Very slow connection?... help please.

hi, this is my first post on the forum and i'm basically after some advice as to whether i'm likely to improve my broadband speed?
I live in Suffolk, some distance away from the local exchange, although i know that other people in my village have a faster broadband service than i am currently getting.
I have tried various things over the last few months including phoning BT and having them do various tests and resets on my line assuring me of an improved service but to no avail?
I've also followed advice on this very forum and put in a shielded wall socket booster, a high speed dsl cable and exchanged my hub for the business hub.......
for the record, i only have one phone socket in my bungalow, so extension wiring isn't a problem.
i'll post the results of my hub status and speedtest results below and if someone could shed some light on these figure, i would be hugely appreciated.
thanks in advance
Simon
SPEEDTEST RESULTS:
Download speedachieved during the test was - 315 Kbps
 For your connection, the acceptable range of speeds is 50-500 Kbps.
 Additional Information:
 Your DSL Connection Rate :1184 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
 IP Profile for your line is - 350 Kbps
SUMMARY STATUS:
Summary Status
DSL Link:   Connected
Internet:   Connected
Internet Details
Broadband Link Type: Built in modem - ADSL
Connection Type: PPPoA
User Name: [email protected]
Current Internet Connection: 
IP Address: 86.132.32.113
Subnet Mask: 255.255.255.255
Default Gateway: 217.47.66.141
Primary DNS: 217.32.171.21
Secondary DNS: 62.6.40.166
Host Name: 
Domain: 
MAC Address: --:--:--:--:--:--
MTU: 1500
DSL Details
Modem Type: Built in modem - ADSL
DSL Line (Wire Pair): Line 1 (inner pair)
Current DSL Connection:
                                 Down           Up
Rate:                      1184 kbs      448 kbs
Max Rate:                1184 kbs      824 kbs 
Noise Margin:            9.0 dB         17.0 dB 
Attenuation:             61.1 dB       31.5 dB 
Output Power:          16.4 dBm  11.9 dBm
Protocol: G.DMT Annex A
Channel: Interleaved
DSLAM Vendor Information Country: {3840} Vendor: {ALCB} Specific: {0 } 
ATM PVC: 0/38
Rate Cap: 1184 kbs
Attenuation @ 300kHz: 61.1 dB
Uncanceled Echo: -7.1 dB Ok
VCXO Frequency Offset: 27.1 ppm Ok
Final Receive Gain: 34.5 dB Ok
Impulse Noise Comp. Tones: 0 Ok
Excessive Impulse Noise: 0 Ok
Traffic Statistics
IP Traffic Bytes Packets Errors %
Transmit: 34516782 322969 0 0
Receive: 434170014 377821 0 0
ATM Traffic Cells Errors %
Transmit: 972725 0 0
Receive: 9331356 0 0
DSL Link Errors
Collected for 16:16:33
 Since Current Current Time Since
 Reset 24-hr int. 15-min int. Last Event
ATM
Last Event
Cell Header Errors 472 472 1 0:00:01
Loss of cell Delineation 132 132 0 0:16:53
DSL
Link Retrains: 1 1 0 4:55:22
DSL Training Errors: 0 0 0 0:00:00
Training Timeouts: 0 0 0 0:00:00
Loss of Framing Failures: 0 0 0 0:00:00
Loss of Signal Failures: 0 0 0 0:00:00
Loss of Power Failures: 0 0 0 0:00:00
Loss of Margin Failures: 0 0 0 0:00:00
**bleep**. Seconds w/Errors: 226 226 1 0:00:01
**bleep**. Sec. w/Severe Errors: 6 6 0 2:03:45
Corrected Blocks: 35786 35786 332 0:00:01
Uncorrectable Blocks: 581 581 1 0:00:01
DSL Unavailable Seconds: 65 65 0 4:54:57

you say you fitted a 'shielded wall socket' do you mean a filtered faceplate like this 
you can also check this post for ideas which may help  
http://community.bt.com/t5/BB-in-Home/Poor-Broadband-speed/m-p/14217#M8397
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Similar Messages

  • Macbook Pro is Running very Slow. Help Please

    My Mac is running very slow does anyone have some tips please
    EtreCheck version: 2.1.8 (121)
    Report generated March 9, 2015 9:43:12 AM GMT+02:00
    Download EtreCheck from http://etresoft.com/etrecheck
    Click the [Click for support] links for help with non-Apple products.
    Click the [Click for details] links for more information about that line.
    Hardware Information: ℹ️
        MacBook Pro (15-inch, Late 2011) (Technical Specifications)
        MacBook Pro - model: MacBookPro8,2
        1 2.4 GHz Intel Core i7 CPU: 4-core
        4 GB RAM
            BANK 0/DIMM0
                2 GB DDR3 1333 MHz ok
            BANK 1/DIMM0
                2 GB DDR3 1333 MHz ok
        Bluetooth: Old - Handoff/Airdrop2 not supported
        Wireless:  en1: 802.11 a/b/g/n
        Battery Health: Normal - Cycle count 126
    Video Information: ℹ️
        AMD Radeon HD 6770M - VRAM: 1024 MB
            Color LCD 1440 x 900
        Intel HD Graphics 3000 - VRAM: 384 MB
    System Software: ℹ️
        Mac OS X 10.7.5 (11G63) - Time since boot: 0:49:54
    Disk Information: ℹ️
        APPLE HDD HTS547575A9E384 disk0 : (750.16 GB)
            disk0s1 (disk0s1) <not mounted> : 210 MB
            Macintosh HD (disk0s2) / : 749.30 GB (321.70 GB free)
            Recovery HD (disk0s3) <not mounted>  [Recovery]: 650 MB
        MATSHITADVD-R   UJ-8A8 
    USB Information: ℹ️
        Apple Inc. Apple Internal Keyboard / Trackpad
        Apple Inc. BRCM2070 Hub
            Apple Inc. Bluetooth USB Host Controller
        Apple Inc. FaceTime HD Camera (Built-in)
        Apple Computer, Inc. IR Receiver
    Thunderbolt Information: ℹ️
        Apple, Inc. MacBook Pro
    Kernel Extensions: ℹ️
            /Applications/Kies.app
        [not loaded]    com.devguru.driver.SamsungACMControl (1.4.28 - SDK 10.6) [Click for support]
        [not loaded]    com.devguru.driver.SamsungACMData (1.4.28 - SDK 10.6) [Click for support]
        [not loaded]    com.devguru.driver.SamsungComposite (1.4.28 - SDK 10.6) [Click for support]
        [not loaded]    com.devguru.driver.SamsungMTP (1.4.28 - SDK 10.5) [Click for support]
        [not loaded]    com.devguru.driver.SamsungSerial (1.4.28 - SDK 10.6) [Click for support]
            /System/Library/Extensions
        [not loaded]    com.IKMultimedia.driver.StompIO1 (1.0.0) [Click for support]
        [not loaded]    com.caiaq.driver.NIUSBGuitarRigMobileDriver (2.4.23) [Click for support]
        [not loaded]    com.caiaq.driver.NIUSBHardwareDriver (2.4.23) [Click for support]
        [loaded]    com.cleancutcode.displaypaddriver (9) [Click for support]
        [loaded]    com.cleancutcode.displaypadframebuffer (9) [Click for support]
        [not loaded]    com.ikmultimedia.driver.StealthPedal (1.0.0) [Click for support]
        [not loaded]    com.mice.driver.Wireless360Controller (1.0.0d12 - SDK 10.8) [Click for support]
        [not loaded]    com.mice.driver.WirelessGamingReceiver (1.0.0d12 - SDK 10.8) [Click for support]
        [not loaded]    com.mice.driver.Xbox360Controller (1.0.0d12 - SDK 10.8) [Click for support]
        [not loaded]    com.paceap.kext.pacesupport.master (5.9.1 - SDK 10.6) [Click for support]
        [loaded]    com.rim.driver.BlackBerryUSBDriverInt (0.0.97) [Click for support]
        [not loaded]    com.rim.driver.BlackBerryUSBDriverVSP (0.0.97) [Click for support]
        [loaded]    com.screenrecycler.driver.ScreenRecyclerDriver (1.4.13 - SDK 10.4) [Click for support]
        [not loaded]    jp.co.roland.RDUSB010FDev (1.0.0) [Click for support]
        [loaded]    tc.tctechnologies.driver.Saffire (4.0.0 13485 - SDK 10.0) [Click for support]
            /System/Library/Extensions/PACESupportFamily.kext/Contents/PlugIns
        [not loaded]    com.paceap.kext.pacesupport.leopard (5.9.1 - SDK 10.4) [Click for support]
        [not loaded]    com.paceap.kext.pacesupport.panther (5.9.1 - SDK 10.-1) [Click for support]
        [loaded]    com.paceap.kext.pacesupport.snowleopard (5.9.1 - SDK 10.6) [Click for support]
        [not loaded]    com.paceap.kext.pacesupport.tiger (5.9.1 - SDK 10.4) [Click for support]
    Startup Items: ℹ️
        IKStealthPedalMIDI: Path: /Library/StartupItems/IKStealthPedalMIDI
        Startup items are obsolete in OS X Yosemite
    Launch Agents: ℹ️
        [loaded]    com.google.keystone.agent.plist [Click for support]
        [running]    com.rim.BBAlbumArtCacher.plist [Click for support]
        [running]    com.rim.BBLaunchAgent.plist [Click for support]
    Launch Daemons: ℹ️
        [loaded]    com.adobe.fpsaud.plist [Click for support]
        [loaded]    com.google.keystone.daemon.plist [Click for support]
        [running]    com.mice.360Daemon.plist [Click for support]
        [loaded]    com.microsoft.office.licensing.helper.plist [Click for support]
        [running]    com.paceap.eden.licensed.plist [Click for support]
        [running]    com.rim.BBDaemon.plist [Click for support]
        [loaded]    PACESupport.plist [Click for support]
        [loaded]    tc.tctechnologies.Saffire.plist [Click for support]
    User Launch Agents: ℹ️
        [loaded]    com.google.GoogleContactSyncAgent.plist [Click for support]
        [loaded]    com.valvesoftware.steamclean.plist [Click for support]
    User Login Items: ℹ️
        NIHardwareAgent    Application  (/Library/Application Support/Native Instruments/Hardware/NIHardwareAgent.app)
        Console 1 On-Screen Display    Application  (/Applications/Console 1 On-Screen Display.app)
        KiesAgent    Application Hidden (/Applications/Kies.app/Contents/MacOS/KiesAgent.app)
        fuspredownloader    Application Hidden (/Users/[redacted]/Library/Application Support/.FUS/fuspredownloader.app)
    Internet Plug-ins: ℹ️
        Flip4Mac WMV Plugin: Version: 3.1.0.24   - SDK 10.8 [Click for support]
        FlashPlayer-10.6: Version: 16.0.0.305 - SDK 10.6 [Click for support]
        JavaAppletPlugin: Version: 14.9.0 - SDK 10.7 Check version
        Flash Player: Version: 16.0.0.305 - SDK 10.6 [Click for support]
        QuickTime Plugin: Version: 7.7.1
        o1dbrowserplugin: Version: 5.40.2.0 - SDK 10.8 [Click for support]
        SharePointBrowserPlugin: Version: 14.0.0 [Click for support]
        googletalkbrowserplugin: Version: 5.40.2.0 - SDK 10.8 [Click for support]
        JavaPlugin2_NPAPI: Version: 14.9.0 - SDK 10.7
        iPhotoPhotocast: Version: 7.0
    Safari Extensions: ℹ️
        Searchme [Adware! - Remove]
    3rd Party Preference Panes: ℹ️
        Flash Player  [Click for support]
        Flip4Mac WMV  [Click for support]
        Native Instruments USB Audio  [Click for support]
    Time Machine: ℹ️
        Time Machine not configured!
    Top Processes by CPU: ℹ️
             1%    WebProcess
             1%    fontd
             0%    BBLaunchAgent
             0%    WindowServer
             0%    Safari
    Top Processes by Memory: ℹ️
        314 MB    WebProcess
        219 MB    Safari
        60 MB    mds
        52 MB    WindowServer
        43 MB    Dock
    Virtual Memory Information: ℹ️
        1.65 GB    Free RAM
        1.32 GB    Active RAM
        429 MB    Inactive RAM
        894 MB    Wired RAM
        436 MB    Page-ins
        0 B    Page-outs
    Diagnostics Information: ℹ️
        Mar 9, 2015, 08:52:21 AM    Self test - passed

    When you see a beachball cursor or the slowness is especially bad, note the exact time: hour, minute, second.  
    These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
    Launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad and start typing the name.
    The title of the Console window should be All Messages. If it isn't, select
              SYSTEM LOG QUERIES ▹ All Messages
    from the log list on the left. If you don't see that list, select
              View ▹ Show Log List
    from the menu bar at the top of the screen.
    Each message in the log begins with the date and time when it was entered. Scroll back to the time you noted above.
    Select the messages entered from then until the end of the episode, or until they start to repeat, whichever comes first.
    Copy the messages to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
    The log contains a vast amount of information, almost all of it useless for solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
    Please don't indiscriminately dump thousands of lines from the log into this discussion.
    Please don't post screenshots of log messages—post the text.
    Some private information, such as your name, may appear in the log. Anonymize before posting.

  • T42 - Vista upgrade - very slow laptop - help please

    Hi
    I have installed Vista Home Premium on my T42 (previously had XP Pro) and it is now very, very slow.  Also it seems to have erased everything IBM - ie -Access IBM button not working.
    Type 2373 - f1G, HD 40mb, Memory 500kb.
    Do I need to increase hard disk? or memory? or both?
    If I choose to reinstall XP Pro, how do I go about it? I do not have the original XP Pro disk and assume it must have been preloaded.
    Sorry for the number of questions but I seem to have got myself into a situation over which my expertise is sadly lacking.  Beginning to wish I left well alone.
    Any help much appreciated.
    Thanks
    Maureen

    Welcome to the forum!
    There are several issues at work here:
    a) RAM. You need at least (which is the maximum for your machine, BTW) 2GB for Vista to run properly.
    b) Larger/newer/faster hard disk would also help.
    c) Please be advised that your GPU is NOT supported by Vista and that you'll have to look for modded drivers on the web, and even with them your scores won't be good.
    In my opinion, XP is the way to go for your machine. You can call Lenovo and order a set of recovery disks for a nominal fee.
    Should you choose to stay with Vista, go to "support and downloads" page on Lenovo's website, put in your model number and start updating and unpacking the drivers...
    Hope this helps.
    Cheers,
    George
    In daily use: R60F, R500F, T61, T410
    Collecting dust: T60
    Enjoying retirement: A31p, T42p,
    Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
    Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

  • SQL in statement very slow any help please

    Hi guys forgive me if i dont give enough information we dont normally have many problems with slow queries as our data does not usually get to a level that is effected by speed.
    I have a query that does a search of a view with approx 30k records. I then use a connect by to find all the relevent records that apply to this scenerio and place the results into an oracle form.
    I have hard coded an example ('ACT' and 6089) into this code, but usually the numbers/code will be a parameter thats passed in.
    Individually the select itemcode,notes from v_allitems takes approx 0.1 seconds to run
    and the IN statement takes approx 0.007 seconds to run.
    Together they take over 6 seconds which is a little too slow. So i assume its the IN thats causing me the problem as i am returning over 100 records to search IN. Is there an alternate way other than IN that anyone can think of to achieve the desired result?
    Thanks in advance
    select ITEMCODE, notes from v_allitems
    where ITEMCODE = ( 'ACT'||','||6089) OR ITEMCODE IN
        (SELECT pcchildcode
          ||','
          || pcchild item
           FROM afpc
          CONNECT BY pcparent = prior pcchild
        AND pcparentcode        = prior pcchildcode START
        WITH pcparent           = 6089
        AND pcparentcode        = 'ACT'
      UNION ALL
         SELECT pcparentcode
          ||','
          || pcparent item
           FROM afpc
          CONNECT BY pcchild = prior pcparent
        AND pcchildcode        = prior pcparentcode START
        WITH pcchild           = 6089
        AND pcchildcode        = 'ACT'
        )

    I have just found another thread talking about the EXISTS condition, ill look into whether this will speed it up

  • Mavericks install incomplete. No Apple installers on HD. Will I be able to upgrade to Yosemite and will it fix all that didn't install with Mavericks upgrade? Very slow connection speeds 30 hrs to download Mavericks. Tried re-install; no help/

    Ever since upgrade to Mavericks I have been having problems which are too numerous to mention. I finally found a program from a UCBerkley professor called Pacifier which indicated 4000+ of 400,000+ files and folders did not install. I was unable to go further to try to fix everything because Pacifier can't find ANY Apple installers on my HD. It recommended I download the Mavericks installer without reinstalling to continue; however, after having done so (very slow connection; takes 30 hours to download) and although the installer appears in apps while downloading it disappears and NO Apple installer packages can be found on my hard drive. I tried to download Yosemite once and it indicated my system wasn't eligible for the upgrade. Its' download time was similar to Mavericks; 28+ hours.
    I am using a Macbook Pro mid-2012 version OS X 10.9.5 (13F34); Processor 2.5 GHz Intel Core i5; Memory  4 GB 1600 MHz DDR3; Graphics  Intel HD Graphics 4000 1024 MB.
    Regardless of how many files and apps I remove my memory is being eaten up to the point I can hardly do anything at all. There are no civil words for how frustrated I am. Someone please help me.
    Thanks,
    JJ

    Install Mavericks, Lion/Mountain Lion Using Internet Recovery
    Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
    Boot to the Internet Recovery HD:
    Restart the computer and after the chime press and hold down the COMMAND-OPTION- R keys until a globe appears on the screen. Wait patiently - 15-20 minutes - until the Recovery main menu appears.
    Partition and Format the hard drive:
    Select Disk Utility from the main menu and click on the Continue button.
    After DU loads select your newly installed hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
    Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed. Quit DU and return to the main menu.
    Reinstall Lion/Mountain Lion. Mavericks: Select Reinstall Lion/Mountain Lion, Mavericks and click on the Install button. Be sure to select the correct drive to use if you have more than one.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
    This should restore the version of OS X originally pre-installed on the computer.

  • Help : very slow connection speed with AEBS and iMac

    I connect to the internet using my newly purchased AEBS. I have a MacBook and an 24" iMac ( purchased in Nov 2007). My iMac showed very slow connecting speed of <1 MB/s download; with my MacBook placed just 1 foot from my iMac, the MacBook showed an amazing download speed of 20MB/s. If i connect the iMac to the AEBS using ethernet cable, it can get a very high speed.
    So, where is the problem??
    I am new to wireless, please help. I use iMac more than my MacBook at home.
    Actually, i did not touch the any of the advance setting of the AEBS.

    You know, I am experiencing the same problem. My wife's PC and iPhone are blazing fast, but my MacBook is accessing the internet at about dial-up speeds. Very frustrating and I haven't yet found the culprit.
    Anyone???

  • Since up dating my Firefox I can not play any games on Facebook they all run very slow, can someone please help me with a solution.

    Since up dating my Firefox I can not play any games on Facebook they all run very slow, can someone please help me with a solution.It mainly seems to be with games.

    RE: "P.S. I  found it aggravating that I couldn't copy and paste text  here, it wanted me to insert as a link or an image, how do you insert plain  text?"
    I take it you tried using the "right click" menu?   That doesn't seem to work, as you noted, but, you should be able to paste text by pressing your CTRL key  and while holding it down, press the "V" letter  key.
    CTRL + C = COPY
    CTRL + X = CUT
    CTRL + V = PASTE
    HTH,
    Ortho_Fan

  • Very slow connection with Mifi 4510L??

    I'm hoping someone here can give some guidance. I am having very slow connection with the 4510L we just got. Via test on speedtest.net I'm seeing download speed of .17 MBPS at times it was so slow the test was not completing. I normally have 1 or 2 bars on the mifi unit and have seen up to 3 at times. I drove into town and see the same range (1 to 3 bars). I have yet to see the 4G light come on except for prior to activation (would light solid green at times) since activating I have only seen the violet light for 3G.
    Verizon advertises full service both around our city (Richmond, VA) and at my more remote location in Hanover. I have been through the recommended resets and nothing seems to improve the connection speed. Could the unit itself be defective? Also, I've noticed when I go to a location website it thinks I am in Pennsylvania when I am in Virginia. Could the Mifi be trying to connect to a signal in that location for some reason (was refurbished device)
    Thanks for any help you can offer,
    Brian

    I was having problems but upgrading to 2.28 seems to have helped me in addition to a few other changes I made based on this review of the 4510L
    http://www.anandtech.com/show/4500/novatel-wireless-mifi-4510l-review-the-best-4g-lte-wifi-hotspot/4
    1) "selecting WPA2 Personal/PSK (AES)"
    2) "manually selecting a channel (instead of Auto) fixes almost all the instability problems"
    (I'm not sure if it actually worked as the diagnostics always shows channel 0 no matter what I picked.  I did try a couple before one - or the myriad of other things I tried - seemed to make a difference - at least for now - fingers crossed)
    3) "allowing for one to select between each network mode manually, so you can force 4G LTE, EVDO, 1xRTT, or all of the above. This is incredibly useful if you’re right at the cutoff for 4G LTE SINR"  (that's WWAN Preferred Mode LTE only for me)
    4) I also changed my 802.11 Mode to just one mode that works on both computers at my house
    5) I am also careful to turn it off when I am done with it and take it off the charger for the night as well.
    It is my only internet service due to my semiremote location (no cable etc) and when I first got it as a replacement for my dependable 2200 I was about to pull all my hair out.  I was "forced" into it because due to antenna issues on a local tower that supplies my 3G signal my 2200 wasn't even able to load my gmail account.  Verizon very helpful on that - call us if its still an issue in a "few weeks"!  However, when I inquired about the antenna's effect on a 4G signal, an intelligent tech was able to tell me that it was not the tower I would be getting a 4G signal off of - odd but I didn't question that possibility.
    It runs very very warm but I suspect having it on the charger and using it almost all day is part of that.  At first I was wondering if heat was part of the problem - going so far as to have it sitting on an ice pack to test that theory.  Of course then I had to wonder if maybe I was freezing it -lol.  I am careful to turn it off when I am done with it and take it off the charger for the night as well.
    I've been on it most of the day and it seems to be behaving well - so fingers crossed

  • Very slow connection after phone line repair

    I had my phone line repaired yesterday with new cabling and new BT box for phone and computer.My phone is fine, but the hub for my broadband does not appear to be ok.  the phone symbol on the hub did not light up at all  this morning, and after restarting the hub and going back to default settings it is now glowing orange only.  It was ok yesterday after being fixed. Very slow connection now. Should i keep  everything on  to see if it will right itself, or re-start yet again?
    I have been looking on BT's options for fixing but can't seem to find anything. the connections in my area are fine so it can't be an outside fault

    Which home hub do you have? Did you recently re-contract or change your package, as that will affect your hub phone.
    As for the speed issue, it should get better if you leave it alone.
    See Why has my speed dropped
    There are some useful help pages here, for BT Broadband customers only, on my personal website.
    BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

  • ARD 3.7.2 very slow connection on Lan

    I'm running ARD 3.7.2 on MacBook Air (OSX 10.9.2) to connect mac mini (8gb / osx 10.9.2)  very slow connection on LAN.
    Mini connected to LAN 100Mbit Ethernet, MacBook connection is wi-fi

    Ok, I solved it after doing some extensive Google searching.  Still not sure why ARD went bonkers, but here's my fix.
    1. Download the ARD 3.7.1 client drom the Apple downloads page and install it manually on the client machine.
    2.  Go back to the administrator machine and delete the computer client from the computers list.
    3.  From the scanners list, find the now visible client machine (it will probably say "no user name or password" next to it) and drag it to the computer list.
    4.  When you drag it over it will ask for the username and password.  Fill in an administrator user name and password for that computer, click OK and you're done.
    Still a mystery as to why ARD software itself will not create new client packages.  I still haven't figured that part out.  Downloading the standard client package from Apple is the only work around I know of so far.  Good luck.

  • Tweak Firefox to very slow connection

    Como configurar(no about:config) o meu firefox para conexões muito lentas?
    Algo em torno de 32KBps?
    Máximo de conexões? Pipeling? Requisições máximas, etc...
    Obrigado desde já.
    How to tweak(in about:config) Firefox to very slow connection?
    Like 32KBps.
    maxrequests? Pipeling(true or false)? MaxConn?
    Thanks!

    Olá sistematico,
    Postei uma resposta [https://support.mozilla.org/pt-BR/questions/960088 neste outro tópico].
    Aguardamos sua resposta nele, para que possamos lhe ajudar. =)
    Abraços,
    - Ralph

  • Very SLOW connection - 5 mbps download

    Since November, 2014, I've been experiencing very slow connection.
    Redlands, CA 92373
    5 mbps download 30 mbps upload
    Called the call center 5 times. Each time, just a bunch of rebooting the router & speedtest.net checking
    A new Verizon router was installed and didn't improve anything.
    Technician 1 visited and mentioned that there is a network hardware problem in the area and many people called in for slow connection issues. The technician rebooted the ONT box and said if the speed goes down again, the ONT box should be replaced. The speed went down as soon as the technical left.
    Technician 2 visited and replaced the ONT box. Later that day, the speed went down to 5 mpbs for download.
    It's so slow at the time of writing this that Facebook page is rendered with texts only.
    Are there anyone from Redlands, CA area who have been experiencing the slow connection for a while?
    I don't want to call in again to go thru another around of 1 hour long rebooting / resetting the router and chekcing the speedtest.net exercises.
    I feel I am being ripped off because I am paying for 75/75.
    I'm running out of patience and am considering to switch to Timewarner.

    Oh Man this things popping out of everywhere!!!!!!!
    1.Router: Quantum G1100 (Primary)2.Router :Nighthawk AC1900
    3.Speed:75/75 Mbps
    4.FIOS TV Ultimate HD
    5.FiOS Digital Voice Unlimited

  • MacBookAir is frozen.  Won't turn off.  Getting VERY warm.  Help, please!

    MacBookAir is frozen.  Won't turn off.  Getting VERY warm.  Help, please!

    Hi Katharine,
    Hold down the power button until the screen turns black.
    Then wait about a minute then press the power button once to turn it back on.
    If you can't shut it down, if you're in the Walnut Creek I think you are, there's an Apple Store on South Main Street.
    You can make a reservation at their Genius Bar in advance >  Apple Retail Store - Genius Bar

  • Very very slow broadband , someone please help

    Hi have come here as a last resort , i have been a bt internet/broadband user for over 10 years have had broadband for a long time , we often in our house have me playing games online on the pc , the kids have the xbox 360 and the mrs will have the ipad all hooked up at the same time with no problems ,
    then friday the broadband dropped and we had a orange flashing light ,
    it came back on about 5 mins later and ever since it is very very slow , i have tryed resteing and rebooting the router , it connects to the internet just fine but everything is running ar a snails pace , tryed calling them which is a nightmare trying to explaine to a call center guy , they told me to hang up for a line test and they would call me back and havnt bothered
    i have done the line test online it it comes back as ok , we have noticed some nose on the phone line from today
    can anyone please give me some advice?
    here is btspeed check results:
    FAQ
    <script type="text/javascript"></script> Test1 comprises of Best Effort Test: -provides background information.
    Download  Speed
    80 Kbps
    0 Kbps
    250 Kbps
    Max Achievable Speed
     Download speedachieved during the test was - 80 Kbps
     For your connection, the acceptable range of speeds is 50-250 Kbps.
     Additional Information:
     Your DSL Connection Rate :160 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
     IP Profile for your line is - 135 Kbps
    If you wish to discuss these results please contact your ISP.
    If you are experiencing problems with specific applications, servers or websites please contact your ISP for assistance.
    Your test has completed please close this window to exit the performance tester.
    Please visit FAQ section if you are unable To understand the test results.
    http://speedtest.net/result/1379380863.png

    have phoned them 4 times now (2 times on 151) and they ensure me they have tested the line and i have no fault , they set up remote asstent and the guy did a soft restart of my hub which seemed to work , he then tryed to get me a better d/l speed but it whet back to a poor one again , so he again did a soft restart and i now get this:
    ADSL line status
    Connection Information
    Line state
    Connected <script type="text/javascript"></script>
    Connection time
    0 days, 00:40:50
    Downstream
    352 Kbps
    Upstream
    448 Kbps
    ADSL Settings
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    G.992.1 Annex A
    Latency type
    Interleaved
    Noise margin (Down/Up)
    11.4 dB / 21.0 dB
    Line attenuation (Down/Up)
    21.4 dB / 12.0 dB
    Output power (Down/Up)
    1.0 dBm / 1.5 dBm
    the downstream and upstream numbers are both better but it has made no differnace, every page i go to takes ages to load (if they load at all) and the ipad wont load at all , this is now getting silly i have wasted around 6 hrs of my time tonight trying to fix this and now just feel like canceling and ordering from eleswhere as i know the messing i will have to go through in the morning to explaine this from the start to a new call center worker all over again
    i was led to belive that bt staff would help me if i posted here hence why i did so but even this is looking like a total waste of my time , (no dissrepect to you imjolly for your help)

  • Time Machine Very Slow (321 Days) Please Help!

    Hi all, I've got a 2012 MBP and have had problems with TM since day one.
    I'm running all the latest software with a brand new Time Capsule and it states that it will take over 300 days to back up.
    I originally used a NAS and TM was very very slow along with having to reformat and start again every few weeks so I gave in and got a TC thinking it would solve my problems but it's returned again.
    I've tried reformatting, disabling spotlight, wired and wireless connections, different hard drives and still the problem persists. Occasionally it also fails to find the backup disk so I have to reformat and start again.
    It's driving me absolutely insane because despite messing and messing, trying different solutions the problem always seems to return at random. It will work great for a week or 2 then it's back to square one.
    Can someone please restore my sanity and help?

    To update, I got up this morning and it was still stating some 22 days after copying a few gb in 18 hours so I restarted (again). TM then stated it couldn't find the back up disk so I again pointed it to the right disk and it now appears to be stuck again after doing over a gb in a minute or two.
    Here's the info requested.
    31/01/2013 09:53:34.380 com.apple.backupd[398]: Starting manual backup
    31/01/2013 09:53:46.000 kernel[0]: nfs server localhost:/jiWSkBZ-Y-Uq-EgHJVYVPN: not responding
    31/01/2013 09:53:47.000 kernel[0]: nfs server localhost:/jiWSkBZ-Y-Uq-EgHJVYVPN: can not connect, error 61
    31/01/2013 09:54:16.262 KernelEventAgent[46]: tid 00000000 received event(s) VQ_DEAD (32)
    31/01/2013 09:54:16.263 KernelEventAgent[46]: tid 00000000 type 'mtmfs', mounted on '/Volumes/MobileBackups', from 'localhost:/jiWSkBZ-Y-Uq-EgHJVYVPN', dead
    31/01/2013 09:54:16.000 kernel[0]: nfs server localhost:/jiWSkBZ-Y-Uq-EgHJVYVPN: dead
    31/01/2013 09:54:16.263 KernelEventAgent[46]: tid 00000000 force unmount localhost:/jiWSkBZ-Y-Uq-EgHJVYVPN from /Volumes/MobileBackups
    31/01/2013 09:54:16.263 KernelEventAgent[46]: tid 00000000 found 1 filesystem(s) with problem(s)
    31/01/2013 09:54:22.198 com.apple.backupd[398]: Failed to get NSURLVolumeURLForRemountingKey for /Volumes/MobileBackups, error: Error Domain=NSCocoaErrorDomain Code=4 "The file “MobileBackups” doesn’t exist." UserInfo=0x7f9934a04da0 {NSURL=file://localhost/Volumes/MobileBackups/, NSFilePath=/Volumes/MobileBackups}
    31/01/2013 09:54:22.198 com.apple.backupd[398]: Attempting to mount network destination URL: afp://Dave%[email protected]/AirPort%20Disk
    31/01/2013 09:54:23.036 com.apple.backupd[398]: Mounted network destination at mount point: /Volumes/AirPort Disk using URL: afp://Dave%[email protected]/AirPort%20Disk
    31/01/2013 09:54:23.000 kernel[0]: ASP_TCP asp_tcp_usr_control: invalid kernelUseCount 0
    31/01/2013 09:54:23.000 kernel[0]: AFP_VFS afpfs_mount: /Volumes/AirPort Disk, pid 435
    31/01/2013 09:54:23.000 kernel[0]: AFP_VFS afpfs_mount : succeeded on volume 0xffffff80946e1008 /Volumes/AirPort Disk (error = 0, retval = 0)
    31/01/2013 09:54:48.061 mdworker[434]: Unable to talk to lsboxd
    31/01/2013 09:54:48.000 kernel[0]: Sandbox: sandboxd(442) deny mach-lookup com.apple.coresymbolicationd
    31/01/2013 09:54:51.281 sandboxd[442]: ([434]) mdworker(434) deny mach-lookup com.apple.ls.boxd
    31/01/2013 09:54:51.000 kernel[0]: nspace-handler-set-snapshot-time: 1359626093
    31/01/2013 09:55:28.923 mds[40]: (Error) Volume: Root store set to FSOnly with matching create! (loaded:1)
    31/01/2013 09:55:29.892 com.apple.backupd[398]: Disk image /Volumes/AirPort Disk/Dave’s MacBook Pro.sparsebundle mounted at: /Volumes/Time Machine Backups
    31/01/2013 09:55:29.937 com.apple.backupd[398]: Backing up to: /Volumes/Time Machine Backups/Backups.backupdb
    31/01/2013 09:55:30.908 com.apple.backupd[398]: Forcing deep traversal on source: "Macintosh HD" (mount: '/' fsUUID: 74A87C50-39EA-3B75-AACA-0647768C78F6 eventDBUUID: 539B3BBD-544C-444D-9C2C-14001A19F631)
    31/01/2013 09:55:32.032 com.apple.backupd[398]: Didn't get valid migration dates.
    31/01/2013 09:55:32.040 com.apple.backupd[398]: Found 806587 files (286.4 GB) needing backup
    31/01/2013 09:55:32.041 com.apple.backupd[398]: 343.68 GB required (including padding), 1.99 TB available
    31/01/2013 09:56:15.000 kernel[0]: (default pager): [KERNEL]: ps_allocate_cluster - send HI_WAT_ALERT
    31/01/2013 09:56:15.000 kernel[0]: macx_swapon SUCCESS
    31/01/2013 09:56:43.954 com.apple.usbmuxd[27]: _handle_timer heartbeat detected detach for device 0x1b-192.168.0.13:0!
    31/01/2013 09:56:51.626 mdworker[488]: Unable to talk to lsboxd
    31/01/2013 09:56:51.746 sandboxd[489]: ([488]) mdworker(488) deny mach-lookup com.apple.ls.boxd
    31/01/2013 09:56:52.000 kernel[0]: Sandbox: sandboxd(489) deny mach-lookup com.apple.coresymbolicationd
    31/01/2013 09:57:06.212 CVMServer[83]: Check-in to the service com.apple.cvmsCompAgent_x86_64 failed. This is likely because you have either unloaded the job or the MachService has the ResetAtClose attribute specified in the launchd.plist. If present, this attribute should be removed.
    31/01/2013 09:57:06.406 launchctl[493]: launchctl: Dubious ownership on file (skipping): /Library/LaunchAgents/com.davdaerve.UpdatePodcastsAgent.plist
    31/01/2013 09:57:07.174 CVMServer[83]: Check-in to the service com.apple.cvmsCompAgent_x86_64 failed. This is likely because you have either unloaded the job or the MachService has the ResetAtClose attribute specified in the launchd.plist. If present, this attribute should be removed.
    31/01/2013 09:57:14.580 Folder Sync[495]: Growl.framework loaded
    31/01/2013 09:57:14.645 Folder Sync[495]: Using existing log dir: /Users/davedaerve/Library/com.destek.foldersync
    31/01/2013 09:57:20.128 Folder Sync[495]: Scheduler: Run Check for 9:57
    31/01/2013 09:57:26.027 mDNSResponder[41]: ERROR: handle_resolve_request bad interfaceIndex 1
    31/01/2013 09:57:26.129 mDNSResponder[41]: ERROR: handle_resolve_request bad interfaceIndex 15
    31/01/2013 09:57:26.258 mDNSResponderHelper[497]: do_mDNSSendWakeupPacket write failed Device not configured
    31/01/2013 09:57:26.259 mDNSResponderHelper[497]: do_mDNSSendWakeupPacket write failed Device not configured
    31/01/2013 09:57:26.261 mDNSResponder[41]: ERROR: handle_resolve_request bad interfaceIndex 16
    31/01/2013 09:57:26.285 mDNSResponder[41]: ERROR: handle_resolve_request bad interfaceIndex 24
    31/01/2013 09:57:27.132 mDNSResponderHelper[497]: do_mDNSSendWakeupPacket write failed Device not configured
    31/01/2013 09:57:37.838 iTunes[496]:  AVF KeyExchange Version from driver for Certificates 1
    31/01/2013 09:57:46.991 Twitter[498]: font ChicagoBold loaded
    31/01/2013 09:57:47.054 Twitter[498]: font pixChicago loaded
    31/01/2013 09:57:48.244 Twitter[498]: could not fetch oAuthTokenSecret, this account will get removed
    31/01/2013 09:57:51.623 Mail[499]: Using V2 Layout
    31/01/2013 09:57:52.921 com.apple.SecurityServer[16]: Session 100012 created
    31/01/2013 09:57:56.499 com.apple.launchd[1]: (com.apple.qtkitserver[258]) Exited: Killed: 9
    31/01/2013 09:57:56.000 kernel[0]: memorystatus_thread: idle exiting pid 258 [com.apple.qtkits]
    31/01/2013 09:57:57.000 kernel[0]: memorystatus_thread: idle exiting pid 242 [cfprefsd]
    31/01/2013 09:57:58.338 librariand[500]: MMe quota status changed: under quota
    31/01/2013 09:57:58.350 com.apple.usbmuxd[27]: _handle_timer heartbeat detected detach for device 0x1c-192.168.0.6:0!
    31/01/2013 09:57:58.998 com.apple.usbmuxd[27]: _handle_timer heartbeat detected detach for device 0x1d-192.168.0.5:0!
    31/01/2013 09:57:59.088 Mail[499]: *** -[IADomainCache init]: IA domains cache is out of date.
    31/01/2013 09:58:00.137 Folder Sync[495]: Scheduler: Run Check for 9:58
    31/01/2013 09:58:00.147 com.apple.launchd.peruser.501[141]: ([0x0-0x14014].com.apple.inputmethod.ironwood[223]) Exited: Killed: 9
    31/01/2013 09:58:00.000 kernel[0]: memorystatus_thread: idle exiting pid 223 [DictationIM]
    31/01/2013 09:58:19.718 Mail[499]: Couldn't contact spell checker for Multilingual
    31/01/2013 09:58:48.777 com.apple.launchd[1]: (com.apple.iCloudHelper[232]) Exited: Killed: 9
    31/01/2013 09:58:48.000 kernel[0]: memorystatus_thread: idle exiting pid 232 [com.apple.iCloud]
    31/01/2013 09:58:49.895 com.apple.launchd.peruser.501[141]: (com.apple.tccd[213]) Exited: Killed: 9
    31/01/2013 09:58:49.000 kernel[0]: memorystatus_thread: idle exiting pid 213 [tccd]
    31/01/2013 09:58:49.937 WindowServer[106]: CGXRegisterWindowWithSystemStatusBar: window b already registered
    31/01/2013 09:58:50.000 kernel[0]: memorystatus_thread: idle exiting pid 211 [xpcd]
    31/01/2013 09:58:50.453 com.apple.launchd[1]: (com.apple.xpcd.F5010000-0000-0000-0000-000000000000[211]) Exited: Killed: 9
    31/01/2013 09:58:54.351 com.apple.launchd.peruser.0[278]: (com.apple.distnoted.xpc.agent[300]) Exited: Killed: 9
    31/01/2013 09:58:54.000 kernel[0]: memorystatus_thread: idle exiting pid 300 [distnoted]
    31/01/2013 09:58:54.000 kernel[0]: memorystatus_thread: idle exiting pid 240 [distnoted]
    31/01/2013 09:58:54.920 com.apple.launchd.peruser.501[141]: (com.apple.accountsd[210]) Exited: Killed: 9
    31/01/2013 09:58:55.000 kernel[0]: memorystatus_thread: idle exiting pid 210 [accountsd]
    31/01/2013 09:58:55.559 com.apple.launchd.peruser.501[141]: (com.apple.CalendarAgent[187]) Exited: Killed: 9
    31/01/2013 09:58:55.000 kernel[0]: memorystatus_thread: idle exiting pid 187 [CalendarAgent]
    31/01/2013 09:58:58.000 kernel[0]: (default pager): [KERNEL]: ps_select_segment - send HI_WAT_ALERT
    31/01/2013 09:58:58.000 kernel[0]: macx_swapon SUCCESS
    31/01/2013 09:59:00.149 Folder Sync[495]: Scheduler: Run Check for 9:59
    31/01/2013 09:59:06.000 kernel[0]: (default pager): [KERNEL]: ps_select_segment - send HI_WAT_ALERT
    31/01/2013 09:59:06.000 kernel[0]: macx_swapon SUCCESS
    31/01/2013 09:59:08.759 launchctl[512]: launchctl: Dubious ownership on file (skipping): /Library/LaunchAgents/com.davdaerve.UpdatePodcastsAgent.plist
    31/01/2013 10:00:00.158 Folder Sync[495]: Scheduler: Run Check for 10:00
    31/01/2013 10:00:01.180 launchctl[525]: launchctl: Dubious ownership on file (skipping): /Library/LaunchAgents/com.davdaerve.UpdatePodcastsAgent.plist
    31/01/2013 10:00:09.000 kernel[0]: memorystatus_thread: idle exiting pid 515 [cfprefsd]
    31/01/2013 10:00:33.665 mdworker[639]: Unable to talk to lsboxd
    31/01/2013 10:00:34.000 kernel[0]: Sandbox: sandboxd(640) deny mach-lookup com.apple.coresymbolicationd
    31/01/2013 10:00:34.311 sandboxd[640]: ([639]) mdworker(639) deny mach-lookup com.apple.ls.boxd
    31/01/2013 10:01:00.171 Folder Sync[495]: Scheduler: Run Check for 10:01
    31/01/2013 10:01:10.060 Folder Sync[495]: objc[495]: Object 0x10bc05ab0 of class NSUserDefaults autoreleased with no pool in place - just leaking - break on objc_autoreleaseNoPool() to debug
    31/01/2013 10:01:14.200 com.apple.launchd.peruser.501[141]: (com.apple.tccd[647]) Exited: Killed: 9
    31/01/2013 10:01:14.000 kernel[0]: memorystatus_thread: idle exiting pid 647 [tccd]
    31/01/2013 10:01:31.206 lsboxd[228]: @AE relay 4755524c:4755524c
    31/01/2013 10:01:31.502 WindowServer[106]: CGXRegisterWindowWithSystemStatusBar: window b already registered
    31/01/2013 10:01:57.362 CalendarAgent[660]: *** -[IADomainCache init]: IA domains cache is out of date.
    31/01/2013 10:02:00.182 Folder Sync[495]: Scheduler: Run Check for 10:02
    31/01/2013 10:02:14.579 CalendarAgent[660]: [com.apple.calendar.store.log.caldav.queue] [Account refresh failed with error: Error Domain=CoreDAVHTTPStatusErrorDomain Code=503 "The operation couldn’t be completed. (CoreDAVHTTPStatusErrorDomain error 503.)" UserInfo=0x7fc9524481d0 {AccountName=Yahoo!, CalDAVErrFromRefresh=YES, CoreDAVHTTPHeaders=<CFBasicHash 0x7fc9520cc0c0 [0x10aa25fd0]>{type = immutable dict, count = 11,
    entries =>
              0 : Case Insensitive Key: Connection = <CFString 0x7fc9520b7470 [0x10aa25fd0]>{contents = "keep-alive"}
              1 : Case Insensitive Key: Content-Type = <CFString 0x7fc9520bc410 [0x10aa25fd0]>{contents = "text/html; charset=UTF-8"}
              2 : Case Insensitive Key: Retry-After = <CFString 0x7fc952086140 [0x10aa25fd0]>{contents = "3600"}
              3 : Case Insensitive Key: Via = <CFString 0x7fc9520cb850 [0x10aa25fd0]>{contents = "HTTP/1.1 calgate003.cal.ac4.yahoo.com (YahooTrafficServer/1.19.11 [c s f ])"}
              4 : Case Insensitive Key: Age = <CFString 0x10a9fa110 [0x10aa25fd0]>{contents = "0"}
              5 : Case Insensitive Key: P3P = <CFString 0x7fc952086050 [0x10aa25fd0]>{contents = "policyref="http://info.yahoo.com/w3c/p3p.xml", CP="CAO DSP COR CUR ADM DEV TAI PSA PSD IVAi IVDi CONi TELo OTPi OUR DELi SAMi OTRi UNRi PUBi IND PHY ONL UNI PUR FIN COM NAV INT DEM CNT STA POL HEA PRE LOC GOV""}
              6 : Case Insensitive Key: Date = <CFString 0x7fc95209e440 [0x10aa25fd0]>{contents = "Thu, 31 Jan 2013 10:02:14 GMT"}
              7 : Case Insensitive Key: Server = <CFString 0x7fc9520b7490 [0x10aa25fd0]>{contents = "YTS/1.19.11"}
              8 : Case Insensitive Key: Transfer-Encoding = <CFString 0x10bf826f8 [0x10aa25fd0]>{contents = "Identity"}
              11 : Case Insensitive Key: Cache-Control = <CFString 0x7fc9520cff40 [0x10aa25fd0]>{contents = "private"}
              12 : Case Insensitive Key: Vary = <CFString 0x7fc9520b67f0 [0x10aa25fd0]>{contents = "Accept-Encoding"}
    31/01/2013 10:03:00.193 Folder Sync[495]: Scheduler: Run Check for 10:03
    31/01/2013 10:03:23.921 iTunes[496]: _NotificationSocketReadCallbackGCD (thread 0x10717e180): Unexpected connection closure...
    31/01/2013 10:03:23.923 ath[665]: _NotificationSocketReadCallbackGCD (thread 0x101b21180): Unexpected connection closure...
    31/01/2013 10:03:25.439 mds[40]: (Warning) FMW: event:1 had an arg mismatch.  ac:2 am:51
    31/01/2013 10:03:29.551 com.apple.launchd.peruser.501[141]: (com.apple.CalendarAgent[660]) Exited: Killed: 9
    31/01/2013 10:03:29.000 kernel[0]: memorystatus_thread: idle exiting pid 660 [CalendarAgent]
    31/01/2013 10:03:45.425 iTunes[496]: _NotificationSocketReadCallbackGCD (thread 0x10717e180): Unexpected connection closure...
    31/01/2013 10:03:45.427 ath[665]: _NotificationSocketReadCallbackGCD (thread 0x101b21180): Unexpected connection closure...
    31/01/2013 10:04:00.203 Folder Sync[495]: Scheduler: Run Check for 10:04
    31/01/2013 10:04:13.627 CalendarAgent[673]: *** -[IADomainCache init]: IA domains cache is out of date.
    31/01/2013 10:04:16.750 Twitter[498]: will terminate
    31/01/2013 10:04:16.789 Twitter[498]: Error: no oAuthTokenSecret set for account
    31/01/2013 10:04:23.078 CalendarAgent[673]: [com.apple.calendar.store.log.caldav.queue] [Account refresh failed with error: Error Domain=CoreDAVHTTPStatusErrorDomain Code=401 "The operation couldn’t be completed. (CoreDAVHTTPStatusErrorDomain error 401.)" UserInfo=0x7fca11285a50 {AccountName=Yahoo!, CalDAVErrFromRefresh=YES, CoreDAVHTTPHeaders=<CFBasicHash 0x7fca1160a910 [0x10f5b6fd0]>{type = immutable dict, count = 11,
    entries =>
              0 : Case Insensitive Key: Connection = <CFString 0x7fca13581410 [0x10f5b6fd0]>{contents = "keep-alive"}
              1 : Case Insensitive Key: Content-Type = <CFString 0x7fca11607420 [0x10f5b6fd0]>{contents = "text/html; charset=UTF-8"}
              2 : Case Insensitive Key: Server = <CFString 0x7fca11607450 [0x10f5b6fd0]>{contents = "YTS/1.19.11"}
              3 : Case Insensitive Key: Via = <CFString 0x7fca1160a8b0 [0x10f5b6fd0]>{contents = "HTTP/1.1 calgate007.cal.ac4.yahoo.com (YahooTrafficServer/1.19.11 [c s f ])"}
              4 : Case Insensitive Key: Age = <CFString 0x10f58b110 [0x10f5b6fd0]>{contents = "0"}
              5 : Case Insensitive Key: P3P = <CFString 0x7fca11610b00 [0x10f5b6fd0]>{contents = "policyref="http://info.yahoo.com/w3c/p3p.xml", CP="CAO DSP COR CUR ADM DEV TAI PSA PSD IVAi IVDi CONi TELo OTPi OUR DELi SAMi OTRi UNRi PUBi IND PHY ONL UNI PUR FIN COM NAV INT DEM CNT STA POL HEA PRE LOC GOV""}
              6 : Case Insensitive Key: Date = <CFString 0x7fca135f2890 [0x10f5b6fd0]>{contents = "Thu, 31 Jan 2013 10:04:22 GMT"}
              7 : Case Insensitive Key: Transfer-Encoding = <CFString 0x110b206f8 [0x10f5b6fd0]>{contents = "Identity"}
              9 : Case Insensitive Key: Www-Authenticate = <CFString 0x7fca135f28c0 [0x10f5b6fd0]>{contents = "Basic realm="Zimbra""}
              11 : Case Insensitive Key: Cache-Control = <CFString 0x7fca116d2810 [0x10f5b6fd0]>{contents = "private"}
              12 : Case Insensitive Key: Vary = <CFString 0x7fca135f28f0 [0x10f5b6fd0]>{contents = "Accept-Encoding"}
    31/01/2013 10:04:27.512 iTunes[496]: _NotificationSocketReadCallbackGCD (thread 0x10717e180): Unexpected connection closure...
    31/01/2013 10:04:27.514 ath[665]: _NotificationSocketReadCallbackGCD (thread 0x101b21180): Unexpected connection closure...
    31/01/2013 10:04:27.851 Dock[156]: trying to take pid 499 out of fullscreen but it is not the current space
    31/01/2013 10:04:27.972 Mail[499]: CGSGetWindowTags: Invalid window 0x0
    31/01/2013 10:04:27.972 Mail[499]: void _NSMoveWindowToSpaceUnlessSticky(NSInteger, CGSSpaceID): CGSGetWindowTags(cid, win, tags, kCGSRealMaximumTagSize) returned CGError 1000 on line 1247
    31/01/2013 10:04:27.977 WindowServer[106]: CGXSetWindowListTags: Invalid window 0
    31/01/2013 10:04:33.945 iTunes[496]: 2013-01-31 10:04:33.944722 AM [AVSystemController] Stopping AirPlay
    31/01/2013 10:04:34.218 WindowServer[106]: CGXGetConnectionProperty: Invalid connection 82119
    31/01/2013 10:04:34.218 WindowServer[106]: CGXGetConnectionProperty: Invalid connection 82119
    31/01/2013 10:04:34.219 WindowServer[106]: CGXGetConnectionProperty: Invalid connection 82119
    31/01/2013 10:05:07.671 mdworker[671]: Unable to talk to lsboxd
    31/01/2013 10:05:08.000 kernel[0]: Sandbox: sandboxd(680) deny mach-lookup com.apple.coresymbolicationd
    31/01/2013 10:05:08.457 sandboxd[680]: ([671]) mdworker(671) deny mach-lookup com.apple.ls.boxd
    31/01/2013 10:05:21.289 com.apple.SecurityServer[16]: Killing auth hosts
    31/01/2013 10:05:21.289 com.apple.SecurityServer[16]: Session 100012 destroyed
    31/01/2013 10:09:59.228 WindowServer[106]: CGXRegisterWindowWithSystemStatusBar: window b already registered
    31/01/2013 10:10:15.787 mdworker[697]: Unable to talk to lsboxd
    31/01/2013 10:10:16.000 kernel[0]: Sandbox: sandboxd(810) deny mach-lookup com.apple.coresymbolicationd
    31/01/2013 10:10:16.708 sandboxd[810]: ([697]) mdworker(697) deny mach-lookup com.apple.ls.boxd

  • VERY SLOW RAID0 speeds, please help!

    file:///Users/new/Desktop/screenie.png
    please see attachment -- getting very slow read write speeds on raid0 strip set. how to fix?
    used various benchmarks including xbench, blackmagic disk speed test & trim enabler.
    i cant upload pipctures for some reason, regardless its 30mbps write and 120 mbps read -- on two 128gb micron c300 real ssds at sata 3 speeds...on a RAID set. turrible.

    1. Best Effort Test:  -provides background information.
    Donald  Speed
    0.08 Mbps
    0 Mbps
    0.25 Mbps
    Max Achievable Speed
     Donald speedachieved during the test was - 0.08 Mbps
     For your connection, the acceptable range of speeds is 0.05 Mbps-0.25 Mbps.
     IP Profile for your line is - 0.14 Mbps
    Down : 00.7
    Up :0.04
    Ping : 82.25
    Also here's hub Details again
    Hub Firmware Information
    Current firmware:
    Version 4.7.5.1.83.8.94.1.11 (Type A)
    Last updated:
    23/04/13
    ADSL Line Status
    Connection Information
    Line state:
    Connected
    Connection time:
    0 days, 00:12:25
    Downstream:
    6.25 Mbps
    Upstream:
    448 Kbps
    ADSL Settings
    VPI/VCI:
    0/38
    Type:
    PPPoA
    Modulation:
    G.992.1 Annex A
    Latency type:
    Interleaved
    Noise margin (Down/Up):
    11.7 dB / 27.0 dB
    Line attenuation (Down/Up):
    9.3 dB / 5.0 dB
    Output power (Down/Up):
    13.9 dBm / 12.3 dBm
    FEC Events (Down/Up):
    17 / 0
    CRC Events (Down/Up):
    0 / 0
    Loss of Framing (Local/Remote):
    0 / 0
    Loss of Signal (Local/Remote):
    0 / 0
    Loss of Power (Local/Remote):
    0 / 0
    HEC Events (Down/Up):
    0 / 0
    Error Seconds (Local/Remote):
    864 / 438

Maybe you are looking for

  • Iphone 4s upgraded to iOS 5.1 - outgoing calls impossible

    i bought my apple iphone 4s today here in germany. i updated the software to iOS 5.1, and outgoing calls are impossible to make. please help.

  • Links in web browser opposed to Adobe Pro

    I have a problem that I am trying to fix.  I have an intranet map application(opened in IE) that allows in house users to *click* a feature to open a general Information.pdf about that map feature (ie. street sign).  the general information pdf has l

  • How Do I Include Original Message Headers in Mail replies!

    Hi, I would very much like to have all of the orginal email headers of the email I am responding to in my email replies.  All I can get get is something like: "On Jan 16, 2014, at 10:13 AM, United Airlines, Inc. <[email protected]> wrote:" I want: "-

  • Actions, artboard, pdf

    Hi! Im wokring with PDF-files with some drawings in it. Working with Illustrator CS5.1 The pdf's originally artboard size is 2750mmx625mm and uses CMYK colors. I also got artboard size 3000mmx600mm I have about 50 pdf-files of those two sizes. I want

  • Stopping only one sound

    just looking to stop one sound without stopping all sounds with a buton click