[VIA] Just need some input on a problem I have

I need the experts on this forum to help me with a problem I have. The M/B (6590 KT4 Socket A) had a few problems a while see. Since that time I have not updated my PSU as advised  so I expect some abuse for that  .
Any way I managed in the to fix that problem as you can see. However a further problem occured which was that the PC ,at will , would restart - this ended being the reset switch which I disconnected and this has never happened since. Now I have another problem !  .
The PC will simply hang with no response at all.  It seems only to happen when I am running the capture software. I have checked for updates and applied these to the program (hauppauges WnTV). This set up was running on another PC with a M/B (in my opinon) of inferior quality without a problem (I have since sold that PC).
 I will admit I have not run the PC without this program running to see if that is the cause. However I just needed input on suggestions. My PSU is as I said earlier the same as before which is an X Pro 400w these are the shameful Voltage rails :
+5v = 35a
+12v = 20a
-5v = 0.5v
-12v = 0.8v
3.3v = 22a
5+VSB=3a
Also when the PC hung I got the following readings from PCAlert:
1.76 Vcore
3.3v = 3.26v
+5v= 4.97
+12v = 12.24
CPU temp = 44c
System temp = 38c
I must admit that the previous PC had a separate USB2 (which is how the Happauge unit connects) card whereas this PC I use the onboard card. I was also thinking about the RAM as it was one I bought from a computer fair (hears groans) - This is  normally something I do not do.
Help input would be appreciated

Quote from: Dr Stu on 26-November-05, 05:58:45
look on the PSU label for the Max Combined Watts 3.3v & 5v and post what it says
KT4 doesn't have a 4pin 12v connector, right? so that board depends on 3.3v and 5v rails
The Max watts are 210Watts
Quote
While waiting for the experts, three things come to my mind:
- IRQ problem, most often some/the card is in the wrong slot.
- Graphics driver, most often you have updated too far.
- Memory problem, most often mixed, but could also be there are things/drivers meeting in the memory that doesn't like eachother. If you have a lot of Autostarting thing that could be the reason, like a CD copying program and the capture program.
It cannot be an IRQ conflict as the Capture card is USB2. Graphics card has up to date drivers. Startup software on this PC is no different to the preivous apart from PCAlert4
Quote
"...It seems only to happen when I am running the capture software..."  Have you tried another program system intensive demanding ? If you have done, and nothing happens, it would show that the capture device/driver is giving problems. Is that USB device self powered or takes it's power from USB port ? It's running at USB 2.0 speed ? 22 A to 3.3v. rail is poor for your Mobo.  You should post your complete PC specs.
I dont really have any other software than can do that. The USB device is powered by itself.
PC is as follows:
AMD 2100+
1 512mb ram
2 HDD - 1 80gb Hitachi 1 120gb hitachi
Nvidia Geforce mmx 64mb ram Graphics card
1 SCSI CDROM Teac
1 SCSI CDRW Yamaha
1 IDE DVDROM Sony
1 IDE DVDR LG
Quote
Make sure that the pathway to were you want to save the captured video is set correctly. I believe you can set the Audio quality and the Frames Per Second (FPS) and I think that you can set the compression, If in doubt try it without compression and see if that works. I too have a TV card and it seems to me that you are having a config problem. Hope that helps.
The location where the files are captured to is to the secondary drive which is the 120gb
Hope thats enough information 

Similar Messages

  • Hi i just need some pl/sql materials and apps materials

    Hi,
    friends i am krish getting trained on orcale just need some materials to leanr quickly pl/sql
    thnx for the sender
    Thanks & Regards
    krish

    for R12,
    http://download.oracle.com/docs/cd/B40089_08/current/html/docset.html
    And for pl/sql
    http://download-uk.oracle.com/docs/cd/A97630_01/appdev.920/a96624/toc.htm
    Message was edited by:
    Nitesh Jain

  • Hi i need some help im having problems the ipod can not be turned , in fact it was working fine but suddenly switched off and did not return to light n because it reconnected and if I had drums

    hi i need some help im having problems , the ipod can not be turned , in fact it was working fine but suddenly switched off and did not return to light n because it reconnected and if I had drums  . what can i do to turned on .
    its an ipod touch 64gb

    That symptom is covered here:
    iPod touch: Hardware troubleshooting

  • HT1688 I dropped my I Phone 4S last night and it wont do anythig. I just need to set up an appt to have a tech look at it.

    I dropped my I Phone 4S last night and it wont do anythig. I just need to set up an appt to have a tech look at it at the Sugar Land Mall store.
    Thank You
    Dawn Millis

    Find your Apple Store from this list:
    http://www.apple.com/retail/storelist/
    go to the store site and select "genius bar" under "make a reservation". You can make an appointment there.
    Regards.

  • Need some input about a class I'm making.

    Hi guys.
    Take a look at this class:
    public class MyClass {
    public static final byte A_PARAM1 = (byte)0x80;
    public static final byte B_PARAM2 = (byte)0x40;
    public static final byte A_PARAM2 = (byte)0x20;
    public static final byte B_PARAM2 = (byte)0x10;
    public MyClass(byte param1, byte param2) {
    // Other functions go here...
    }As you can see from the code the constructor takes two byte's. I wanted the static variables to be the values for that constructor A/B_PARAM1 and A/B_PARAM2 for param1 and param2 respectively. It depends on the parameters (bytes) on what other behaviour the class will have. You know, A_PARAM1 OR'ed(bitwise) with B_PARAM1. I'm sorry if I'm not making any sense as I'm not that good with explaining things.
    I'm sure that most of you can already see some problems with this approach. For one, typesafety. Is that the correct term for that? Another problem is I'll be making a lot of these classes and each will have a different number of parameters for them. One or two can have as much as 5 parameters.
    One solution I'm thinking about is to have the parameters(mostly just byte's) represented as a class. Maybe an generic abstract class with just simple functions of getting and setting the value. The different subclasses will contain the static variables. I was also thinking that the class that will be using it as values will be the only one that can create the subclasses of the abstract parameter class.
    I don't know. Am I making any sense?
    Anyway. Could anyone give me some input? Am I doing this right or is it just too much that I should just stick with what I'm currently doing? How would you go on with the problem?
    Thanks in advance.

    Hello again. The EnumSet class is making me scratch my head a bit.
    I'd like to return to my initial idea of extending a class that will represent a parameter. Take a look at this:
    public class MutantCarThing {
         public static final byte HAS_EYES = (byte)0x80;
         public static final byte HAS_NOSE = (byte)0x40;
         public static final byte HAS_TEETH = (byte)0x01;
         public static final byte ONE_WHEEL = (byte)0x80;
         public static final byte ONE_DOOR = (byte)0x40;
         public static final byte HAS_WINDSHIELD = (byte)0x01;
         private byte facialFeaturesParam;
         private byte carFeaturesParam;
         public MutantCar(byte facialFeaturesParam, byte partsFeaturesParam) {
              this.facialFeaturesParam = facialFeaturesParam;
              this.partsFeaturesParam = partsFeaturesParam;
              // Stuff
    public class MutantCarMaker {
         public void make() {
              // Mutant car that has only eyes and one wheel.
              MutantCar mc = new MutantCar(MutantCar.HAS_EYES, MutantCar.ONE_WHEEL);
              // Mutant car with a nose, eyes, and only one door.
              MutantCar mc = new MutantCar(MutantCar.HAS_NOSE | MutantCar.HAS_EYES, MutantCar.ONE_DOOR);
              // Etc...
    }This is just an example and as I've said earlier, I'll be writing lots of these classes. The good thing here is that all of them have some common behaviors, both the xxThing and xxMaker class. I'll just make a base abstract class and extend. My only dilemma is the darn parameters (eg. facialFeaturesParam, carFeaturesParam). One xxThing class can have as much 5 parameters(usually as byte) and have a completely different names for the bit flags for each byte. That's why the idea of a Parameter class came to mind. I'm having a hard time grasping EnumSet.
    I guess what I want to do is just to make instantiating a xxMaker object more simple.
    xxMaker xm = new xxMaker(xxMaker.BFLAGA1 | xxMaker.BFLAGA2 | xxMaker.BFLAGA3 | xxMaker.BFLAGA4,
                                  xxMaker.BFLAGB1 | xxMaker.BFLAGB2 | xxMaker.BFLAGB3,
                                  xxMaker.BLFAGC1 | xxMaker.BFLAGC2);Ugly isn't it? I just want to make this more cleaner and more structured.
    So is my idea ok or is it totally off/unnecessary/stupid? How would any of you guys here do it? Or should I really get myself to use EnumSets?
    Edited by: romainechester on Nov 15, 2007 6:28 PM
    Edited by: romainechester on Nov 15, 2007 6:36 PM

  • I have a iphone 4  and when i call people then cant hear me  and the mute is off ..  need some help with this problem

    i have a iphone 4 and when i call people about 70 percent of the time then cant hear me and the mute is not on ,  need some help

    Please see the  More Like This  section on the right.

  • Need some inputs

    hi,
    I have created a web service wherein on submitting the employee name, i can get the balance in the account of the employee.
    my service communicates with database which is an excel sheet. and the client is a servlet which invokes the service.
    hi all,
    I have created a web service wherein on submitting the employee name, i can get the balance in the account of the employee.
    my service communicates with database which is an excel sheet. and the client is a servlet which invokes the service.
    i have used Apache soap implementation for this.
    I have tried this out of my interest and want to get some inputs as where does this application stand.
    Also if anyone can tell me wht can be a real world financial application which i can try making as web service.
    How can i make this available on the net.
    any help would be highly appreciated.
    Thanks and regards
    neha

    Generally webservices are more useful in solving business application in which multiple organizations are involved. Suppose if one organizations creates the services they perform as webservices the other organization can use those services. For example customer order servise, health insurance and all. Better you send a mail to mail id then I can help you more. [email protected]

  • Hello & Need some input - MSI Lightning Extreme 580's

    Hello All-
    In a few days, well as soon as UPS delivers my new toys I will be a new member to the MSI GPU Family.  I have 2 Lightning Extreme 580's on the way and just wanted some feedback/advice on the best way to test/connect the cards.  I currently am running a 2x580 EVGA Vanilla Cards, so I do understand the whole SLI situation.  My questions/help is below:
    1. Since these are 2 new cards, is it advisable to install one at a time and test the card by itself first? Then install the 2nd card seperately and test it?
    2. Obviously anyone buying this card is going to OC it. So it is also advisable to OC one card at a time to test each card and how the OC?
    3. I noticed 2-3 areas where the SLI Cable can connect too.  Does it matter which one you connect the SLI Ribbon too?
    For any owners of the Extreme 580 and advice you would give to a new owner of the card?
    Lastly, is there a site or a chart that shows what others were able to achieve with OC?  I know for my EVGA's there were alot of spreedsheets showing various users and what speed, fan percentage, temps etc. Anything like that for the MSI Family?

    Quote
    1. Since these are 2 new cards, is it advisable to install one at a time and test the card by itself first? Then install the 2nd card seperately and test it?
    2. Obviously anyone buying this card is going to OC it. So it is also advisable to OC one card at a time to test each card and how the OC?
    3. I noticed 2-3 areas where the SLI Cable can connect too.  Does it matter which one you connect the SLI Ribbon too?
    ==> 1. It's not necessary to do this. This can only helps if you have issues and by testing in that ways it can be isolated which card is cause the eventual trouble. As there is no reason to suspect cards failure you can skip this.
    ==> 2. It's also not necessary to do this. Because when they are running in SLI, both combined speed will be equal to the lower card speed in the party.
    So finding personally which one card how much can be overclocked will be useless as the total speed will be speed of the slowest card in the party.
    ect: finding the card with better OC potencial will be useless, as you will run them in SLI and their combined speed will be down to the slowest card.
    ==> 3. Use the 1st one connector near to the VGA's outputs. Etc:

  • Hello,i just need some information

    Hy,i just have some questions...First,i am in project for creating some website with streaming video.The connection to the host is bad and i need to know if Flash media server can reconnect if connection is lost during playback and second,is there some kind of plugin for subtitles,this is very important,If there is a positive answers on those two questions,the third would be "where can i buy it and how"?

    First question: Yes very much. You can write simple logic for reconnection. Also there is new feature called Smart Reconnect which you can use for this purpose.
    Smart Reconnect links: -
    http://help.adobe.com/en_US/FlashMediaServer/3.5.3/FeaturesGuide/flashmediaserver_3.5.3_fe atures.pdf
    http://aspexamples.adobe.com/flash/streamreconnect.html
    Second question: - I am not aware of such plug-in personally but there are high chances that it might be available. But i want to know first how you want to achieve it - are you sub titles not embedded in movie itself or is it separate from movie content and if yes in what format. Even if one is not available for ready to use - i think developing one should not be big deal - it can simple as overlay on your client side which gets populated with text at runtime.
    Third question: You can download it from http://www.adobe.com/products/flashmediaserver/ (just choose your edition & on that page you should have download link) - OR once you decide to buy you can send your contact details(Name,Email,Phone,Geo Location) to me via private message and i can help you get in touch with right person.

  • ASA 5505 unable to access ASDM ( just needs some ports ope and FWDing setup)

    I was able to access the ASDM launcher in the browser yesterday   via    https://192.168.111.1/admin and I was stuck there as the browser version says that my ASA image does not work with my ASDM version...      So i tried some trouble shooting and think that i may have changed the image to an image that does not exist.     (I'm not sure where it is that I would actually place that image either)    Now i am unable to access through the browser at all.
    Anyways, I am ok with SSH/CLI and have been using my firewall in this manner.   I am walking into this companies current configuration and simply need to do the following:
    I need to OPEN ports 9000, 85, 40085, 49005 so that my mobile device can pull my security cameras in the office 
    I need to set port forwarding so that any connections that hit outside-in ip address 205.214.36.53:1610 >>> http://192.168.111.30:1610/AndroidWS/     for our new mobile CRM.
    I have been through some of your related discussions and am falling short somewhere.   Please help
    here is my "show run"  and my "dir"
    ciscoasa(config)# show run
    : Saved
    ASA Version 9.0(2)
    hostname ciscoasa
    domain-name scec.local
    enable password ol40hHpZTtZQFXMJ encrypted
    xlate per-session deny tcp any4 any4
    xlate per-session deny tcp any4 any6
    xlate per-session deny tcp any6 any4
    xlate per-session deny tcp any6 any6
    xlate per-session deny udp any4 any4 eq domain
    xlate per-session deny udp any4 any6 eq domain
    xlate per-session deny udp any6 any4 eq domain
    xlate per-session deny udp any6 any6 eq domain
    xlate per-session deny tcp any4 any4
    xlate per-session deny tcp any4 any6
    xlate per-session deny tcp any6 any4
    xlate per-session deny tcp any6 any6
    xlate per-session deny udp any4 any4 eq domain
    xlate per-session deny udp any4 any6 eq domain
    xlate per-session deny udp any6 any4 eq domain
    xlate per-session deny udp any6 any6 eq domain
    xlate per-session deny tcp any4 any4
    xlate per-session deny tcp any4 any6
    xlate per-session deny tcp any6 any4
    xlate per-session deny tcp any6 any6
    xlate per-session deny udp any4 any4 eq domain
    xlate per-session deny udp any4 any6 eq domain
    xlate per-session deny udp any6 any4 eq domain
    xlate per-session deny udp any6 any6 eq domain
    xlate per-session deny tcp any4 any4
    xlate per-session deny tcp any4 any6
    xlate per-session deny tcp any6 any4
    xlate per-session deny tcp any6 any6
    xlate per-session deny udp any4 any4 eq domain
    xlate per-session deny udp any4 any6 eq domain
    xlate per-session deny udp any6 any4 eq domain
    xlate per-session deny udp any6 any6 eq domain
    passwd ol40hHpZTtZQFXMJ encrypted
    names
    interface Ethernet0/0
     switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
     nameif INSIDE
     security-level 100
     ip address 192.168.111.1 255.255.255.0
    interface Vlan2
     nameif OUTSIDE
     security-level 0
     ip address 205.214.236.50 255.255.255.240
    boot system disk0:/asa902-k8.bin
    boot system disk0:/asa825-k8.bin
    boot system disk0:/asa831-k8.bin
    ftp mode passive
    dns domain-lookup INSIDE
    dns domain-lookup OUTSIDE
    dns server-group DefaultDNS
     name-server 192.168.111.50
     name-server 8.8.8.8
     domain-name scec.local
    object network LAN
     subnet 192.168.111.0 255.255.255.0
    object network SERVER1
     host 192.168.111.50
    object network SERVER1_PUBLIC
     host 205.214.236.51
    object network SERVER2
     host 192.168.111.20
    object network SERVER2_PUBLIC
     host 205.214.236.52
    object network SERVER3
     host 192.168.111.30
    object network SERVER3_PUBLIC
     host 205.214.236.53
    object network SERVER4
     host 192.168.111.40
    object network SERVER4_PUBLIC
     host 205.214.236.54
    object network SERVER5
     host 192.168.111.10
    object network SERVER5_PUBLIC
     host 205.214.236.55
    object-group service SERVER1_PORTS tcp
     port-object eq www
     port-object eq https
     port-object eq smtp
     port-object eq pop3
     port-object eq imap4
     port-object eq 3389
    object-group service SERVER2_PORTS tcp
     port-object eq 3389
    object-group service SERVER3_PORTS tcp
     port-object eq 3389
    object-group service SERVER4_PORTS tcp
     port-object eq 3389
    object-group service SERVER5_PORTS tcp
     port-object eq 3389
     port-object eq www
     port-object eq https
    access-list OUTSIDE_IN extended deny ip 10.0.0.0 255.0.0.0 any log
    access-list OUTSIDE_IN extended deny ip 172.16.0.0 255.240.0.0 any log
    access-list OUTSIDE_IN extended deny ip 192.168.0.0 255.255.0.0 any log
    access-list OUTSIDE_IN extended deny ip 127.0.0.0 255.0.0.0 any log
    access-list OUTSIDE_IN extended deny ip 0.0.0.0 255.255.255.0 any log
    access-list OUTSIDE_IN extended deny ip 244.0.0.0 255.255.255.240 any log
    access-list OUTSIDE_IN extended deny ip host 255.255.255.255 any log
    access-list OUTSIDE_IN extended permit icmp any any echo-reply
    access-list OUTSIDE_IN extended permit icmp any any time-exceeded
    access-list OUTSIDE_IN extended permit icmp any any unreachable
    access-list OUTSIDE_IN extended permit tcp any object SERVER1 object-group SERVER1_PORTS
    access-list OUTSIDE_IN extended permit tcp any object SERVER2 object-group SERVER2_PORTS
    access-list OUTSIDE_IN extended permit tcp any object SERVER3 object-group SERVER3_PORTS
    access-list OUTSIDE_IN extended permit tcp any object SERVER4 object-group SERVER4_PORTS
    access-list OUTSIDE_IN extended permit tcp any object SERVER5 object-group SERVER5_PORTS
    access-list inside-out extended permit ip any any
    pager lines 24
    logging asdm informational
    mtu INSIDE 1500
    mtu OUTSIDE 1500
    ip audit name OUTSIDE_ATTACK attack action alarm drop
    ip audit name OUTSIDE_INFO info action alarm
    ip audit name INSIDE_ATTACK attack action alarm drop reset
    ip audit name INSIDE_INFO info action alarm
    ip audit interface INSIDE INSIDE_INFO
    ip audit interface OUTSIDE OUTSIDE_INFO
    ip audit interface OUTSIDE OUTSIDE_ATTACK
    ip audit signature 2000 disable
    ip audit signature 2001 disable
    ip audit signature 2004 disable
    ip audit signature 2005 disable
    ip audit signature 6051 disable
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-509.bin
    no asdm history enable
    arp timeout 14400
    no arp permit-nonconnected
    nat (INSIDE,OUTSIDE) source static SERVER1 SERVER1_PUBLIC
    nat (INSIDE,OUTSIDE) source static SERVER2 SERVER2_PUBLIC
    nat (INSIDE,OUTSIDE) source static SERVER3 SERVER3_PUBLIC
    nat (INSIDE,OUTSIDE) source static SERVER4 SERVER4_PUBLIC
    nat (INSIDE,OUTSIDE) source static SERVER5 SERVER5_PUBLIC
    object network LAN
     nat (INSIDE,OUTSIDE) dynamic interface
    access-group inside-out in interface INSIDE
    access-group OUTSIDE_IN in interface OUTSIDE
    route OUTSIDE 0.0.0.0 0.0.0.0 205.214.236.49 1
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    aaa authentication ssh console LOCAL
    aaa authentication enable console LOCAL
    aaa authorization exec LOCAL
    http server enable
    http 0.0.0.0 0.0.0.0 INSIDE
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec security-association pmtu-aging infinite
    crypto ca trustpool policy
    telnet timeout 5
    ssh 0.0.0.0 0.0.0.0 INSIDE
    ssh 0.0.0.0 0.0.0.0 OUTSIDE
    ssh timeout 5
    ssh version 2
    console timeout 0
    dhcpd option 3 ip 192.168.111.1
    dhcpd address 192.168.111.100-192.168.111.200 INSIDE
    dhcpd dns 192.168.111.50 8.8.8.8 interface INSIDE
    dhcpd enable INSIDE
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    username wti password OIEBfkGT1DRShCnN encrypted privilege 15
    username admin password g/t7o/eHDKMomDrS encrypted privilege 15
    username vpnuser password 8DcFkqJ9hi39UQw. encrypted privilege 15
    username sysadmin password mi1AUI982JWkJuWt encrypted
    class-map inspection_default
     match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
     parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
     class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    call-home
     profile CiscoTAC-1
      no active
      destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
      destination address email [email protected]
      destination transport-method http
      subscribe-to-alert-group diagnostic
      subscribe-to-alert-group environment
      subscribe-to-alert-group inventory periodic monthly
      subscribe-to-alert-group configuration periodic monthly
      subscribe-to-alert-group telemetry periodic daily
    Cryptochecksum:6dd04d2527e7929343ebd090969e18a1
    : end
    ciscoasa(config)# dir
    Directory of disk0:/
    148    -rwx  15390720     09:08:54 Jul 31 2013  asa825-k8.bin      
    149    -rwx  27611136     09:43:48 Oct 31 2013  asa902-k8.bin
    150    -rwx  2048         00:00:00 Jan 01 1980  FSCK0000.REC
    20     drwx  2048         09:12:16 Jul 31 2013  coredumpinfo
    151    -rwx  16280544     09:14:46 Jul 31 2013  asdm-645.bin
    10     drwx  2048         09:19:42 Jul 31 2013  log
    19     drwx  2048         09:20:08 Jul 31 2013  crypto_archive
    153    -rwx  14240396     14:14:18 Jun 11 2014  asdm-631.bin
    154    -rwx  4096         00:00:00 Jan 01 1980  FSCK0001.REC
    155    -rwx  12998641     09:20:28 Jul 31 2013  csd_3.5.2008-k9.pkg
    156    drwx  2048         09:20:30 Jul 31 2013  sdesktop
    157    -rwx  6487517      09:20:32 Jul 31 2013  anyconnect-macosx-i386-2.5.2014-k9.pkg
    158    -rwx  6689498      09:20:36 Jul 31 2013  anyconnect-linux-2.5.2014-k9.pkg
    159    -rwx  4678691      09:20:38 Jul 31 2013  anyconnect-win-2.5.2014-k9.pkg
    160    -rwx  4096         00:00:00 Jan 01 1980  FSCK0002.REC
    161    -rwx  4096         00:00:00 Jan 01 1980  FSCK0003.REC
    162    -rwx  4096         00:00:00 Jan 01 1980  FSCK0004.REC
    163    -rwx  6144         00:00:00 Jan 01 1980  FSCK0005.REC
    164    -rwx  6144         00:00:00 Jan 01 1980  FSCK0006.REC
    165    -rwx  6144         00:00:00 Jan 01 1980  FSCK0007.REC
    166    -rwx  22528        00:00:00 Jan 01 1980  FSCK0008.REC
    167    -rwx  38912        00:00:00 Jan 01 1980  FSCK0009.REC
    168    -rwx  34816        00:00:00 Jan 01 1980  FSCK0010.REC
    169    -rwx  43008        00:00:00 Jan 01 1980  FSCK0011.REC
    170    -rwx  2048         00:00:00 Jan 01 1980  FSCK0012.REC
    171    -rwx  26624        00:00:00 Jan 01 1980  FSCK0013.REC
    172    -rwx  2048         00:00:00 Jan 01 1980  FSCK0014.REC
    173    -rwx  26624        00:00:00 Jan 01 1980  FSCK0015.REC
    174    -rwx  2048         00:00:00 Jan 01 1980  FSCK0016.REC
    175    -rwx  2505         09:46:08 Oct 31 2013  8_2_5_0_startup_cfg.sav
    176    -rwx  1189         09:46:12 Oct 31 2013  upgrade_startup_errors_201310310946.log
    177    -rwx  100          16:42:40 Jun 10 2014  upgrade_startup_errors_201406101642.log
    178    -rwx  100          14:52:26 Jun 11 2014  upgrade_startup_errors_201406111452.log
    127004672 bytes total (21886976 bytes free)
    Please let me know if you need any other information from me so that i can get our mobile devices to connect to the new CRM from outside the network and allow the owner access on his mobile device to the company cameras.
    ************** (NOTE: I can do both of these things currently from within the network without any issues)*************
    THANKS

    Jgreene -
    This doesn't specifically answer your question, but if you want to get ASDM functionality back you need to load a newer version onto flash memory and then point the ASA to that with the configuration command:
    asdm image disk0:/asdm-version.bin
    You are running  ASA Version 9.0(2) so you need at least version 7 of ASDM to support that.  Interestingly enough your "asdm image" statement in your config points to asdm-509.bin and you have asdm-631.bin and asdm-645.bin on flash.  None of those will work.  I suggest loading up asdm-721.bin and changing the asdm image statement accordingly.  I am pretty sure a reboot is required after that is done.
    Good Luck!
    -Jeff

  • Just need some info

    IMac G5 Repair Extension Program for Video and Power Issues...i read the page that tells how i would now that there is a problem with the Video/Power issues. My serial # is off by 2 digits and I bought my iMac in July but it might have been on the shelf for longer than that.
    Also, I was watching a DVD earlier on the computer today and when i was ejecting the DVD the screen had some horizontal lines or some kind of distortion for about 5 seconds. It's all fine but would this make it eligible for the Repair Extension Program.

    You just bought the machine and from what I can gather its starting to manifest some video problems. I wouldn't worry about the extension I would take it back and get it taken care of plus buy Apple care.

  • I need some input from the iphone community with regards to an App that I'm looking for.

    If anyone has any suggestions I'd appreciate it. If I'm posting in the wrong place, I apologize.
    Many times I take pictures of schedules, reciepts, or itinerary and send it via mms or e-mail to my daughter @college. Often I'd like to "highlight" specific info on the picture, but the apps that let me do this only offer this feature on a PDF file. (I already have goodreader) I have the app Labelbox which would be great in this instance, (I can place labels anywhere on a photo) however, none of the labels they provide are transparent/flourescent. Drawing apps are messy and don't provide the kind of coverage I need for neat highlighting of specific words or sentences. In short, does anyone know of an app that will let me place transparent labels on specific places on a photo? (Being able to change the width or length would also be an added bonus)
    TIA

    Yes. However, some folks like to use the Combo OS updates directly from Apple's Download site rather than going through Software Update.
    BTW: Have you checked the places where you keep your music CDs if you have any?
    If you are using a computer desk, the insall discs should always be kept in a safe place not to far from your computer or at least in a place where all your other computer stuff is.
    All of my CDs relating to my computers are kept in a CD/DVD binder inside my computer desk drawer.

  • REALLY need some help with my problem (Netgear and...

    Hi everyone,
    Well... where to start really.
    This morning around 5am, I lost connection to the net, yet my Netgear (DG834 wired) showed an uptime of 117 hours, so it showed no reboot. It seems my IP profile was raised (As it was low before for my sync).
    I had no reboot it seems, but my noise margin went up to 9db from 6db. This is fine as it means I should be getting around 6.5meg IP profile going by the sync. Anyway (This is complicated to explain but bear with me).
    My current IP profile is now 7.15K. I know this will come down now to match my sync at 9db (Which should be 6.5meg).
    What is happening, is that any change made to my broadband (Like my IP profile being raised this morning) means that I cannot then connect to the net, and anything connected (Like Xbox Live etc) disconnects, even though the router shows no disconnect, and all the lights are green.
    The only way for me to reconnect to the internet then is to MANUALLY reboot the router, because no matter what website etc I try to view, it just says "Looking for..." in the bottom left corner of the browser, and I can't connect to anything like Xbox Live etc.
    Can anyone explain why this is happening with the Netgear router? Shouldn't any change, like an IP profile increase not affect my broadband connection? It seems whenever a change is made BT side, I have to then manually reboot the router to get online.
    I wondered if anyone with a netgear, or anyone with some knowledge on this could tell me why. This could save me a lot of headaches down the line and stop me having noise margin raised etc because I have to manually reboot the router to get it working again. I just thought that any change, like an increase in IP profile etc, shouldn't affect my connnection and force me to have to manually reboot the router to get it up and running again.
    I hope you understood what I was trying to explain, and thanks in advance for any responses.

    Hi John. Thanks for responding.
    I have been through the options on the router and can't find one that says auto connect at all.
    It seems the router is not disconnecting though (Like this morning when the IP profile raised), as the uptime on both WAN and LAN were showing 117 hours, and all green lights were on, on the router. It's just when a change on the BT side is made, it won't let me get on the net until I do a manual reboot. It's all very baffling to me really.
    I tried googling my problem to no avail also.

  • Just needed some clarification regarding the Viewer Builder and actually publishing your App...

    If someone could let me know if my understanding is correct, that'd be a huge help... So I've designed my publication in InDesign and exported the .zip file from the Folio Producer. I've created all of my certificates/splash screens/icons. Lastly, I just recently went through the steps of the Viewer Builder. I'm now at the stage of this process that requires me to purchase the $395 single edition so that I can enter the serial number in the last stage of the Viewer Builder. Now, to my knowledge, once I get the serial number, Viewer Builder will then give me access to an .ipa file and a .zip file. The .ipa file is for me to test on my iPad, and the .zip would be used to distribute to the App Store. I guess this is where I get confused... Let's say after I test the .ipa on my iPad, I don't like some part of my publication. I know how to update my own documents obviously, and I understand that I would have to export another .zip file from the Folio Producer, in turn requiring me to edit the exported folio link in the Viewer Builder. If I had to do that, would I need to purchase another single edition serial number since the original App was edited? Or would the same serial number apply since I'm editing that same App in the Viewer Builder? My next question is somewhat similar. Let's say all of the information is up to date and I go ahead and publish the App to the App Store. However, maybe a month later or some time in the future, I needed to update a phone number or email address--some little detail like that. Again, I understand that I'd have to update the export link in the Viewer Builder, but would I then need to create a new app since my app was already published? Would I then have to purchase another $395 single edition serial number just so that I can update my information? This seems to be the only thing in this whole process that I could use some clarification on so that I don't run into any surprises in the future. Any help would be great, thanks!

    Hi Joshua,
    When you have purchased the serial, you can rebuild your app with your updated content, as long as you use the same bundleID (applicationID), that is tied to your Apple mobile provisioning profile. The serial number is valid for a one year period.
    After you have submitted your app to Apple and it has been approved, please read: http://forums.adobe.com/message/4172167#4172167
    With kind regards,
    Klaasjan Tukker
    Adobe Systems

  • Need some opinions on my problem

    well once in a while my screen looks like it shuts off and i can't do anything.. Its really rare. but when i got another 512 of kreton it did it all the time so i rma'd it.. im just wondering if getting a tested brand of ram would help my problem.. or is my psu bad? any feed back is appreciated

    Calculate your needs here:
    http://www.jscustompcs.com/power_supply/
    I have two of the Antec SL-400's.
    You can probably get by with it, but might want more if you have unlisted hardware or plan to upgrade/expand significantly.
    It calculates to be barely adequate for the P4 rig.  The link above says I should have 411 watts.  I don't use it hard, so I'm doing all right, so far.
    Many fellers here highly recommend the Enermax 465, 33a@12volts:
    http://www.newegg.com/app/ViewProduct.asp?submit=manufactory&catalog=58&manufactory=1400&DEPA=0&sortby=14&order=1
    The AMD rig calcs out at 350 watts, so I'm OK.

Maybe you are looking for

  • Add Forecasting column to a Query

    Hi, The user wants to add a forecasting column to a query that has the actual and plan costs. He wants the option to change the values of this column in the query. Can I use any planning cubes for this? My plan is to make a copy of the cube that has

  • Problem with boot commands on G3 iMac

    My iMac G3 will not accept any boot commands like "C" or "CMD, ALT, P, R" etc... etc... when using the original Apple PRO keyboard. The Pro keyboard is fine and all the keys work in OS X. For the sake of it i tried another keyboard from my Power Mac

  • Impdp exclude=schema

    hi all, i have written this EXCLUDE=SCHEMA:"='ORDERS'" but it is not working... i even tried like this EXCLUDE=SCHEMA:\"='ORDERS'\" but i am getting error like "ORDERS" is INVALID identifier. so can any body please tell me how to user schema name in

  • Booting from RAM

    I was trying to follow this guide to configure my system to load my root partition to RAM on startup. I get stuck at the: cd /usr/share/initramfs-tools/scripts/ part. Does anyone know how I can finish this guide? or perhaps know about a guide that su

  • Sky Go - Use Silverlight Fullscreen Pinning Mode

    I have two monitors, and I often watch Sky Go on monitor A while working on monitor B. However, whenever I fullscreen Sky Go, and click on a second monitor, Sky Go exits fullscreen mode. Silverlight has had Fullscreen Pinning Mode (where it remains f