VI Logger: digital input?

Does the VI Logger software work with digital input, or only analog input?

Hi Zack, you can only measure analog channels, but you can use digital lines as triggers for analog lines
http://digital.ni.com/public.nsf/websearch/86256F0E001DA9FD86256F660071FD6F?OpenDocument
Benjamin C
Senior Systems Engineer // CLA // CLED // CTD

Similar Messages

Usb 6009 digital input

Dear All!!
With the following vi. I'm trying to receive a 5V signal in a digital input, using a usb-6009 device.
I would like to use the 5 VCC supply, available in pin 31 of the same device and send it to pin 17, representing line0 of port0. During execution, 'm physically connecting and disconnecting these pins in order to see the difference in a led indicator. Unfortunatelly, the led is always on, even if both pins are disconnected.
Could somebody help me? I would be very pleased.
Thank you very much in advance,
Miren
Attachments:
proof.vi ‏38 KB

Hi Miren,
"the led is always on, even if both pins are disconnected"
RTFM?!
They use open collector inputs with an internal pullup resistor of 4.7k, so you actively have to pull down the input to GND to see a difference...
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

How to acquire serial data on a digital input line with good performance?

Hello,
we have a performance problem with our realtime controller. Our objective is, to read a 24-bit long digital waveform from a digital input line. To do this, we supply a clock signal (236 KHz) to the PFI1 Line of our DAQ Board. On each rising edge of the clock, a new bit is set on the digital input DI0.
Our hardware which transmits the data, is triggered through a digital output from our realtime controller. On each edge on this output, the hardware starts a serial transmission of 24-Bits.
Everything works fine except the bad performance of our realtime controller. We want to acquire the 24-Bits in a 1ms timed loop. To measure performance we wrote a test program. In that, we only triggered the hardware and transfered the data to the realtime controller. The task which is doing this job, has a approx. CPU-Load of 30%, which is, in my humble opinion, very high. The task is not waiting for data or anything else! We have earlier implemented a control which is also using a 1ms timed loop. This control is sampling 2 analog input signals, 2 counters. Futhermore it's sending telegrams with CAN and doing many calculations. The strange thing is, this much huger program has a CPU-Load of 25%. Does anybody know where the problem is?
For the better understandig I attached our test-program to this text.
We're using:
PXI-8175 realtime controler
PXI-6221 Multifunction DAQ
Thanks!
Regards,
Crest!
Attachments:
dig_test.zip ‏51 KB

Hello,
First of all 30% CPU-Load is normal because the DAQmx-driver needs a lot of resources.
In your programm you should place a wait (for example with 1ms) into the while-loop which causes
lower CPU-Load.
If this is not enough you should build your vi like in the following example.
Regards,
Christian
Attachments:
Read Dig Port.vi ‏51 KB

How can i connect 24VDC to digital input (usb 6008)

hello,
how can i connect 24VDC to digital input (usb 6008), is it possible with some optocoupler?
thanks

The 6008 is a static DIO, so speed shouldn't be an issue. Therefore an optocoupler should work. Just make sure you get one the meets your specs.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

Audigy 4 Pro digital input 16 - 24

I have a Sony MDS-JB920 minidisc deck hooked up to my Audigy 4 Pro through the external box. Works fine.
However, the Minidisc deck allows one to set both the digital input and output to either 6, 20 or 24 bit. As the Audigy 4 Pro is 24 bit, I've set the deck to 24 bit for both in and out. So far no problems. If I watch the settings panel whilst playing a minidisc however, it indicates that the signal coming from the MD deck is 6 bit, although the deck is set to supply 24 bit through the SPDIF out.
When I put the MD deck on rec mode whilst the PC is supplying audio feed, the MD deck loops it back to the SPDIF input of the Audigy and then the software does display 24 bit signal coming from the MD deck.
This is very confusing to me, does anyone have an explanation?

CMSS is an effect used for stereo sounds, to emulate surround sound for them. It has no effect on the DVDs you're playing as you're just outputting the AC3 signal so the speakers can decode it.
If you're using a digital connection, then CMSS will not have any effect for other sound either, you need to connect through multiple analog connections to get that sound. A standard digital connection (coaxial and optical SPDIF) can only pass over either a stereo PCM signal, or an encoded AC3 stream (like on your DVDs). Normal sound like music or games will only be passed over as stereo PCM, so there is no CMSS effect there.
If you can connect your amplifier through several analog connections, then you can use CMSS aswell, otherwise your amplifier might have it's own upmix option like ProLogic.
Cat

How to I connect Sourcing digital output from My Interface Board to NI USB 6501 channel configured as Digital input

When I connect an input to DI channel of USB 6501 card from my board which has sourcing Output t, iIn the Off state it is not pulled down properly. The volatge on the port in is 2.1V -2.5V based on the pull down resistor on my board. I suspect that it acts as a voltage divider.
The state on the card is still show as "HIGH "state, even my sourcing output driver has a pull down resister. when I use this interface board for PCI mseries devices it works fine. Do the pull down resister on my sourcing output is not worth. Is this because of pull up resister 4.7k inside USB card 6501.
USB 6501 specifications shows the Digital input accepts both source and sink modes. By default the card is in sourcing digital input mode. How do we can convert this in Sinkind digital input mode.
Could anyone Please give your suggestions to overcome this issue .
Thanks you.

You really should not have both a pull up and pull down on the same line. Really weird things can happen. If you insist on having a pull down on your board, then I highly recommend putting a digital buffer chip between the DAQ and your board.
Some boards with DIO have a pull up, while others have pull down. You just have to watch the specs.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

I was given an assingment, but have no idea where to begin. The assingment is to create a text file using notepad with all of my digital inputs and some how make those imputs show up on my digital indicators on my control pannel

I was given an assingment, but have no idea where to begin. The assingment is to create a text file using notepad with all of my digital inputs and some how make those imputs show up on my digital indicators on my control pannel.
When it was explained to me it didn't sound to hard of a task, I have no LabVIEW experience and the tutortial sucks.

StevenD: FYI, I did NOT give you the one star rating. I would never do that!
StevenD wrote:
Ow. Someone is grumpy today.
Well, this is an assignment, so it is probably homework.
Why else would anyone give HIM such an assigment, after all he has no LabVIEW experience and the tutorials are too hard for him?
This would make no sense unless all of it was just covered in class!
This is not a free homework service with instant gratification.
OK! Let's do it step by step. I assume you already have a VI with the digital indicators.
"...but have no idea where to begin".
open notepad.
decide on a format, possibly one line per indicator.
type the document.
close notepad.
open LabVIEW.
Open the existing VI with all the indicators.
(are you still following?)
look at the diagram.
Who made the program?
Does the code make sense so far?
Is it a statemachine or just a bunch of crisscrossed wires?
Where do you want to add the file read?
How should the file be read (after pressing a read button, at the start of the program ,etc.)
See how far you get!
Message Edited by altenbach on 06-24-2008 11:23 AM
LabVIEW Champion . Do more with less code and in less time .

Triggering an event with a digital input

Hello all,
I'm writing my first Labview program. I used an architecture I found on the forums here, and it has been very helpful in getting me started. This architecture uses two while loops, one containing an event structure and one containing a case structure. (This is a queued state machine architecture, I believe).
Part way through the programming, we decided we needed a sensor to make sure the part was in the test fixture during the test. If the part is removed during the test, we'd like to safely stop the test. So basically, I need to monitor a digital input (on an NI-USB-6525 module) and enter the "Stop" case if the digital input turns off. I would also like to make sure this digital input is on before entering the "Start" case. I don't care if the input changes state when the test is not running, nor do I care about its state during the "Exit" case.
I'm really not sure how to add this functionality to my "stop" case. I don't even know if it's possible. I've been researching DAQmx events, but I haven't found an example or answer that aligns with my particular problem.
I've attached my code. It's incomplete right now - I still have a large number of steps to add. I wanted to get this issue figured out before I programmed any more steps. A preview of the code showing the basic architecture is shown in the picture below.
Does anyone have any ideas or suggestions for me, or questions if my problem is unclear? Also, if you see anything else in my code that will be problematic, please let me know.
Thanks in advance!
Attachments:
Main_Loop_072412.vi ‏195 KB

I should also add that I looked into event dynamic registration, but it seemed incompatible with my issue. I don't want my top loop to run only when an event triggers it - I want it to run all the time so that it can immediately respond to button presses. Also, most of the triggering I found was based on value change. I care about the actual value, not just that it changed.
I don't want to do anything that will bog the code down too much since it is important that the system respond immediately to inputs, especially to the stop or exit button presses.
I'm sure I am missing something very basic here. I'm used to ladder logic, where everything is simple and straightforward.

Digital Input Cannot Display this Video Mode Optimum Resolution 1280 x 1024 60hz.

HP Pavilion h8-1360t, Windows7 home premium 64-bit, AMD Radeon HD 7570 graphics card.
error message: Digital Input Cannot Display this Video Mode Optimum Resolution 1280 x 1024 60hz.
I get the error message as soon as Windows opens and the desktop displays. Then it goes black with that message. I've been using the computer for awhile and I had it so that when I maximized a window it would go across both screens. I have two monitors on the graphics card. Somehow I changed the settings so that a program would maximize to one monitor or the other. That is how I want it to work. Maybe I activated HydraVision. Now I have the problem when I start.
Also now when I boot to Safe Mode I get the message that there is no AMD graphics driver installed, or it is not functioning properly. I have tried to update it and the computer tells me I have the most recent version installed. I would like to uninstall it and reinstall it, but I'm a little worried I won't get it installed and be without video. Something like that happened to me once before years ago.
Could someone tell me what I should do please?
Thanks,
Jim Allen

HP support is here:
http://www8.hp.com/us/en/contact-hp/contact.html
In safe mode you should uninstall the driver, then try to boot normal again.
Then check if driver was installed by win7.
If not go go AMD website and download latest driver for your card.
V.
*** Say 'Thanks' with Kudos ***

Monitors with Digital Inputs

What monitors are available that accept the Toslink input directly? Do the keyboard and on-screen volume controls still work with this arrangement?

I believe Tannoy make a set of the Elipse range of speaker with digital inputs as well. I have no idea why you would want to do this though. I suspect the gains in quality would be tiny if anything at all. You'd be better to spend more money on something less techy and get something that really sounds great!

How can I use 4 DIO lines as digital input in a E series-SC 2050-ER8 set up ?

I have a DAQ system with an E series DAQ card that is connected to SC-2050 and ER8. I want to use 4 DIO lines (out of 8) for digital input. How can I do this?

Hello Suresh,
There are a variety of ways to accomplish this. If you are using LabVIEW, you will use the DIO Port Config VI and the DIO Port Read VI. You will use the line direction map input of the DIO Port Config VI to setup which 4 lines you want to be the input lines. The LabVIEW shipping example entitled 'Dig Multi-line Direction (E) VI' shows how to use the lines of the digital port on an E-Series device for input and output.
If you are using NI-DAQ function calls, you can use the Dig_Line_Config and Dig_In_Line calls to configure a digital line for input and then read from that line.
I hope this helps.
Regards,
Todd D.
NI Applications Engineer

Can't change sample rate for digital input on Mac Pro

Hello all,
on my Mac Pro with 10.4.10 I can't change the sample rate for the digital input. Whenever I choose 48000 or 96000 Hz it returns to 44100 Hz after a few seconds. Feeding a 24 bit/96000 Hz signal from an external ADC into the optical input doesn't help. No input signal is available for digital recording software such as Sound Studio or Cubase. After changing the sample rate in audio midi configuration to 96000 Hz the sound can be heard for a few seconds but when the setup returns to 44100 automatically the signal is, of course, lost.
I've deleted all relevant preferences and restarted with resetting paramter RAM. Still the same. With external hardware such as M-Audio Firewire equipment setting the sample rates works properly.
Thanks to all for helpful clues.

Hi,
when E&M signaling is configured on digital interface like the VWIC is, 2 or 4 wires operation is not applicable because there are no wires at all, and reported only for compatibility with the analog E&M card.
Consequently, you cannot configure that and it will not make any difference to effect of the connection.
Please rate post if it helps!

Comparing digital input and output from two different DAQs

I want to create this program where the digital output lights up LEDs at random and push buttons are the digital input part of another DAQ are pushed. When the correct button is pushed, the score will increase by 1. My code doesn't work though. Can someone point my errors to me? Both the DAQs i'm using are USB-6008 DAQs. thanks
Attachments:
Untitled 1.vi ‏41 KB

Let's start with the digital output
What is this code all about?
Do you want only one of the 8 led's to lit randomly or are multiple led's also ok?
The two possible codes are in attached file SNAG-003.jpg
Connect the output of the "Scale by power of 2" function or the "Multiply" output directly to the Write DAQmx vi
I don't understand the purpose of the "Boolean Value" and "Replace subset array" thing, so I skipped it
Attachments:
SNAG-002.jpg ‏49 KB
SNAG-003.jpg ‏22 KB

Simultaneous Digital Input and Output from NI 9403

Hi,
I was wondering if it is possible to digital output through one line in this module(NI 9403) while simultaneously reading from 10 other lines?
Basically what I need is for line0 to always be closed(true), and read lines1:10 - at very least 1sample/second.
I have attached a stripped down version of my code illustrating my error. I thought I was getting the error because the two tasks were using different clock configurations, but I tried using the same inputs and that doesn't work for me.
Any input is greatly appreciated.
Thank you
Attachments:
Digital I-O.vi ‏22 KB

Hi Matthew,
The behavior you're seeing is expected for the 9403 module, since it is a serial module. The DAQmx help has the following restrictions in the Digital I/O Considerations for C Series Devices section.
Timed digital input/output restrictions:
You cannot use parallel and serial modules together on the same hardware timed task.
You cannot use serial modules for triggering.
You cannot do both static and timed tasks at the same time on a single serial module.
You can only do hardware timing in one direction at a time on a serial bidirectional module.
So you can only do timed input or output at one time, but not both. However, based on the VI you attached and the description of what you want to do, you don't necessarily need both timed tasks in your loop. You can create a static output task to update that one line and after that, you can just start your timed input task on the rest of the lines. This should maintain the state on the DO line, since you're not acquiring from it.
Cheers,
Cristina
Cristina

How to force digital input sample rate?

Does anyone know how to force a Digital Input sample rate and/or tell Core Audio which conversion clock to use... internal or external? Apparently both things can be done from Pro Tools, but I don't have it. My problem is locking onto an A/D converter's 48K Toslink output. I can set 48K in 'Audio - Midi' setup and the audio is perfect, but a few seconds later Core Audio returns to the default 44.1K. I need to force it to stay at 48K, or clock on the signal rather than internal clock.

Braver,
Let me clarify a few things. First, the 6733 supports correlated digital I/O. This means that the digital operation does not have its own clock. You can correlate the digital operation with the AO clock, which will allow a digital operation up to the max AO rate. You can generate a pulse train with an onboard counter and use that as your digital clock source. Also, you can use a completely external clock source to achieve the max digital rate of 10MHz. The knowledge base, linked below, points you to a couple of examples that ship with LabVIEW. Be sure and read the documentation associated with each example.
Knowlege Base
As for
the example CDI Single Point clocked by Counter (E).vi, notice how the output of...

VI Logger: digital input?

Similar Messages

Maybe you are looking for