Vga switch causing resolution problems

Hi, I recently bought a VGA switch by MayFlash so that i could share my 22" widescreen LG monitor with both my x360 and my mac mini. The problem I have is that when i was running my mac mini directly into the monitor via vga cable (with a built in DVI adaptor) the display was instantly recongnised by my mac and displayed at the correct 1680x1050 resolution. However, now im running it through the switch im having all sorts of res problems, firstly the mac doesnt seem to be able to detect the monitor anymore and i have a massive list of resolutions to choose from none of which go up to 1680x1050. All of the resolutions are unsuitable as they are lower res and crop / stretch the screen image. The manufacturer of the switch claim there should be no loss of signal and i've tried upgrading the vga cables im using to superior quality ones to no avail, any ideas?

Likely the easiest thing to do will be to use SwitchRes X to restore 1680 x 1050 as a choice within Displays preferences.
http://www.madrau.com

Similar Messages

VGA cable extension causing resolution problems

Pavilion 6507c with HP 2010i monitor, Windows 7 64-bit. I am trying to separate the CPU and monitor by a few feet more than the original 6' VGA cable allows. Have tried an extension plus original, and also a single longer cable. With anything but the short original cable, the computer no longer recognizes the monitor - it shows it as Generic non-PnP, and will not allow 1600:900, so the picture is stretched. Re-installed 2010i drivers - still comes up generic.
Is there any way to extend the monitor distance without sacrificing proper resolution?
This question was solved.
View Solution.

I wouldn't be too concerned about receiving a no signal message when shutting the PC down. With a longer cable, the signal may degrade sooner causing the no signal message to appear during the shutdown process.
Displays work by the monitor sending the EDID information to the PC and this is part of how the PC identifies what resolutions are available to this monitor. The original cable is allowing this information to be sent from the monitor back to the PC. The PC then retains this information which is what allows it to work with the longer cable after swapping out the 6' VGA cable for a longer or extended one. Once the system is shutdown, the EDID information is lost. This is why it doesn't work once the system is shutdown and started with an extended or long cable.
You did mention an important difference between the cables: the lack of a ferrite core. This Wikipedia entry discusses ferrite beads (aka: ferrite core) and what use they have. Essentially, it reduces the level of interference which could cause the EDID information to be lost before reaching the PC. This is more noticeable when using a long cable, so this could be due to the lack of the ferrite core. However, the adapter listed in my previous post should rectify the resolution issue (though, it would still be listed as a generic PnP monitor).
I would weigh the cost of a cable with the ferrite core against the cost of getting an EDID emulator and select the cheaper option. I know an EDID emulator will rectify this issue, but I cannot say that getting a cable with the ferrite core will correct this issue with 100% certainty. I do know not having a ferrite core can cause signal quality issues. If you can still exchange the cables, then that may be the cheaper option.
Let me know what happens.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

New Posts All Forums:Forum Nav: samsung-hp-r4252 vga macbook connection resolution problem

Hi
I've been trying to connect my 2009 white macbook to my samsung-hp-r4252 42 inch through VGA using the miniDVI to VGA converter. Most of the time I get these two resolutions (see picture) -- which are stretched wide on my tv. However, at seemingly random times I get a whole range of differ resolutions high as around 1900x1200. i've tried a different cable, turning the tv on before the macbook/ vise-versa and everything else i could think of, but can't get the wider list of resolutions to appear. One thing to note is that usually, the external display is shown as Samsung PDP, but when i get a wider list of resolutions it's shown as VGA display. Am I just using a faulty cable or is the problem deeper then that?
Any help would really be appreciated

Hi
I've been trying to connect my 2009 white macbook to my samsung-hp-r4252 42 inch through VGA using the miniDVI to VGA converter. Most of the time I get these two resolutions (see picture) -- which are stretched wide on my tv. However, at seemingly random times I get a whole range of differ resolutions high as around 1900x1200. i've tried a different cable, turning the tv on before the macbook/ vise-versa and everything else i could think of, but can't get the wider list of resolutions to appear. One thing to note is that usually, the external display is shown as Samsung PDP, but when i get a wider list of resolutions it's shown as VGA display. Am I just using a faulty cable or is the problem deeper then that?
Any help would really be appreciated

Can switching from CRT to LCD monitors cause system problems?

My 9.1 locks up periodically (but the cursor still moves) since I replaced two 20" CRT monitors with two Samsung 19" LCD monitors. Could this affect the performance of my machine? I've tried everything else to address the freeze problem but recall the issue started when I installed the LCD monitors. Anything I can do?

Studedot,
You may have issues with the amount of video memory depending on the resolutions of the new LCD screens.
I find LCD screens go up to insane resolutions, way more than the corresponding size CRT monitor, ie. a 17in Dell LCD monitor with higher resolution than a 21in CRT.
It shouldn't cause crashes or freezes, but may cause -redraw problems when closing / moving windows in 2D and playing 3D games.

Dual Monitor Causing System Problems?

Hi, I'm new to this site, so I hope this is where I ask this question! My design group switched to G5/Cinema Display screen from old g4 setups mid 2005. I retained my Mitsubishi Diamond Pro 2020u monitor to use as a secondary display for pallettes, extra files, etc. It's hooked up using a dvi-vga adapter.
My new G5 had hiccups from the start, but around March 2006 I started getting Kernel Panics almost every week, serious slow-downs, Adobe app crashes, etc. It got to the point that I was troubleshooting every week, but could never put a finger on exactly what was happening. IT archive-installed 10.4.4 after we discovered the system had been updated to 10.4.6 and we thought that would solve the problem. While that solved the issues that were relevant to 10.4.6 glitches, it didn't fix everything and little, persistent problems remained, including stalls, crashes and kernel panics. After removing suspect fonts, wallpaper, icons, updating software, repairing permissions, tossing preferences, and other troubleshooting over and over, we (I.T.) finally switched my cpu to another one in the department using data migration (just my user information, not software or other files). Still the same hiccups and even new glitches appeared (InDesign crashing on spellcheck, Photoshop not granting me access to save changes to files, etc.), including two more Kernel panics (within 5 minutes of each other) in the two weeks since we switched hardware. More troubleshooting fixed the app-specific problems, but there are still the persistent annoyances occurring.
I again did all the troubleshooting mentioned above and finally someone mentioned that I'm the only designer in our group using a dual display set-up. Could there be validity to the non-cinema display monitor causing these problems and if so, what is the solution? I've disconnected the second monitor for now, but would love to have it back. Also, we work with a server (for instance, the kernel panics only happen when I try to place a file from the server into InDesign CS2 using the place command, so there's another avenue to go down if the monitor isn't the issue.)Thanks!
G5 Mac OS X (10.4.4) graphic design applications
G5 Mac OS X (10.4.4) graphic design applications
G5 Mac OS X (10.4.4) graphic design applications

I only just disconnected the monitor, so it will take time to tell if that's a factor. As for the kernel panics, although it's always the same scenario (placing images from server through InDesign) they happen very randomly; it's not happening every single time I place a file. In fact, I just placed an image on the server into an ID doc I have on my desktop, no problem. So I can't say for sure that it has happened when working from my desktop or only when working on the server.
G5 Mac OS X (10.4.4) graphic design applications

Using a vga switch

Hi All
I need to switch between two MacBooks while running Keynote on one, and Pages on the other so that I can put up comments live during the talk back part of a session. I am told that it is not possible to edit slides 'live' so this was suggested as the next best thing to do.
Now the problem...
When I switch the 'VGA switch box' the (keynote) macbook reverts to running the Keynote full screen on it's own screen, and the (pages) macbook looks for the projector, finds it , tries several resolutions and after a few seconds decides what to use, settles down and shows Pages. When I switch back to have the Keynote back on screen, the (keynote) macbook does the same, flash a picture up/change resolution/go to black, several times until it finds one it likes and then it stops flashing and shows the slide properly.
I have found a way around this by using a splitter and monitor on each macbook but what I want to find is how to lock the video output to stay on, even if it thinks that the projector has gone away.
Any help gratefully received, Thanks in advance,
David

macdaddy429 wrote:
I want to connect a Mac Mini and a PC to a VGA monitor using a KVM switch. I used a VGA/Mini-display port adapter to connect the switch to the thunderbolt port on the Mac Mini. The PC side works fine, but the monitor says "No Signal" when I switch to the Mini. Thoughts??
My experience of using Macs with KVM devices is that you need to boot the Mac while the KVM is set to display that Mac. This allows the Mac to detect the monitor and correctly set the video card to the right settings.
If you boot the Mac or more typically reboot the Mac while the KVM is set to a different computer the Mac does not see what monitor is connected and then defaults to a settings that will not match the monitor. I find this happens when I am remote controlling a Mac connected to a KVM to for example run an Apple software update which requires a reboot. Being that I am remote to the machine I cannot switch the KVM back to the Mac.
If you do have a Mac that has booted without the KVM being set to it and hence ends up with the wrong video settings, you can consider the following two options.
1. From another Mac use Screen Sharing to control the problem Mac and then try telling it to 'Detect Displays' or if you know the precise video settings, selecting them in Displays.
2. Not applicable to VGA scenarios, but if your using DVI or HDMI, there is a device made specifically for this situation by Gefen. It 'learns' the video settings of the monitor/TV and stores them, it will then keep sending the signal for that monitor/TV to the Mac even if you unplug the monitor/TV completely. These are more often used in home media center setups with AV Receivers (which sort of act as a video switchbox). See http://www.gefen.com/kvm/dproduct.jsp?prod_id=4715 for the DVI version, and http://www.gefen.com/kvm/dproduct.jsp?prod_id=8005 for the HDMI version.

Does dvi to vga adapter change resolution

I had this hooked up to my tv and watched video from had drive. I shut down computer one evening, the next day turned i on, and picture is blurred, and can't see anything---maybe a resolution problem but can't see to change it. bought a new adapter, same thing. I hooked up to another tv, without vga adapter and seems to be fine, hookeed back up to tv with vga adapter, still no picture.

Hello,
Safe Boot from the HD, (holding Shift key down at bootup), see if you can set a good rez there.

Xorg nvidia resolution problems with KDE

I just installed Arch 2008.04-RC last night. I configured xorg.conf using nvidia with the screen resolution set to "1440x900" which worked in both the X Windows and KDE 3.5.9.
I was trying to get xine working with Amarok. At one point, I deleted ~/.xine and xinirtc to force itself to reset. I then rebooted at which point I noticed the resolution set only at "640x400" in KDE. I checked the Display Settings and that was the maximum resolution I could choose. I then switched to the vesa drivers which allowed a maximum resolution of "1024x768".
I removed xorg and nvidia and reinstalled. I can no longer get a resolution of "1440x900" resolution for my Viewsonic VA1926v flat screen monitor. I read on the xorg log that
I am using the Nvidia GeForce 7300 GT video graphics card. uname -r: 2.6.25-ARCH
From /var/log/Xorg.0.log I get the following information when I am using vesa:
(II) VESA(0): Total Memory: 4096 64KB banks (262144kB)
(II) VESA(0): Generic Monitor: Using hsync range of 30.00-82.00 kHz
(II) VESA(0): Generic Monitor: Using vrefresh range of 50.00-75.00 Hz
(II) VESA(0): Not using mode "1440x900" (no mode of this name)
(II) VESA(0): Not using mode "1280x1024" (no mode of this name)
(--) VESA(0): Virtual size is 1024x768 (pitch 1024)
(**) VESA(0): *Built-in mode "1024x768"
(**) VESA(0): *Built-in mode "800x600"
(**) VESA(0): Built-in mode "640x480"
(**) VESA(0): Built-in mode "640x400"
(**) VESA(0): Built-in mode "320x400"
(**) VESA(0): Built-in mode "320x240"
(**) VESA(0): Built-in mode "320x200"
(==) VESA(0): DPI set to (96, 96)
With nvidia, it just states that no mode is available for '1440x900' and selects virtual size of '640x400'.
My xorg.conf below:
Section "ServerLayout"
Identifier "Default Layout"
screen "Default Screen" 0 0
Inputdevice "Generic Keyboard"
Inputdevice "Configured Mouse"
EndSection
Section "Files"
EndSection
Section "Module"
Load "glx"
EndSection
Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/input/mice"
Option "Protocol" "ImPS/2"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "true"
EndSection
Section "Monitor"
Identifier "Generic Monitor"
Horizsync 30.0 - 82.0
Vertrefresh 50.0 - 75.0
Option "DPMS"
EndSection
Section "Device"
Identifier "nVidia Corporation G70 [GeForce 7300 GT]"
Driver "vesa"
Option "AddARGBVisuals" "True"
Option "AddARGBGLXVisuals" "True"
Option "NoLogo" "True"
EndSection
Section "Screen"
Identifier "Default Screen"
Device "nVidia Corporation G70 [GeForce 7300 GT]"
Monitor "Generic Monitor"
Defaultdepth 24
Option "AddARGBVisuals" "True"
Option "NoLogo" "True"
Option "AddARGBGLXVisuals" "True"
Option "UseEdidDpi" "false"
Option "DPI" "96 x 96"
Option "ConnectedMonitor" "DFP"
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1440x900" "1280x1024" "1024x768" "800x600"
EndSubSection
EndSection
Section "Extensions"
Option "Composite" "Enable"
EndSection
I am at a loss at trying to fix this one. Something similar happened when I was running Gentoo on this same desktop back in April. I also have the same low resolution problem when using Sabayon.
Any help here would be much appreciated :-)

I thought these frequencies were a bit low too. My manual said there were the frequencies. I checked online and it said the same. I need to do more research on it.
I did manage to get my 1440x900 resolution back using the open source nv drivers. I had to do the same with Gentoo and Linux Mint in the past. Everytime I used the nvidia drivers, my monitor returns to the 640x400 resolution and I noticed the only way to avoid it was to use nv. I do not play games online or use Compiz so it does not bother me.
Thanks.

DRM Error 3321 Causes & Resolution

[ Problem Background ]
Adobe Access DRM needs to download a device-specific key before protected content can be consumed. This step is called individualization. If user is getting error code 3321 it means the individualization step failed.
[ Root Cause ]
The client needs to make network connection to http://individualization.adobe.com in order to individualize. The failure most likely was caused by a temporary network connection failure. To verify: use the browser and connect to http://individualization.adobe.com/flashaccess/i15n/v5 . View the page source. If everything is fine you will see something like:
<html>
<head>
</head>
<body>

</body>
</html>
[ Resolution ]
Make sure the network connection is fine. Pay special attention to any proxies and firewalls which may be in place.
Also, you may add additional logic to your video application to determine if it is able to query the URL endpoing for individualization in the event handler for 3321. If the connection isn't possible, display a dialog to the end user to check for network connectivity issues (to http://individualization.adobe.com) - perhaps they are behind a firewall or in a network that restricts access to the individualization server.
[ Problem Not Resolved? ]
This article details what Adobe believes will resolve 3321 errors. If this hasn't resolved your issue, we would love to hear more from you! Please reply below with the following information:
- If you don't see the <html> code that is shown above, what are you seeing? Please cut & paste.
- Date & time that you noticed this outage
- OS & OS version of the affected computer
- Browser & browser version of the affected computer

I have recently begun having this problem with:
Firefox (32.0.3)
flash (15.0.0.152)
windows 7 pro 64 bit (Version 6.1.7601 Service Pack 1 Build 7601)
(works fine in Chrome (37.0.2062.124) btw)
I have tried uninstalling/reinstalling both flash and firefox a number of times.
I've deleted my firefox profile, and recreated.
I've deleted %appdata%\adobe\flash player\
I've deleted %appdata%\macromedia\flash player\
I deauthorized the computer
Here is my log from the test defined here: Re: DRM Error 3321 Causes & Resolution
http://drmtest2.adobe.com:8080/AccessPlayer/player.html
12:07:41.363 : DRMError event received
Error Code = 3313 [WriteMicrosafeFailed]
Sub Error Code = 1000055
Error Details =
drmUpdateNeeded = false
systemUpdateNeeded = false
12:07:39.504 : Acquiring License
12:07:35.467 : Metadata received
12:07:35.418 : loading metadata from metadata file...
12:07:31.758 : Player mode changed to TVP
12:07:28.186 : DRM Error: 3313 [WriteMicrosafeFailed]
12:07:24.277 : Load http://drmtest2.adobe.com:8080/Content/anonymous.f4v
12:07:07.056 : This swf version is 20
12:07:07.056 : Player Initialized!
12:07:07.049 : Player mode changed to SVP
12:07:06.938 : Can't access local storage: Error #2134
When I change the amount of "local storage" that the flash player can have, it won't "stick". I go back and it is still at 0.
I've added drmtest2.adobe.com to my global list of allowed sites, and that doesn't help.
A screen shot of the permissions for %appdata%\adobe\flash player\
A screen shot of the permissions for %appdata%\macromedia\flash player\
The global storage settings:
Tried adding drmtest2.adobe.com specifically (still didn't help)
I change this to something > 0, click close, re-open it and it is still 0.
I use AVG AnitVirus Free Edition 2014 (2014.0.4765), I've tried disabling it, to no avail.
This is the error I get:
DRM AUTHORIZATION ERROR
Write to the file system failed.
(Error Code: 3313. Suberror Code: 1000055)

Can MDAC installation cause navigation problems within the portal?

Hello,
I have a client who having problems loading page links in our second level navigation. Evertime time she clicks on node to expand the tree of links, she gets a "loading" message. I see this all the time but this message doesn't go away. She also gets a javascript error on the page stating it cannot find the specify module. She notice the problem around the time of her MDAC file installation. Do anyone know if this can cause a problem for navigation on the portal?
Thank you,
Francis

You made this bed by over complicating your site. Simple solution, take your pages out of sub-folders. Nobody but you cares about the .html extensions. IMO, it's a very poor reason for using sub-folders.
About linking & navigation:
http://help.adobe.com/en_US/dreamweaver/cs/using/WScbb6b82af5544594822510a94ae8d65-7c44a.h tml
Presently, you must be using document relative link paths. Either switch to Site Root Relative links which will likely work on your remote server but fail to test locally. Or use absolute URLs (http://). The downside with this is that DW won't be able to manage links for you.
Nancy O.

Airplay screen mirroring on 4:3 projector, resolution problems.

Hi!
I have an iPad 3, an ATV3 and a NEC NP400 projector which I'm trying to get to work together. I'm not sure about the projectors resolution, but i know it has a 4:3 aspect ratio.
I've tried to use screen mirroring with both the ATV 3 and a VGA adapter, and the problem is that I get black bars on each side no matter which method I use. I understand that the iPad 3 has a 4:3 aspect ratio and that black bars would appear with a 16:9 screen, but not on a 4:3 screen which is the ipads native aspect ratio.
It feels as if the iPad by defalut assumes that I'm having a 16:9 projector and adjust the aspect ratio to that fact. Is there anyway to tell the iPad that i'm having a 4:3 projector? Or should it detect that automatically?
The ATV fills the whole screen without black bars on each side, but as soon as I'm turning screen mirroring on via airplay the aspect ratio changes. There is no difference if I'm using the ATV or the VGA adapter.
How does these things work, and is there a solution?`
Thanks!

Hi!
I have an iPad 3, an ATV3 and a NEC NP400 projector which I'm trying to get to work together. I'm not sure about the projectors resolution, but i know it has a 4:3 aspect ratio.
I've tried to use screen mirroring with both the ATV 3 and a VGA adapter, and the problem is that I get black bars on each side no matter which method I use. I understand that the iPad 3 has a 4:3 aspect ratio and that black bars would appear with a 16:9 screen, but not on a 4:3 screen which is the ipads native aspect ratio.
It feels as if the iPad by defalut assumes that I'm having a 16:9 projector and adjust the aspect ratio to that fact. Is there anyway to tell the iPad that i'm having a 4:3 projector? Or should it detect that automatically?
The ATV fills the whole screen without black bars on each side, but as soon as I'm turning screen mirroring on via airplay the aspect ratio changes. There is no difference if I'm using the ATV or the VGA adapter.
How does these things work, and is there a solution?`
Thanks!

I use the SCC mediaserver in my work, and the crop function has stopped working on Firefox, although it works on Internet Explorer, and I'm wondering if a recent upgrade caused that problem.

I am a newspaper copy editor and use Firefox to work from home. I use the SCC mediaserver to crop photos and place them in the JazBox system, which includes Adobe InCopy and InDesign. For some reason, the crop function is not working on the SCC when I go on it in Firefox, although it's working in Internet Explorer, which is much slower. I didn't have this problem until I installed a Firefox update today. What can I do?

Try to update to Firefox 8.0.1
You can find the latest Firefox release here:
*Firefox 8.0.x: http://www.mozilla.com/en-US/firefox/all.html
Clear the cache and the cookies from sites that cause problems.
"Clear the Cache":
* Tools > Options > Advanced > Network > Offline Storage (Cache): "Clear Now"
"Remove Cookies" from sites causing problems:
* Tools > Options > Privacy > Cookies: "Show Cookies"
Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
*Don't make any changes on the Safe mode start window.
*https://support.mozilla.com/kb/Safe+Mode

My mac mini late 2012 is having resolution problems?

My mac mini late 2012 is having resolution problems?
Tried resetting PRAM and SMC but still nothing works.
Sometimes is goes back to normal. But then suddenly when I startup or wake up from sleep it changes to resolution 800x600 and stays there..
I'm using my Thunderbolt port with my minidisplay port to vga, because i don't have a HD monitor.
Does anyone have a solution?

Hmmm, not sure on the startup, but on the sleep angle...
Well first...
Bootup holding CMD+r, or the Option/alt key to boot from the Restore partition & use Disk Utility from there to Repair the Disk, then Repair Permissions.
Then maybe...
See if it's related to this...
The 2012 macs (and later apparently) not waking normally from sleep after hours being in sleep. (noted here ...
http://www.xlr8yourmac.com/archives/feb13/022813.html#2012macswontwake
"Why 2012 iMac/2012 Mac Mini won't Wake After Hours of Sleep (Hibernates/Powers Off)")
The sleepimage file still reappears even if never slept. Delete it (hibernate off, etc) - within minutes its back.
A note on that here - http://www.xlr8yourmac.com/feedback/Chameleon_SSD_Optimizer.html
About iMac sleep...
http://forums.macrumors.com/showthread.php?t=1529750
Try this: "sudo pmset autopoweroff 0" and "sudo pmset standby 0"

Flash player causes real problems on Youtube

Flash player causes real problems on Youtube site.
I don't really know if it's a Flash Player problem or a Youtube one but Youtube used to work fine back in like 3-4 months ago, now it doesn't anymore.
The issues I encounter with Flash player on Youtube are as follows:
First issue is the fact that after the video completely loads or it loads a big part of it then I click on the seek bar to jump at a specific time that has been already downloaded by the Flash player the video starts loading again from that point on like it didn't actually downloaded that part before. This issue causes big bandwith use since it downloads many many times the same portions of the clip that it has already loaded before dozens of time. If I play a 3 min music clip and click replay or point on the seek bar at the begining of the clip to play it again it loads/downloads the clip again and again and again. If the video clip has over 1 hour then I click play it might entirely load into the player in a few minutes then I click on the seek bar to skip at a certain point it starts loading again from that point on. This is the most anoying thing I encounter with Youtube lately.
Second issue is the fact that if I click on the seek bar of the player to skip to a specific time most of the time the playback does not start from that point on but it skips back to the last point where it was so I must click several times or keep the mouse button pressed for a long time on the same point in order to play from that place on. This one is again very anoying.
Third issue is that after the video starts playing in 360p it automatically changes to 720p after a minute or so even if I had checked this setting "I have a slow connection. Never play higher-quality video" in Youtube Playback Settings. I cleared the cookies and chosed several times the same "I have a slow connection. Never play higher-quality video" setting in Youtube Playback Settings but it just doesn't keep the settings on. This one is again very anoying since my computer can't handle well 720p.
I have reinstalled Win XP SP3 and even installed Win 7 SP1 tried several versions of Flash Player and several versions of Firefox, Chrome and Opera but the same issues occur everytime.
I haven't encounter any of these issues before like 3-4 months ago.

I have had problems trying to watch videos on youtube for the past couple of years. It's been almost unbearable, even if I set the resolution to 144kb! Then a few days ago, I went to youtube and couldn't watch at all. There was an error showing that my Flashplayer was out of date, and then a link to Firefox to get the right update. I did that two times to no avail. I had just installed the newest version of Flash Player as of November 2014, yet this error kept popping up. Finally, out of utter frustration, I did like you did, and uninstalled everything related to Adobe Flash. Then I went to youtube, just to see how bad the result would be, and suddenly videos started playing smoother, at higher resolution, and with faster buffering to start out. Sure, there are some videos that I can't play, and the newest iTunes seemed to have issues without having Flash, but videos aren't frustrating me like they had been on youtube.
So, yeah, I know what you're saying. I had the same solution work for me. Cheers.

XSD Resolution problem - Unable to load Translation schemas

Hi,
I've run into a very strange kind of problem (not to say some are less strange then others). Let me explain the context of the situation.
I've got a BPEL process calling two plsql packages on ORA database, one Java web service running on the same weblogic server and couple of other services (eg. notification services, jdbc select/insert, etc.). There is no problem with the last listed, but definitely something wrong with the web service and the plsql callouts.
When I deploy the BPEL process and execute it, the first two instances always fail. The same happens when I restart the server, the errors are repeated after a certain period as well (for example over night). The process always fails EXACTLY TWICE, before running normally. Every other instance executed after the two initial failures runs WITHOUT the following error.
I mentioned there are two plsql callouts in the process, earlier the first instance failed on the second one and the second instance failed on the first. Now, it mostly fails on the second callout. I've made no significant changes in the code. Perhaps the strangest thing about this is that it fails when invoking the plsql package but the error concerns xsd definitions of the web service that plays no role at this stage.
All my services are correctly deployed, I deleted all interface definitions from MDS repository and redeployed SOA bundle again before installing each service.
I think it has something to do with generated xsd definitions by the java web service (it's the http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 and http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=2 from following stack trace), but I can't figure out what exactly is wrong with them.
Anybody come accross a similar error? Thanks for tips, I've run out of ideas.
Error Message: {http://schemas.oracle.com/bpel/extension}bindingFault
Fault ID     default/S50001KontrolaSouboruBS!1.0*soa_be986963-f9d9-412d-b692-43804a35b3ee/KontrolaSouboru/830023-BpInv18-BpSeq8.12-2
Fault Time     14-Feb-2012 11:11:16
Non Recoverable System Fault :
<bpelFault><faultType>0</faultType><bindingFault xmlns="http://schemas.oracle.com/bpel/extension"><part name="summary"><summary>Exception occured when binding was invoked. Exception occured during invocation of JCA binding: "JCA Binding execute of Reference operation 'LogFile' failed due to: Exception occured when binding was invoked. Exception occured during invocation of JCA binding: "Could not instantiate InteractionSpec oracle.tip.adapter.db.DBStoredProcedureInteractionSpec due to: XSD Resolution problem. XSD Resolution problem. Unable to load Translation schemas from for http://xmlns.oracle.com/pcbpel/adapter/db/TST_IP/LOG_FILE/LOG_FILE/ due to: Different schema default values detected between: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=2 and oramds:/apps/LCRInterface/DataObjects/Common/V1/Common.xsd elementFormDefault values are differentDifferent schema default values detected between: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=2 and http://localhost:8001/soa-infra/services/default/S50035NotifikaceChybyBS/apps/LCRInterface/DataObjects/Common/V1/Common.xsd elementFormDefault values are differentDifferent schema default values detected between: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=2 and oramds:/apps/LCRInterface/DataObjects/Common/V1/DataTypes.xsd elementFormDefault values are differentDifferent schema default values detected between: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=2 and http://localhost:8001/soa-infra/services/default/S50035NotifikaceChybyBS/apps/LCRInterface/DataObjects/Common/V1/DataTypes.xsd elementFormDefault values are differentGlobal element declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetFileListByMaskRespDM' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 7] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 82] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:7] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:82] Global element declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetFileListDM' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 9] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 36] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:9] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:36] Global element declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}SaveFileDM' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 19] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 21] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:19] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:21] Global element declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetFileListRespDM' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 11] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 51] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:11] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:51] Global element declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetFileListByMaskDM' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 5] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 66] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:5] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:66] Global element declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetTextFileDM' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 13] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 112] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:13] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:112] Global element declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetTextFileRespDM' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 15] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 127] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:15] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:127] Global element declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}RenameFileDM' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 17] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 97] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:17] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:97] Global Type declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetFileListRespDataType' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 115] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 52] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:117] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:54] Global Type declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}RenameFileDataType' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 175] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 98] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:177] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:100] Global Type declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetTextFileRespDataType' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 153] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 128] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:155] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:130] Global Type declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetFileListByMaskRespDataType' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 64] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 83] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:66] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:85] Global Type declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}SaveFileDataType' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 93] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 22] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:95] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:24] Please make sure all used XML schemas are imported/included correctly. ". The invoked JCA adapter raised a resource exception. Please examine the above error message carefully to determine a resolution. ". The invoked JCA adapter raised a resource exception. Please examine the above error message carefully to determine a resolution. </summary></part><part name="detail"><detail>Different schema default values detected between: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=2 and oramds:/apps/LCRInterface/DataObjects/Common/V1/Common.xsd elementFormDefault values are differentDifferent schema default values detected between: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=2 and http://localhost:8001/soa-infra/services/default/S50035NotifikaceChybyBS/apps/LCRInterface/DataObjects/Common/V1/Common.xsd elementFormDefault values are differentDifferent schema default values detected between: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=2 and oramds:/apps/LCRInterface/DataObjects/Common/V1/DataTypes.xsd elementFormDefault values are differentDifferent schema default values detected between: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=2 and http://localhost:8001/soa-infra/services/default/S50035NotifikaceChybyBS/apps/LCRInterface/DataObjects/Common/V1/DataTypes.xsd elementFormDefault values are differentGlobal element declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetFileListByMaskRespDM' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 7] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 82] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:7] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:82] Global element declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetFileListDM' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 9] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 36] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:9] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:36] Global element declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}SaveFileDM' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 19] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 21] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:19] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:21] Global element declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetFileListRespDM' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 11] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 51] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:11] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:51] Global element declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetFileListByMaskDM' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 5] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 66] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:5] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:66] Global element declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetTextFileDM' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 13] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 112] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:13] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:112] Global element declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetTextFileRespDM' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 15] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 127] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:15] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:127] Global element declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}RenameFileDM' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 17] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 97] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:17] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:97] Global Type declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetFileListRespDataType' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 115] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 52] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:117] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:54] Global Type declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}RenameFileDataType' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 175] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 98] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:177] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:100] Global Type declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetTextFileRespDataType' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 153] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 128] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:155] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:130] Global Type declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}GetFileListByMaskRespDataType' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 64] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 83] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:66] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:85] Global Type declaration/definition of name '{http://xmlns.lesycr.cz/DO/PrenosSouboru/V1}SaveFileDataType' are duplicated at the following locations: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [line#: 93] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [line#: 22] There are at least two of them looking different: http://localhost:8001/S50040PrenosSouboruBS/PrenosSouboruBSSOAP11BindingPort?xsd=1 [difference starting at line#:95] oramds:/apps/LCRInterface/DataObjects/D500Proces/PrenosSouboru/V1/PrenosSouboruDM.xsd [difference starting at line#:24] </detail></part><part name="code"><code>null</code></part></bindingFault></bpelFault>

I had similar issue, when i deployed composite using Jdeveloper. The problem was with my adf-config.xml pointing to dev server and all my references in my composite.xml referring to test server.
I changed property of 'oracle.mds.persistence.stores.db.DBMetadataStore' in adf-config.xml to test server. After adf-config.xml change in Jdev my compilation went smooth.
Note: If above changes doesn't work, try restarting JDeveloper, sometimes the changes in adf-config.xml is not getting effect immediately.
Regards,
Ziaur Rahuman S
Edited by: Ziaur Rahuman on Feb 13, 2013 10:58 PM

Vga switch causing resolution problems

Similar Messages

Maybe you are looking for