VG224 box & analog phones with CCM3.3 - call problem

Hi
We have CCM3.3 at central location & at remote location with 2mb leased line have router & connected to LAN then VG224, analog phoenes.
Initially VG224 not reg, then it got reg with use of h323 procol config at both CCM & VG end.
Now 2 analog ph are connected at VG end and tring to call IP phone number which is got reg with CCM3.3.
Result: from analog ph able ring IP Phone but Ip phone cannot. And one more is from analog to IP Phone is one way, call initiator is getting voice from IP Phone. but IP Phones not able to hear anything.
Need solution & troubleshoot for the same.
Regards
Naga.

Hi,
try removing voice-class and use "codec g711u" instead under DP 4000.
Hope this helps, please rate post if it does!

Similar Messages

  • Any one using/deployed Telematrix phones with Cisco Call Manager

    Any one using/deployed Telematrix phones with Cisco Call Manager

    Yes, it does:
    Cisco Unified IP Phone Series 7900
    http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/compat/ccmcompmatr.html#wp51474
    Config on CUCM itself is no different from any other phones neither other requirements like DLUs.
    Of course you should already have APs for connectivity.
    HTH
    java
    if this helps, please rate

  • Analog phone with ring light

    We have analog phones in certain applications that use a neon light instead of a ring tone.  It requires 90v to activate the neon light. We have VG224 analog gateways which appear to not be able to push 90v.  Does anyone have a solution or is there another Cisco gateway that will support analog phones that use a neon light instead of a ring?

    BlackBerrys have a flashing red LED indicator light for new messages. It's hard to miss. And with the sleeve cases, there is a gap for keeping this notification light visible, even when holstered.

  • Setup Hotline Analog Phone with SCCP

    Anyone out there can help me out how to setup a hotline in CUCM 8.6?
    I've followed this procedure below, but I'm still getting an error message when I lift the handset such as "your dial cannot be completed...".
    http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_configuration_example09186a0080232b9f.shtml
    Just in a nutshell, here is what I've done:
    Extension: 1111 PLAR Analog SCCP Phone with: CSS_Hotdial and PT_Allowed (line settings)
    TP: blank, PT_Hotdial and CSS_Hotdial, and called PTM: 2222
    Extension: 2222 CSS_Allowed, and PT_Allowed - no changes on this extension...
    Added the PT_Allowed into CSS_Hotdial. The order is: PT_Hotdial/PT_Allowed
    Both lines are on the same VG204-vg20x-ipvoice-mz.124-22.T5.bin. When I selected hotline feature it says is supported Analog Phone SCCP, but I did not see the VG. It looks like is not supported hotline on VGs. Can someone confirm that?
    Am I missing something? Do I need to enable something under Service/Enterprise parameters?
    Thank you!

    Chris, thanks for your prompt help.
    I thought the TP needs a CSS with access to the 1111 DN, not to the 2222. Because when someone lifts the handset on phone 1111 this phone should invoke the TP which translate and ring to the 2222 phone. Thus, I put this CSS_Hotdial on phone 1111 under line.
    And my TP looks like this: PT_Hotdial and CSS_Hotdial, and called party transformation mask 2222
    The CSS_Hotdial has only access to one PT_Hotdial.
    Also the two phones 1111 and 2222 are on the same partition PT_Allowed, but they are on different CSS.
    Anyway I also tried what you said but did not work. Are you sure this hotline works on VG204? I think it is not working because this feature is not supported on VG204 nor in any VG model.
    If you are sure it should work. Could you please elaborate more this solution with PT/CSS/TP?
    Once again thanks

  • Firmware 1.1.2: Locking phone while on call problem

    I had upgraded my iPhone to firmware 1.1.2. This caused many problems so I had it swapped out by a Mac Genius. I recieved a new phone and recently upgraded it. I am having the same problems. When Im on a call and press the Sleep/Wake button, instead of locking the phone, it ends the call. Somebody try this please and tell me the result. I may have to contact Apple so they can fix this. Its rediculous! I do remember when I originally updated to 1.01 and 1.02 I expierienced this. I dont know why this happens. Please advise. (Ive already restored/reset/reboot AND REPLACED!) Thanks

    1st. Please stop bothering the people at apple with this issue
    2nd. The phone cannot and should not be changed to lock itself when you are on a regular call. The only way to lock the phone during a call is when you are using the headset/speaker.

  • Choppy voice on IP Phone with external calls

    Hi,
    Having a issue where the IP Phone side of the call hears choppy voice (jitter) on some external calls coming in/out a MGCP PRI Gateway across WAN from the users. The PSTN (outside party) is fine and doesn't hear a problem.
    The users can call other IP Phones at the main location fine and don't have this problem, problem is only with calls going out the PRI on the gateway now and then.
    QoS is in place and no drops on the policies.
    The WAN connection is a Multilink frame relay connection with 2 T1s. FRTS is configured and set to shape to 10ms with a fragment size of 1600 bytes.
    The 'mgcp playout adaptive' command was added and set to 250 which improved things a little and it happens less often then before but still there.
    The gateway is IOS 12.4(3b) and CCM is 4.1(3)Sr1 with 7.2(2) phone load on the 7940/7960 phones. Using G729 codec across WAN.

    Fragment size 1600 ? It should be quite smaller to be effective.
    Also, how big the the queues ? If too large, you can experience delay without drops.
    Finally, check your FRTS values and perhaps bumping up a little. More often than not WAN networks are a little more tolerant of what the contract guarantees.

  • Swiping to unlock the phone with incoming call.

    Swiping to unlock the phone doesn't respond well when I receive an incoming call. Can take a number of tries before its successful and I'm able to answer.
    Any ideas?

    Thanks for the respone, but the problem is ongoing and intermittent. A number of resets over the last few weeks haven't had any noticeable impact.
    I've had some succes with swiping the phone icon (on the right of the screen) up and then selecting the answer option.
    A similar problem happens when I have just received a text; I can't succesfully unlock the phone for a couple of seconds after I receive the notification.
    While this issue isn't making want to get rid of the phone it is still frustrating.

  • If apple app store has an app to sync windows phone with itunes called windows connector, and windows phone and apple are competitors, why doesnt apple make an app for android that syncs itunes without a third party software

    I want to simply sync my android and my mac itunes without downloading any software. Windows phone has an app to do that even though apple and windows phone are competitors. Why does android not make an app or why doesnt apple create an software or something

    Apple didn't create the Windows Phone app (Microsoft). Apple has nothing to do with this, and Google should do an app for this

  • Vg224 don't auto disconnect with analog phone

    Dear all ,
    why vg224 don't auto disconnect with analog phone? is the busy frequency dismatch between vg224 and analog phone?
    can you have any suggest to me ?
    thks.

    HI rrjoas45,
    thks your answer, I try to add a command with supervisory . but I discovery it isn't effective . the port status follow:
    sh voice port 2/0
    Foreign Exchange Station 2/0 Slot is 2, Port is 0
    Type of VoicePort is FXS
    Operation State is DORMANT
    Administrative State is UP
    The Last Interface Down Failure Cause is Administrative Shutdown
    Description is not set
    Noise Regeneration is enabled
    Non Linear Processing is enabled
    Non Linear Mute is disabled
    Non Linear Threshold is -21 dB
    Music On Hold Threshold is Set to -38 dBm
    In Gain is Set to 0 dB
    Out Attenuation is Set to 0 dB
    Echo Cancellation is enabled
    Echo Cancellation NLP mute is disabled
    Echo Cancellation NLP threshold is -21 dB
    Echo Cancel Coverage is set to 64 ms
    Echo Cancel worst case ERL is set to 6 dB
    Playout-delay Mode is set to adaptive
    Playout-delay Nominal is set to 60 ms
    Playout-delay Maximum is set to 250 ms
    Playout-delay Minimum mode is set to default, value 40 ms
    Playout-delay Fax is set to 300 ms
    Connection Mode is normal
    Connection Number is not set
    Initial Time Out is set to 10 s
    Interdigit Time Out is set to 10 s
    Call Disconnect Time Out is set to 60 s
    Supervisory Disconnect Time Out is set to 750 ms
    Ringing Time Out is set to 180 s
    Wait Release Time Out is set to 30 s
    Companding Type is u-law
    Region Tone is set for CN
    Analog Info Follows:
    Currently processing none
    Maintenance Mode Set to None (not in mtc mode)
    Number of signaling protocol errors are 0
    Impedance is set to 600r Ohm
    Analog interface A-D gain offset = -3.0 dB
    Analog interface D-A gain offset = -3.0 dB
    FXS idle voltage set to high
    Ring DC offset set to 0 volt
    Station name None, Station number None
    Translation profile (Incoming):
    Translation profile (Outgoing):
    Voice card specific Info Follows:
    Signal Type is loopStart
    Ring Frequency is 25 Hz
    Hook Status is On Hook
    Ring Active Status is inactive
    Ring Ground Status is inactive
    Tip Ground Status is active
    Digit Duration Timing is set to 100 ms
    InterDigit Duration Timing is set to 100 ms
    Hookflash-in Timing is set to max=1000 ms, min=150 ms
    Hookflash-out Timing is set to 400 ms
    No disconnect acknowledge
    Ring Cadence is defined by CPTone Selection
    Ring Cadence are [10 40] * 100 msec
    Ringer Equivalence Number is set to 1
    thks.

  • Cisco VG 224 Analog Phone Gateway

    Hi
    Can i use cisco vg224 gateway in a scenario like -
    cisco ISR+CCM express -->WAN LINK --> cisco ISR -> VG224 gateway --> analog phones.
    If this scenario is good then, can i do call transfer and forwarding with analog phones with any extensions digital/analog on that setup?
    thanks
    regards
    Rakesh
    =====

    The Cisco VG 224 is an analog voice gateway that manages up to 24 FXS ports for analog devices. Call control of the analog FXS ports is provided by Cisco CallManager or by a Cisco CallManager Express (Cisco CME) system. An SCCP telephony control (STC) application on the Cisco VG 224 functions as a a proxy to translate call-control messages between the call-control system (Cisco CallManager or Cisco CME) and the voice gateway.
    This URL should help you:
    http://www.cisco.com/en/US/products/ps6441/products_feature_guide09186a0080483a76.html
    http://www.cisco.com/en/US/products/ps6441/products_feature_guide09186a0080483a76.html

  • MWI on analog phone using stutter dial on VG248

    Someone is telling me that you can use stutter dial or some other method to light up an anolog phone Message waiting indicator using on a VG248. This is with an analog phone that has an Message light on it. Is this possible and if so is it possible using and ATA with Call Manager?

    Hi Shane,
    This does work with the VG248, we have used the "Stutter Dial Tone" on some analog phones and used the actual MWI Lamp on other analog phones with good success. Have a look;
    Choosing Message Waiting Indicator Type
    The VG248 supports several types of methods for sending MWI messages to analog phones. Because you might have different types of analog phones connected to the VG248, you can modify the MWI type on a per-port basis. So, if you have some analog phones that have MWI lamps on them, you can notify users of awaiting messages using the lamp. Or, you can choose to play a tone when users pick up their phones.
    Keep in mind that the VG248 only sends this information to the phones if it is received from Cisco CallManager. If Cisco CallManager is not integrated with your voice mail system, it does not send this information to the VG248.
    Step 1 From the main menu, choose Configure.
    Step 2 Choose Telephony.
    Step 3 Choose Port specific parameters.
    Step 4 Use the arrow keys to select the port to configure and press Enter.
    Step 5 Choose MWI type.
    Step 6 Choose from the following options:
    Lamp—illuminates lamp on phone
    Caller ID—uses caller ID mechanism to send MWI messages to the LCD screen on phone
    Stutter—plays tones when user picks up the phone
    Lamp + stutter—illuminates lamp and plays tone
    Caller ID + stutter—sends message to LCD screen and plays tone
    None—does not send MWI information
    From this doc;
    http://www.cisco.com/en/US/products/hw/gatecont/ps2250/products_configuration_guide_chapter09186a0080087de4.html#xtocid13
    Hope this helps!
    Rob
    Please remember to rate helpful posts..........

  • BT4500 with nuisance call blocker - strange number...

    I bought some BT4500 phones with nuisance call blocker. I have set it up to block withheld, international and payphone numbers. In general it works well, but I am getting more and more marketting calls from numbers which either 1) don't seem to conform to UK numbering (e.g. 0102055) or 2) look like international numbers (e.g. 0015183999915). My simple(?) questions are:
    1) How can I establish the origin of calls by their number? For example, if 0102055 is in the UK, it is presumably registered to someone and thus can be reported to TPS; and although 0015183999915 looks like an international number, is it? (because international callers do not usually have their number presented).
    2) If a number is international (number presented) why doesn't my nuisance call blocker send it straight to the answering machine?
    I had a lengthy chat to the BT help line but I couldn't get answers to these questions. They simply offered me a number change (don't want) and "choose to refuse" (only works for pre-specified numbers), and suggested international call barring (no good because I get some genuine international calls which go to the answering machine).
    Can anyone provide answers?

    Ribblelancs wrote:
    yasur wrote:
    Thank you for your replies. Even if some international numbers are being sent, then I would expect the nuisance call blocker phones to block them if I have "block international calls" set. I will try some experiments. Unfortunately, the blocking phones can block either on type (e.g. withheld, international) or on specific numbers, but not both. I suspect that blocking on number will be the start of a long term chase similar to blocking email addresses.
    Unfortunately, one of the popular externally fitted call blockers only has the features that you mention. i.e it is the same - you can do either/or, but not both.
    However it seems that most of them hold a database of known nuisance callers.
    My own phone (not a BT model) only blocks calls by numbers entered. It's quite effective, but does, as you say, take some time to filter out the junk callers.
    But the other popular external call blocker has many more features available. It can block anything , but known callers can be allowed through.
    toekneem
    http://www.no2nuisancecalls.net
    (EASBF)

  • Pick up group between analog Phone connected on VG224 with Cisco 7911 does not work?

    Hey guys,
    I had a problem, during a demo. My team was design a cisco callmanager 7.0 with 7911 IP Phone and with VG224 analog devices phones. I would like to know if there are some a problem of capability when configured a Analog Phone on VG224 in the same pickup group with Cisco IP Phone 7911.
    I got pickup between Analog phones but with I cannot pick up, between IP Phones and analog phones.
    Does anybody knows if has capability problem or could be a configuration problem.
    The feature has already enbled for pick up **3 (stcapp feature access-code).
    best regards
    Daniel

    Hi Daniel,
    Did you try **4
    The default settings for the VG224 feature codes are as follows:
    Call Forward All (CFA) **1
    Call Forward All Cancel **2
    Call Park Directed Call Pickup Directed **6
    Call Pickup Group **4
    Call Pickup Local **3
    Call Transfer = Hookflash
    Redial *#
    Speed Dial *01 to *99 for two-digit codes
    Speed Dial to Voice Mail Default prefix and code is *0 for one-digit codes, and *00 for two-digit codes
    http://www.cisco.com/en/US/docs/ios/12_4t/12_4t2/ht1vg224.html#wp1178205
    Hope this helps!
    Rob

  • I bought a iphone 4 from a guy on craigslist, I knew about ios 7.0 having the lock thing, but when I met him, his simcard was in the phone, I tested the phone with his simcard in from of him. The phone looked great with no problems and I even got the box

    I bought a iphone 4 from a guy on craigslist, I knew about ios 7.0 having the lock thing, but when I met him, his simcard was in the phone, I tested the phone with his simcard in from of him. The phone looked great with no problems and I even got the box with the accesories, so I knew it was his... I then did the reset on the phone (erase all data... from settings) and it went through and activated and everything was good... I used the phone for about a month with no problems at all, even had my apple ID in the icloud and everything... well ios 7.0.6 came out and I used my computer to restore the phone, because I feel that the cord and computer gives it a better restore, it did great no problems, and when it went to the part where I went to activate the phone, I get a enter your apple id and password to complete activation... Wait... why is this up i thought, I thought I did everything like I suppose to to succesfully switch it to me, the new owner... but now its asking for some C******@yahoo.com.... I only have @gmail.com emails and none start with a C... The guy sold me the phone because he was switching to Verizon, and I tried to call him, and now the number is disconnected... I guess he switched to Verizon with a new number... Now im stuck with a paperweight that costed me $200.00... What can I do at this point... Please help me... I restored it to give it to my Step Son as I just got me the iphone 5... Thank you for ANY HELP in advance... Thank you again.

    I bought a iphone 4 from a guy on craigslist, I knew about ios 7.0 having the lock thing, but when I met him, his simcard was in the phone, I tested the phone with his simcard in from of him. The phone looked great with no problems and I even got the box with the accesories, so I knew it was his... I then did the reset on the phone (erase all data... from settings) and it went through and activated and everything was good... I used the phone for about a month with no problems at all, even had my apple ID in the icloud and everything... well ios 7.0.6 came out and I used my computer to restore the phone, because I feel that the cord and computer gives it a better restore, it did great no problems, and when it went to the part where I went to activate the phone, I get a enter your apple id and password to complete activation... Wait... why is this up i thought, I thought I did everything like I suppose to to succesfully switch it to me, the new owner... but now its asking for some C******@yahoo.com.... I only have @gmail.com emails and none start with a C... The guy sold me the phone because he was switching to Verizon, and I tried to call him, and now the number is disconnected... I guess he switched to Verizon with a new number... Now im stuck with a paperweight that costed me $200.00... What can I do at this point... Please help me... I restored it to give it to my Step Son as I just got me the iphone 5... Thank you for ANY HELP in advance... Thank you again.

  • H.323 endpoint to analog phone call problem

    I have Tandberg H.323 endpoints registered in gatekeeper, Callmanager 4.2(1) and MGCP voice gateway to classic telephony. There is a problem, when I try to set up a call from H.323 endpoint to the analog phone through voice gateway. The call is set up but disconnets after about 3 seconds alerting signal. However you can have normal connection, when you answer the phone during theese three seconds of alerting. When it disconnects it says: 'Resource unavailable, unsecified'.
    What can cause such problem?
    Thanks in advance.

    NO, I was using an Sx-20 as the H323 endpoint. I tried a different video confernece unit.The other confernce unit worked with out any issues. Sorry I wish I new what was wrong with the sx-20. What kind of h323 endpoint are you using?

Maybe you are looking for