced it. I reestablished my acount with I-Tunes. All of the music that I had purchased is still listed in my acount but how do I get them back without having to pay again?

Look here: http://support.apple.com/kb/HT2519
To download previously purchased apps, books, music or TV Shows to your computer
Open iTunes 10.4 or later on your computer. (You can download the latest version of iTunes here.)
If you're not already signed in, click Sign In and enter your Apple ID and password.
After you've signed in, click Purchased on the right side in the iTunes Store under the QUICK LINKS the section.
From your Purchased page, click the tab for the content type you're looking for (Music, TV Shows, Apps, or Books).
Click Songs or Albums to change the page view and All or "Not in My Library" to view your purchased content that currently is not downloaded on your computer.
Click the download icon to the right of each item to download that item.
Note: Previously purchased music is only available through iTunes in the Cloud in Australia, Canada, Cypress, France, Ireland, Luxembourg, Malta, Mexico, New Zealand, Spain, the United Kingdom, and the United States. Previously purchased TV shows are only available through iTunes in the Cloud in the United States.Notes:
To download previous purchases on a computer, your computer must be authorized for the Apple ID that was used for the original purchase. For more information about iTunes Store authorization and deauthorization see,this article.
Items that have been refunded by iTunes Store support cannot be downloaded again and will no longer show on your Purchased page.

Very low signal with new WRT54G (V7.2) comparing with my old BEF1W1154

Similar Messages

Maybe you are looking for