VGA.ini error during reboot?

Hi..
I have allmost pulling all my hairs out in frustation about this.
Every time I reboot it hangs on VGA.INI. So obviously Im thinking if its the graphicscard having trouble initializing when warm.
It starts everytime when cold and have been turned off for 30 minutes.
Besides that my machine is rock solid.
I have also checked USB devices bcause I suspected a conflict issue. But all is updated and doubled checked. ( suspected my Ideazon for making trouble.)
newest drivers etc.
Contacted MSI support but GEEE, they dont know jack. Totally ignored that I was referring to the D-LED2 on the mobo.
They asked me to reinstal system... CMON... If I do that I might aswell buy a new mobo!!!
Im ready to buy e new graphics card (about time for a new one).. But no Idea if the issue is another.
My sys is Asus 9800 gt, Eclipse SLI, i7

Quote from: Slunten on 26-July-11, 21:38:49
I was wondering about the PSU aswell... Its all stable, when up and running?
OK then ill give it a shot with a new Twin frozr tomorrow ( hopefully ). Cross my fingers.
thnx m8
Quote from: Slunten on 26-July-11, 21:38:49
I was wondering about the PSU aswell... Its all stable, when up and running?
This doesn't mean that's OK. The PSU can goes bad by many ways.
The only way to check is with a new powerfull enough and trusted PSU
Quote from: Slunten on 26-July-11, 21:38:49
OK then ill give it a shot with a new Twin frozr tomorrow ( hopefully ). Cross my fingers.
yeah

Similar Messages

In updating my iPod to 6.1.2, I received an error during the update. Now, ipod is not rebooting. Has screen showing usb to Itunes picture.   Turning off and back on it goes back to this picture. I don't know how to reset so that I can restore my backup

In updating my iPod to 6.1.2, I received an error during the update. Now, my ipod is not rebooting. It continues to display a screen showing usb to Itunes picture.   Turning off and back on, it goes back to this picture. I don't know how to reset so that I can restore from my backup.
A similar thing happened when I updated the ios on my ipad. But, I was able to reboot, and then restore from backup.   How can I get my ipod to reboot and allow restore when it is not even recognized as I reconnect to my computer?

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Error during iTunes 10 installation - iPod Service failed to start

Hi Everyone,
I am getting this error during installation of iTunes 10(Windows XP).
+*"Service (iPod Service)failed to start.Verify that you have sufficient priveleges to start system services."*+
*Can any of you please help?* I ignored it first and continued with the installation. Then tried to update iphone to iOS 4.1 which crashed. I had to go to Apple store to get my iphone restored. I am having trouble installing itunes and cannot restore data from backup.
I tried uninstalling itunes and deleted all itunes data as suggested by the guy at the Apple store. Still not working. Will appreciate if someone can help resolve this error. Thanks.

I just got off the phone with Apple tech support. The problem with that iPod Service is a problem with XP Service Pack 3, but can be fixed this way:
1. Right click on "My Computer", select "Properties"
2. Click on the Advanced tab.
3. in the Startup and Recovery section, click the Settings button.
4. Click the Edit byutton to edit your boot.ini file in notepad.
5. Look for "/noexecute=" in the file and change the word after the equals to "optin" (sorry - I don't remember what the original setting was anymore).
6. Save the file, close notepad, click the OK button on Startup and Recovery window, then reboot.
The warning message about the iPod Service should stop. Also, this helps with iPhones that are not recognized by Windows or iTunes after an install fails.

Error during Installation of OBIEE 11.1.1.6

Hi All,
I am facing following error during in installation of OBIEE 11.1.1.6 ON WIN 2008 SERVER. Before begin the installation I have done uninstall of OBIEE 11.1.1.5.
Any help would be appreciated.
*************** Trying to Start OPMN **************
*************** Executing Command **************
cmd /c C:\Users\S_ORAC~1\AppData\Local\Temp\Opmn1337233127128.bat
C:\Users\S_ORAC~1\AppData\Local\Temp>SET ORACLE_HOME=D:\OBIEE_Home\Oracle_BI1
C:\Users\S_ORAC~1\AppData\Local\Temp>CALL "D:\OBIEE_Home\instances\instance2\bin\opmnctl.bat" startproc ias-component=coreapplication_obiccs1
opmnctl startproc: starting opmn managed processes...
================================================================================
opmn id=pdc03srv160:9501
Response: 0 of 1 processes started.
ias-instance id=instance2
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
ias-component/process-type/process-set:
coreapplication_obiccs1/OracleBIClusterControllerComponent/BIClusterController/
Error
--> Process (index=1,uid=151980586,pid=2976)
time out while waiting for a managed process to start
Log:
none
java.lang.Exception: opmnctl task failed
     at oracle.as.install.bi.biconfig.standard.OpmnctlTask.doExecute(OpmnctlTask.java:74)
     at oracle.as.install.bi.biconfig.standard.AbstractProvisioningTask.execute(AbstractProvisioningTask.java:70)
     at oracle.as.install.bi.biconfig.standard.StandardProvisionTaskList.execute(StandardProvisionTaskList.java:61)
     at oracle.as.install.bi.biconfig.BIConfigMain.doExecute(BIConfigMain.java:113)
     at oracle.as.install.engine.modules.configuration.client.ConfigAction.execute(ConfigAction.java:371)
     at oracle.as.install.engine.modules.configuration.action.TaskPerformer.run(TaskPerformer.java:88)
     at oracle.as.install.engine.modules.configuration.action.TaskPerformer.startConfigAction(TaskPerformer.java:105)
     at oracle.as.install.engine.modules.configuration.action.ActionRequest.perform(ActionRequest.java:15)
     at oracle.as.install.engine.modules.configuration.action.RequestQueue.perform(RequestQueue.java:64)
     at oracle.as.install.engine.modules.configuration.standard.StandardConfigActionManager.start(StandardConfigActionManager.java:160)
     at oracle.as.install.engine.modules.configuration.boot.ConfigurationExtension.kickstart(ConfigurationExtension.java:81)
     at oracle.as.install.engine.modules.configuration.ConfigurationModule.run(ConfigurationModule.java:86)
     at java.lang.Thread.run(Thread.java:662)
Executing Task: Executing: opmnctl start coreapplication_obis1
Regards,

Hi,
Please double check your looback adaptor configuration
The issue has been identified as that for some reason there is a hardcoded machine name mistakenly placed in the Solaris version of OBIEE, which is being sent out to be resolved by DNS. This machine name is an internal oracle machine, and so DNS can not find it.
This has been reported as the following bugs:
Bug 12804924 - OBIEE 11.1.1.5.0 INSTALLATION FAILS IN CONFIG PHASE WHEN STARTING COMPONENTS
Bug 12790815 - AFTER WHAT APPEARS TO BE A GOOD INSTALL CANNOT RESTART ANY OBIEE SERVICES
Solution:
As a workaround, Add the following entry to the end of your hosts file with a dummy IP address (e.g. 127.0.0.1) and then reboot:
127.0.0.1 stafas12.us.oracle.com stafas12
This should prevent timeout while checking DNS to resolve that non-existing address.
http://download.oracle.com/docs/cd/E14571_01/relnotes.1111/e10132/biee.htm#CACEFIAG
Reference: My oracle Support document
OBIEE 11.1.1.5 Installation On Solaris 64-bit Fails At Starting OPMN Managed Processes [ID 1380777.1]
OBIEE 11g: Error: "failed to start a managed process after the maximum retry limit" OPMN Fails to Start When Installing OBIEE on 64-Bit Operating System [ID 1305993.1]
Thanks
Deva
Edited by: Devarasu on May 18, 2012 10:57 AM

Received an error during 10.4.11 Update and now can not boot

I downloaded the 10.4.11 update and tried to install it on my Macbook Pro that had 10.4.10 and there was an error during the update and it stopped. I closed the window and tried again and had the same result. Now, when I try to boot my computer, it gets to the screen with the progress bar for loading Mac OS, though the progress bar does not go anywhere and the desktop never loads.
At this point I am only really concerned with accessing some files on my mac. I placed the restore disk that came with my Macbook Pro into it and rebooted, though it went to the same progress bar screen.
1. Does anyone have any advice on what I can do?
2. Anyone have any advice for how I can just access my files?
Thanks!

If you have a backup on a separate drive, especially a bootable one, your files are there (backup is imperative with any computer system). If not...
If you buy an external firewire drive (and some USB drives), you can install Tiger on that drive from your regular installation DVD, then boot from that new, external drive. You should be able to mount your internal system drive and copy all of your important files to the new external drive. Applications won't generally copy successfully.
Also, here is an article about backup and restore for important OS X 10.4 files:
http://docs.info.apple.com/article.html?artnum=301239
Now you have a consistent backup.
Get your original Tiger installation DVD and do an "archive and install" on your system disk. If it is successful, you will still have all of your data and most (not necessarily all) of your applications.
I just did this last night for my father in law. The "archive and install" actually failed probably due to a read error on the Tiger DVD installation disk. Fortunately, I have another one, and did an "update" install from that one. Many preferences were lost and some drivers evaporated (like Midi drivers for Logic Express), but generally, things worked well. His data was there, though I didn't trust it all
I then did all of the software updates, but NOT including 10.4.11 since that has caused some issue. I also had to reinstall iLife '08, but everything else worked.
I restored his iphoto and itunes libraries after doing all the updates from the backup I'd made earlier just to make sure everything was OK. It was.
He is now up and running without further problems.
Ed Oates

6.0.3 Error During Disc Initialization for both DVD+R and Disc Image - Help

I've been a mac user for a few years now, but I just bought a new MacBook, and my first superdrive! I'm all excited to test out the new hardware along with iDVD.
I've made a rather simple DVD setup and the first time through it was encoding for about an hour and then it gave an error message which I don't recall other than it mentioned QT7. I ran updater, no new updates that I needed and I tried again, and from then on I've been getting the Error During Disc Initialization message when burning to my DVD+Rs or when I try and save as a disc image (yes, I've deleted the encoding assets). I have about 20GB free on HDD, and I'm trying to burn approx. 100min of video. I've rebooted multiple times, and I've remade my project a couple times but no dice.
Any idears?
Mac OS X (10.4.8)

What hardware do you have???
You didn't answer Sue's question about free space on
your start-up drive. You should have 20GB+ free.
What are you sending to iDVD?
Verbatim DVD-R, not DVD+R, are very reliable, unlike
TDK and Memorex.
Also look here:
http://docs.info.apple.com/article.html?artnum=302925
I am running on a 2.0 ghz MacBook with a SuperDrive using Sony DVD+R. I will definitely pick up some Verbatim DVD-Rs though to see if that makes iDVD happy.
I have cleared up some room and now I have around 50GB free.
I am trying to make a DVD of two seperate .mp4s of a soccer game. I have 3 pictures and two buttons.

Error during installation of AI16E4: device cannot start (code 10)

I'm setting up this pcmcia board on a windows xp. I've tried nidaq 7 and 6.93, but I seem to get the same error - code 10 any ideas?

AOMdesign,
At what point in the process are you getting error 10? During the driver install? While trying to detect the card in MAX? While trying to run a program that calls the driver?
If you get the error during the install and you are installing off a CD, I suggest copying the CD's contents to the hard drive and installing from there. That usually takes care of installer errors. Also, be sure that the card is NOT in the computer while installing the software. If the card was in the computer while doing the driver install, uninstall the driver, shut down and remove the card, reboot and install the driver, then power down and reinsert the card, then power back up. These are two of the most common installation fixes.
If something else is causing the err
or or if those suggestions do not fix the issue, please post details of where the error is occuring and what you have already tried here so it can be discussed further.
RossC

After disk recovery, restoration incomplete error - error during PININST_BBV - and can't access BIOS

Hi I haad got :Ultrabook HP ENVY 6-1103el
I performed a disk recovery (with disks made myself) to wipe the hard drive. Got to disk 4 of 4 when HP Recovery Manager window appeared with following error message when I click the Details button:
ctoerror.flg file
[21:12:12.07] ChkErrBB.CMD : Detect some error during PININST_BBV.
[21:12:12.07] ChkErrBB.CMD : Check c:\system.sav\logs\BurnBootWarn.log
[21:12:12.07] ChkErrBB.CMD : or, check c:\system.sav\logs\BurnBootMerge.log
[21:12:12.08] ----------------------------------------
[21:12:12.08] Critical error condition was detected at BBV1...
[21:12:12.08]
[21:12:12.08] Refer the following file if exists.
[21:12:12.08] - c:\system.sav\Logs\BurnBootWarn.log
[21:12:12.08] - c:\system.sav\Logs\BurnBoot.log
[21:12:12.08]
[21:12:12.08] Switch to 2ndCap's WinPE and show [Recovery Manager]'s Incomplete dialog.
[21:12:12.08] because RM's dialog can't appear on [Start] screen on Win8 environment.
[21:12:12.08] customer may not notice RM already shows Error dialog.
[21:12:12.08]
[21:12:12.08] ----------------------------------------
there might be unexpected reboot during BBV Clean or Last...
The process will cause CTO panic because the image might not be normal...
There are 3 options, Save Log, Details, Retry. When I try 'Retry' it asks for recovery media. I've put my recovery disk 6 and disk 1 in, but nothing happens. Oddly enough, the command prompt (cmd.exe) is open at this point. Now whenever I restart the laptop it goes to the same restoration error screen with the command prompt open and minimized in the lower left hand corner.
Pressing F10 (BIOS Setup) or F11 (System Recovery) after starting doesn't do anything, it just goes straight the the Restoration Incomplete message. Pressing Esc during start goes to the Startup menu, but pressing F10 or F11 there just does the same thing. F2 System Diagnostics works. I ran quick memory check, everything passed. I ran the long hard drive check. Overall it passed, and each one passed except for optimized dst it said 'not available'. When I choose BIOS Management from Diagnostics UEFI, and try either a BIOS Update or BIOS Rollback, I get 'The selected BIOS image was not available.' My system's BIOS ID is F.23. When I try to select a BIOS Image to apply, I've clicked through the file trees and there's nothing there to choose.
I tried recovering the BIOS pressing Windows and b key when starting. The screen stayed blank and the caps lock light kept flashing but nothing happened. The screen just stayed blank and no bios update screen appeared.
Did my BIOS become corrupted during the system restoration from disk?
Any suggestions or options?
Thanks.

Hi larag,
Thank you for your reply.
As I stated in my original post, I suggest you contact HP support and explain in detail the events that happened, when you tried to do the recovery. The contact information is in my original post.
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

After USB recovery, restoration incomplete error - error during PININST_BBV.

I performed a USB recovery with USB made by Creating Recovery to wipe the hard drive.following error message when I click the Details button:
ctoerror.flg file
[ 1:06:44.60] ChkErrBB.CMD : Detect some error during PININST_BBV.
[ 1:06:44.60] ChkErrBB.CMD : Check c:\system.sav\logs\BurnBootWarn.log
[ 1:06:44.60] ChkErrBB.CMD : or, check c:\system.sav\logs\BurnBootMerge.log
[ 1:06:44.60] ----------------------------------------
[ 1:06:44.60] Critical error condition was detected at BBV1...
[ 1:06:44.60]
[ 1:06:44.60] Refer the following file if exists.
[ 1:06:44.60] - c:\system.sav\Logs\BurnBootWarn.log
[ 1:06:44.60] - c:\system.sav\Logs\BurnBoot.log
[ 1:06:44.60]
[ 1:06:44.60] Switch to 2ndCap's WinPE and show [Recovery Manager]'s Incomplete dialog.
[ 1:06:44.60] because RM's dialog can't appear on [Start] screen on Win8 environment.
[ 1:06:44.60] customer may not notice RM already shows Error dialog.
[ 1:06:44.60]
[ 1:06:44.60] ----------------------------------------
there might be unexpected reboot during BBV Clean or Last...
The process will cause CTO panic because the image might not be normal...
Laptop purchase on July 2013. System updated to 8.1. When recovered from USB to win8, errored. Tried to change BIOS time, didn't work

Hi @John90 ,
Here is a link that might help. The only other thing you could try is borrowing a copy of the exact same Windows 8 version as yours.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Detect some error during PININST_BBV HP envy-15035eo

Hello!
I just bought a new Samsung SSD 840EVO to my HP Envy-15035eo running Windows 8.1. I popped the SSD in to my computer an ran the recovery I bought from HP. After the computer reboots a couple of times the recovery restars and go back to the initall stepps of the recovery. Then if i pull out the USB-drive and reboot the computer ill get the message
"The recovery attemt har failed. Select one of the following buttons: Save log , Details. Retry". If i press "Details" I will get the following message:
"ChkErrBB.CMD : Detect some error during PININST_BBV.
ChkErrBB.CMD : Check c:\system.sav\logs\BurnBootWarn.log
ChkErrBB.CMD : or, check c:\system.sav\logs\BurnBootMerge.log"
I have tried to do a recovery after I load setup deafaults in the BIOS and enabled Legacy support. I have even done a Start up test on the new SSD and it passes the test.
Any help would be greatfull! Thanks!

1) Try Recovery - "Detect error during PININST_BBV – Fix: Set BIOS to Factory Defaults
•Boot computer – immediately click / press F10 to get into the BIOS Manager.
•Click on F9 to set the BIOS to factory default.
•Save and Exit
•Redo the Recovery – remember to leave the wireless light “on” during the Recovery... Didn't work for me
2) Set System Date to 8/4/2012 and Redo Factory Reset and System Recovery... Didn't work for me
Ignition75 states "I managed to get the recovery to work, by changing the system date in BIOS to 2012."
3) Set BIOS to factory default, System Date to 8/4/2012 and performed Minimized Recovery (based on one of these posts)... Successful Minimized Recovery... Set BIOS to factory default, System Date to 8/4/2012 and performed Factory Reset... SUCCESS
Don't know what, how, or why it worked... but it worked.
Please try the above suggestions and report back with your findings.
If you have any further questions, please don't hesitate to ask.
Please click the White KUDOS "Thumbs Up" to show your appreciation
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Error during ABAP 7.01 trial version install on Vista - installation exited

im re-installing NSP trial version for the 5th time and get the error below. I followed all instructions:
- removed old installation folders
- removed th port numbers in services
- switched off AV and firewall
- removed entries from registry
- ran the regtool
- rebooted system
but still get the error below - can you please help
details
win vista enterprise SP1
intel dual core 2.8 GHz
RAM 2GB
100GB free space
32 bit os
im on a netwkr so no need for the loopback...
(May 18, 2010 6:32:25 PM), Install, com.sap.installshield.maxdb.maxdb_call_sdbinst, err, An error occurred and product installation failed. Look at the log file C:\sapdb\NSP\log.txt for details.
(May 18, 2010 6:32:25 PM), Install, com.sap.installshield.maxdb.maxdb_call_sdbinst, err, ProductException: (error code = 601; message="An Error happened during call of MaxDB Tool sdbinst. Check end of Logfile C:/Users/XXXXX/AppData/Local/Temp/MaxDBSAPNWPREV.log")
STACK_TRACE: 22
ProductException: (error code = 601; message="An Error happened during call of MaxDB Tool sdbinst. Check end of Logfile C:/Users/whittyj/AppData/Local/Temp/MaxDBSAPNWPREV.log")
     at com.sap.installshield.maxdb.maxdb_call_sdbinst.install(maxdb_call_sdbinst.java:193)
     at com.installshield.product.service.product.PureJavaProductServiceImpl.installProductAction(Unknown Source)
     at com.installshield.product.service.product.PureJavaProductServiceImpl$InstallProduct.getResultForProductAction(Unknown Source)
     at com.installshield.product.service.product.InstallableObjectVisitor.visitComponent(Unknown Source)
     at com.installshield.product.service.product.InstallableObjectVisitor.visitInstallableComponents(Unknown Source)
     at com.installshield.product.service.product.InstallableObjectVisitor.visitProductBeans(Unknown Source)
     at com.installshield.product.service.product.PureJavaProductServiceImpl$InstallProduct.install(Unknown Source)
     at com.installshield.product.service.product.PureJavaProductServiceImpl.installProduct(Unknown Source)
     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     at sun.reflect.NativeMethodAccessorImpl.invoke(Unknown Source)
     at sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source)
     at java.lang.reflect.Method.invoke(Unknown Source)
     at com.installshield.wizard.service.LocalImplementorProxy.invoke(Unknown Source)
     at com.installshield.wizard.service.AbstractService.invokeImpl(Unknown Source)
     at com.installshield.product.service.product.GenericProductService.installProduct(Unknown Source)
     at com.installshield.product.service.product.PureJavaProductServiceImpl.installAssembly(Unknown Source)
     at com.installshield.product.service.product.PureJavaProductServiceImpl.access$900(Unknown Source)
     at com.installshield.product.service.product.PureJavaProductServiceImpl$Installer.execute(Unknown Source)
     at com.installshield.wizard.service.AsynchronousOperation.run(Unknown Source)
     at java.lang.Thread.run(Unknown Source)
from /AppData/Local/Temp/MaxDBSAPNWPREV.log
Tue May 18 18:32:24 GMT 2010 MaxDB sdbinst: checking unpacked archive... ok
Tue May 18 18:32:24 GMT 2010 MaxDB sdbinst: installation of MaxDB Software finished successfully Tu, May 18, 2010 at 13:32:23
Tue May 18 18:32:24 GMT 2010 MaxDB sdbinst: creating database NSP...
Tue May 18 18:32:24 GMT 2010 MaxDB sdbinst: getInstalledReleasesWin(): wrong version format
Tue May 18 18:32:24 GMT 2010 MaxDB sdbinst: ERROR: Backup check for 'C:\sapdb\NSP\_tempLocation\load\load_datasave' failed:
Tue May 18 18:32:24 GMT 2010 MaxDB sdbinst: File not found: C:\sapdb\NSP\_tempLocation\load\load_datasave
Tue May 18 18:32:25 GMT 2010 MaxDB sdbinst: installation exited abnormally at Tu, May 18, 2010 at 13:32:23
Tue May 18 18:32:25 GMT 2010 MaxDB: Error during call to sdbinst, rc= 1
Tue May 18 18:32:25 GMT 2010 MaxDB: Done with call_sdbinst
Tue May 18 18:32:25 GMT 2010 MaxDB: rc of sdbinst = 1
Tue May 18 18:32:25 GMT 2010 MaxDB: Start of CallSdbuninst
Tue May 18 18:32:25 GMT 2010 MaxDB: IndepProgPath: C:/sapdb/programs
Tue May 18 18:32:25 GMT 2010 MaxDB: dbmcli path: C:/sapdb/programs/pgm/dbmcli.exe
Tue May 18 18:32:25 GMT 2010 MaxDB: Calling check for db_enum in case of an abort
Tue May 18 18:32:28 GMT 2010 MaxDB: nsp doesn't exist. Nothing to do !
Tue May 18 18:32:28 GMT 2010 MaxDB: rc of Method: 3
Tue May 18 18:32:28 GMT 2010 MaxDB: IndepProgPath = C:/sapdb/programs
MaxDB: dbmcli_path = C:/sapdb/programs/pgm/dbmcli.exe
MaxDB: Database instance to drop: :NSP:
MaxDB: Instroot of NSP is: null
MaxDB: sdbuninst_option = :3
MaxDB: 0=uninstall all, 1=uninstall Kernel package, 2=drop database only, 3=do nothing
Tue May 18 18:32:28 GMT 2010 MaxDB: End of CallSdbuninst
Tue May 18 18:32:28 GMT 2010 MaxDB: End of uninstallation
Edited by: Joe Whitty on May 18, 2010 8:54 PM

I a similar problem several times trying to get my AbapTrial version to work but then everything was successful as below:
i. windows command regedit ->software and delete the whole SAP folder
ii. at least disable the services (I had old SAP.. entries) (you did windows command sc delete)
iii. I had an NSP version and so deleted the whole of C:SAP folder and c:sapdb folder
iv. I went to windows software management and removed the trial version or went to Start->Programs and deleted the Trial version there.
v. In Start->Programs->MaxDB (or, once, in software management) I deleted all MaxDB entries.
As far as I remember everything was then removed.
The successful installation then was as follows:
I successfully downloaded from http://www.sdn.sap.com/irj/scn/nw-downloads and successfully ran the installation:
1) the download wasnt possible the first few times I tried - the download popup did not appear and I received a message with the word "scnsorry" instead. I just had to keep trying.
2) I downloaded the entry
"SAP NetWeaver 7.01 SR1 SP3 ABAP Developer Edition ".
Another entry, also offered for download, "SAP NetWeaver 7.01 - ABAP Trial Version " did not install and seemed to be in error. (Installed "successfully" in just 4 minutes and showed no MaxDB files in the unzipped folder).
3) I followed the instructions and the installation (some 27 steps) ran for 7 hours.
4) I am on a laptop with Windows Vista 6.0 Build 6002 SP2. (It is in German, not English, but this was not a problem, although it is sometimes mentioned that one should use an english-language OS).
5) After installation I could log on at once.
I recommend this way because it saves so much time.
What put me on the right path was a comment by Markus Doehr on In AbapTrial7.01 NSP the Dispatcher stops after 1:15 minutes.

Error during recovery while upgrading Windows 8

When I upgraded Windows 8 on my HP Spectre Touchsmart Ultrabook 15t-4000 it failed during reboot. It nows comes up in recovery mode but says:
Your PC needs to be repaired
The Boot Configuration Data file is missing some required information
File:\BCD
Error code: 0xC0000034
When I continue, Windows boots after a long pause and presents the "Choose keyboard"screen. When I select English it goes to the screen with the troubleshooting icon. From there I have attempted automatic repair which fails with the error "The drive where windows is installed is locked". I have also attempted refresh, reset, and recovery manager and have not been able to get any of them to work.
What can I do to get my system back up?

Thanks for you advice.
I am having what I understand is not unique. I want to upgrade to Windows 8.1 but get a non working computer after the 'setting up devices' gets to about 54%. I have read that a start into safe mode, disabling the video driver on startup and then an update to the latest graphics driver for Intel graphics 4000 will solve the problem. HP says do not upgrade now.
Two questions: 1) Does the work around work? 2)Will HP tell me when I can upgrade nomally?
This is important because I can't find a way to recover from a backup on this frustrating machine that has the 32 gigabyte quick start flash unit working with my hard drive. I have to start over again from factory fresh with the usb stick every time.
Thanks for a response.

Getting error during the Oracle9i installation "Oracle9i Database Release 2 (9.2.0.1.0) for Compaq Tru64 machine"

Hi All,
Getting follwing error during the Oracle9i installation “Oracle9i Database Release 2 (9.2.0.1.0) for Compaq Tru64 machine"
u01/app/oracle/product/9.2.0/install/make.log
- Linking Oracle
rm -f /u01/app/oracle/product/9.2.0/rdbms/lib/oracle
cc -L/u01/app/oracle/product/9.2.0/lib/ -L/u01/app/oracle/product/9.2.0/rdbms/lib -o /u01/app/oracle/product/9.2.0/rdbms/lib/oracla
ld:
load_whole_file: Could not malloc 31328. bytes, for /u01/app/oracle/product/9.2.0/lib//libn9.a(asndata.o), didnt attempt to mmap
Stop.
*** Exit 1
While checked the memory details in the machine its showing plenty of free virtual memory.
# ps aux
USER PID %CPU %MEM   VSZ RSS TTY      S STARTED         TIME COMMAND
oracle     1353 0.6 27.2 601M 555M pts/2    S N 09:14:07 5:49.67 /tmp/OraInstall2014-01-21_09-14-02AM/jre/bin/../bin/alpha/native_threads/java -Doracle.installe
root       3033 0.0 0.4 10.4M 7.7M pts/0    R + 10:59:44 0:00.06 ps aux
oracle     1351 0.0 0.0 2.46M 320K pts/2    I N 09:14:02 0:01.36 ksh /tmp/OraInstall2014-01-21_09-14-02AM/installer -Doracle.installer.library_loc=/tmp/OraInsta
oracle     1277 0.0 0.0 2.48M 312K pts/2    I + 09:02:44 0:00.04 -ksh (ksh)
root       1269 0.0 0.0 2.56M 232K pts/2    I    09:01:23 0:00.01 -sh (sh)
root       1268 0.0 0.0 5.31M 768K ??       I    09:01:22 0:00.11 /usr/bin/X11/xterm -ls
root 1 0.0 0.0 608K 96K ?? IL   08:45:31     0:00.08 /sbin/init -a
root 0 0.0 3.9 2.52G 79M ?? R < 08:45:31     0:23.16 [kernel idle]
And I have rebooted the machine still also getting the same error.
Is there any way to resolve this issue??
Regards
prasanta

Pl elaborate the business / technical reason for installing a 15+ year old unsupported software on a 15+ year old unsupported hardware, assuming you are installing an a supported OS version
HTH
Srini

Detect some error during PININST_BBV HP Envy 4-1130ew

Welcome.
My problem is with the recovery kit with usb.
Error Detect some error during PININST_BBV
I did it in the bios as reported on
http://h30434.www3.hp.com/t5/Notebook-Recovery/quot-Detect-some-error-during-PININST-BBV-quot/td-p/2...
So F9 and enter.
And still nothing.
The computer has been added frames with 6 gb ram 16gb.
The computer is not guaranteed.
Is it possible that by adding ram recovery does not work?

Thanks for the reply.
Unfortunately, it did not help.
There is still this error message.
Date in the bios I changed after every reboot.
I set 01.01.2012.
at włanczaniu bios change date on 07.03.2012 (from what I remember)
I tried to upload a clean windows 8.1
the pendrive.
The installation went fine.
The product key fits into the bios.
Compuer works.
Only I still have the impression that it is you should not take place in this way.
If you have the original system compuer windows 8.
I bought extra recovery kit by serial number of the computer.
That's why it does not work.
I spent money (again) on the original system.
And I am forced to upload another and combining to make it work.
I do not understand this policy.
The problem I think is not resolved.
Please send me any other suggestions.

Error during building

hello,
i am trying to burn a dvd from idvd using professional encoding. twice at the end of burning (4 hours later) i get a message saying there has been an error during building (multiplexing?) i burned the same idvd project using high encoding and everything seemed to work ok. i want to try the pro encoding to see if there is a difference in quality.
another question... my project is in widescreen and looks great on my computer but in my dvd player, on my tv it's a bit stretched. why would this happen and can i fix or avoid it?
thanks for any advice
jean

Hi
Multiplex error is a very complex problem due to many things (long long list following) - on common but not obvious reason is that material on the iDVD menu goes outside the TV-Safe area (or just touching it).
So first - turn on TV-Safe area and move any object well inside of this.
Wide screen stretched - usually (as I think) it is due to making a 4x3 movie in a 16x9 wide-screen project OR the other way around. This forces one to on flat-screen TV (or other) set the presenting view right - My has 4x3, wide-screen, zoom and auto-wide-screen and I have to switch this by my remote for some DVD I've made "wrong" way.
Now my long long list on Multiplex Error
LONG LONG LONG LIST
Multiplexing Error
PART One.
Use of strange video/audio material eg .avi, .wmv, .mp3 etc.
I only use.
Video - StreamingDV (miniDV tape via FireWire) and
Audio = .aiff (as on audio-CDs) (else converted to this .aff 48KHz)
Chapters !
A. Using strange letters in video project name eg +,/; etc. keep to a-z and 0-9 strange letters in project name eg +
as described by Donnyboy69. Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
B. Location of Chapters
• Can’t be at start or end of movie (Skip first/start one - iDVD sets this by it self. At the End - no need)
• Not in a transition (or within 2-3 seconds from it)
Important when from iMovie HD6 or previous - Now also observed when using FCE 4
PART Two.
from Robert Modero.
"Multiplexing Error. Problem during initialization of tracks"
Simply remember to add subtitles to your Quicktime files and menu buttons.
Once I did that, I was back in business.
from Boise Jim
Do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
I always makes a DiskImage first and test this so that it runs OK
I use only - Verbatim DVDs
I use only - DVD-R
I burn at an as slow speed possibly eg x1
This gives good DVDs
PART Three.
Multiplex Error
Chuck, Chicago 2/7/2009.
Back again. Here is what I have found to work. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. Apple tech support really didn't know what to do but gave me a very good tip. I had two options left. Apple tech support's tip was to try disc image. One of the replies on a thread with this subject said not to, but my experience today is good. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. So then I tried Utilities> Disc Utility> Burn icon, and followed it through. Be sure to click the DVD DL drive in the window "Burn disc in.". I had one other problem though. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. A long and tortuous process, but at last something works. I made several additional copies using Disc Utility. Best wishes. Chuck, Chicago.
2. Disconnect any other external devices not absolutely needed.
eg external USB/USB2 hard disks, other FW hard disks etc.
3 Chapter marks in transitions - minimum 2 sec from
FROM Bev.
(Not a 'guy' but I will answer!)
First, I do not think that mixing widescreen and standard makes a difference in iDVD.
Second, you should use a better brand of DVD disk. Also, many of us have experienced fewer problems on playback with DVD-R disks. Recommended brands here are Verbatim, Maxell and Taio Yuden. Memorex and TDK are not consistent and may not give you a correct burn. They apparently have fewer layers in the composition of the disk. I have always used Verbatim DVD-R disks and have not had any burn problems.
Also, choose a slower burn speed, 4x or less.
Third, to determine if the iDVD project will burn properly, create a disk image file (from within iDVD, go File->Save as Disk Image) and test it. Mount the disk image and then open DVD Player (in Applications) and view your project. If it plays correctly, you can then burn the actual DVD disk from the disk image file using Disk Utility.
From. Boise, Idaho
I did everything I've seen suggested, but a friend (who used to be an Apple Genius) suggested that I do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
It worked, and I got a clean burn from iDVD.
Hopefully this can help other people.
by dheb0422
Well, I finally got it, and it was odd enough to post here incase anyone looks this topic up again. Many things were tried, including burning the unedited film, the edited film without titles and chapter markers, abbreviating the chapter markers in case length was the issue (remember the old iMovie used to truncate them when moving to iDVD?). In the process, I noticed that one, and only one, chapter marker was on the same line as the title marker. All the others were on the line above. The only way I seemed able to change that was to clip a few seconds of film. After that last clip, the offending marker took a place on the line above, as were all the others. That run published, compiled completely and burned. That's one for the books.
One user more writes
To add my experience with Multiplex Errors using iDVD (7.0.4), I recently created two iDVD projects
Video from both passed from FCE 4.01 with chapters
One project worked fine in creating disk image file
The other gave Multiplex Errors
I tried suggestions to remove special characters and no chapter marks at beginning, but nothing worked
Note that I've used iDVD for dozens of projects and this is first time I've run into Multiplex Errors
Anyway, for problem project, I tried an experiment where I removed all chapters in FCE and passed to new iDVD project
This time multiplex errors gone
So had something to do with chapters
So now I tried numerous experiments to remove individual chapters and try again creating disk image with new iDVD project
After numerous tries, I was able to narrow problem down to 1 "Bad" chapter mark
That is, when I left the "bad" chapter in my FCE project and passed to iDVD, iDVD gave multiplex error
When I removed "bad" chapter mark (and others in), no multiplex error
As a final experiment, I moved "bad" chapter mark about 5-10 secs beyond original point and passed to iDVD, the multiplex errors now magically went away and I was able to finally create my disk image.
I have no idea why this worked, but thought I'd mention here in case someone else runs into similar problem.
Rich839
In addition to Bengt's fine advice, burning errors can occur if you have located any of your menu buttons wholly or partly outside of the safe TV viewing area. Go to your main project menu, then click on View/Show TV Safe Area, to check. Drag into the safe viewing area any buttons that are outside the safe viewing area.
Russ One - suggest this
Multiplex Error-There was an error during muxing preparation
One thing that worked for me was to export the video w/o chapter markers as a self contained movie (thereby not loosing the edits & etc). Then make a new FCE project and import that movie into a new sequence and add the chapter markers. I've used "-", "&" and "," with no problem in the chapter names. Removing the markers or exporting without them did solve the problem but renaming them with just numbers 1,2,3....5, did not solve the problem and since this problem seems to happen with with iMovie as well, it would suggest the problem is in the video or audio and in combination with the chapter markers iDVD just can't handle it. The only other possibility is that both iMovie and FCE share the same or similar chapter marker code that some how is corrupting the markers.
Summary - What to try
1. Chapters
• Only A to Z and 0 to 9 in chapter title
• No Chapter mark at very beginning of movie
• No Chapter mark in or within 2 seconds from any transition in movie
2. TV-safe area for buttons (no one outside this)
3. Safe re-boot
4. No other external devices connected - that are not needed
SDMacuser adds to this
• On #4 ... No ext. devices. Some think this applies mainly to ext. FW. Not the case. Also applies to ext. USB2 as well (not to mention flash drives too).
Do not leave 3rd party devices / camera / camcorder plugged in unless it is being used with iDvd's One Step process. Certain web cams can trigger this also (especially ones with added features like LED light/s that draw additional power from the FW or USB bus).
5. Minimum of 25Gb free space on Start-up hard disk
6. Make a DiskImage first - reduces where problem originates
7. Trash iDVD pref file
8. Make a new iDVD project
9. Movies in project with same aspect ratio eg 4x3 or 16x9
10. No other programs/applications running during iDVD process. eg Internet, screen & energy savers
Yours Bengt W

VGA.ini error during reboot?

Similar Messages

Maybe you are looking for