Very slow Time Machine MacBook Pro Mid 2009

After installing Mavericks Back-up for my MacBook has become very slow. I checked firmware update as recommended by some, but that was rejected by the application provided for by Apple. Also a larger back-up device did not do the job. To back up 1.15 GB took about 30 mins. Before a back-up would take just minutes or maybe 1 hour, if I had not backed up for some days.
Any ideas?

Running Virtual Box and based on the number of 'Page Outs' swaps more RAM would be useful. Your MBP will accept up to 8 GB RAM with the following specifications: 204-pin PC3-8500 (1066 MHz) DDR3 SO-DIMM. The best sources of Mac compatible RAM are OWC and Crucial.
Ciao.

Similar Messages

How do I reinstall lion using time machine (Macbook Pro mid-2009)?

I am going to replace my hard drive (and add RAM) on my Macbook Pro (mid-2009) myself. I have Lion (10.7.4) currently, and have backed up via time machine on an external drive. I don't have Lion on a usb, and from what I read, Lion Recovery via internet isn't applicable for my macbook (pre 2010). Is the time machine backup a bootable drive? If so, then am I all good so long as my backup is completed prior to replacing the hard drive? If not, how do I create a bootable drive so I can get back to "normal"?
Thanks! :-)

To determine if your Time Machine backup has a Recovery HD on it restart the computer. Immediately after the chime press and hold down the OPTION key until the boot manager appears. A Recovery HD option should appear on your Time Machine backup drive. Select it and click on the arrow button below the icon. If all is well your machine should boot into the Recovery HD utilities screen.
If all is well then after you replace your drive boot from the Time Machine Recovery HD. Start by:
Drive Preparation for Lion
1. Select Disk Utility from the main menu and click on the Continue button.
2. After DU loads select your new hard drive (this is an entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Security button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
After finishing formatting quit DU and return to the main menu. Select the option to Restore from a Time Machine backup then click on the Continue button.

My macbook pro mid 2009 OSX Lion 10.7.4 randomly Hanging when backing up with Time Machine

My macbook pro mid 2009 OSX Lion 10.7.4 randomly Hanging when backing up with Time Machine to Time Capsule. Anyone else have this issue?

bumping this up. Same issues persist even with 10.7.5

Macbook Pro Mid 2009 Processor 2.26 GHz Intel Core 2 Duo, Memory 2 GB 1067 MHz DDR3. iOS 10.10.1 (14B25). My mac is running slow and have ran EtreCheck. Please help me fix my mac. Thanks!

Macbook Pro Mid 2009 Processor 2.26 GHz Intel Core 2 Duo, Memory 2 GB 1067 MHz DDR3. iOS 10.10.1 (14B25). My mac is running slow and have ran EtreCheck. Please help me fix my mac. Thanks!
Problem description:
My mac has been very slow lately. Any suggestions?
EtreCheck version: 2.1.2 (105)
Report generated December 14, 2014 at 8:15:29 PM PST
Hardware Information: ℹ️
MacBook Pro (13-inch, Mid 2009) (Verified)
MacBook Pro - model: MacBookPro5,5
1 2.26 GHz Intel Core 2 Duo CPU: 2-core
2 GB RAM Upgradeable
BANK 0/DIMM0
1 GB DDR3 1067 MHz ok
BANK 1/DIMM0
1 GB DDR3 1067 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
NVIDIA GeForce 9400M - VRAM: 256 MB
Color LCD 1280 x 800
System Software: ℹ️
OS X 10.10.1 (14B25) - Uptime: 0:54:52
Disk Information: ℹ️
Hitachi HTS545016B9SA02 disk0 : (160.04 GB)
S.M.A.R.T. Status: Verified
EFI (disk0s1) <not mounted> : 210 MB
MacHD (disk0s2) / : 159.05 GB (49.15 GB free)
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
HL-DT-ST DVDRW GS23N
USB Information: ℹ️
Apple Inc. Built-in iSight
Apple Internal Memory Card Reader
Apple Inc. BRCM2046 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Computer, Inc. IR Receiver
Gatekeeper: ℹ️
Mac App Store and identified developers
Startup Items: ℹ️
DVD3EnablerService: Path: /Library/StartupItems/DVD3EnablerService
Startup items are obsolete in OS X Yosemite
Problem System Launch Agents: ℹ️
[failed] com.apple.AirPlayUIAgent.plist [Details]
[failed] com.apple.CallHistoryPluginHelper.plist
[failed] com.apple.coreservices.appleid.authentication.plist [Details]
[failed] com.apple.icloud.fmfd.plist [Details]
[failed] com.apple.secd.plist [Details]
[failed] com.apple.security.cloudkeychainproxy.plist [Details]
[failed] com.apple.telephonyutilities.callservicesd.plist [Details]
Problem System Launch Daemons: ℹ️
[failed] com.apple.ctkd.plist [Details]
[failed] com.apple.icloud.findmydeviced.plist [Details]
[failed] com.apple.ifdreader.plist
[failed] com.apple.nehelper.plist [Details]
[failed] com.apple.softwareupdate_download_service.plist [Details]
[failed] com.apple.wdhelper.plist [Details]
[failed] com.apple.xpc.smd.plist [Details]
Launch Agents: ℹ️
[loaded] com.google.keystone.agent.plist [Support]
[invalid?] com.oracle.java.Java-Updater.plist [Support]
[not loaded] com.teamviewer.teamviewer.plist [Support]
[not loaded] com.teamviewer.teamviewer_desktop.plist [Support]
Launch Daemons: ℹ️
[running] com.adobe.ARM.[...].plist [Support]
[loaded] com.adobe.fpsaud.plist [Support]
[loaded] com.google.keystone.daemon.plist [Support]
[invalid?] com.oracle.java.Helper-Tool.plist [Support]
[not loaded] com.teamviewer.teamviewer_service.plist [Support]
User Launch Agents: ℹ️
[loaded] com.adobe.ARM.[...].plist [Support]
[invalid?] com.nds.pcshow.plist [Support]
[invalid?] com.nds.pcshow.uninstall.plist [Support]
User Login Items: ℹ️
None
Internet Plug-ins: ℹ️
WidevineMediaOptimizer: Version: 6.0.0.12757 - SDK 10.7 [Support]
FlashPlayer-10.6: Version: 16.0.0.235 - SDK 10.6 [Support]
QuickTime Plugin: Version: 7.7.3
AdobePDFViewerNPAPI: Version: 11.0.10 - SDK 10.6 [Support]
AdobePDFViewer: Version: 11.0.10 - SDK 10.6 [Support]
Flash Player: Version: 16.0.0.235 - SDK 10.6 [Support]
Default Browser: Version: 600 - SDK 10.10
Silverlight: Version: 5.1.30514.0 - SDK 10.6 [Support]
iPhotoPhotocast: Version: 7.0
3rd Party Preference Panes: ℹ️
Flash Player [Support]
Time Machine: ℹ️
Mobile backups: OFF
Auto backup: NO - Auto backup turned off
Volumes being backed up:
MacHD: Disk size: 159.05 GB Disk used: 109.90 GB
Destinations:
KINGSTON [Local]
Total size: 30.88 GB
Total number of backups: 0
Oldest backup: -
Last backup: -
Size of backup disk: Too small
Backup size 30.88 GB < (Disk used 109.90 GB X 3)
Top Processes by CPU: ℹ️
      6% WindowServer
      0% AppleSpell
      0% SystemUIServer
      0% powerd
      0% Google Chrome
Top Processes by Memory: ℹ️
131 MB softwareupdated
112 MB Google Chrome
41 MB Finder
34 MB Google Chrome Helper
32 MB WindowServer
Virtual Memory Information: ℹ️
51 MB Free RAM
587 MB Active RAM
551 MB Inactive RAM
350 MB Wired RAM
10.96 GB Page-ins
865 MB Page-outs
Diagnostics Information: ℹ️
Dec 14, 2014, 07:37:58 PM Install Adobe Flash Player_2014-12-14-193758_[redacted].crash
Dec 14, 2014, 07:21:27 PM Self test - passed

Please describe the problem in as much relevant detail as possible. The "etrecheck" fad hasn't made that step any less necessary. The usual results of posting etrecheck output on this site without a full description of the problem are very poor.
The many "failed" warnings that etrecheck sometimes spews mean nothing. Those warnings are not a reason to reinstall the OS, or to do anything else at all. They should be ignored.
The better your description of the problem, the better the chance of a solution.
For example, if the computer is slow, which specific actions are slow? Is it slow all the time, or only sometimes? What changes did you make, if any, just before it became slow? Have you seen any alerts or error messages? Have you done anything to try to fix it? Most importantly, do you have a current backup of all data? If the answer to the last question is "no," back up now. Ask if you need guidance. Do nothing else until you have a backup.

Updated my macbook pro mid 2009 to 10.9.4 and now it moves slow and rainbow wheels frequently

I updated my macbook pro mid 2009 to 10.9.4 and now it moves slow and rainbow wheels frequently. Is there a quick and easy fix? I tried looking online but things seemed very confusing. Any help would be appreciated.

I got a rainbow wheel when attempting to click on a pic in Iphoto. I can copy and paste the next time I have a problem but here is what I have so far.
9/16/14 2:37:23.138 PM iPhoto[1588]: This process is attempting to exclude an item from Time Machine by path without administrator privileges. This is not supported.
9/16/14 2:37:23.138 PM iPhoto[1588]: This process is attempting to exclude an item from Time Machine by path without administrator privileges. This is not supported.
9/16/14 2:37:23.138 PM iPhoto[1588]: This process is attempting to exclude an item from Time Machine by path without administrator privileges. This is not supported.
9/16/14 2:37:23.139 PM iPhoto[1588]: This process is attempting to exclude an item from Time Machine by path without administrator privileges. This is not supported.
9/16/14 2:37:23.529 PM iPhoto[1588]: CFURLGetFSRef was passed this URL which has no scheme (the URL may not work with other CFURL routines): /Applications/iPhoto.app
9/16/14 2:37:23.579 PM iPhoto[1588]: CFURLGetFSRef was passed this URL which has no scheme (the URL may not work with other CFURL routines): /Applications/iPhoto.app
9/16/14 2:37:23.591 PM iPhoto[1588]: CFURLGetFSRef was passed this URL which has no scheme (the URL may not work with other CFURL routines): /Applications/iPhoto.app
9/16/14 2:37:23.621 PM iPhoto[1588]: CFURLGetFSRef was passed this URL which has no scheme (the URL may not work with other CFURL routines): /Applications/iPhoto.app
9/16/14 2:37:24.078 PM iPhoto[1588]: ICAGetDeviceList_Deprecated-Has been deprecated since 10.5. Calls to this function in the future may crash this application. Please move to ImageCaptureCore
9/16/14 2:37:24.866 PM WindowServer[84]: disable_update_timeout: UI updates were forcibly disabled by application "iPhoto" for over 1.00 seconds. Server has re-enabled them.
9/16/14 2:37:24.919 PM WindowServer[84]: common_reenable_update: UI updates were finally reenabled by application "iPhoto" after 1.05 seconds (server forcibly re-enabled them after 1.00 seconds)
9/16/14 2:37:51.737 PM Mail[567]: [<_MCLibSasl2SaslClient: 0x600001abf800> mechanism: PLAIN security layer: no] Failed to start the SASL connection
SASL(-1): generic failure:
9/16/14 2:40:43.424 PM iPhoto[1597]: This process is attempting to exclude an item from Time Machine by path without administrator privileges. This is not supported.
9/16/14 2:40:43.424 PM iPhoto[1597]: This process is attempting to exclude an item from Time Machine by path without administrator privileges. This is not supported.
9/16/14 2:40:43.424 PM iPhoto[1597]: This process is attempting to exclude an item from Time Machine by path without administrator privileges. This is not supported.
9/16/14 2:40:43.425 PM iPhoto[1597]: This process is attempting to exclude an item from Time Machine by path without administrator privileges. This is not supported.
9/16/14 2:40:43.624 PM iPhoto[1597]: CFURLGetFSRef was passed this URL which has no scheme (the URL may not work with other CFURL routines): /Applications/iPhoto.app
9/16/14 2:40:43.629 PM iPhoto[1597]: CFURLGetFSRef was passed this URL which has no scheme (the URL may not work with other CFURL routines): /Applications/iPhoto.app
9/16/14 2:40:43.631 PM iPhoto[1597]: CFURLGetFSRef was passed this URL which has no scheme (the URL may not work with other CFURL routines): /Applications/iPhoto.app
9/16/14 2:40:43.635 PM iPhoto[1597]: CFURLGetFSRef was passed this URL which has no scheme (the URL may not work with other CFURL routines): /Applications/iPhoto.app
9/16/14 2:40:43.969 PM iPhoto[1597]: ICAGetDeviceList_Deprecated-Has been deprecated since 10.5. Calls to this function in the future may crash this application. Please move to ImageCaptureCore
9/16/14 2:40:58.282 PM WindowServer[84]: CGXGetConnectionProperty: Invalid connection 104295
9/16/14 2:40:58.282 PM WindowServer[84]: CGXGetConnectionProperty: Invalid connection 104295
9/16/14 2:40:58.282 PM WindowServer[84]: CGXGetConnectionProperty: Invalid connection 104295
9/16/14 2:40:58.283 PM WindowServer[84]: CGXGetConnectionProperty: Invalid connection 104295

My optical drive on my macbook pro mid 2009 series is not working all the time.

I have a Macbook Pro mid 2009 series and just recently my optical drive is not working all the time. At times it decides to not spin a disk that has been inserted in the drive. I am currently deployed in Afghanistan and this is one of the very few things i have to distract me from the day to day haul. This is something that just started to happen and its very fustrating since i have limited support for this.

Another help source (if you haven't already done so).
Go to your OS Help Menu. In the search field type dvd
Click on all the troubleshooting topics & Support Articles that pertain to your issue.
You can also do the same in Disk Utility. Open same up.
At the bottom left of the window, click on the purple button w/the "?" in the middle.
This will bring up the Help Menu.
===============
Try a different brand. Top forum favorites
CDs
FUJI
TDK
Verbatim
DVDs
Maxell
Verbatim
==============
Apple's Disc Burning Quick Assist
http://support.apple.com/kb/HT2801 Apple Portables: Troubleshooting the slot load optical disc drive
Make sure the DVDs are not dirty, smudged and/or scratched.
http://support.apple.com/kb/TS2000 Mac doesn't start up from install disc
http://support.apple.com/kb/HT2801 Apple Computers: Troubleshooting the slot-loading SuperDrive
*** Your drive may need cleaning. Cleaning kits can be purchased from any store that sells CD/DVDs. ***

Change Hard Drive MacBook Pro mid 2009

My hard drive is dying (the beach ball appears, concurrent with a sound that can only be described as a squeak, coming from, I assume, the hard drive. Then, the beach ball freezes and the machine can only be revived by a hard restart)
My Question; can I put a Seagate Momentus XT ST750LX003, 750GB, Bulk 2.5 ", 8GB Flash, SLC, 32MB Cache, 7200 U / min • SATA III 6.0Gb / s in a Macbook pro Mid-2009 15"?
Would be very grateful for a reply

Ask as many questions as you like, OK.
Basically yes they are all backward compatible except for the drives and or firmware on the drives that refuse to be backward compatible. Which drive they are I have no idea but mostly they are SSDs and not spinning HDD. The transfer rate on any spinning HDD is slow enough, even on the XT series, that if you have a SATA II bus the drive can't really fill it up, IE can't go over its theoretical Rated transfer speed and or the actual data rate it can handle.
The problem occurred on 2009 MBPs because some of the original cables used could not handle the extra data rate the XT series drive could deliver, both reading and writing to the drive.

How to make a MacBook Pro (mid 2009) work properly with a 3M Streaming projector?

Ok, so I have a MacBook Pro (mid 2009), a 3M Streaming projector and very annoying problem.
When I connect my MacBook Pro with a Mini Displayport to HDMI adapter to the 3M projector, I get a pink tint, like a filter over the image, it’s very frustrating.
This are the tests I’ve done:
1. I tried the adaptor and the projector on a different (more recent) Mac -> It worked fine.
2. I tried connecting my MacBook Pro to a different not HDMI but VGA projector -> It worked fine.
3. I used some Terminal code I found on the web to force the Mac to send RGB signal, don’t know if that has anything to do with it, but I tried anyway -> Didn’t work
So I’m confused, it’s not the physical port of my MacBook cause it worked fine with a VGA projector, It’s no the 3M projector and it’s not the Mini Displayport to HDMI adaptor cause it worked fine on a different Mac.
So what is it?
I’m totally desperate, I haven’t been able to solve this problem, so if you guys can help me you will be my heroes.
Thanks.
– 13" MacBook Pro (mid 2009) runing Mavericks.
– 3M Streaming projector Powered by Roku.

Yes as Clinton says this is correct.
I've used a Sata to USB connector which is only a few pounds instead of an enclosure for the clone, but then I wasn't keeping mt old HDD. But that's an option if you don't need it.
I also use Carbon copy cloner as this will clone your recovery partition as well. Apples disk utility will also clone drives but I'm not sure that it copy's the recovery partition.
I highly redomend my Samsung 840 pro 256Gb - it's about the fastest drive you'll get (nearly) but is backed by Samsung's unrivaled SSD reliability and 5 year warranty. I've also used an 840 basic model on an older macbook and was equally pleased.
Crucial's drives are reliable mac friendly drives but are somewhat slower on the write speeds vs the 840 Pro.
I'd avoid OCZ drives due to so many failures across their range although they do have great reviews and some models just edge the Pro on speed although it's fairly negligible.
As Clinton says, avoid the Samsung Evo drive. I wanted to buy this drive as it is a great drive - but there are many users that have had compatibility issues with it when installed in a Mac. This may rectified on a future firmware update possibly, but until it's proven I would avoid it for now.

Can intel 520 series SSD be installed in macbook pro mid 2009

This is some of the information for the 180g SSD I want to replace my HD in my 13" macbook pro mid 2009
25nm NAND Flash Memory
2.5” form factor
SATA 6.0 Gb/s performance
My computer though has this information for its hard drive:
Product:          MCP79 AHCI
Link Speed:          3 Gigabit
Negotiated Link Speed:          1.5 Gigabit
Description:          AHCI Version 1.20 Supported
I know that the SATA 6.0 will be backwards compatible with my connection, but I was wondering if I am going to hit any problems. I am going to do a full time machine backup so I can have everything cloned onto the SSD, but want to know before I buy the SSD

Recently installed same type of SSD (Intel 520 120GB) in our 2010 Macbook (white) and runs just as well as its big bro. No problems at all. Storage isn't an issue since most stuff's in the cloud these days and we carry large files around on a USB stick. Way to go!

Help on installing Snow Leopard on Macbook pro mid 2009

I have macbook pro mid 2009 with 10.5.8 upgrade as latest. I am planning to install snow leopard on it. However before i do that i will upgrade the hard disk to 500gb and ram to 8 gb. As i never done reinstalling os on mac My question is
Should i install the original os first (which is leopard) and then upgrade it to snow leopard and backup my files from time machine ?
or
Can i just install snow leopard and back up my files from time machine?
Thanks for your answers in advance

I would upgrade your system to Snow Leopard first, then backup the entire system to Time Machine. Then upgrade your hard drive install Mac OS X 10.6 then on the set up screen (Do You Already Own a Mac?" click the button that states "from a Time Machine backup".

My Macbook Pro mid 2009 after installing mavricks restarts instead of shutdown !

My Macbook Pro mid 2009 after installing mavricks restarts instead of shutdown !
The strange also that after shut it down with the power button & close the laptop screen, If i connected the power cord the laptop start booting !
I've reseted the SMC & PRAM but still the problem
Also repaired the disk permissions !
Please advice what shoudl i do ?
Note: alot of times while the laptop in sleep mode i hear the fans !, and it goes very hot if i put it in my laptop bag in sleep mode !
Regards
My Mac info:
- 15 inch.
- Mid 2009
- 2.8 Ghz Intel Core 2 Duo.
- 8 GB 1067 MHz DDR3.
- NVIDIA GeForce 9400M 256 MB + NVIDIA GeForce 9600M GT 512 MB.

Classic kernel panics. Run the Apple Hardware Test suite, extended tests at least twice, followed by Rember. See
OS X About kernel panics,
Technical Note TN2063: Understanding and Debugging Kernel Panics,
Mac OS X Kernel Panic FAQ,
Resolving Kernel Panics,
How to troubleshoot a kernel panic, and
Tutorial: Avoiding and eliminating Kernel panics for more details.

Negotiated Link Speed on MacBook Pro mid-2009 with Kingston SSDNow v300

Hi,
I have a mid-2009 MacBook Pro (13") with Kingston SSDNow v300 SSD drive with Mavericks OS X installed.
I've noticed from different forums that many users have the same problem that I have: SSD drive's Negotiated Link Speed is only 1,5 Gbps, although MacBook Pro mid-2009 should support 3 Gbps speed.
My system has EFI 1.7 firmware update (MBP55.00AC.B03) installed in and System Info says that 3 Gbps Link Speed should be possible:
NVidia MCP79 AHCI:
Vendor:    NVidia
Product:    MCP79 AHCI
Link Speed:    3 Gigabit
Negotiated Link Speed:    1.5 Gigabit
Physical Interconnect:    SATA
Description:    AHCI Version 1.20 Supported
Many users have tried to reset NVRAM and SMC and I have also done these steps, but with not any improvement.
Some users have mentioned that MacBook Pro mid-2009 has a poor SATA ACHI chipset (NVidia MCP79) and SATA III SSD drives won't work on SATA II speed unless SSD drive is forced to work on SATA II speed by firmware update or by some tweaking tool. Is there this kind of tool available for Kingston SSDNow v300?
One user says that he got 3 Gbps Negotiated Link Speed on Mountain Lion, but after installing Mavericks, speed dropped to 1,5 Gbps (https://discussions.apple.com/message/23549859#23549859).
So, is there any way to get Negotiated Link Speed to work on 3 Gbps on Kingston SSDNow v300 with MacBook Pro mid-2009 (for example by installing an older version of Mac OS X) or do I have to buy a new SSD drive from another manufacturer to get 3 Gbps Negotiated Link Speed to work on my machine?
If the last option (to buy a new SSD drive) is the only option, would it be wise to look for an older model, a SATA II drive, (maybe OCZ Vertex 2) to get 3 Gbps speed?
Thanks!

Hi
I was just as frustated as you after installing the Kingston v300. I mean it's a solidly built drive with the reliability of kingston (I've been using their RAM for years and years in my desktop PC without problems). Unfortunately, for a the last 3 months I had it in my 2009 unibody white macbook, it was stuck at link speed 1.5.
I've been searching in forums since then without any solution. Even the update for bios is not available for my model.
I just tried the SMC reset after reading the blog.
http://thenextweb.com/lifehacks/2010/12/04/how-when-why-to-reset-the-pram-smc-on -your-mac/#!w3XEY
On reboot, everything seemed faster, so I checked the negotiated link speed and it was at 3 instead of 1.5! Yay! Then I checked the disk transfer speed on Blackmagic Disk speed test and it roughly doubled from 138 to 260MB/s. Now, I'm not going to shutdown or restart...
I hope this post is useful for people like me stuck at 1.5 Gbps speed. Good luck

Macbook pro mid 2009, yosemite 10.10.2 bootcamp installation windows 7 problem

i have a macbook pro mid 2009 and yosemite 10.10.2 installed. my bootcamp is 5.1.3 and i cant install windows 7. every time i create the usb installer and restart the mac to install windows the usb installer dont appear. what i do?
I try to make a uefi usb installer but The screen frozen when i click on efi boot

Your Mac has (or used to have) a built-in Optical drive. You need a physical DVD for Windows and a USB2 flash drive for BC drivers. Bootcamp Info.plist modifications cause more problems than they resolve.
Your Mac is also not UEFI compliant, late 2013+ Macs are the first ones to be, so EFI boot will not work.
From the un-modified Bootcamp Info.plist file...
        <array>
                <string>MacBook7</string>
                <string>MacBookAir5</string>
                <string>MacBookPro10</string>
                <string>MacPro5</string>
                <string>Macmini6</string>
                <string>iMac13</string>
        </array>
        <key>PreUSBBootSupportedModels</key>
        <array>
                <string>MacBook7,1</string>
                <string>MacBookAir3,2</string>
                <string>MacBookPro8,3</string>
                <string>MacPro5,1</string>
                <string>Macmini4,1</string>
                <string>iMac12,2</string>
        </array>

No audio after Mountain Lion 10.8.3 update Macbook Pro Mid 2009

A few days ago I downloaded some updates for Mountain Lion on my Macbook Pro Mid 2009. After that there is no sound and internal speakers are not listed as an output device. The startup sound is still working (I would guess it uses the same speakers?) but nothing else makes a sound through the speakers. Also headphones are working. I'm not 100% sure if my OS version vas 10.8.2 before the update or not.
I have tried to input the headphones in and out many times to make sure that no microswitches are stuck. Also I have reset SMC and NVRAM/PRAM and reinstalled Mountain Lion. I even installed Lion (10.7.0) to be sure but it still won't work.
Any help would be appreciated.

Make a "Genius" appointment at an Apple Store.
Back up all data on the internal drive(s) before you hand over your computer to anyone. If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present.
Keeping your confidential data secure during hardware repair
*An SSD doesn't need to be zeroed.

I updated to OS X Mavericks and now trying to run Logic Pro X on a MacBook Pro mid-2009, using an M-Audio Axiom 49 and an M-Audio Fast Track Pro... Logic keeps telling me that Mac OS X MIDI Services are not available... How do I solve this problem?

I updated to OS X Mavericks and now trying to run Logic Pro X on a MacBook Pro mid-2009, using an M-Audio Axiom 49 and an M-Audio Fast Track Pro... Logic keeps telling me that Mac OS X MIDI Services are not available... How do I solve this problem?

I just checked to see if the update to OS X Yosemite 10.10.1 solved any of the issues outlined in my previous post, and to my dismay, nothing has changed -- all of the previous problems persist.
My iMac (8) -- it's renamed itself eight times since the recent troubleshoot with the Apple tech rep -- shows up as a shared device in Finder on my MacBook Pro, but when I click on it, I cannot establish a connection using "Connect As". So I've attempted to connect using the menu "Go/Connect to Server...", using both (alternately) the iMac's name and IP address, to no avail. I get a message which reads: "There was a problem connecting to the server 'Peter's iMac (8)'. This server may not exist or it is unavailable at this time. Check the server name or IP address, check your network connection, and then try again."
Here's what I know:
The server -- Peter's iMac (8) does exist;
The server -- Peter's iMac (8) is available at this time;
The server name -- Peter's iMac (8) -- is correct, as specified in the system sharing preferences;
The server IP address is correct, as specified in the system sharing preferences;
The network connection is active when I attempt to connect.
I'm convinced the problems stem directly from the OS X Yosemite update. None of this was ever remotely an issue in the previous OS X's -- any of them. This is maddening! What can be done? Apple?? Anyone???

Very slow Time Machine MacBook Pro Mid 2009

Similar Messages

Maybe you are looking for